Commit ac3e8ea1 authored by Masanari Iida's avatar Masanari Iida Committed by Jonathan Corbet

Documentation: devicetree: Fix double words in Doumentation/devicetree

This patch fix multiple words such as "the the" and "which which"
in Documentation/devicetree.
Signed-off-by: default avatarMasanari Iida <standby24x7@gmail.com>
Signed-off-by: default avatarJonathan Corbet <corbet@lwn.net>
parent 633708a4
......@@ -8,7 +8,7 @@ Properties:
"qcom,kpss-timer" - krait subsystem
"qcom,scss-timer" - scorpion subsystem
- interrupts : Interrupts for the the debug timer, the first general purpose
- interrupts : Interrupts for the debug timer, the first general purpose
timer, and optionally a second general purpose timer in that
order.
......
......@@ -9,7 +9,7 @@ Properties:
Compatibility with many Cavium evaluation boards.
- reg: The base address of the the CF chip select banks. Depending on
- reg: The base address of the CF chip select banks. Depending on
the device configuration, there may be one or two banks.
- cavium,bus-width: The width of the connection to the CF devices. Valid
......
......@@ -12,7 +12,7 @@ configuration register for writes. These configuration register may be used to
enable (and disable in some cases) SoC pin drivers, select peripheral clock
sources (internal or pin), etc. In some cases, a configuration register is
write once or the individual bits are write once. In addition to device config,
the DSCR block may provide registers which which are used to reset peripherals,
the DSCR block may provide registers which are used to reset peripherals,
provide device ID information, provide ethernet MAC addresses, as well as other
miscellaneous functions.
......
* Renesas R-Car DMA Controller Device Tree bindings
Renesas R-Car Generation 2 SoCs have have multiple multi-channel DMA
Renesas R-Car Generation 2 SoCs have multiple multi-channel DMA
controller instances named DMAC capable of serving multiple clients. Channels
can be dedicated to specific clients or shared between a large number of
clients.
......
......@@ -39,7 +39,7 @@ Optional Properties:
- lines-initial-states: Bitmask that specifies the initial state of each
line. When a bit is set to zero, the corresponding line will be initialized to
the input (pulled-up) state. When the bit is set to one, the line will be
initialized the the low-level output state. If the property is not specified
initialized the low-level output state. If the property is not specified
all lines will be initialized to the input state.
The I/O expander can detect input state changes, and thus optionally act as
......
......@@ -59,7 +59,7 @@ Optional properties:
Each child node represents one channel and has the following
properties:
Required properties:
* reg: Pair of pins the the channel is connected to.
* reg: Pair of pins the channel is connected to.
0: VP/VN
1: VAUXP[0]/VAUXN[0]
2: VAUXP[1]/VAUXN[1]
......
......@@ -9,7 +9,7 @@ Required properties:
Optional properties:
- bank-width : Width (in bytes) of the device. If not present, the width
defaults to 1 byte
- nand-skip-bbtscan: Indicates the the BBT scanning should be skipped
- nand-skip-bbtscan: Indicates the BBT scanning should be skipped
- timings: array of 6 bytes for NAND timings. The meanings of these bytes
are:
byte 0 TCLR : CLE to RE delay in number of AHB clock cycles, only 4 bits
......
......@@ -3,7 +3,7 @@
Required properties:
- compatible: should be one of "brcm,systemport-v1.00" or "brcm,systemport"
- reg: address and length of the register set for the device.
- interrupts: interrupts for the device, first cell must be for the the rx
- interrupts: interrupts for the device, first cell must be for the rx
interrupts, and the second cell should be for the transmit queues. An
optional third interrupt cell for Wake-on-LAN can be specified
- local-mac-address: Ethernet MAC address (48 bits) of this adapter
......
......@@ -37,7 +37,7 @@ Required properties:
You specify supplies using the standard regulator bindings by including
a phandle the the relevant regulator. All specified supplies must be able
a phandle the relevant regulator. All specified supplies must be able
to report their voltage. The IO Voltage Domain for any non-specified
supplies will be not be touched.
......
......@@ -10,7 +10,7 @@ How overlays work
-----------------
A Device Tree's overlay purpose is to modify the kernel's live tree, and
have the modification affecting the state of the the kernel in a way that
have the modification affecting the state of the kernel in a way that
is reflecting the changes.
Since the kernel mainly deals with devices, any new device node that result
in an active device should have it created while if the device node is either
......@@ -80,7 +80,7 @@ result in foo+bar.dts
};
---- foo+bar.dts -------------------------------------------------------------
As a result of the the overlay, a new device node (bar) has been created
As a result of the overlay, a new device node (bar) has been created
so a bar platform device will be registered and if a matching device driver
is loaded the device will be created as expected.
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment