[media] gspca_pac73xx: Remove comments from before the 7302 / 7311 separation

The pac7302 and pac7311 driver still contains some comments from before
they were separated, such as marking certain functions 7302 or 7311 only,
with the new split drivers these make no sense, remove them.

Also removed the empty/unused sd_stop0 function from pac7311.c
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/video/gspca/pac7302.c

@@ -89,7 +89,6 @@ enum e_ctrl {
 	NCTRLS		/* number of controls */
 };
 
-/* specific webcam descriptor for pac7302 */
 struct sd {
 	struct gspca_dev gspca_dev;		/* !! must be the first item */
 
@@ -270,7 +269,6 @@ static const struct v4l2_pix_format vga_mode[] = {
 #define LOAD_PAGE3		255
 #define END_OF_SEQUENCE		0
 
-/* pac 7302 */
 static const u8 init_7302[] = {
 /*	index,value */
 	0xff, 0x01,		/* page 1 */
@@ -509,7 +507,6 @@ static int sd_config(struct gspca_dev *gspca_dev,
 	return 0;
 }
 
-/* This function is used by pac7302 only */
 static void setbrightcont(struct gspca_dev *gspca_dev)
 {
 	struct sd *sd = (struct sd *) gspca_dev;
@@ -536,7 +533,6 @@ static void setbrightcont(struct gspca_dev *gspca_dev)
 	reg_w(gspca_dev, 0xdc, 0x01);
 }
 
-/* This function is used by pac7302 only */
 static void setcolors(struct gspca_dev *gspca_dev)
 {
 	struct sd *sd = (struct sd *) gspca_dev;
@@ -700,8 +696,6 @@ static int sd_start(struct gspca_dev *gspca_dev)
 	setautogain(gspca_dev);
 	sethvflip(gspca_dev);
 
-	/* only resolution 640x480 is supported for pac7302 */
-
 	sd->sof_read = 0;
 	atomic_set(&sd->avg_lum, 270 + sd->ctrls[BRIGHTNESS].val);
 

drivers/media/video/gspca/pac7311.c

@@ -20,31 +20,26 @@
  */
 
 /* Some documentation about various registers as determined by trial and error.
-   When the register addresses differ between the 7202 and the 7311 the 2
-   different addresses are written as 7302addr/7311addr, when one of the 2
-   addresses is a - sign that register description is not valid for the
-   matching IC.
 
    Register page 1:
 
    Address	Description
-   -/0x08	Unknown compressor related, must always be 8 except when not
+   0x08		Unknown compressor related, must always be 8 except when not
 		in 640x480 resolution and page 4 reg 2 <= 3 then set it to 9 !
-   -/0x1b	Auto white balance related, bit 0 is AWB enable (inverted)
+   0x1b		Auto white balance related, bit 0 is AWB enable (inverted)
 		bits 345 seem to toggle per color gains on/off (inverted)
    0x78		Global control, bit 6 controls the LED (inverted)
-   -/0x80	JPEG compression ratio ? Best not touched
+   0x80		JPEG compression ratio ? Best not touched
 
-   Register page 3/4:
+   Register page 4:
 
    Address	Description
    0x02		Clock divider 2-63, fps =~ 60 / val. Must be a multiple of 3 on
 		the 7302, so one of 3, 6, 9, ..., except when between 6 and 12?
-   -/0x0f	Master gain 1-245, low value = high gain
-   0x10/-	Master gain 0-31
-   -/0x10	Another gain 0-15, limited influence (1-2x gain I guess)
+   0x0f		Master gain 1-245, low value = high gain
+   0x10		Another gain 0-15, limited influence (1-2x gain I guess)
    0x21		Bitfield: 0-1 unused, 2-3 vflip/hflip, 4-5 unknown, 6-7 unused
-   -/0x27	Seems to toggle various gains on / off, Setting bit 7 seems to
+   0x27		Seems to toggle various gains on / off, Setting bit 7 seems to
 		completely disable the analog amplification block. Set to 0x68
 		for max gain, 0x14 for minimal gain.
 */
@@ -60,7 +55,6 @@ MODULE_AUTHOR("Thomas Kaiser thomas@kaiser-linux.li");
 MODULE_DESCRIPTION("Pixart PAC7311");
 MODULE_LICENSE("GPL");
 
-/* specific webcam descriptor for pac7311 */
 struct sd {
 	struct gspca_dev gspca_dev;		/* !! must be the first item */
 
@@ -92,7 +86,6 @@ static int sd_setexposure(struct gspca_dev *gspca_dev, __s32 val);
 static int sd_getexposure(struct gspca_dev *gspca_dev, __s32 *val);
 
 static const struct ctrl sd_ctrls[] = {
-/* This control is for both the 7302 and the 7311 */
 	{
 	    {
 		.id      = V4L2_CID_CONTRAST,
@@ -108,7 +101,6 @@ static const struct ctrl sd_ctrls[] = {
 	    .set = sd_setcontrast,
 	    .get = sd_getcontrast,
 	},
-/* All controls below are for both the 7302 and the 7311 */
 	{
 	    {
 		.id      = V4L2_CID_GAIN,
@@ -206,7 +198,6 @@ static const struct v4l2_pix_format vga_mode[] = {
 #define LOAD_PAGE4		254
 #define END_OF_SEQUENCE		0
 
-/* pac 7311 */
 static const __u8 init_7311[] = {
 	0x78, 0x40,	/* Bit_0=start stream, Bit_6=LED */
 	0x78, 0x40,	/* Bit_0=start stream, Bit_6=LED */
@@ -392,7 +383,6 @@ static int sd_config(struct gspca_dev *gspca_dev,
 
 	cam = &gspca_dev->cam;
 
-	PDEBUG(D_CONF, "Find Sensor PAC7311");
 	cam->cam_mode = vga_mode;
 	cam->nmodes = ARRAY_SIZE(vga_mode);
 
@@ -405,7 +395,6 @@ static int sd_config(struct gspca_dev *gspca_dev,
 	return 0;
 }
 
-/* This function is used by pac7311 only */
 static void setcontrast(struct gspca_dev *gspca_dev)
 {
 	struct sd *sd = (struct sd *) gspca_dev;
@@ -438,7 +427,7 @@ static void setexposure(struct gspca_dev *gspca_dev)
 	struct sd *sd = (struct sd *) gspca_dev;
 	__u8 reg;
 
-	/* register 2 of frame 3/4 contains the clock divider configuring the
+	/* register 2 of page 4 contains the clock divider configuring the
 	   no fps according to the formula: 60 / reg. sd->exposure is the
 	   desired exposure time in ms. */
 	reg = 120 * sd->exposure / 1000;
@@ -451,7 +440,7 @@ static void setexposure(struct gspca_dev *gspca_dev)
 	reg_w(gspca_dev, 0x02, reg);
 
 	/* Page 1 register 8 must always be 0x08 except when not in
-	   640x480 mode and Page3/4 reg 2 <= 3 then it must be 9 */
+	   640x480 mode and page 4 reg 2 <= 3 then it must be 9 */
 	reg_w(gspca_dev, 0xff, 0x01);
 	if (gspca_dev->cam.cam_mode[(int)gspca_dev->curr_mode].priv &&
 			reg <= 3) {
@@ -499,12 +488,12 @@ static int sd_start(struct gspca_dev *gspca_dev)
 
 	/* set correct resolution */
 	switch (gspca_dev->cam.cam_mode[(int) gspca_dev->curr_mode].priv) {
-	case 2:					/* 160x120 pac7311 */
+	case 2:					/* 160x120 */
 		reg_w(gspca_dev, 0xff, 0x01);
 		reg_w(gspca_dev, 0x17, 0x20);
 		reg_w(gspca_dev, 0x87, 0x10);
 		break;
-	case 1:					/* 320x240 pac7311 */
+	case 1:					/* 320x240 */
 		reg_w(gspca_dev, 0xff, 0x01);
 		reg_w(gspca_dev, 0x17, 0x30);
 		reg_w(gspca_dev, 0x87, 0x11);
@@ -541,11 +530,6 @@ static void sd_stopN(struct gspca_dev *gspca_dev)
 	reg_w(gspca_dev, 0x78, 0x44); /* Bit_0=start stream, Bit_6=LED */
 }
 
-/* called on streamoff with alt 0 and on disconnect for 7311 */
-static void sd_stop0(struct gspca_dev *gspca_dev)
-{
-}
-
 /* Include pac common sof detection functions */
 #include "pac_common.h"
 
@@ -820,7 +804,6 @@ static int sd_int_pkt_scan(struct gspca_dev *gspca_dev,
 }
 #endif
 
-/* sub-driver description for pac7311 */
 static const struct sd_desc sd_desc = {
 	.name = MODULE_NAME,
 	.ctrls = sd_ctrls,
@@ -829,7 +812,6 @@ static const struct sd_desc sd_desc = {
 	.init = sd_init,
 	.start = sd_start,
 	.stopN = sd_stopN,
-	.stop0 = sd_stop0,
 	.pkt_scan = sd_pkt_scan,
 	.dq_callback = do_autogain,
 #if defined(CONFIG_INPUT) || defined(CONFIG_INPUT_MODULE)