Commit b1044a9b authored by Linus Torvalds's avatar Linus Torvalds

Revert drm/vc4 hdmi runtime PM changes

This reverts commits

  9984d666 ("drm/vc4: hdmi: Make sure the controller is powered in detect")
  411efa18 ("drm/vc4: hdmi: Move the HSM clock enable to runtime_pm")

as Michael Stapelberg reports that the new runtime PM changes cause his
Raspberry Pi 3 to hang on boot, probably due to interactions with other
changes in the DRM tree (because a bisect points to the merge in commit
e058a84b: "Merge tag 'drm-next-2021-07-01' of git://.../drm").

Revert these two commits until it's been resolved.

Link: https://lore.kernel.org/all/871r5mp7h2.fsf@midna.i-did-not-set--mail-host-address--so-tickle-me/Reported-and-tested-by: default avatarMichael Stapelberg <michael@stapelberg.ch>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent d4d016ca
......@@ -167,8 +167,6 @@ vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
struct vc4_hdmi *vc4_hdmi = connector_to_vc4_hdmi(connector);
bool connected = false;
WARN_ON(pm_runtime_resume_and_get(&vc4_hdmi->pdev->dev));
if (vc4_hdmi->hpd_gpio &&
gpiod_get_value_cansleep(vc4_hdmi->hpd_gpio)) {
connected = true;
......@@ -189,12 +187,10 @@ vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)
}
}
pm_runtime_put(&vc4_hdmi->pdev->dev);
return connector_status_connected;
}
cec_phys_addr_invalidate(vc4_hdmi->cec_adap);
pm_runtime_put(&vc4_hdmi->pdev->dev);
return connector_status_disconnected;
}
......@@ -635,6 +631,7 @@ static void vc4_hdmi_encoder_post_crtc_powerdown(struct drm_encoder *encoder,
vc4_hdmi->variant->phy_disable(vc4_hdmi);
clk_disable_unprepare(vc4_hdmi->pixel_bvb_clock);
clk_disable_unprepare(vc4_hdmi->hsm_clock);
clk_disable_unprepare(vc4_hdmi->pixel_clock);
ret = pm_runtime_put(&vc4_hdmi->pdev->dev);
......@@ -947,6 +944,13 @@ static void vc4_hdmi_encoder_pre_crtc_configure(struct drm_encoder *encoder,
return;
}
ret = clk_prepare_enable(vc4_hdmi->hsm_clock);
if (ret) {
DRM_ERROR("Failed to turn on HSM clock: %d\n", ret);
clk_disable_unprepare(vc4_hdmi->pixel_clock);
return;
}
vc4_hdmi_cec_update_clk_div(vc4_hdmi);
if (pixel_rate > 297000000)
......@@ -959,6 +963,7 @@ static void vc4_hdmi_encoder_pre_crtc_configure(struct drm_encoder *encoder,
ret = clk_set_min_rate(vc4_hdmi->pixel_bvb_clock, bvb_rate);
if (ret) {
DRM_ERROR("Failed to set pixel bvb clock rate: %d\n", ret);
clk_disable_unprepare(vc4_hdmi->hsm_clock);
clk_disable_unprepare(vc4_hdmi->pixel_clock);
return;
}
......@@ -966,6 +971,7 @@ static void vc4_hdmi_encoder_pre_crtc_configure(struct drm_encoder *encoder,
ret = clk_prepare_enable(vc4_hdmi->pixel_bvb_clock);
if (ret) {
DRM_ERROR("Failed to turn on pixel bvb clock: %d\n", ret);
clk_disable_unprepare(vc4_hdmi->hsm_clock);
clk_disable_unprepare(vc4_hdmi->pixel_clock);
return;
}
......@@ -2114,29 +2120,6 @@ static int vc5_hdmi_init_resources(struct vc4_hdmi *vc4_hdmi)
return 0;
}
#ifdef CONFIG_PM
static int vc4_hdmi_runtime_suspend(struct device *dev)
{
struct vc4_hdmi *vc4_hdmi = dev_get_drvdata(dev);
clk_disable_unprepare(vc4_hdmi->hsm_clock);
return 0;
}
static int vc4_hdmi_runtime_resume(struct device *dev)
{
struct vc4_hdmi *vc4_hdmi = dev_get_drvdata(dev);
int ret;
ret = clk_prepare_enable(vc4_hdmi->hsm_clock);
if (ret)
return ret;
return 0;
}
#endif
static int vc4_hdmi_bind(struct device *dev, struct device *master, void *data)
{
const struct vc4_hdmi_variant *variant = of_device_get_match_data(dev);
......@@ -2391,18 +2374,11 @@ static const struct of_device_id vc4_hdmi_dt_match[] = {
{}
};
static const struct dev_pm_ops vc4_hdmi_pm_ops = {
SET_RUNTIME_PM_OPS(vc4_hdmi_runtime_suspend,
vc4_hdmi_runtime_resume,
NULL)
};
struct platform_driver vc4_hdmi_driver = {
.probe = vc4_hdmi_dev_probe,
.remove = vc4_hdmi_dev_remove,
.driver = {
.name = "vc4_hdmi",
.of_match_table = vc4_hdmi_dt_match,
.pm = &vc4_hdmi_pm_ops,
},
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment