scsi: ufs: Add a quirk to permit overriding UniPro defaults

The UniPro specification states that attribute IDs of the following
parameters are vendor-specific so some SoCs could have no regions at the
defined addresses:

 - DME_LocalFC0ProtectionTimeOutVal
 - DME_LocalTC0ReplayTimeOutVal
 - DME_LocalAFC0ReqTimeOutVal

In addition, the following parameters should be set considering the
compatibility between host and device.

 - PA_PWRMODEUSERDATA0
 - PA_PWRMODEUSERDATA1
 - PA_PWRMODEUSERDATA2
 - PA_PWRMODEUSERDATA3
 - PA_PWRMODEUSERDATA4
 - PA_PWRMODEUSERDATA5

Introduce a quirk to allow vendor drivers to override the UniPro defaults.

Link: https://lore.kernel.org/r/1fedd3dea0ccc980913a5995a10510d86a5b01b9.1608513782.git.kwmad.kim@samsung.comAcked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

drivers/scsi/ufs/ufshcd.c

@@ -4215,25 +4215,27 @@ static int ufshcd_change_power_mode(struct ufs_hba *hba,
 		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_HSSERIES),
 						pwr_mode->hs_rate);
 
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA0),
-			DL_FC0ProtectionTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA1),
-			DL_TC0ReplayTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA2),
-			DL_AFC0ReqTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA3),
-			DL_FC1ProtectionTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA4),
-			DL_TC1ReplayTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA5),
-			DL_AFC1ReqTimeOutVal_Default);
-
-	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalFC0ProtectionTimeOutVal),
-			DL_FC0ProtectionTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalTC0ReplayTimeOutVal),
-			DL_TC0ReplayTimeOutVal_Default);
-	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalAFC0ReqTimeOutVal),
-			DL_AFC0ReqTimeOutVal_Default);
+	if (!(hba->quirks & UFSHCD_QUIRK_SKIP_DEF_UNIPRO_TIMEOUT_SETTING)) {
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA0),
+				DL_FC0ProtectionTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA1),
+				DL_TC0ReplayTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA2),
+				DL_AFC0ReqTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA3),
+				DL_FC1ProtectionTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA4),
+				DL_TC1ReplayTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA5),
+				DL_AFC1ReqTimeOutVal_Default);
+
+		ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalFC0ProtectionTimeOutVal),
+				DL_FC0ProtectionTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalTC0ReplayTimeOutVal),
+				DL_TC0ReplayTimeOutVal_Default);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalAFC0ReqTimeOutVal),
+				DL_AFC0ReqTimeOutVal_Default);
+	}
 
 	ret = ufshcd_uic_change_pwr_mode(hba, pwr_mode->pwr_rx << 4
 			| pwr_mode->pwr_tx);

drivers/scsi/ufs/ufshcd.h

@@ -551,6 +551,12 @@ enum ufshcd_quirks {
 	 */
 	UFSHCI_QUIRK_SKIP_MANUAL_WB_FLUSH_CTRL		= 1 << 12,
 
+	/*
+	 * This quirk needs to disable unipro timeout values
+	 * before power mode change
+	 */
+	UFSHCD_QUIRK_SKIP_DEF_UNIPRO_TIMEOUT_SETTING = 1 << 13,
+
 };
 
 enum ufshcd_caps {