wireless: indent kernel-doc with tabs

Almost everywhere tabs are used to indent continuation
lines, replace the few places that use spaces.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>

include/net/cfg80211.h

@@ -490,7 +490,7 @@ enum survey_info_flags {
  * @channel: the channel this survey record reports, mandatory
  * @filled: bitflag of flags from &enum survey_info_flags
  * @noise: channel noise in dBm. This and all following fields are
- *     optional
+ *	optional
  * @channel_time: amount of time in ms the radio spent on the channel
  * @channel_time_busy: amount of time the primary channel was sensed busy
  * @channel_time_ext_busy: amount of time the extension channel was sensed busy
@@ -546,9 +546,9 @@ struct cfg80211_crypto_settings {
 /**
  * struct cfg80211_beacon_data - beacon data
  * @head: head portion of beacon (before TIM IE)
- *     or %NULL if not changed
+ *	or %NULL if not changed
  * @tail: tail portion of beacon (after TIM IE)
- *     or %NULL if not changed
+ *	or %NULL if not changed
  * @head_len: length of @head
  * @tail_len: length of @tail
  * @beacon_ies: extra information element(s) to add into Beacon frames or %NULL
@@ -764,7 +764,7 @@ int cfg80211_check_station_change(struct wiphy *wiphy,
  * @STATION_INFO_PLINK_STATE: @plink_state filled
  * @STATION_INFO_SIGNAL: @signal filled
  * @STATION_INFO_TX_BITRATE: @txrate fields are filled
- *  (tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
+ *	(tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
  * @STATION_INFO_RX_PACKETS: @rx_packets filled with 32-bit value
  * @STATION_INFO_TX_PACKETS: @tx_packets filled with 32-bit value
  * @STATION_INFO_TX_RETRIES: @tx_retries filled
@@ -1509,7 +1509,7 @@ enum cfg80211_assoc_req_flags {
  * @prev_bssid: previous BSSID, if not %NULL use reassociate frame
  * @flags:  See &enum cfg80211_assoc_req_flags
  * @ht_capa:  HT Capabilities over-rides.  Values set in ht_capa_mask
- *   will be used in ht_capa.  Un-supported values will be ignored.
+ *	will be used in ht_capa.  Un-supported values will be ignored.
  * @ht_capa_mask:  The bits of ht_capa which are to be used.
  * @vht_capa: VHT capability override
  * @vht_capa_mask: VHT capability mask indicating which fields to use
@@ -1593,7 +1593,7 @@ struct cfg80211_disassoc_request {
  * @basic_rates: bitmap of basic rates to use when creating the IBSS
  * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
  * @ht_capa:  HT Capabilities over-rides.  Values set in ht_capa_mask
- *   will be used in ht_capa.  Un-supported values will be ignored.
+ *	will be used in ht_capa.  Un-supported values will be ignored.
  * @ht_capa_mask:  The bits of ht_capa which are to be used.
  */
 struct cfg80211_ibss_params {
@@ -1635,9 +1635,9 @@ struct cfg80211_ibss_params {
  * @key: WEP key for shared key authentication
  * @flags:  See &enum cfg80211_assoc_req_flags
  * @bg_scan_period:  Background scan period in seconds
- *   or -1 to indicate that default value is to be used.
+ *	or -1 to indicate that default value is to be used.
  * @ht_capa:  HT Capabilities over-rides.  Values set in ht_capa_mask
- *   will be used in ht_capa.  Un-supported values will be ignored.
+ *	will be used in ht_capa.  Un-supported values will be ignored.
  * @ht_capa_mask:  The bits of ht_capa which are to be used.
  * @vht_capa:  VHT Capability overrides
  * @vht_capa_mask: The bits of vht_capa which are to be used.

include/net/mac80211.h

@@ -1004,11 +1004,11 @@ enum ieee80211_smps_mode {
  * @radar_enabled: whether radar detection is enabled
  *
  * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
- *    (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
- *    but actually means the number of transmissions not the number of retries
+ *	(a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
+ *	but actually means the number of transmissions not the number of retries
  * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
- *    frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
- *    number of transmissions not the number of retries
+ *	frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
+ *	number of transmissions not the number of retries
  *
  * @smps_mode: spatial multiplexing powersave mode; note that
  *	%IEEE80211_SMPS_STATIC is used when the device is not
@@ -1092,7 +1092,7 @@ enum ieee80211_vif_flags {
  *	be off when it is %NULL there can still be races and packets could be
  *	processed after it switches back to %NULL.
  * @debugfs_dir: debugfs dentry, can be used by drivers to create own per
- *      interface debug files. Note that it will be NULL for the virtual
+ *	interface debug files. Note that it will be NULL for the virtual
  *	monitor interface (if that is requested.)
  * @drv_priv: data area for driver use, will always be aligned to
  *	sizeof(void *).
@@ -1425,10 +1425,10 @@ struct ieee80211_tx_control {
  *	the stack.
  *
  * @IEEE80211_HW_CONNECTION_MONITOR:
- *      The hardware performs its own connection monitoring, including
- *      periodic keep-alives to the AP and probing the AP on beacon loss.
- *      When this flag is set, signaling beacon-loss will cause an immediate
- *      change to disassociated state.
+ *	The hardware performs its own connection monitoring, including
+ *	periodic keep-alives to the AP and probing the AP on beacon loss.
+ *	When this flag is set, signaling beacon-loss will cause an immediate
+ *	change to disassociated state.
  *
  * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
  *	This device needs to get data from beacon before association (i.e.
@@ -1526,10 +1526,10 @@ enum ieee80211_hw_flags {
  * @channel_change_time: time (in microseconds) it takes to change channels.
  *
  * @max_signal: Maximum value for signal (rssi) in RX information, used
- *     only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
+ *	only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
  *
  * @max_listen_interval: max listen interval in units of beacon interval
- *     that HW supports
+ *	that HW supports
  *
  * @queues: number of available hardware transmit queues for
  *	data packets. WMM/QoS requires at least four, these
@@ -2443,7 +2443,7 @@ enum ieee80211_roc_type {
  *	The callback can sleep.
  *
  * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
- *      Currently, this is only used for IBSS mode debugging. Is not a
+ *	Currently, this is only used for IBSS mode debugging. Is not a
  *	required function.
  *	The callback can sleep.
  *