Merge tag 'stm32-dt-for-v6.6-1' of...

Merge tag 'stm32-dt-for-v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt

STM32 DT for v6.6, round 1

Highlights:
----------

- MCU:
  - Add CAN support on stm32f746.
  - Add touchscreen support (edt-ft5306) on stm32f746-disco.
  - Add support to Rocktech RK043FN48H display on stm32f746-disco
    board.
  - Add gpio-ranges for stm32f7 to fix boot issue.

- MPU:
  - STM32MP13:
    - Remove shmem for scmi-optee to match with OP-TEE configuration.
    - Enable OP-TEE asynchronous notification by using PPI#15.
    - Expose and use SCMI regulators on stm32mp135f-dk.

  - STMP32MP15:
    - Remove shmem for scmi-optee to match with OPTEE configuration
    - Deduplicate DSI node to fix  #address-cells/#size-cells issue on
      boards using it.

  - ST:
    - Fix dts check warnings on stm32mp15-scmi boards.

  - DH:
    - Add missing detach mailbox for DHCOM and DHCOR SoM.

  - Odyssey:
    - Add missing detach mailbox for Odyssey SoM.

  - OCTAVO:
    - Add Linux Automation Test Automation Controller (LXA TAC) based
      on Octavo Systems OSD32MP15x SiP. It contains: eMMC,
      DSA-capable ETH switch (2 ports), dual CAN...
      It adds two boards support: lxa-tac-gen1 and lxa-tac-gen2 based
      on STM32MP157.

  - PROTONIC:
    - Add Power over Data Line (PoDL) Power Source Equipment (PSE)
      regulator nodes on PRTT1C board. It allows power delivery and
      data transmission over a single twisted pair.

* tag 'stm32-dt-for-v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (29 commits)
  ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
  ARM: dts: stm32: STM32MP13x SoC exposes SCMI regulators
  dt-bindings: rcc: stm32: add STM32MP13 SCMI regulators IDs
  ARM: dts: stm32: support display on stm32f746-disco board
  ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
  ARM: dts: stm32: add pin map for LTDC on stm32f7
  ARM: dts: stm32: add ltdc support on stm32f746 MCU
  ARM: dts: st: Add gpio-ranges for stm32f769-pinctrl
  ARM: dts: st: Add gpio-ranges for stm32f746-pinctrl
  ARM: dts: st: stm32mp157c-emstamp: correct regulator-active-discharge
  ARM: dts: st: stm32mp157c-emstamp: drop incorrect vref_ddr property
  ARM: dts: stm32: fix dts check warnings on stm32mp15-scmi
  ARM: dts: stm32: Add missing detach mailbox for DHCOR SoM
  ARM: dts: stm32: Add missing detach mailbox for DHCOM SoM
  ARM: dts: stm32: Add missing detach mailbox for Odyssey SoM
  ARM: dts: stm32: Add missing detach mailbox for emtrion emSBC-Argon
  ARM: dts: stm32: prtt1c: Add PoDL PSE regulator nodes
  ARM: dts: stm32: add touchscreen on stm32f746-disco board
  ARM: dts: stm32: add pin map for i2c3 controller on stm32f7
  ARM: dts: stm32: re-add CAN support on stm32f746
  ...

Link: https://lore.kernel.org/r/c0524a16-ab27-0cb5-8e7b-c12f7bde7e0d@foss.st.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/arm/stm32/stm32.yaml

@@ -143,7 +143,9 @@ properties:
       - description: Octavo OSD32MP15x System-in-Package based boards
         items:
           - enum:
-              - lxa,stm32mp157c-mc1 # Linux Automation MC-1
+              - lxa,stm32mp157c-mc1      # Linux Automation MC-1
+              - lxa,stm32mp157c-tac-gen1 # Linux Automation TAC (Generation 1)
+              - lxa,stm32mp157c-tac-gen2 # Linux Automation TAC (Generation 2)
           - const: oct,stm32mp15xx-osd32
           - enum:
               - st,stm32mp157

Documentation/devicetree/bindings/net/can/bosch,m_can.yaml

@@ -128,7 +128,7 @@ required:
   - clock-names
   - bosch,mram-cfg
 
-additionalProperties: false
+unevaluatedProperties: false
 
 examples:
   - |

Documentation/devicetree/bindings/net/dsa/microchip,ksz.yaml

@@ -49,6 +49,9 @@ properties:
       Set if the output SYNCLKO clock should be disabled. Do not mix with
       microchip,synclko-125.
 
+  interrupts:
+    maxItems: 1
+
 required:
   - compatible
   - reg

arch/arm/boot/dts/st/Makefile

@@ -56,6 +56,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
 	stm32mp157c-ev1.dtb \
 	stm32mp157c-ev1-scmi.dtb \
 	stm32mp157c-lxa-mc1.dtb \
+	stm32mp157c-lxa-tac-gen1.dtb \
+	stm32mp157c-lxa-tac-gen2.dtb \
 	stm32mp157c-odyssey.dtb \
 	stm32mp157c-phycore-stm32mp1-3.dtb
 dtb-$(CONFIG_ARCH_U8500) += \

arch/arm/boot/dts/st/stm32f7-pinctrl.dtsi

@@ -171,6 +171,16 @@ pins {
 				};
 			};
 
+			i2c3_pins_a: i2c3-0 {
+				pins {
+					pinmux = <STM32_PINMUX('H', 8, AF4)>, /* I2C3_SDA */
+						 <STM32_PINMUX('H', 7, AF4)>; /* I2C3_SCL */
+					bias-disable;
+					drive-open-drain;
+					slew-rate = <0>;
+				};
+			};
+
 			usbotg_hs_pins_a: usbotg-hs-0 {
 				pins {
 					pinmux = <STM32_PINMUX('H', 4, AF10)>, /* OTG_HS_ULPI_NXT */
@@ -365,6 +375,41 @@ pins2 {
 					bias-pull-up;
 				};
 			};
+
+
+			ltdc_pins_a: ltdc-0 {
+				pins {
+					pinmux = <STM32_PINMUX('E', 4, AF14)>, /* LCD_B0 */
+						 <STM32_PINMUX('G',12, AF9)>,  /* LCD_B4 */
+						 <STM32_PINMUX('I', 9, AF14)>, /* LCD_VSYNC */
+						 <STM32_PINMUX('I',10, AF14)>, /* LCD_HSYNC */
+						 <STM32_PINMUX('I',14, AF14)>, /* LCD_CLK */
+						 <STM32_PINMUX('I',15, AF14)>, /* LCD_R0 */
+						 <STM32_PINMUX('J', 0, AF14)>, /* LCD_R1 */
+						 <STM32_PINMUX('J', 1, AF14)>, /* LCD_R2 */
+						 <STM32_PINMUX('J', 2, AF14)>, /* LCD_R3 */
+						 <STM32_PINMUX('J', 3, AF14)>, /* LCD_R4 */
+						 <STM32_PINMUX('J', 4, AF14)>, /* LCD_R5 */
+						 <STM32_PINMUX('J', 5, AF14)>, /* LCD_R6 */
+						 <STM32_PINMUX('J', 6, AF14)>, /* LCD_R7 */
+						 <STM32_PINMUX('J', 7, AF14)>, /* LCD_G0 */
+						 <STM32_PINMUX('J', 8, AF14)>, /* LCD_G1 */
+						 <STM32_PINMUX('J', 9, AF14)>, /* LCD_G2 */
+						 <STM32_PINMUX('J',10, AF14)>, /* LCD_G3 */
+						 <STM32_PINMUX('J',11, AF14)>, /* LCD_G4 */
+						 <STM32_PINMUX('J',13, AF14)>, /* LCD_B1 */
+						 <STM32_PINMUX('J',14, AF14)>, /* LCD_B2 */
+						 <STM32_PINMUX('J',15, AF14)>, /* LCD_B3 */
+						 <STM32_PINMUX('K', 0, AF14)>, /* LCD_G5 */
+						 <STM32_PINMUX('K', 1, AF14)>, /* LCD_G6 */
+						 <STM32_PINMUX('K', 2, AF14)>, /* LCD_G7 */
+						 <STM32_PINMUX('K', 4, AF14)>, /* LCD_B5 */
+						 <STM32_PINMUX('K', 5, AF14)>, /* LCD_B6 */
+						 <STM32_PINMUX('K', 6, AF14)>, /* LCD_B7 */
+						 <STM32_PINMUX('K', 7, AF14)>; /* LCD_DE */
+					slew-rate = <2>;
+				};
+			};
 		};
 	};
 };

arch/arm/boot/dts/st/stm32f746-disco.dts

@@ -43,8 +43,9 @@
 /dts-v1/;
 #include "stm32f746.dtsi"
 #include "stm32f746-pinctrl.dtsi"
-#include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "STMicroelectronics STM32F746-DISCO board";
@@ -60,6 +61,19 @@ memory@c0000000 {
 		reg = <0xC0000000 0x800000>;
 	};
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			no-map;
+			size = <0x80000>;
+			linux,dma-default;
+		};
+	};
+
 	aliases {
 		serial0 = &usart1;
 	};
@@ -79,12 +93,31 @@ vcc5v_otg_fs: vcc5v-otg-fs-regulator {
 		regulator-always-on;
 	};
 
-	mmc_vcard: mmc_vcard {
+	vcc_3v3: vcc-3v3 {
 		compatible = "regulator-fixed";
-		regulator-name = "mmc_vcard";
+		regulator-name = "vcc_3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpiok 3 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+
+	panel_rgb: panel-rgb {
+		compatible = "rocktech,rk043fn48h";
+		power-supply = <&vcc_3v3>;
+		backlight = <&backlight>;
+		enable-gpios = <&gpioi 12 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+		port {
+			panel_in_rgb: endpoint {
+				remote-endpoint = <&ltdc_out_rgb>;
+			};
+		};
+	};
 };
 
 &clk_hse {
@@ -99,9 +132,37 @@ &i2c1 {
 	status = "okay";
 };
 
+&i2c3 {
+	pinctrl-0 = <&i2c3_pins_a>;
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5306";
+		reg = <0x38>;
+		interrupt-parent = <&gpioi>;
+		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <272>;
+	};
+};
+
+&ltdc {
+	pinctrl-0 = <&ltdc_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	port {
+		ltdc_out_rgb: endpoint {
+			remote-endpoint = <&panel_in_rgb>;
+		};
+	};
+};
+
 &sdio1 {
 	status = "okay";
-	vmmc-supply = <&mmc_vcard>;
+	vmmc-supply = <&vcc_3v3>;
 	cd-gpios = <&gpioc 13 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default", "opendrain";
 	pinctrl-0 = <&sdio_pins_a>;

arch/arm/boot/dts/st/stm32f746-pinctrl.dtsi

@@ -8,4 +8,48 @@
 
 &pinctrl {
 	compatible = "st,stm32f746-pinctrl";
+
+	gpioa: gpio@40020000 {
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@40020400 {
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@40020800 {
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@40020c00 {
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@40021000 {
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@40021400 {
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@40021800 {
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@40021c00 {
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
+
+	gpioi: gpio@40022000 {
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
+
+	gpioj: gpio@40022400 {
+		gpio-ranges = <&pinctrl 0 144 16>;
+	};
+
+	gpiok: gpio@40022800 {
+		gpio-ranges = <&pinctrl 0 160 8>;
+	};
 };

arch/arm/boot/dts/st/stm32f746.dtsi

@@ -257,6 +257,23 @@ rtc: rtc@40002800 {
 			status = "disabled";
 		};
 
+		can3: can@40003400 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40003400 0x200>;
+			interrupts = <104>, <105>, <106>, <107>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F7_APB1_RESET(CAN3)>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN3)>;
+			st,gcan = <&gcan3>;
+			status = "disabled";
+		};
+
+		gcan3: gcan@40003600 {
+			compatible = "st,stm32f4-gcan", "syscon";
+			reg = <0x40003600 0x200>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN3)>;
+		};
+
 		usart2: serial@40004400 {
 			compatible = "st,stm32f7-uart";
 			reg = <0x40004400 0x400>;
@@ -337,6 +354,36 @@ i2c4: i2c@40006000 {
 			status = "disabled";
 		};
 
+		can1: can@40006400 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40006400 0x200>;
+			interrupts = <19>, <20>, <21>, <22>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F7_APB1_RESET(CAN1)>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN1)>;
+			st,can-primary;
+			st,gcan = <&gcan1>;
+			status = "disabled";
+		};
+
+		gcan1: gcan@40006600 {
+			compatible = "st,stm32f4-gcan", "syscon";
+			reg = <0x40006600 0x200>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN1)>;
+		};
+
+		can2: can@40006800 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40006800 0x200>;
+			interrupts = <63>, <64>, <65>, <66>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F7_APB1_RESET(CAN2)>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(CAN2)>;
+			st,can-secondary;
+			st,gcan = <&gcan1>;
+			status = "disabled";
+		};
+
 		cec: cec@40006c00 {
 			compatible = "st,stm32-cec";
 			reg = <0x40006C00 0x400>;
@@ -507,6 +554,16 @@ pwm {
 			};
 		};
 
+		ltdc: display-controller@40016800 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x40016800 0x200>;
+			interrupts = <88>, <89>;
+			resets = <&rcc STM32F7_APB2_RESET(LTDC)>;
+			clocks = <&rcc 1 CLK_LCD>;
+			clock-names = "lcd";
+			status = "disabled";
+		};
+
 		pwrcfg: power-config@40007000 {
 			compatible = "st,stm32-power-config", "syscon";
 			reg = <0x40007000 0x400>;

arch/arm/boot/dts/st/stm32f769-pinctrl.dtsi

@@ -8,4 +8,48 @@
 
 &pinctrl {
 	compatible = "st,stm32f769-pinctrl";
+
+	gpioa: gpio@40020000 {
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@40020400 {
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@40020800 {
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@40020c00 {
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@40021000 {
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@40021400 {
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@40021800 {
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@40021c00 {
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
+
+	gpioi: gpio@40022000 {
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
+
+	gpioj: gpio@40022400 {
+		gpio-ranges = <&pinctrl 0 144 16>;
+	};
+
+	gpiok: gpio@40022800 {
+		gpio-ranges = <&pinctrl 0 160 8>;
+	};
 };

arch/arm/boot/dts/st/stm32mp131.dtsi

@@ -33,6 +33,8 @@ firmware {
 		optee {
 			method = "smc";
 			compatible = "linaro,optee-tz";
+			interrupt-parent = <&intc>;
+			interrupts = <GIC_PPI 15 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
 		};
 
 		scmi: scmi {
@@ -40,7 +42,6 @@ scmi: scmi {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			linaro,optee-channel-id = <0>;
-			shmem = <&scmi_shm>;
 
 			scmi_clk: protocol@14 {
 				reg = <0x14>;
@@ -51,6 +52,28 @@ scmi_reset: protocol@16 {
 				reg = <0x16>;
 				#reset-cells = <1>;
 			};
+
+			scmi_voltd: protocol@17 {
+				reg = <0x17>;
+
+				scmi_regu: regulators {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					scmi_reg11: regulator@0 {
+						reg = <VOLTD_SCMI_REG11>;
+						regulator-name = "reg11";
+					};
+					scmi_reg18: regulator@1 {
+						reg = <VOLTD_SCMI_REG18>;
+						regulator-name = "reg18";
+					};
+					scmi_usb33: regulator@2 {
+						reg = <VOLTD_SCMI_USB33>;
+						regulator-name = "usb33";
+					};
+				};
+			};
 		};
 	};
 
@@ -77,28 +100,6 @@ timer {
 		always-on;
 	};
 
-	/* PWR 1v1, 1v8 and 3v3 regulators defined as fixed, waiting for SCMI */
-	reg11: reg11 {
-		compatible = "regulator-fixed";
-		regulator-name = "reg11";
-		regulator-min-microvolt = <1100000>;
-		regulator-max-microvolt = <1100000>;
-	};
-
-	reg18: reg18 {
-		compatible = "regulator-fixed";
-		regulator-name = "reg18";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	usb33: usb33 {
-		compatible = "regulator-fixed";
-		regulator-name = "usb33";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -106,19 +107,6 @@ soc {
 		interrupt-parent = <&intc>;
 		ranges;
 
-		scmi_sram: sram@2ffff000 {
-			compatible = "mmio-sram";
-			reg = <0x2ffff000 0x1000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x2ffff000 0x1000>;
-
-			scmi_shm: scmi-sram@0 {
-				compatible = "arm,scmi-shmem";
-				reg = <0 0x80>;
-			};
-		};
-
 		timers2: timer@40000000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -813,7 +801,7 @@ usbotg_hs: usb@49000000 {
 			g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
 			dr_mode = "otg";
 			otg-rev = <0x200>;
-			usb33d-supply = <&usb33>;
+			usb33d-supply = <&scmi_usb33>;
 			status = "disabled";
 		};
 
@@ -1343,8 +1331,8 @@ usbphyc: usbphyc@5a006000 {
 			reg = <0x5a006000 0x1000>;
 			clocks = <&rcc USBPHY_K>;
 			resets = <&rcc USBPHY_R>;
-			vdda1v1-supply = <&reg11>;
-			vdda1v8-supply = <&reg18>;
+			vdda1v1-supply = <&scmi_reg11>;
+			vdda1v8-supply = <&scmi_reg18>;
 			status = "disabled";
 
 			usbphyc_port0: usb-phy@0 {

arch/arm/boot/dts/st/stm32mp135f-dk.dts

@@ -9,6 +9,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/st,stm32mp13-regulator.h>
 #include "stm32mp135.dtsi"
 #include "stm32mp13xf.dtsi"
 #include "stm32mp13-pinctrl.dtsi"
@@ -65,45 +66,13 @@ led-blue {
 			default-state = "off";
 		};
 	};
-
-	v3v3_sw: v3v3-sw {
-		compatible = "regulator-fixed";
-		regulator-name = "v3v3_sw";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	vdd_adc: vdd-adc {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_adc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	vdd_sd: vdd-sd {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_sd";
-		regulator-min-microvolt = <2900000>;
-		regulator-max-microvolt = <2900000>;
-		regulator-always-on;
-	};
-
-	vdd_usb: vdd-usb {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_usb";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
 };
 
 &adc_1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&adc1_usb_cc_pins_a>;
-	vdda-supply = <&vdd_adc>;
-	vref-supply = <&vdd_adc>;
+	vdda-supply = <&scmi_vdd_adc>;
+	vref-supply = <&scmi_vdd_adc>;
 	status = "okay";
 	adc1: adc@0 {
 		status = "okay";
@@ -195,6 +164,29 @@ &rtc {
 	status = "okay";
 };
 
+&scmi_regu {
+	scmi_vdd_adc: regulator@10 {
+		reg = <VOLTD_SCMI_STPMIC1_LDO1>;
+		regulator-name = "vdd_adc";
+	};
+	scmi_vdd_usb: regulator@13 {
+		reg = <VOLTD_SCMI_STPMIC1_LDO4>;
+		regulator-name = "vdd_usb";
+	};
+	scmi_vdd_sd: regulator@14 {
+		reg = <VOLTD_SCMI_STPMIC1_LDO5>;
+		regulator-name = "vdd_sd";
+	};
+	scmi_v1v8_periph: regulator@15 {
+		reg = <VOLTD_SCMI_STPMIC1_LDO6>;
+		regulator-name = "v1v8_periph";
+	};
+	scmi_v3v3_sw: regulator@19 {
+		reg = <VOLTD_SCMI_STPMIC1_PWR_SW2>;
+		regulator-name = "v3v3_sw";
+	};
+};
+
 &sdmmc1 {
 	pinctrl-names = "default", "opendrain", "sleep";
 	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>;
@@ -204,7 +196,7 @@ &sdmmc1 {
 	disable-wp;
 	st,neg-edge;
 	bus-width = <4>;
-	vmmc-supply = <&vdd_sd>;
+	vmmc-supply = <&scmi_vdd_sd>;
 	status = "okay";
 };
 
@@ -321,7 +313,7 @@ &usbh_ehci {
 	hub@1 {
 		compatible = "usb424,2514";
 		reg = <1>;
-		vdd-supply = <&v3v3_sw>;
+		vdd-supply = <&scmi_v3v3_sw>;
 	};
 };
 
@@ -342,7 +334,7 @@ &usbphyc {
 };
 
 &usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
+	phy-supply = <&scmi_vdd_usb>;
 	st,current-boost-microamp = <1000>;
 	st,decrease-hs-slew-rate;
 	st,tune-hs-dc-level = <2>;
@@ -356,7 +348,7 @@ &usbphyc_port0 {
 };
 
 &usbphyc_port1 {
-	phy-supply = <&vdd_usb>;
+	phy-supply = <&scmi_vdd_usb>;
 	st,current-boost-microamp = <1000>;
 	st,decrease-hs-slew-rate;
 	st,tune-hs-dc-level = <2>;

arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi

@@ -6,6 +6,17 @@
 #include <dt-bindings/pinctrl/stm32-pinfunc.h>
 
 &pinctrl {
+	adc1_ain_pins_a: adc1-ain-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 11, ANALOG)>, /* ADC1_INP2 */
+				 <STM32_PINMUX('B', 1, ANALOG)>, /* ADC1_INP5 */
+				 <STM32_PINMUX('B', 0, ANALOG)>, /* ADC1_INP9 */
+				 <STM32_PINMUX('C', 0, ANALOG)>, /* ADC1_INP10 */
+				 <STM32_PINMUX('C', 3, ANALOG)>, /* ADC1_INP13 */
+				 <STM32_PINMUX('A', 3, ANALOG)>; /* ADC1_INP15 */
+		};
+	};
+
 	adc1_in6_pins_a: adc1-in6-0 {
 		pins {
 			pinmux = <STM32_PINMUX('F', 12, ANALOG)>;
@@ -391,6 +402,46 @@ pins1 {
 		};
 	};
 
+	ethernet0_rgmii_pins_e: rgmii-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, AF11)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, AF11)>; /* ETH_RGMII_TX_CTL */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 7, AF11)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+		};
+	};
+
+	ethernet0_rgmii_sleep_pins_e: rgmii-sleep-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 7, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+		};
+	};
+
 	ethernet0_rmii_pins_a: rmii-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
@@ -1154,6 +1205,20 @@ pins {
 		};
 	};
 
+	pwm1_pins_c: pwm1-2 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 11, AF1)>; /* TIM1_CH2 */
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm1_sleep_pins_c: pwm1-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 11, ANALOG)>; /* TIM1_CH2 */
+		};
+	};
+
 	pwm2_pins_a: pwm2-0 {
 		pins {
 			pinmux = <STM32_PINMUX('A', 3, AF1)>; /* TIM2_CH4 */
@@ -1280,6 +1345,26 @@ pins {
 		};
 	};
 
+	pwm8_pins_b: pwm8-1 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 5, AF3)>, /* TIM8_CH1 */
+				 <STM32_PINMUX('I', 6, AF3)>, /* TIM8_CH2 */
+				 <STM32_PINMUX('I', 7, AF3)>, /* TIM8_CH3 */
+				 <STM32_PINMUX('C', 9, AF3)>; /* TIM8_CH4 */
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm8_sleep_pins_b: pwm8-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 5, ANALOG)>, /* TIM8_CH1 */
+				 <STM32_PINMUX('I', 6, ANALOG)>, /* TIM8_CH2 */
+				 <STM32_PINMUX('I', 7, ANALOG)>, /* TIM8_CH3 */
+				 <STM32_PINMUX('C', 9, ANALOG)>; /* TIM8_CH4 */
+		};
+	};
+
 	pwm12_pins_a: pwm12-0 {
 		pins {
 			pinmux = <STM32_PINMUX('H', 6, AF2)>; /* TIM12_CH1 */
@@ -2074,6 +2159,20 @@ pins2 {
 		};
 	};
 
+	spi2_pins_c: spi2-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('I', 1, AF5)>, /* SPI2_SCK */
+				 <STM32_PINMUX('I', 3, AF5)>; /* SPI2_MOSI */
+			bias-disable;
+			drive-push-pull;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 2, AF5)>; /* SPI2_MISO */
+			bias-pull-down;
+		};
+	};
+
 	spi4_pins_a: spi4-0 {
 		pins {
 			pinmux = <STM32_PINMUX('E', 12, AF5)>, /* SPI4_SCK */
@@ -2088,6 +2187,21 @@ pins2 {
 		};
 	};
 
+	spi5_pins_a: spi5-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 7, AF5)>, /* SPI5_SCK */
+				 <STM32_PINMUX('F', 9, AF5)>; /* SPI5_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 8, AF5)>; /* SPI5_MISO */
+			bias-disable;
+		};
+	};
+
 	stusb1600_pins_a: stusb1600-0 {
 		pins {
 			pinmux = <STM32_PINMUX('I', 11, GPIO)>;
@@ -2578,6 +2692,21 @@ pins {
 		};
 	};
 
+	usart3_pins_f: usart3-5 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('D', 12, AF7)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
+				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+			bias-disable;
+		};
+	};
+
 	usbotg_hs_pins_a: usbotg-hs-0 {
 		pins {
 			pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */

arch/arm/boot/dts/st/stm32mp15-scmi.dtsi

@@ -16,7 +16,6 @@ scmi: scmi {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			linaro,optee-channel-id = <0>;
-			shmem = <&scmi_shm>;
 
 			scmi_clk: protocol@14 {
 				reg = <0x14>;
@@ -35,22 +34,21 @@ scmi_reguls: regulators {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					scmi_reg11: reg11@0 {
+					scmi_reg11: regulator@0 {
 						reg = <0>;
 						regulator-name = "reg11";
 						regulator-min-microvolt = <1100000>;
 						regulator-max-microvolt = <1100000>;
 					};
 
-					scmi_reg18: reg18@1 {
-						voltd-name = "reg18";
+					scmi_reg18: regulator@1 {
 						reg = <1>;
 						regulator-name = "reg18";
 						regulator-min-microvolt = <1800000>;
 						regulator-max-microvolt = <1800000>;
 					};
 
-					scmi_usb33: usb33@2 {
+					scmi_usb33: regulator@2 {
 						reg = <2>;
 						regulator-name = "usb33";
 						regulator-min-microvolt = <3300000>;
@@ -60,21 +58,6 @@ scmi_usb33: usb33@2 {
 			};
 		};
 	};
-
-	soc {
-		scmi_sram: sram@2ffff000 {
-			compatible = "mmio-sram";
-			reg = <0x2ffff000 0x1000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x2ffff000 0x1000>;
-
-			scmi_shm: scmi-sram@0 {
-				compatible = "arm,scmi-shmem";
-				reg = <0 0x80>;
-			};
-		};
-	};
 };
 
 &reg11 {

arch/arm/boot/dts/st/stm32mp151a-prtt1c.dts

@@ -23,6 +23,18 @@ clock_sja1105: clock-sja1105 {
 		clock-frequency = <25000000>;
 	};
 
+	pse_t1l1: ethernet-pse-1 {
+		compatible = "podl-pse-regulator";
+		pse-supply = <&reg_t1l1>;
+		#pse-cells = <0>;
+	};
+
+	pse_t1l2: ethernet-pse-2 {
+		compatible = "podl-pse-regulator";
+		pse-supply = <&reg_t1l2>;
+		#pse-cells = <0>;
+	};
+
 	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		#address-cells = <1>;
@@ -32,6 +44,24 @@ mdio0: mdio {
 
 	};
 
+	reg_t1l1: regulator-pse-t1l1 {
+		compatible = "regulator-fixed";
+		regulator-name = "pse-t1l1";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpiog 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_t1l2: regulator-pse-t1l2 {
+		compatible = "regulator-fixed";
+		regulator-name = "pse-t1l2";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpiog 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	wifi_pwrseq: wifi-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpiod 8 GPIO_ACTIVE_LOW>;
@@ -92,6 +122,7 @@ t1l1_phy: ethernet-phy@7 {
 		reset-gpios = <&gpiog 12 GPIO_ACTIVE_LOW>;
 		reset-assert-us = <10>;
 		reset-deassert-us = <35>;
+		pses = <&pse_t1l1>;
 	};
 
 	/* TI DP83TD510E */
@@ -102,6 +133,7 @@ t1l2_phy: ethernet-phy@10 {
 		reset-gpios = <&gpiog 11 GPIO_ACTIVE_LOW>;
 		reset-assert-us = <10>;
 		reset-deassert-us = <35>;
+		pses = <&pse_t1l2>;
 	};
 
 	/* Micrel KSZ9031 */

arch/arm/boot/dts/st/stm32mp157.dtsi

@@ -22,9 +22,27 @@ dsi: dsi@5a000000 {
 			reg = <0x5a000000 0x800>;
 			clocks = <&rcc DSI_K>, <&clk_hse>, <&rcc DSI_PX>;
 			clock-names = "pclk", "ref", "px_clk";
+			phy-dsi-supply = <&reg18>;
 			resets = <&rcc DSI_R>;
 			reset-names = "apb";
 			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					dsi_in: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					dsi_out: endpoint {
+					};
+				};
+			};
 		};
 	};
 };

arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2-of10.dts

@@ -46,26 +46,14 @@ panel_in_lvds: endpoint {
 
 &dsi {
 	status = "okay";
-	phy-dsi-supply = <&reg18>;
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
+};
 
-		port@0 {
-			reg = <0>;
-			dsi_in: endpoint {
-				remote-endpoint = <&ltdc_ep0_out>;
-			};
-		};
+&dsi_in {
+	remote-endpoint = <&ltdc_ep0_out>;
+};
 
-		port@1 {
-			reg = <1>;
-			dsi_out: endpoint {
-				remote-endpoint = <&bridge_in>;
-			};
-		};
-	};
+&dsi_out {
+	remote-endpoint = <&bridge_in>;
 };
 
 &i2c6 {

arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-edimm2.2.dts

@@ -46,26 +46,14 @@ panel_out_bridge: endpoint {
 
 &dsi {
 	status = "okay";
-	phy-dsi-supply = <&reg18>;
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
+};
 
-		port@0 {
-			reg = <0>;
-			dsi_in_ltdc: endpoint {
-				remote-endpoint = <&ltdc_out_dsi>;
-			};
-		};
+&dsi_in {
+	remote-endpoint = <&ltdc_out_dsi>;
+};
 
-		port@1 {
-			reg = <1>;
-			dsi_out_bridge: endpoint {
-				remote-endpoint = <&bridge_in_dsi>;
-			};
-		};
-	};
+&dsi_out {
+	remote-endpoint = <&bridge_in_dsi>;
 };
 
 &i2c6 {
@@ -88,7 +76,7 @@ ports {
 			port@0 {
 				reg = <0>;
 				bridge_in_dsi: endpoint {
-					remote-endpoint = <&dsi_out_bridge>;
+					remote-endpoint = <&dsi_out>;
 					data-lanes = <1 2>;
 				};
 			};
@@ -108,7 +96,7 @@ &ltdc {
 
 	port {
 		ltdc_out_dsi: endpoint {
-			remote-endpoint = <&dsi_in_ltdc>;
+			remote-endpoint = <&dsi_in>;
 		};
 	};
 };

arch/arm/boot/dts/st/stm32mp157c-dk2.dts

@@ -34,26 +34,6 @@ &dsi {
 	#address-cells = <1>;
 	#size-cells = <0>;
 	status = "okay";
-	phy-dsi-supply = <&reg18>;
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-			dsi_in: endpoint {
-				remote-endpoint = <&ltdc_ep1_out>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-			dsi_out: endpoint {
-				remote-endpoint = <&panel_in>;
-			};
-		};
-	};
 
 	panel@0 {
 		compatible = "orisetech,otm8009a";
@@ -70,6 +50,14 @@ panel_in: endpoint {
 	};
 };
 
+&dsi_in {
+	remote-endpoint = <&ltdc_ep1_out>;
+};
+
+&dsi_out {
+	remote-endpoint = <&panel_in>;
+};
+
 &i2c1 {
 	touchscreen@38 {
 		compatible = "focaltech,ft6236";

arch/arm/boot/dts/st/stm32mp157c-emstamp-argon.dtsi

@@ -310,7 +310,6 @@ vdda: ldo6 {
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
 			bst_out: boost {
@@ -321,7 +320,7 @@ bst_out: boost {
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 
 			vbus_usbh: pwr_sw2 {
@@ -368,8 +367,8 @@ &iwdg2 {
 &m4_rproc {
 	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
 			<&vdev0vring1>, <&vdev0buffer>;
-	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
-	mbox-names = "vq0", "vq1", "shutdown";
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
 	interrupt-parent = <&exti>;
 	interrupts = <68 1>;
 	interrupt-names = "wdg";

arch/arm/boot/dts/st/stm32mp157c-ev1.dts

@@ -100,30 +100,10 @@ dcmi_0: endpoint {
 };
 
 &dsi {
-	phy-dsi-supply = <&reg18>;
 	#address-cells = <1>;
 	#size-cells = <0>;
 	status = "okay";
 
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-			dsi_in: endpoint {
-				remote-endpoint = <&ltdc_ep0_out>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-			dsi_out: endpoint {
-				remote-endpoint = <&dsi_panel_in>;
-			};
-		};
-	};
-
 	panel@0 {
 		compatible = "raydium,rm68200";
 		reg = <0>;
@@ -140,6 +120,14 @@ dsi_panel_in: endpoint {
 	};
 };
 
+&dsi_in {
+	remote-endpoint = <&ltdc_ep0_out>;
+};
+
+&dsi_out {
+	remote-endpoint = <&dsi_panel_in>;
+};
+
 &ethernet0 {
 	status = "okay";
 	pinctrl-0 = <&ethernet0_rgmii_pins_a>;

arch/arm/boot/dts/st/stm32mp157c-lxa-tac-gen1.dts

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc-lxa-tac.dtsi"
+
+/ {
+	model = "Linux Automation Test Automation Controller (TAC) Gen 1";
+	compatible = "lxa,stm32mp157c-tac-gen1", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&v3v3>;
+
+		brightness-levels = <0 31 63 95 127 159 191 223 255>;
+		default-brightness-level = <7>;
+		pwms = <&backlight_pwm 1 1000000 0>;
+	};
+
+	reg_iobus_12v: regulator-iobus-12v {
+		compatible = "regulator-fixed";
+		vin-supply = <&reg_12v>;
+
+		gpio = <&gpioh 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-max-microvolt = <12000000>;
+		regulator-min-microvolt = <12000000>;
+		regulator-name = "12V_IOBUS";
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "STACK_CS2", "", "STACK_CS3", /*  0 */
+	"ETH_GPIO1", "ETH_INT", "", "", "",                     /*  5 */
+	"", "", "", "BOOTROM_LED", "ETH_LAB_LEDRP",             /* 10 */
+	"";                                                     /* 15 */
+};
+
+&gpioc {
+	gpio-line-names = "", "STACK_CS1", "", "", "", /*  0 */
+	"", "", "", "", "",                            /*  5 */
+	"", "";                                        /* 10 */
+};
+
+&gpu {
+	status = "disabled";
+};
+
+&i2c1 {
+	powerboard_gpio: gpio@24 {
+		compatible = "nxp,pca9570";
+		reg = <0x24>;
+
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-line-names = "DUT_PWR_EN", "DUT_PWR_DISCH", "DUT_PWR_ADCRST", "";
+	};
+};
+
+&spi2 {
+	adc@0 {
+		compatible = "ti,lmp92064";
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		vdd-supply = <&reg_pb_3v3>;
+		vdig-supply = <&reg_pb_3v3>;
+		reset-gpios = <&powerboard_gpio 2 GPIO_ACTIVE_HIGH>;
+
+		shunt-resistor-micro-ohms = <15000>;
+	};
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	backlight_pwm: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm1_pins_c>;
+		pinctrl-1 = <&pwm1_sleep_pins_c>;
+
+		status = "okay";
+	};
+};

arch/arm/boot/dts/st/stm32mp157c-lxa-tac-gen2.dts

+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ * Copyright (C) 2023 Leonard Göhrs, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc-lxa-tac.dtsi"
+
+/ {
+	model = "Linux Automation Test Automation Controller (TAC) Gen 2";
+	compatible = "lxa,stm32mp157c-tac-gen2", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&v3v3>;
+
+		brightness-levels = <0 31 63 95 127 159 191 223 255>;
+		default-brightness-level = <7>;
+		pwms = <&led_pwm 3 1000000 0>;
+	};
+
+	reg_iobus_12v: regulator-iobus-12v {
+		compatible = "regulator-fixed";
+		vin-supply = <&reg_12v>;
+		gpio = <&gpioh 13 GPIO_ACTIVE_LOW>;
+		regulator-max-microvolt = <12000000>;
+		regulator-min-microvolt = <12000000>;
+		regulator-name = "12V_IOBUS";
+	};
+
+	led-controller-1 {
+		compatible = "pwm-leds-multicolor";
+
+		multi-led {
+			color = <LED_COLOR_ID_RGB>;
+			function = LED_FUNCTION_STATUS;
+			max-brightness = <65535>;
+
+			led-red {
+				active-low;
+				color = <LED_COLOR_ID_RED>;
+				pwms = <&led_pwm 0 1000000 0>;
+			};
+
+			led-green {
+				active-low;
+				color = <LED_COLOR_ID_GREEN>;
+				pwms = <&led_pwm 2 1000000 0>;
+			};
+
+			led-blue {
+				active-low;
+				color = <LED_COLOR_ID_BLUE>;
+				pwms = <&led_pwm 1 1000000 0>;
+			};
+		};
+	};
+
+	led-controller-2 {
+		compatible = "gpio-leds";
+
+		led-5 {
+			label = "tac:green:iobus";
+			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-6 {
+			label = "tac:green:can";
+			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-7 {
+			label = "tac:green:out0";
+			gpios = <&gpiob 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-8 {
+			label = "tac:green:out1";
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-9 {
+			label = "tac:green:uarttx";
+			gpios = <&gpiod 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-10 {
+			label = "tac:green:uartrx";
+			gpios = <&gpiof 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-11 {
+			label = "tac:green:usbh1";
+			gpios = <&gpioc 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-12 {
+			label = "tac:green:usbh2";
+			gpios = <&gpiod 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-13 {
+			label = "tac:green:usbh3";
+			gpios = <&gpiob 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-14 {
+			label = "tac:green:usbg";
+			gpios = <&gpiod 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usb-gadget";
+		};
+
+		led-15 {
+			label = "tac:green:dutpwr";
+			gpios = <&gpioa 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "DUT_PWR_EN", "", "STACK_CS3", /*  0 */
+	"ETH_GPIO1", "ETH_INT", "", "", "",                      /*  5 */
+	"", "", "", "BOOTROM_LED", "ETH_LAB_LEDRP",              /* 10 */
+	"";                                                      /* 15 */
+};
+
+&gpioc {
+	gpio-line-names = "", "DUT_PWR_DISCH", "", "", "", /*  0 */
+	"", "", "", "", "",                                /*  5 */
+	"", "";                                            /* 10 */
+};
+
+&gpu {
+	status = "disabled";
+};
+
+&m_can2 {
+	termination-gpios = <&gpioe 4 GPIO_ACTIVE_HIGH>;
+	termination-ohms = <120>;
+};
+
+&spi2 {
+	adc@0 {
+		compatible = "ti,lmp92064";
+		reg = <0>;
+
+		reset-gpios = <&gpioa 4 GPIO_ACTIVE_HIGH>;
+		shunt-resistor-micro-ohms = <15000>;
+		spi-max-frequency = <5000000>;
+		vdd-supply = <&reg_pb_3v3>;
+		vdig-supply = <&reg_pb_3v3>;
+	};
+};
+
+&timers8 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	status = "okay";
+
+	led_pwm: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm8_pins_b>;
+		pinctrl-1 = <&pwm8_sleep_pins_b>;
+		status = "okay";
+	};
+};

arch/arm/boot/dts/st/stm32mp157c-odyssey-som.dtsi

@@ -230,8 +230,8 @@ &iwdg2 {
 &m4_rproc {
 	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
 			<&vdev0vring1>, <&vdev0buffer>;
-	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
-	mbox-names = "vq0", "vq1", "shutdown";
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
 	interrupt-parent = <&exti>;
 	interrupts = <68 1>;
 	status = "okay";

arch/arm/boot/dts/st/stm32mp15xx-dhcom-som.dtsi

@@ -416,8 +416,8 @@ &iwdg2 {
 &m4_rproc {
 	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
 			<&vdev0vring1>, <&vdev0buffer>;
-	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
-	mbox-names = "vq0", "vq1", "shutdown";
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
 	interrupt-parent = <&exti>;
 	interrupts = <68 1>;
 	status = "okay";

arch/arm/boot/dts/st/stm32mp15xx-dhcor-som.dtsi

@@ -227,8 +227,8 @@ &iwdg2 {
 &m4_rproc {
 	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
 			<&vdev0vring1>, <&vdev0buffer>;
-	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
-	mbox-names = "vq0", "vq1", "shutdown";
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
 	interrupt-parent = <&exti>;
 	interrupts = <68 1>;
 	status = "okay";

include/dt-bindings/regulator/st,stm32mp13-regulator.h

+/* SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) */
+/*
+ * Copyright (C) 2022, STMicroelectronics - All Rights Reserved
+ */
+
+#ifndef __DT_BINDINGS_REGULATOR_ST_STM32MP13_REGULATOR_H
+#define __DT_BINDINGS_REGULATOR_ST_STM32MP13_REGULATOR_H
+
+/* SCMI voltage domains identifiers */
+
+/* SOC Internal regulators */
+#define VOLTD_SCMI_REG11		0
+#define VOLTD_SCMI_REG18		1
+#define VOLTD_SCMI_USB33		2
+#define VOLTD_SCMI_SDMMC1_IO		3
+#define VOLTD_SCMI_SDMMC2_IO		4
+#define VOLTD_SCMI_VREFBUF		5
+
+/* STPMIC1 regulators */
+#define VOLTD_SCMI_STPMIC1_BUCK1	6
+#define VOLTD_SCMI_STPMIC1_BUCK2	7
+#define VOLTD_SCMI_STPMIC1_BUCK3	8
+#define VOLTD_SCMI_STPMIC1_BUCK4	9
+#define VOLTD_SCMI_STPMIC1_LDO1	        10
+#define VOLTD_SCMI_STPMIC1_LDO2	        11
+#define VOLTD_SCMI_STPMIC1_LDO3	        12
+#define VOLTD_SCMI_STPMIC1_LDO4	        13
+#define VOLTD_SCMI_STPMIC1_LDO5	        14
+#define VOLTD_SCMI_STPMIC1_LDO6	        15
+#define VOLTD_SCMI_STPMIC1_VREFDDR	16
+#define VOLTD_SCMI_STPMIC1_BOOST	17
+#define VOLTD_SCMI_STPMIC1_PWR_SW1	18
+#define VOLTD_SCMI_STPMIC1_PWR_SW2	19
+
+/* External regulators */
+#define VOLTD_SCMI_REGU0		20
+#define VOLTD_SCMI_REGU1		21
+#define VOLTD_SCMI_REGU2		22
+#define VOLTD_SCMI_REGU3		23
+#define VOLTD_SCMI_REGU4		24
+
+#endif /*__DT_BINDINGS_REGULATOR_ST_STM32MP13_REGULATOR_H */