Merge tag 'spi-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "One new core feature here, a small collection of new drivers and a
  bunch of small improvements in existing drivers:

   - A new CS_WORD flag for transfers where the chip select is toggled
     at every word, with both a generic implementation and the ability
     for controllers to do this automatically (including a DaVinci one).

   - New drivers for Mediatek MT2712, Qualcomm GENI and QSPI, Spreadtrum
     SPI and ST STM32 QSPI plus new IDs for several existing ones"

* tag 'spi-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (86 commits)
  spi: lpspi: add imx8qxp compatible string
  spi: Allow building SPI_BCM63XX_HSSPI on ARM-based SoCs
  spi: omap2-mcspi: Add slave mode support
  spi: omap2-mcspi: Set FIFO DMA trigger level to word length
  spi: omap2-mcspi: Switch to readl_poll_timeout()
  spi: spi-mem: add stm32 qspi controller
  dt-bindings: spi: add stm32 qspi controller
  spi: sh-msiof: document R8A779{7|8}0 bindings
  spi: pic32-sqi: don't pass GFP_DMA32 to dma_alloc_coherent
  MAINTAINERS: Add entry for Broadcom SPI controller
  spi: sh-msiof: fix deferred probing
  spi: imx: use PIO mode if size is small
  spi: imx: correct wml as the last sg length
  spi: imx: move wml setting to later than setup_transfer
  PCI: Provide pci_match_id() with CONFIG_PCI=n
  spi: Make GPIO CSs honour the SPI_NO_CS flag
  spi/spi-pxa2xx: add PXA2xx SSP SPI Controller
  spi: pxa2xx: Add devicetree support
  spi: pxa2xx: Use an enum for type
  spi: spi-geni-qcom: Add SPI driver support for GENI based QUP
  ...

Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt

@@ -53,20 +53,8 @@ Required properties:
 - clocks:		Serial engine core clock needed by the device.
 
 Qualcomm Technologies Inc. GENI Serial Engine based SPI Controller
-
-Required properties:
-- compatible:		Must contain "qcom,geni-spi".
-- reg:			Must contain SPI register location and length.
-- interrupts:		Must contain SPI controller interrupts.
-- clock-names:		Must contain "se".
-- clocks:		Serial engine core clock needed by the device.
-- spi-max-frequency:	Specifies maximum SPI clock frequency, units - Hz.
-- #address-cells:	Must be <1> to define a chip select address on
-			the SPI bus.
-- #size-cells:		Must be <0>.
-
-SPI slave nodes must be children of the SPI master node and conform to SPI bus
-binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt.
+node binding is described in
+Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt.
 
 Example:
 	geniqup@8c0000 {
@@ -103,17 +91,4 @@ Example:
 			pinctrl-1 = <&qup_1_uart_3_sleep>;
 		};
 
-		spi0: spi@a84000 {
-			compatible = "qcom,geni-spi";
-			reg = <0xa84000 0x4000>;
-			interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
-			clock-names = "se";
-			clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
-			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&qup_1_spi_2_active>;
-			pinctrl-1 = <&qup_1_spi_2_sleep>;
-			spi-max-frequency = <19200000>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
 	}

Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt

+GENI based Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
+
+The QUP v3 core is a GENI based AHB slave that provides a common data path
+(an output FIFO and an input FIFO) for serial peripheral interface (SPI)
+mini-core.
+
+SPI in master mode supports up to 50MHz, up to four chip selects, programmable
+data path from 4 bits to 32 bits and numerous protocol variants.
+
+Required properties:
+- compatible:		Must contain "qcom,geni-spi".
+- reg:			Must contain SPI register location and length.
+- interrupts:		Must contain SPI controller interrupts.
+- clock-names:		Must contain "se".
+- clocks:		Serial engine core clock needed by the device.
+- #address-cells:	Must be <1> to define a chip select address on
+			the SPI bus.
+- #size-cells:		Must be <0>.
+
+SPI Controller nodes must be child of GENI based Qualcomm Universal
+Peripharal. Please refer GENI based QUP wrapper controller node bindings
+described in Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt.
+
+SPI slave nodes must be children of the SPI master node and conform to SPI bus
+binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt.
+
+Example:
+	spi0: spi@a84000 {
+		compatible = "qcom,geni-spi";
+		reg = <0xa84000 0x4000>;
+		interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "se";
+		clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&qup_1_spi_2_active>;
+		pinctrl-1 = <&qup_1_spi_2_sleep>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};

Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.txt

+Qualcomm Quad Serial Peripheral Interface (QSPI)
+
+The QSPI controller allows SPI protocol communication in single, dual, or quad
+wire transmission modes for read/write access to slaves such as NOR flash.
+
+Required properties:
+- compatible:	An SoC specific identifier followed by "qcom,qspi-v1", such as
+		"qcom,sdm845-qspi", "qcom,qspi-v1"
+- reg:		Should contain the base register location and length.
+- interrupts:	Interrupt number used by the controller.
+- clocks:	Should contain the core and AHB clock.
+- clock-names:	Should be "core" for core clock and "iface" for AHB clock.
+
+SPI slave nodes must be children of the SPI master node and can contain
+properties described in Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+
+	qspi: spi@88df000 {
+		compatible = "qcom,sdm845-qspi", "qcom,qspi-v1";
+		reg = <0x88df000 0x600>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "iface", "core";
+		clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			 <&gcc GCC_QSPI_CORE_CLK>;
+
+		flash@0 {
+			compatible = "jedec,spi-nor";
+			reg = <0>;
+			spi-max-frequency = <25000000>;
+			spi-tx-bus-width = <2>;
+			spi-rx-bus-width = <2>;
+		};
+	};

Documentation/devicetree/bindings/spi/sh-msiof.txt

@@ -2,7 +2,9 @@ Renesas MSIOF spi controller
 
 Required properties:
 - compatible           : "renesas,msiof-r8a7743" (RZ/G1M)
+			 "renesas,msiof-r8a7744" (RZ/G1N)
 			 "renesas,msiof-r8a7745" (RZ/G1E)
+			 "renesas,msiof-r8a774a1" (RZ/G2M)
 			 "renesas,msiof-r8a7790" (R-Car H2)
 			 "renesas,msiof-r8a7791" (R-Car M2-W)
 			 "renesas,msiof-r8a7792" (R-Car V2H)
@@ -11,10 +13,14 @@ Required properties:
 			 "renesas,msiof-r8a7795" (R-Car H3)
 			 "renesas,msiof-r8a7796" (R-Car M3-W)
 			 "renesas,msiof-r8a77965" (R-Car M3-N)
+			 "renesas,msiof-r8a77970" (R-Car V3M)
+			 "renesas,msiof-r8a77980" (R-Car V3H)
+			 "renesas,msiof-r8a77990" (R-Car E3)
+			 "renesas,msiof-r8a77995" (R-Car D3)
 			 "renesas,msiof-sh73a0" (SH-Mobile AG5)
 			 "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device)
 			 "renesas,rcar-gen2-msiof" (generic R-Car Gen2 and RZ/G1 compatible device)
-			 "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device)
+			 "renesas,rcar-gen3-msiof" (generic R-Car Gen3 and RZ/G2 compatible device)
 			 "renesas,sh-msiof"      (deprecated)
 
 			 When compatible with the generic version, nodes

Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt

@@ -2,7 +2,7 @@ Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface.
 
 Required properties:
 - compatible : "snps,dw-apb-ssi" or "mscc,<soc>-spi", where soc is "ocelot" or
-  "jaguar2"
+  "jaguar2", or "amazon,alpine-dw-apb-ssi"
 - reg : The register base for the controller. For "mscc,<soc>-spi", a second
   register set is required (named ICPU_CFG:SPI_MST)
 - interrupts : One interrupt, used by the controller.

Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt

@@ -3,6 +3,7 @@
 Required properties:
 - compatible :
   - "fsl,imx7ulp-spi" for LPSPI compatible with the one integrated on i.MX7ULP soc
+  - "fsl,imx8qxp-spi" for LPSPI compatible with the one integrated on i.MX8QXP soc
 - reg : address and length of the lpspi master registers
 - interrupts : lpspi interrupt
 - clocks : lpspi clock specifier

Documentation/devicetree/bindings/spi/spi-pxa2xx.txt

+PXA2xx SSP SPI Controller
+
+Required properties:
+- compatible: Must be "marvell,mmp2-ssp".
+- reg: Offset and length of the device's register set.
+- interrupts: Should be the interrupt number.
+- clocks: Should contain a single entry describing the clock input.
+- #address-cells:  Number of cells required to define a chip select address.
+- #size-cells: Should be zero.
+
+Optional properties:
+- cs-gpios: list of GPIO chip selects. See the SPI bus bindings,
+  Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Child nodes represent devices on the SPI bus
+  See ../spi/spi-bus.txt
+
+Example:
+	ssp1: spi@d4035000 {
+		compatible = "marvell,mmp2-ssp";
+		reg = <0xd4035000 0x1000>;
+		clocks = <&soc_clocks MMP2_CLK_SSP0>;
+		interrupts = <0>;
+	};

Documentation/devicetree/bindings/spi/spi-rspi.txt

@@ -3,7 +3,7 @@ Device tree configuration for Renesas RSPI/QSPI driver
 Required properties:
 - compatible       : For Renesas Serial Peripheral Interface on legacy SH:
 		     "renesas,rspi-<soctype>", "renesas,rspi" as fallback.
-		     For Renesas Serial Peripheral Interface on RZ/A1H:
+		     For Renesas Serial Peripheral Interface on RZ/A:
 		     "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback.
 		     For Quad Serial Peripheral Interface on R-Car Gen2 and
 		     RZ/G1 devices:
@@ -11,7 +11,9 @@ Required properties:
 		     Examples with soctypes are:
 		        - "renesas,rspi-sh7757" (SH)
 			- "renesas,rspi-r7s72100" (RZ/A1H)
+			- "renesas,rspi-r7s9210" (RZ/A2)
 			- "renesas,qspi-r8a7743" (RZ/G1M)
+			- "renesas,qspi-r8a7744" (RZ/G1N)
 			- "renesas,qspi-r8a7745" (RZ/G1E)
 			- "renesas,qspi-r8a7790" (R-Car H2)
 			- "renesas,qspi-r8a7791" (R-Car M2-W)

Documentation/devicetree/bindings/spi/spi-slave-mt27xx.txt

+Binding for MTK SPI Slave controller
+
+Required properties:
+- compatible: should be one of the following.
+    - mediatek,mt2712-spi-slave: for mt2712 platforms
+- reg: Address and length of the register set for the device.
+- interrupts: Should contain spi interrupt.
+- clocks: phandles to input clocks.
+  It's clock gate, and should be <&infracfg CLK_INFRA_AO_SPI1>.
+- clock-names: should be "spi" for the clock gate.
+
+Optional properties:
+- assigned-clocks: it's mux clock, should be <&topckgen CLK_TOP_SPISLV_SEL>.
+- assigned-clock-parents: parent of mux clock.
+  It's PLL, and should be one of the following.
+   -  <&topckgen CLK_TOP_UNIVPLL1_D2>: specify parent clock 312MHZ.
+				       It's the default one.
+   -  <&topckgen CLK_TOP_UNIVPLL1_D4>: specify parent clock 156MHZ.
+   -  <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ.
+   -  <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ.
+
+Example:
+- SoC Specific Portion:
+spis1: spi@10013000 {
+	compatible = "mediatek,mt2712-spi-slave";
+	reg = <0 0x10013000 0 0x100>;
+	interrupts = <GIC_SPI 283 IRQ_TYPE_LEVEL_LOW>;
+	clocks = <&infracfg CLK_INFRA_AO_SPI1>;
+	clock-names = "spi";
+	assigned-clocks = <&topckgen CLK_TOP_SPISLV_SEL>;
+	assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL1_D2>;
+};

Documentation/devicetree/bindings/spi/spi-sprd.txt

+Spreadtrum SPI Controller
+
+Required properties:
+- compatible: Should be "sprd,sc9860-spi".
+- reg: Offset and length of SPI controller register space.
+- interrupts: Should contain SPI interrupt.
+- clock-names: Should contain following entries:
+	"spi" for SPI clock,
+	"source" for SPI source (parent) clock,
+	"enable" for SPI module enable clock.
+- clocks: List of clock input name strings sorted in the same order
+	as the clock-names property.
+- #address-cells: The number of cells required to define a chip select
+	address on the SPI bus. Should be set to 1.
+- #size-cells: Should be set to 0.
+
+Example:
+spi0: spi@70a00000{
+	compatible = "sprd,sc9860-spi";
+	reg = <0 0x70a00000 0 0x1000>;
+	interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	clock-names = "spi", "source","enable";
+	clocks = <&clk_spi0>, <&ext_26m>, <&clk_ap_apb_gates 5>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};

Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt

+* STMicroelectronics Quad Serial Peripheral Interface(QSPI)
+
+Required properties:
+- compatible: should be "st,stm32f469-qspi"
+- reg: the first contains the register location and length.
+       the second contains the memory mapping address and length
+- reg-names: should contain the reg names "qspi" "qspi_mm"
+- interrupts: should contain the interrupt for the device
+- clocks: the phandle of the clock needed by the QSPI controller
+- A pinctrl must be defined to set pins in mode of operation for QSPI transfer
+
+Optional properties:
+- resets: must contain the phandle to the reset controller.
+
+A spi flash (NOR/NAND) must be a child of spi node and could have some
+properties. Also see jedec,spi-nor.txt.
+
+Required properties:
+- reg: chip-Select number (QSPI controller may connect 2 flashes)
+- spi-max-frequency: max frequency of spi bus
+
+Optional property:
+- spi-rx-bus-width: see ./spi-bus.txt for the description
+
+Example:
+
+qspi: spi@a0001000 {
+	compatible = "st,stm32f469-qspi";
+	reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>;
+	reg-names = "qspi", "qspi_mm";
+	interrupts = <91>;
+	resets = <&rcc STM32F4_AHB3_RESET(QSPI)>;
+	clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi0>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		...
+	};
+};

MAINTAINERS

@@ -3121,6 +3121,15 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.txt
 F:	drivers/memory/brcmstb_dpfe.c
 
+BROADCOM SPI DRIVER
+M:	Kamal Dasu <kdasu.kdev@gmail.com>
+M:	bcm-kernel-feedback-list@broadcom.com
+S:	Maintained
+F:	Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt
+F:	drivers/spi/spi-bcm-qspi.*
+F:	drivers/spi/spi-brcmstb-qspi.c
+F:	drivers/spi/spi-iproc-qspi.c
+
 BROADCOM SYSTEMPORT ETHERNET DRIVER
 M:	Florian Fainelli <f.fainelli@gmail.com>
 L:	netdev@vger.kernel.org

drivers/soc/qcom/qcom-geni-se.c

@@ -513,7 +513,7 @@ EXPORT_SYMBOL(geni_se_resources_on);
  */
 int geni_se_clk_tbl_get(struct geni_se *se, unsigned long **tbl)
 {
-	unsigned long freq = 0;
+	long freq = 0;
 	int i;
 
 	if (se->clk_perf_tbl) {
@@ -529,7 +529,7 @@ int geni_se_clk_tbl_get(struct geni_se *se, unsigned long **tbl)
 
 	for (i = 0; i < MAX_CLK_PERF_LEVEL; i++) {
 		freq = clk_round_rate(se->clk, freq + 1);
-		if (!freq || freq == se->clk_perf_tbl[i - 1])
+		if (freq <= 0 || freq == se->clk_perf_tbl[i - 1])
 			break;
 		se->clk_perf_tbl[i] = freq;
 	}
@@ -544,16 +544,17 @@ EXPORT_SYMBOL(geni_se_clk_tbl_get);
  * @se:		Pointer to the concerned serial engine.
  * @req_freq:	Requested clock frequency.
  * @index:	Index of the resultant frequency in the table.
- * @res_freq:	Resultant frequency which matches or is closer to the
- *		requested frequency.
+ * @res_freq:	Resultant frequency of the source clock.
  * @exact:	Flag to indicate exact multiple requirement of the requested
  *		frequency.
  *
- * This function is called by the protocol drivers to determine the matching
- * or exact multiple of the requested frequency, as provided by the serial
- * engine clock in order to meet the performance requirements. If there is
- * no matching or exact multiple of the requested frequency found, then it
- * selects the closest floor frequency, if exact flag is not set.
+ * This function is called by the protocol drivers to determine the best match
+ * of the requested frequency as provided by the serial engine clock in order
+ * to meet the performance requirements.
+ *
+ * If we return success:
+ * - if @exact is true  then @res_freq / <an_integer> == @req_freq
+ * - if @exact is false then @res_freq / <an_integer> <= @req_freq
  *
  * Return: 0 on success, standard Linux error codes on failure.
  */
@@ -564,6 +565,9 @@ int geni_se_clk_freq_match(struct geni_se *se, unsigned long req_freq,
 	unsigned long *tbl;
 	int num_clk_levels;
 	int i;
+	unsigned long best_delta;
+	unsigned long new_delta;
+	unsigned int divider;
 
 	num_clk_levels = geni_se_clk_tbl_get(se, &tbl);
 	if (num_clk_levels < 0)
@@ -572,18 +576,21 @@ int geni_se_clk_freq_match(struct geni_se *se, unsigned long req_freq,
 	if (num_clk_levels == 0)
 		return -EINVAL;
 
-	*res_freq = 0;
+	best_delta = ULONG_MAX;
 	for (i = 0; i < num_clk_levels; i++) {
-		if (!(tbl[i] % req_freq)) {
+		divider = DIV_ROUND_UP(tbl[i], req_freq);
+		new_delta = req_freq - tbl[i] / divider;
+		if (new_delta < best_delta) {
+			/* We have a new best! */
 			*index = i;
 			*res_freq = tbl[i];
-			return 0;
-		}
 
-		if (!(*res_freq) || ((tbl[i] > *res_freq) &&
-				     (tbl[i] < req_freq))) {
-			*index = i;
-			*res_freq = tbl[i];
+			/* If the new best is exact then we're done */
+			if (new_delta == 0)
+				return 0;
+
+			/* Record how close we got */
+			best_delta = new_delta;
 		}
 	}
 

drivers/spi/Kconfig

@@ -129,7 +129,7 @@ config SPI_BCM63XX
 
 config SPI_BCM63XX_HSSPI
 	tristate "Broadcom BCM63XX HS SPI controller driver"
-	depends on BCM63XX || COMPILE_TEST
+	depends on BCM63XX || ARCH_BCM_63XX || COMPILE_TEST
 	help
 	  This enables support for the High Speed SPI controller present on
 	  newer Broadcom BCM63XX SoCs.
@@ -520,6 +520,12 @@ config SPI_RSPI
 	help
 	  SPI driver for Renesas RSPI and QSPI blocks.
 
+config SPI_QCOM_QSPI
+	tristate "QTI QSPI controller"
+	depends on ARCH_QCOM
+	help
+	  QSPI(Quad SPI) driver for Qualcomm QSPI controller.
+
 config SPI_QUP
 	tristate "Qualcomm SPI controller with QUP interface"
 	depends on ARCH_QCOM || (ARM && COMPILE_TEST)
@@ -533,6 +539,18 @@ config SPI_QUP
 	  This driver can also be built as a module.  If so, the module
 	  will be called spi_qup.
 
+config SPI_QCOM_GENI
+	tristate "Qualcomm GENI based SPI controller"
+	depends on QCOM_GENI_SE
+	help
+	  This driver supports GENI serial engine based SPI controller in
+	  master mode on the Qualcomm Technologies Inc.'s SoCs. If you say
+	  yes to this option, support will be included for the built-in SPI
+	  interface on the Qualcomm Technologies Inc.'s SoCs.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called spi-geni-qcom.
+
 config SPI_S3C24XX
 	tristate "Samsung S3C24XX series SPI"
 	depends on ARCH_S3C24XX
@@ -596,6 +614,22 @@ config SPI_SIRF
 	help
 	  SPI driver for CSR SiRFprimaII SoCs
 
+config SPI_SLAVE_MT27XX
+	tristate "MediaTek SPI slave device"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	depends on SPI_SLAVE
+	help
+	  This selects the MediaTek(R) SPI slave device driver.
+	  If you want to use MediaTek(R) SPI slave interface,
+	  say Y or M here.If you are not sure, say N.
+	  SPI slave drivers for Mediatek MT27XX series ARM SoCs.
+
+config SPI_SPRD
+	tristate "Spreadtrum SPI controller"
+	depends on ARCH_SPRD || COMPILE_TEST
+	help
+	  SPI driver for Spreadtrum SoCs.
+
 config SPI_SPRD_ADI
 	tristate "Spreadtrum ADI controller"
 	depends on ARCH_SPRD || COMPILE_TEST
@@ -613,6 +647,15 @@ config SPI_STM32
 	  is not available, the driver automatically falls back to
 	  PIO mode.
 
+config SPI_STM32_QSPI
+	tristate "STMicroelectronics STM32 QUAD SPI controller"
+	depends on ARCH_STM32 || COMPILE_TEST
+	depends on OF
+	help
+	  This enables support for the Quad SPI controller in master mode.
+	  This driver does not support generic SPI. The implementation only
+	  supports spi-mem interface.
+
 config SPI_ST_SSC4
 	tristate "STMicroelectronics SPI SSC-based driver"
 	depends on ARCH_STI || COMPILE_TEST

drivers/spi/Makefile

@@ -74,6 +74,8 @@ obj-$(CONFIG_SPI_PPC4xx)		+= spi-ppc4xx.o
 spi-pxa2xx-platform-objs		:= spi-pxa2xx.o spi-pxa2xx-dma.o
 obj-$(CONFIG_SPI_PXA2XX)		+= spi-pxa2xx-platform.o
 obj-$(CONFIG_SPI_PXA2XX_PCI)		+= spi-pxa2xx-pci.o
+obj-$(CONFIG_SPI_QCOM_GENI)		+= spi-geni-qcom.o
+obj-$(CONFIG_SPI_QCOM_QSPI)		+= spi-qcom-qspi.o
 obj-$(CONFIG_SPI_QUP)			+= spi-qup.o
 obj-$(CONFIG_SPI_ROCKCHIP)		+= spi-rockchip.o
 obj-$(CONFIG_SPI_RB4XX)			+= spi-rb4xx.o
@@ -88,8 +90,11 @@ obj-$(CONFIG_SPI_SH_HSPI)		+= spi-sh-hspi.o
 obj-$(CONFIG_SPI_SH_MSIOF)		+= spi-sh-msiof.o
 obj-$(CONFIG_SPI_SH_SCI)		+= spi-sh-sci.o
 obj-$(CONFIG_SPI_SIRF)		+= spi-sirf.o
+obj-$(CONFIG_SPI_SLAVE_MT27XX)          += spi-slave-mt27xx.o
+obj-$(CONFIG_SPI_SPRD)			+= spi-sprd.o
 obj-$(CONFIG_SPI_SPRD_ADI)		+= spi-sprd-adi.o
 obj-$(CONFIG_SPI_STM32) 		+= spi-stm32.o
+obj-$(CONFIG_SPI_STM32_QSPI) 		+= spi-stm32-qspi.o
 obj-$(CONFIG_SPI_ST_SSC4)		+= spi-st-ssc4.o
 obj-$(CONFIG_SPI_SUN4I)			+= spi-sun4i.o
 obj-$(CONFIG_SPI_SUN6I)			+= spi-sun6i.o

drivers/spi/spi-atmel.c

@@ -1767,10 +1767,8 @@ static int atmel_spi_suspend(struct device *dev)
 
 	/* Stop the queue running */
 	ret = spi_master_suspend(master);
-	if (ret) {
-		dev_warn(dev, "cannot suspend master\n");
+	if (ret)
 		return ret;
-	}
 
 	if (!pm_runtime_suspended(dev))
 		atmel_spi_runtime_suspend(dev);
@@ -1799,11 +1797,7 @@ static int atmel_spi_resume(struct device *dev)
 	}
 
 	/* Start the queue running */
-	ret = spi_master_resume(master);
-	if (ret)
-		dev_err(dev, "problem starting queue (%d)\n", ret);
-
-	return ret;
+	return spi_master_resume(master);
 }
 #endif
 

drivers/spi/spi-bcm-qspi.c

@@ -89,7 +89,7 @@
 #define BSPI_BPP_MODE_SELECT_MASK		BIT(8)
 #define BSPI_BPP_ADDR_SELECT_MASK		BIT(16)
 
-#define BSPI_READ_LENGTH			512
+#define BSPI_READ_LENGTH			256
 
 /* MSPI register offsets */
 #define MSPI_SPCR0_LSB				0x000
@@ -355,7 +355,7 @@ static int bcm_qspi_bspi_set_flex_mode(struct bcm_qspi *qspi,
 	int bpc = 0, bpp = 0;
 	u8 command = op->cmd.opcode;
 	int width  = op->cmd.buswidth ? op->cmd.buswidth : SPI_NBITS_SINGLE;
-	int addrlen = op->addr.nbytes * 8;
+	int addrlen = op->addr.nbytes;
 	int flex_mode = 1;
 
 	dev_dbg(&qspi->pdev->dev, "set flex mode w %x addrlen %x hp %d\n",

drivers/spi/spi-bcm63xx-hsspi.c

@@ -101,6 +101,7 @@ struct bcm63xx_hsspi {
 
 	struct platform_device *pdev;
 	struct clk *clk;
+	struct clk *pll_clk;
 	void __iomem *regs;
 	u8 __iomem *fifo;
 
@@ -332,7 +333,7 @@ static int bcm63xx_hsspi_probe(struct platform_device *pdev)
 	struct resource *res_mem;
 	void __iomem *regs;
 	struct device *dev = &pdev->dev;
-	struct clk *clk;
+	struct clk *clk, *pll_clk = NULL;
 	int irq, ret;
 	u32 reg, rate, num_cs = HSSPI_SPI_MAX_CS;
 
@@ -358,7 +359,7 @@ static int bcm63xx_hsspi_probe(struct platform_device *pdev)
 
 	rate = clk_get_rate(clk);
 	if (!rate) {
-		struct clk *pll_clk = devm_clk_get(dev, "pll");
+		pll_clk = devm_clk_get(dev, "pll");
 
 		if (IS_ERR(pll_clk)) {
 			ret = PTR_ERR(pll_clk);
@@ -373,19 +374,20 @@ static int bcm63xx_hsspi_probe(struct platform_device *pdev)
 		clk_disable_unprepare(pll_clk);
 		if (!rate) {
 			ret = -EINVAL;
-			goto out_disable_clk;
+			goto out_disable_pll_clk;
 		}
 	}
 
 	master = spi_alloc_master(&pdev->dev, sizeof(*bs));
 	if (!master) {
 		ret = -ENOMEM;
-		goto out_disable_clk;
+		goto out_disable_pll_clk;
 	}
 
 	bs = spi_master_get_devdata(master);
 	bs->pdev = pdev;
 	bs->clk = clk;
+	bs->pll_clk = pll_clk;
 	bs->regs = regs;
 	bs->speed_hz = rate;
 	bs->fifo = (u8 __iomem *)(bs->regs + HSSPI_FIFO_REG(0));
@@ -440,6 +442,8 @@ static int bcm63xx_hsspi_probe(struct platform_device *pdev)
 
 out_put_master:
 	spi_master_put(master);
+out_disable_pll_clk:
+	clk_disable_unprepare(pll_clk);
 out_disable_clk:
 	clk_disable_unprepare(clk);
 	return ret;
@@ -453,6 +457,7 @@ static int bcm63xx_hsspi_remove(struct platform_device *pdev)
 
 	/* reset the hardware and block queue progress */
 	__raw_writel(0, bs->regs + HSSPI_INT_MASK_REG);
+	clk_disable_unprepare(bs->pll_clk);
 	clk_disable_unprepare(bs->clk);
 
 	return 0;
@@ -465,6 +470,7 @@ static int bcm63xx_hsspi_suspend(struct device *dev)
 	struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
 
 	spi_master_suspend(master);
+	clk_disable_unprepare(bs->pll_clk);
 	clk_disable_unprepare(bs->clk);
 
 	return 0;
@@ -480,6 +486,12 @@ static int bcm63xx_hsspi_resume(struct device *dev)
 	if (ret)
 		return ret;
 
+	if (bs->pll_clk) {
+		ret = clk_prepare_enable(bs->pll_clk);
+		if (ret)
+			return ret;
+	}
+
 	spi_master_resume(master);
 
 	return 0;

drivers/spi/spi-davinci.c

@@ -208,13 +208,11 @@ static inline void clear_io_bits(void __iomem *addr, u32 bits)
 static void davinci_spi_chipselect(struct spi_device *spi, int value)
 {
 	struct davinci_spi *dspi;
-	struct davinci_spi_platform_data *pdata;
 	struct davinci_spi_config *spicfg = spi->controller_data;
 	u8 chip_sel = spi->chip_select;
 	u16 spidat1 = CS_DEFAULT;
 
 	dspi = spi_master_get_devdata(spi->master);
-	pdata = &dspi->pdata;
 
 	/* program delay transfers if tx_delay is non zero */
 	if (spicfg && spicfg->wdelay)
@@ -232,7 +230,8 @@ static void davinci_spi_chipselect(struct spi_device *spi, int value)
 				!(spi->mode & SPI_CS_HIGH));
 	} else {
 		if (value == BITBANG_CS_ACTIVE) {
-			spidat1 |= SPIDAT1_CSHOLD_MASK;
+			if (!(spi->mode & SPI_CS_WORD))
+				spidat1 |= SPIDAT1_CSHOLD_MASK;
 			spidat1 &= ~(0x1 << chip_sel);
 		}
 	}
@@ -421,26 +420,17 @@ static int davinci_spi_setup(struct spi_device *spi)
 {
 	int retval = 0;
 	struct davinci_spi *dspi;
-	struct davinci_spi_platform_data *pdata;
 	struct spi_master *master = spi->master;
 	struct device_node *np = spi->dev.of_node;
 	bool internal_cs = true;
 
 	dspi = spi_master_get_devdata(spi->master);
-	pdata = &dspi->pdata;
 
 	if (!(spi->mode & SPI_NO_CS)) {
 		if (np && (master->cs_gpios != NULL) && (spi->cs_gpio >= 0)) {
 			retval = gpio_direction_output(
 				      spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
 			internal_cs = false;
-		} else if (pdata->chip_sel &&
-			   spi->chip_select < pdata->num_chipselect &&
-			   pdata->chip_sel[spi->chip_select] != SPI_INTERN_CS) {
-			spi->cs_gpio = pdata->chip_sel[spi->chip_select];
-			retval = gpio_direction_output(
-				      spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
-			internal_cs = false;
 		}
 
 		if (retval) {
@@ -449,8 +439,9 @@ static int davinci_spi_setup(struct spi_device *spi)
 			return retval;
 		}
 
-		if (internal_cs)
+		if (internal_cs) {
 			set_io_bits(dspi->base + SPIPC0, 1 << spi->chip_select);
+		}
 	}
 
 	if (spi->mode & SPI_READY)
@@ -985,7 +976,7 @@ static int davinci_spi_probe(struct platform_device *pdev)
 	dspi->prescaler_limit = pdata->prescaler_limit;
 	dspi->version = pdata->version;
 
-	dspi->bitbang.flags = SPI_NO_CS | SPI_LSB_FIRST | SPI_LOOP;
+	dspi->bitbang.flags = SPI_NO_CS | SPI_LSB_FIRST | SPI_LOOP | SPI_CS_WORD;
 	if (dspi->version == SPI_VERSION_2)
 		dspi->bitbang.flags |= SPI_READY;
 

drivers/spi/spi-dw-mmio.c

@@ -34,8 +34,9 @@ struct dw_spi_mmio {
 };
 
 #define MSCC_CPU_SYSTEM_CTRL_GENERAL_CTRL	0x24
-#define OCELOT_IF_SI_OWNER_MASK			GENMASK(5, 4)
 #define OCELOT_IF_SI_OWNER_OFFSET		4
+#define JAGUAR2_IF_SI_OWNER_OFFSET		6
+#define MSCC_IF_SI_OWNER_MASK			GENMASK(1, 0)
 #define MSCC_IF_SI_OWNER_SISL			0
 #define MSCC_IF_SI_OWNER_SIBM			1
 #define MSCC_IF_SI_OWNER_SIMC			2
@@ -76,7 +77,8 @@ static void dw_spi_mscc_set_cs(struct spi_device *spi, bool enable)
 }
 
 static int dw_spi_mscc_init(struct platform_device *pdev,
-			    struct dw_spi_mmio *dwsmmio)
+			    struct dw_spi_mmio *dwsmmio,
+			    const char *cpu_syscon, u32 if_si_owner_offset)
 {
 	struct dw_spi_mscc *dwsmscc;
 	struct resource *res;
@@ -92,7 +94,7 @@ static int dw_spi_mscc_init(struct platform_device *pdev,
 		return PTR_ERR(dwsmscc->spi_mst);
 	}
 
-	dwsmscc->syscon = syscon_regmap_lookup_by_compatible("mscc,ocelot-cpu-syscon");
+	dwsmscc->syscon = syscon_regmap_lookup_by_compatible(cpu_syscon);
 	if (IS_ERR(dwsmscc->syscon))
 		return PTR_ERR(dwsmscc->syscon);
 
@@ -101,8 +103,8 @@ static int dw_spi_mscc_init(struct platform_device *pdev,
 
 	/* Select the owner of the SI interface */
 	regmap_update_bits(dwsmscc->syscon, MSCC_CPU_SYSTEM_CTRL_GENERAL_CTRL,
-			   OCELOT_IF_SI_OWNER_MASK,
-			   MSCC_IF_SI_OWNER_SIMC << OCELOT_IF_SI_OWNER_OFFSET);
+			   MSCC_IF_SI_OWNER_MASK << if_si_owner_offset,
+			   MSCC_IF_SI_OWNER_SIMC << if_si_owner_offset);
 
 	dwsmmio->dws.set_cs = dw_spi_mscc_set_cs;
 	dwsmmio->priv = dwsmscc;
@@ -110,6 +112,28 @@ static int dw_spi_mscc_init(struct platform_device *pdev,
 	return 0;
 }
 
+static int dw_spi_mscc_ocelot_init(struct platform_device *pdev,
+				   struct dw_spi_mmio *dwsmmio)
+{
+	return dw_spi_mscc_init(pdev, dwsmmio, "mscc,ocelot-cpu-syscon",
+				OCELOT_IF_SI_OWNER_OFFSET);
+}
+
+static int dw_spi_mscc_jaguar2_init(struct platform_device *pdev,
+				    struct dw_spi_mmio *dwsmmio)
+{
+	return dw_spi_mscc_init(pdev, dwsmmio, "mscc,jaguar2-cpu-syscon",
+				JAGUAR2_IF_SI_OWNER_OFFSET);
+}
+
+static int dw_spi_alpine_init(struct platform_device *pdev,
+			      struct dw_spi_mmio *dwsmmio)
+{
+	dwsmmio->dws.cs_override = 1;
+
+	return 0;
+}
+
 static int dw_spi_mmio_probe(struct platform_device *pdev)
 {
 	int (*init_func)(struct platform_device *pdev,
@@ -212,7 +236,9 @@ static int dw_spi_mmio_remove(struct platform_device *pdev)
 
 static const struct of_device_id dw_spi_mmio_of_match[] = {
 	{ .compatible = "snps,dw-apb-ssi", },
-	{ .compatible = "mscc,ocelot-spi", .data = dw_spi_mscc_init},
+	{ .compatible = "mscc,ocelot-spi", .data = dw_spi_mscc_ocelot_init},
+	{ .compatible = "mscc,jaguar2-spi", .data = dw_spi_mscc_jaguar2_init},
+	{ .compatible = "amazon,alpine-dw-apb-ssi", .data = dw_spi_alpine_init},
 	{ /* end of table */}
 };
 MODULE_DEVICE_TABLE(of, dw_spi_mmio_of_match);

drivers/spi/spi-dw.c

@@ -144,6 +144,8 @@ void dw_spi_set_cs(struct spi_device *spi, bool enable)
 
 	if (!enable)
 		dw_writel(dws, DW_SPI_SER, BIT(spi->chip_select));
+	else if (dws->cs_override)
+		dw_writel(dws, DW_SPI_SER, 0);
 }
 EXPORT_SYMBOL_GPL(dw_spi_set_cs);
 
@@ -308,15 +310,10 @@ static int dw_spi_transfer_one(struct spi_controller *master,
 		dws->current_freq = transfer->speed_hz;
 		spi_set_clk(dws, chip->clk_div);
 	}
-	if (transfer->bits_per_word == 8) {
-		dws->n_bytes = 1;
-		dws->dma_width = 1;
-	} else if (transfer->bits_per_word == 16) {
-		dws->n_bytes = 2;
-		dws->dma_width = 2;
-	} else {
-		return -EINVAL;
-	}
+
+	dws->n_bytes = DIV_ROUND_UP(transfer->bits_per_word, BITS_PER_BYTE);
+	dws->dma_width = DIV_ROUND_UP(transfer->bits_per_word, BITS_PER_BYTE);
+
 	/* Default SPI mode is SCPOL = 0, SCPH = 0 */
 	cr0 = (transfer->bits_per_word - 1)
 		| (chip->type << SPI_FRF_OFFSET)
@@ -468,6 +465,10 @@ static void spi_hw_init(struct device *dev, struct dw_spi *dws)
 		dws->fifo_len = (fifo == 1) ? 0 : fifo;
 		dev_dbg(dev, "Detected FIFO size: %u bytes\n", dws->fifo_len);
 	}
+
+	/* enable HW fixup for explicit CS deselect for Amazon's alpine chip */
+	if (dws->cs_override)
+		dw_writel(dws, DW_SPI_CS_OVERRIDE, 0xF);
 }
 
 int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
@@ -496,7 +497,7 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
 	}
 
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LOOP;
-	master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
+	master->bits_per_word_mask =  SPI_BPW_RANGE_MASK(4, 16);
 	master->bus_num = dws->bus_num;
 	master->num_chipselect = dws->num_cs;
 	master->setup = dw_spi_setup;
@@ -572,13 +573,8 @@ EXPORT_SYMBOL_GPL(dw_spi_suspend_host);
 
 int dw_spi_resume_host(struct dw_spi *dws)
 {
-	int ret;
-
 	spi_hw_init(&dws->master->dev, dws);
-	ret = spi_controller_resume(dws->master);
-	if (ret)
-		dev_err(&dws->master->dev, "fail to start queue (%d)\n", ret);
-	return ret;
+	return spi_controller_resume(dws->master);
 }
 EXPORT_SYMBOL_GPL(dw_spi_resume_host);
 

drivers/spi/spi-dw.h

@@ -32,6 +32,7 @@
 #define DW_SPI_IDR			0x58
 #define DW_SPI_VERSION			0x5c
 #define DW_SPI_DR			0x60
+#define DW_SPI_CS_OVERRIDE		0xf4
 
 /* Bit fields in CTRLR0 */
 #define SPI_DFS_OFFSET			0
@@ -109,6 +110,7 @@ struct dw_spi {
 	u32			fifo_len;	/* depth of the FIFO buffer */
 	u32			max_freq;	/* max bus freq supported */
 
+	int			cs_override;
 	u32			reg_io_width;	/* DR I/O width in bytes */
 	u16			bus_num;
 	u16			num_cs;		/* supported slave numbers */

drivers/spi/spi-ep93xx.c

@@ -246,6 +246,19 @@ static int ep93xx_spi_read_write(struct spi_master *master)
 	return -EINPROGRESS;
 }
 
+static enum dma_transfer_direction
+ep93xx_dma_data_to_trans_dir(enum dma_data_direction dir)
+{
+	switch (dir) {
+	case DMA_TO_DEVICE:
+		return DMA_MEM_TO_DEV;
+	case DMA_FROM_DEVICE:
+		return DMA_DEV_TO_MEM;
+	default:
+		return DMA_TRANS_NONE;
+	}
+}
+
 /**
  * ep93xx_spi_dma_prepare() - prepares a DMA transfer
  * @master: SPI master
@@ -257,7 +270,7 @@ static int ep93xx_spi_read_write(struct spi_master *master)
  */
 static struct dma_async_tx_descriptor *
 ep93xx_spi_dma_prepare(struct spi_master *master,
-		       enum dma_transfer_direction dir)
+		       enum dma_data_direction dir)
 {
 	struct ep93xx_spi *espi = spi_master_get_devdata(master);
 	struct spi_transfer *xfer = master->cur_msg->state;
@@ -277,9 +290,9 @@ ep93xx_spi_dma_prepare(struct spi_master *master,
 		buswidth = DMA_SLAVE_BUSWIDTH_1_BYTE;
 
 	memset(&conf, 0, sizeof(conf));
-	conf.direction = dir;
+	conf.direction = ep93xx_dma_data_to_trans_dir(dir);
 
-	if (dir == DMA_DEV_TO_MEM) {
+	if (dir == DMA_FROM_DEVICE) {
 		chan = espi->dma_rx;
 		buf = xfer->rx_buf;
 		sgt = &espi->rx_sgt;
@@ -343,7 +356,8 @@ ep93xx_spi_dma_prepare(struct spi_master *master,
 	if (!nents)
 		return ERR_PTR(-ENOMEM);
 
-	txd = dmaengine_prep_slave_sg(chan, sgt->sgl, nents, dir, DMA_CTRL_ACK);
+	txd = dmaengine_prep_slave_sg(chan, sgt->sgl, nents, conf.direction,
+				      DMA_CTRL_ACK);
 	if (!txd) {
 		dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
 		return ERR_PTR(-ENOMEM);
@@ -360,13 +374,13 @@ ep93xx_spi_dma_prepare(struct spi_master *master,
  * unmapped.
  */
 static void ep93xx_spi_dma_finish(struct spi_master *master,
-				  enum dma_transfer_direction dir)
+				  enum dma_data_direction dir)
 {
 	struct ep93xx_spi *espi = spi_master_get_devdata(master);
 	struct dma_chan *chan;
 	struct sg_table *sgt;
 
-	if (dir == DMA_DEV_TO_MEM) {
+	if (dir == DMA_FROM_DEVICE) {
 		chan = espi->dma_rx;
 		sgt = &espi->rx_sgt;
 	} else {
@@ -381,8 +395,8 @@ static void ep93xx_spi_dma_callback(void *callback_param)
 {
 	struct spi_master *master = callback_param;
 
-	ep93xx_spi_dma_finish(master, DMA_MEM_TO_DEV);
-	ep93xx_spi_dma_finish(master, DMA_DEV_TO_MEM);
+	ep93xx_spi_dma_finish(master, DMA_TO_DEVICE);
+	ep93xx_spi_dma_finish(master, DMA_FROM_DEVICE);
 
 	spi_finalize_current_transfer(master);
 }
@@ -392,15 +406,15 @@ static int ep93xx_spi_dma_transfer(struct spi_master *master)
 	struct ep93xx_spi *espi = spi_master_get_devdata(master);
 	struct dma_async_tx_descriptor *rxd, *txd;
 
-	rxd = ep93xx_spi_dma_prepare(master, DMA_DEV_TO_MEM);
+	rxd = ep93xx_spi_dma_prepare(master, DMA_FROM_DEVICE);
 	if (IS_ERR(rxd)) {
 		dev_err(&master->dev, "DMA RX failed: %ld\n", PTR_ERR(rxd));
 		return PTR_ERR(rxd);
 	}
 
-	txd = ep93xx_spi_dma_prepare(master, DMA_MEM_TO_DEV);
+	txd = ep93xx_spi_dma_prepare(master, DMA_TO_DEVICE);
 	if (IS_ERR(txd)) {
-		ep93xx_spi_dma_finish(master, DMA_DEV_TO_MEM);
+		ep93xx_spi_dma_finish(master, DMA_FROM_DEVICE);
 		dev_err(&master->dev, "DMA TX failed: %ld\n", PTR_ERR(txd));
 		return PTR_ERR(txd);
 	}

drivers/spi/spi-fsl-espi.c

@@ -798,10 +798,8 @@ static int of_fsl_espi_suspend(struct device *dev)
 	int ret;
 
 	ret = spi_master_suspend(master);
-	if (ret) {
-		dev_warn(dev, "cannot suspend master\n");
+	if (ret)
 		return ret;
-	}
 
 	return pm_runtime_force_suspend(dev);
 }

drivers/spi/spi-fsl-lpspi.c

@@ -276,7 +276,7 @@ static int fsl_lpspi_config(struct fsl_lpspi_data *fsl_lpspi)
 
 	fsl_lpspi_set_watermark(fsl_lpspi);
 
-	temp = CFGR1_PCSCFG | CFGR1_MASTER | CFGR1_NOSTALL;
+	temp = CFGR1_PCSCFG | CFGR1_MASTER;
 	if (fsl_lpspi->config.mode & SPI_CS_HIGH)
 		temp |= CFGR1_PCSPOL;
 	writel(temp, fsl_lpspi->base + IMX7ULP_CFGR1);

drivers/spi/spi-gpio.c

@@ -295,9 +295,11 @@ static int spi_gpio_request(struct device *dev,
 	spi_gpio->miso = devm_gpiod_get_optional(dev, "miso", GPIOD_IN);
 	if (IS_ERR(spi_gpio->miso))
 		return PTR_ERR(spi_gpio->miso);
-	if (!spi_gpio->miso)
-		/* HW configuration without MISO pin */
-		*mflags |= SPI_MASTER_NO_RX;
+	/*
+	 * No setting SPI_MASTER_NO_RX here - if there is only a MOSI
+	 * pin connected the host can still do RX by changing the
+	 * direction of the line.
+	 */
 
 	spi_gpio->sck = devm_gpiod_get(dev, "sck", GPIOD_OUT_LOW);
 	if (IS_ERR(spi_gpio->sck))
@@ -423,7 +425,7 @@ static int spi_gpio_probe(struct platform_device *pdev)
 	spi_gpio->bitbang.chipselect = spi_gpio_chipselect;
 	spi_gpio->bitbang.set_line_direction = spi_gpio_set_direction;
 
-	if ((master_flags & (SPI_MASTER_NO_TX | SPI_MASTER_NO_RX)) == 0) {
+	if ((master_flags & SPI_MASTER_NO_TX) == 0) {
 		spi_gpio->bitbang.txrx_word[SPI_MODE_0] = spi_gpio_txrx_word_mode0;
 		spi_gpio->bitbang.txrx_word[SPI_MODE_1] = spi_gpio_txrx_word_mode1;
 		spi_gpio->bitbang.txrx_word[SPI_MODE_2] = spi_gpio_txrx_word_mode2;
@@ -447,10 +449,8 @@ static int spi_gpio_probe(struct platform_device *pdev)
 static int spi_gpio_remove(struct platform_device *pdev)
 {
 	struct spi_gpio			*spi_gpio;
-	struct spi_gpio_platform_data	*pdata;
 
 	spi_gpio = platform_get_drvdata(pdev);
-	pdata = dev_get_platdata(&pdev->dev);
 
 	/* stop() unregisters child devices too */
 	spi_bitbang_stop(&spi_gpio->bitbang);

drivers/spi/spi-imx.c

@@ -63,6 +63,7 @@ struct spi_imx_devtype_data {
 	void (*trigger)(struct spi_imx_data *);
 	int (*rx_available)(struct spi_imx_data *);
 	void (*reset)(struct spi_imx_data *);
+	void (*setup_wml)(struct spi_imx_data *);
 	void (*disable)(struct spi_imx_data *);
 	bool has_dmamode;
 	bool has_slavemode;
@@ -216,7 +217,6 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi,
 			 struct spi_transfer *transfer)
 {
 	struct spi_imx_data *spi_imx = spi_master_get_devdata(master);
-	unsigned int bytes_per_word, i;
 
 	if (!master->dma_rx)
 		return false;
@@ -224,14 +224,9 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi,
 	if (spi_imx->slave_mode)
 		return false;
 
-	bytes_per_word = spi_imx_bytes_per_word(transfer->bits_per_word);
-
-	for (i = spi_imx->devtype_data->fifo_size / 2; i > 0; i--) {
-		if (!(transfer->len % (i * bytes_per_word)))
-			break;
-	}
+	if (transfer->len < spi_imx->devtype_data->fifo_size)
+		return false;
 
-	spi_imx->wml = i;
 	spi_imx->dynamic_burst = 0;
 
 	return true;
@@ -583,18 +578,21 @@ static int mx51_ecspi_config(struct spi_device *spi)
 	else			/* SCLK is _very_ slow */
 		usleep_range(delay, delay + 10);
 
+	return 0;
+}
+
+static void mx51_setup_wml(struct spi_imx_data *spi_imx)
+{
 	/*
 	 * Configure the DMA register: setup the watermark
 	 * and enable DMA request.
 	 */
 
-	writel(MX51_ECSPI_DMA_RX_WML(spi_imx->wml) |
+	writel(MX51_ECSPI_DMA_RX_WML(spi_imx->wml - 1) |
 		MX51_ECSPI_DMA_TX_WML(spi_imx->wml) |
 		MX51_ECSPI_DMA_RXT_WML(spi_imx->wml) |
 		MX51_ECSPI_DMA_TEDEN | MX51_ECSPI_DMA_RXDEN |
 		MX51_ECSPI_DMA_RXTDEN, spi_imx->base + MX51_ECSPI_DMA);
-
-	return 0;
 }
 
 static int mx51_ecspi_rx_available(struct spi_imx_data *spi_imx)
@@ -931,6 +929,7 @@ static struct spi_imx_devtype_data imx51_ecspi_devtype_data = {
 	.trigger = mx51_ecspi_trigger,
 	.rx_available = mx51_ecspi_rx_available,
 	.reset = mx51_ecspi_reset,
+	.setup_wml = mx51_setup_wml,
 	.fifo_size = 64,
 	.has_dmamode = true,
 	.dynamic_burst = true,
@@ -1138,7 +1137,6 @@ static int spi_imx_setupxfer(struct spi_device *spi,
 				 struct spi_transfer *t)
 {
 	struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
-	int ret;
 
 	if (!t)
 		return 0;
@@ -1179,12 +1177,6 @@ static int spi_imx_setupxfer(struct spi_device *spi,
 	else
 		spi_imx->usedma = 0;
 
-	if (spi_imx->usedma) {
-		ret = spi_imx_dma_configure(spi->master);
-		if (ret)
-			return ret;
-	}
-
 	if (is_imx53_ecspi(spi_imx) && spi_imx->slave_mode) {
 		spi_imx->rx = mx53_ecspi_rx_slave;
 		spi_imx->tx = mx53_ecspi_tx_slave;
@@ -1289,6 +1281,31 @@ static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
 	unsigned long timeout;
 	struct spi_master *master = spi_imx->bitbang.master;
 	struct sg_table *tx = &transfer->tx_sg, *rx = &transfer->rx_sg;
+	struct scatterlist *last_sg = sg_last(rx->sgl, rx->nents);
+	unsigned int bytes_per_word, i;
+	int ret;
+
+	/* Get the right burst length from the last sg to ensure no tail data */
+	bytes_per_word = spi_imx_bytes_per_word(transfer->bits_per_word);
+	for (i = spi_imx->devtype_data->fifo_size / 2; i > 0; i--) {
+		if (!(sg_dma_len(last_sg) % (i * bytes_per_word)))
+			break;
+	}
+	/* Use 1 as wml in case no available burst length got */
+	if (i == 0)
+		i = 1;
+
+	spi_imx->wml =  i;
+
+	ret = spi_imx_dma_configure(master);
+	if (ret)
+		return ret;
+
+	if (!spi_imx->devtype_data->setup_wml) {
+		dev_err(spi_imx->dev, "No setup_wml()?\n");
+		return -EINVAL;
+	}
+	spi_imx->devtype_data->setup_wml(spi_imx);
 
 	/*
 	 * The TX DMA setup starts the transfer, so make sure RX is configured

drivers/spi/spi-mem.c

@@ -12,6 +12,8 @@
 
 #include "internals.h"
 
+#define SPI_MEM_MAX_BUSWIDTH		4
+
 /**
  * spi_controller_dma_map_mem_op_data() - DMA-map the buffer attached to a
  *					  memory operation
@@ -149,6 +151,44 @@ static bool spi_mem_default_supports_op(struct spi_mem *mem,
 }
 EXPORT_SYMBOL_GPL(spi_mem_default_supports_op);
 
+static bool spi_mem_buswidth_is_valid(u8 buswidth)
+{
+	if (hweight8(buswidth) > 1 || buswidth > SPI_MEM_MAX_BUSWIDTH)
+		return false;
+
+	return true;
+}
+
+static int spi_mem_check_op(const struct spi_mem_op *op)
+{
+	if (!op->cmd.buswidth)
+		return -EINVAL;
+
+	if ((op->addr.nbytes && !op->addr.buswidth) ||
+	    (op->dummy.nbytes && !op->dummy.buswidth) ||
+	    (op->data.nbytes && !op->data.buswidth))
+		return -EINVAL;
+
+	if (!spi_mem_buswidth_is_valid(op->cmd.buswidth) ||
+	    !spi_mem_buswidth_is_valid(op->addr.buswidth) ||
+	    !spi_mem_buswidth_is_valid(op->dummy.buswidth) ||
+	    !spi_mem_buswidth_is_valid(op->data.buswidth))
+		return -EINVAL;
+
+	return 0;
+}
+
+static bool spi_mem_internal_supports_op(struct spi_mem *mem,
+					 const struct spi_mem_op *op)
+{
+	struct spi_controller *ctlr = mem->spi->controller;
+
+	if (ctlr->mem_ops && ctlr->mem_ops->supports_op)
+		return ctlr->mem_ops->supports_op(mem, op);
+
+	return spi_mem_default_supports_op(mem, op);
+}
+
 /**
  * spi_mem_supports_op() - Check if a memory device and the controller it is
  *			   connected to support a specific memory operation
@@ -166,12 +206,10 @@ EXPORT_SYMBOL_GPL(spi_mem_default_supports_op);
  */
 bool spi_mem_supports_op(struct spi_mem *mem, const struct spi_mem_op *op)
 {
-	struct spi_controller *ctlr = mem->spi->controller;
-
-	if (ctlr->mem_ops && ctlr->mem_ops->supports_op)
-		return ctlr->mem_ops->supports_op(mem, op);
+	if (spi_mem_check_op(op))
+		return false;
 
-	return spi_mem_default_supports_op(mem, op);
+	return spi_mem_internal_supports_op(mem, op);
 }
 EXPORT_SYMBOL_GPL(spi_mem_supports_op);
 
@@ -196,7 +234,11 @@ int spi_mem_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
 	u8 *tmpbuf;
 	int ret;
 
-	if (!spi_mem_supports_op(mem, op))
+	ret = spi_mem_check_op(op);
+	if (ret)
+		return ret;
+
+	if (!spi_mem_internal_supports_op(mem, op))
 		return -ENOTSUPP;
 
 	if (ctlr->mem_ops) {
@@ -346,10 +388,25 @@ EXPORT_SYMBOL_GPL(spi_mem_get_name);
 int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
 {
 	struct spi_controller *ctlr = mem->spi->controller;
+	size_t len;
+
+	len = sizeof(op->cmd.opcode) + op->addr.nbytes + op->dummy.nbytes;
 
 	if (ctlr->mem_ops && ctlr->mem_ops->adjust_op_size)
 		return ctlr->mem_ops->adjust_op_size(mem, op);
 
+	if (!ctlr->mem_ops || !ctlr->mem_ops->exec_op) {
+		if (len > spi_max_transfer_size(mem->spi))
+			return -EINVAL;
+
+		op->data.nbytes = min3((size_t)op->data.nbytes,
+				       spi_max_transfer_size(mem->spi),
+				       spi_max_message_size(mem->spi) -
+				       len);
+		if (!op->data.nbytes)
+			return -EINVAL;
+	}
+
 	return 0;
 }
 EXPORT_SYMBOL_GPL(spi_mem_adjust_op_size);

drivers/spi/spi-mt65xx.c

@@ -98,6 +98,7 @@ struct mtk_spi {
 	struct clk *parent_clk, *sel_clk, *spi_clk;
 	struct spi_transfer *cur_transfer;
 	u32 xfer_len;
+	u32 num_xfered;
 	struct scatterlist *tx_sgl, *rx_sgl;
 	u32 tx_sgl_len, rx_sgl_len;
 	const struct mtk_spi_compatible *dev_comp;
@@ -385,6 +386,7 @@ static int mtk_spi_fifo_transfer(struct spi_master *master,
 
 	mdata->cur_transfer = xfer;
 	mdata->xfer_len = min(MTK_SPI_MAX_FIFO_SIZE, xfer->len);
+	mdata->num_xfered = 0;
 	mtk_spi_prepare_transfer(master, xfer);
 	mtk_spi_setup_packet(master);
 
@@ -415,6 +417,7 @@ static int mtk_spi_dma_transfer(struct spi_master *master,
 	mdata->tx_sgl_len = 0;
 	mdata->rx_sgl_len = 0;
 	mdata->cur_transfer = xfer;
+	mdata->num_xfered = 0;
 
 	mtk_spi_prepare_transfer(master, xfer);
 
@@ -482,7 +485,7 @@ static int mtk_spi_setup(struct spi_device *spi)
 
 static irqreturn_t mtk_spi_interrupt(int irq, void *dev_id)
 {
-	u32 cmd, reg_val, cnt, remainder;
+	u32 cmd, reg_val, cnt, remainder, len;
 	struct spi_master *master = dev_id;
 	struct mtk_spi *mdata = spi_master_get_devdata(master);
 	struct spi_transfer *trans = mdata->cur_transfer;
@@ -497,36 +500,38 @@ static irqreturn_t mtk_spi_interrupt(int irq, void *dev_id)
 		if (trans->rx_buf) {
 			cnt = mdata->xfer_len / 4;
 			ioread32_rep(mdata->base + SPI_RX_DATA_REG,
-				     trans->rx_buf, cnt);
+				     trans->rx_buf + mdata->num_xfered, cnt);
 			remainder = mdata->xfer_len % 4;
 			if (remainder > 0) {
 				reg_val = readl(mdata->base + SPI_RX_DATA_REG);
-				memcpy(trans->rx_buf + (cnt * 4),
-					&reg_val, remainder);
+				memcpy(trans->rx_buf +
+					mdata->num_xfered +
+					(cnt * 4),
+					&reg_val,
+					remainder);
 			}
 		}
 
-		trans->len -= mdata->xfer_len;
-		if (!trans->len) {
+		mdata->num_xfered += mdata->xfer_len;
+		if (mdata->num_xfered == trans->len) {
 			spi_finalize_current_transfer(master);
 			return IRQ_HANDLED;
 		}
 
-		if (trans->tx_buf)
-			trans->tx_buf += mdata->xfer_len;
-		if (trans->rx_buf)
-			trans->rx_buf += mdata->xfer_len;
-
-		mdata->xfer_len = min(MTK_SPI_MAX_FIFO_SIZE, trans->len);
+		len = trans->len - mdata->num_xfered;
+		mdata->xfer_len = min(MTK_SPI_MAX_FIFO_SIZE, len);
 		mtk_spi_setup_packet(master);
 
-		cnt = trans->len / 4;
-		iowrite32_rep(mdata->base + SPI_TX_DATA_REG, trans->tx_buf, cnt);
+		cnt = len / 4;
+		iowrite32_rep(mdata->base + SPI_TX_DATA_REG,
+				trans->tx_buf + mdata->num_xfered, cnt);
 
-		remainder = trans->len % 4;
+		remainder = len % 4;
 		if (remainder > 0) {
 			reg_val = 0;
-			memcpy(&reg_val, trans->tx_buf + (cnt * 4), remainder);
+			memcpy(&reg_val,
+				trans->tx_buf + (cnt * 4) + mdata->num_xfered,
+				remainder);
 			writel(reg_val, mdata->base + SPI_TX_DATA_REG);
 		}
 

drivers/spi/spi-omap2-mcspi.c

@@ -33,6 +33,7 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/gcd.h>
+#include <linux/iopoll.h>
 
 #include <linux/spi/spi.h>
 #include <linux/gpio.h>
@@ -126,6 +127,7 @@ struct omap2_mcspi_regs {
 };
 
 struct omap2_mcspi {
+	struct completion	txdone;
 	struct spi_master	*master;
 	/* Virtual base address of the controller */
 	void __iomem		*base;
@@ -135,6 +137,7 @@ struct omap2_mcspi {
 	struct device		*dev;
 	struct omap2_mcspi_regs ctx;
 	int			fifo_depth;
+	bool			slave_aborted;
 	unsigned int		pin_dir:1;
 };
 
@@ -274,19 +277,23 @@ static void omap2_mcspi_set_cs(struct spi_device *spi, bool enable)
 	}
 }
 
-static void omap2_mcspi_set_master_mode(struct spi_master *master)
+static void omap2_mcspi_set_mode(struct spi_master *master)
 {
 	struct omap2_mcspi	*mcspi = spi_master_get_devdata(master);
 	struct omap2_mcspi_regs	*ctx = &mcspi->ctx;
 	u32 l;
 
 	/*
-	 * Setup when switching from (reset default) slave mode
-	 * to single-channel master mode
+	 * Choose master or slave mode
 	 */
 	l = mcspi_read_reg(master, OMAP2_MCSPI_MODULCTRL);
-	l &= ~(OMAP2_MCSPI_MODULCTRL_STEST | OMAP2_MCSPI_MODULCTRL_MS);
-	l |= OMAP2_MCSPI_MODULCTRL_SINGLE;
+	l &= ~(OMAP2_MCSPI_MODULCTRL_STEST);
+	if (spi_controller_is_slave(master)) {
+		l |= (OMAP2_MCSPI_MODULCTRL_MS);
+	} else {
+		l &= ~(OMAP2_MCSPI_MODULCTRL_MS);
+		l |= OMAP2_MCSPI_MODULCTRL_SINGLE;
+	}
 	mcspi_write_reg(master, OMAP2_MCSPI_MODULCTRL, l);
 
 	ctx->modulctrl = l;
@@ -299,7 +306,7 @@ static void omap2_mcspi_set_fifo(const struct spi_device *spi,
 	struct omap2_mcspi_cs *cs = spi->controller_state;
 	struct omap2_mcspi *mcspi;
 	unsigned int wcnt;
-	int max_fifo_depth, fifo_depth, bytes_per_word;
+	int max_fifo_depth, bytes_per_word;
 	u32 chconf, xferlevel;
 
 	mcspi = spi_master_get_devdata(master);
@@ -315,10 +322,6 @@ static void omap2_mcspi_set_fifo(const struct spi_device *spi,
 		else
 			max_fifo_depth = OMAP2_MCSPI_MAX_FIFODEPTH;
 
-		fifo_depth = gcd(t->len, max_fifo_depth);
-		if (fifo_depth < 2 || fifo_depth % bytes_per_word != 0)
-			goto disable_fifo;
-
 		wcnt = t->len / bytes_per_word;
 		if (wcnt > OMAP2_MCSPI_MAX_FIFOWCNT)
 			goto disable_fifo;
@@ -326,16 +329,17 @@ static void omap2_mcspi_set_fifo(const struct spi_device *spi,
 		xferlevel = wcnt << 16;
 		if (t->rx_buf != NULL) {
 			chconf |= OMAP2_MCSPI_CHCONF_FFER;
-			xferlevel |= (fifo_depth - 1) << 8;
+			xferlevel |= (bytes_per_word - 1) << 8;
 		}
+
 		if (t->tx_buf != NULL) {
 			chconf |= OMAP2_MCSPI_CHCONF_FFET;
-			xferlevel |= fifo_depth - 1;
+			xferlevel |= bytes_per_word - 1;
 		}
 
 		mcspi_write_reg(master, OMAP2_MCSPI_XFERLEVEL, xferlevel);
 		mcspi_write_chconf0(spi, chconf);
-		mcspi->fifo_depth = fifo_depth;
+		mcspi->fifo_depth = max_fifo_depth;
 
 		return;
 	}
@@ -353,18 +357,22 @@ static void omap2_mcspi_set_fifo(const struct spi_device *spi,
 
 static int mcspi_wait_for_reg_bit(void __iomem *reg, unsigned long bit)
 {
-	unsigned long timeout;
-
-	timeout = jiffies + msecs_to_jiffies(1000);
-	while (!(readl_relaxed(reg) & bit)) {
-		if (time_after(jiffies, timeout)) {
-			if (!(readl_relaxed(reg) & bit))
-				return -ETIMEDOUT;
-			else
-				return 0;
-		}
-		cpu_relax();
+	u32 val;
+
+	return readl_poll_timeout(reg, val, val & bit, 1, MSEC_PER_SEC);
+}
+
+static int mcspi_wait_for_completion(struct  omap2_mcspi *mcspi,
+				     struct completion *x)
+{
+	if (spi_controller_is_slave(mcspi->master)) {
+		if (wait_for_completion_interruptible(x) ||
+		    mcspi->slave_aborted)
+			return -EINTR;
+	} else {
+		wait_for_completion(x);
 	}
+
 	return 0;
 }
 
@@ -517,7 +525,12 @@ omap2_mcspi_rx_dma(struct spi_device *spi, struct spi_transfer *xfer,
 	dma_async_issue_pending(mcspi_dma->dma_rx);
 	omap2_mcspi_set_dma_req(spi, 1, 1);
 
-	wait_for_completion(&mcspi_dma->dma_rx_completion);
+	ret = mcspi_wait_for_completion(mcspi, &mcspi_dma->dma_rx_completion);
+	if (ret || mcspi->slave_aborted) {
+		dmaengine_terminate_sync(mcspi_dma->dma_rx);
+		omap2_mcspi_set_dma_req(spi, 1, 0);
+		return 0;
+	}
 
 	for (x = 0; x < nb_sizes; x++)
 		kfree(sg_out[x]);
@@ -585,7 +598,6 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer)
 	struct dma_slave_config	cfg;
 	enum dma_slave_buswidth width;
 	unsigned es;
-	u32			burst;
 	void __iomem		*chstat_reg;
 	void __iomem            *irqstat_reg;
 	int			wait_res;
@@ -605,34 +617,49 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer)
 	}
 
 	count = xfer->len;
-	burst = 1;
-
-	if (mcspi->fifo_depth > 0) {
-		if (count > mcspi->fifo_depth)
-			burst = mcspi->fifo_depth / es;
-		else
-			burst = count / es;
-	}
 
 	memset(&cfg, 0, sizeof(cfg));
 	cfg.src_addr = cs->phys + OMAP2_MCSPI_RX0;
 	cfg.dst_addr = cs->phys + OMAP2_MCSPI_TX0;
 	cfg.src_addr_width = width;
 	cfg.dst_addr_width = width;
-	cfg.src_maxburst = burst;
-	cfg.dst_maxburst = burst;
+	cfg.src_maxburst = es;
+	cfg.dst_maxburst = es;
 
 	rx = xfer->rx_buf;
 	tx = xfer->tx_buf;
 
-	if (tx != NULL)
+	mcspi->slave_aborted = false;
+	reinit_completion(&mcspi_dma->dma_tx_completion);
+	reinit_completion(&mcspi_dma->dma_rx_completion);
+	reinit_completion(&mcspi->txdone);
+	if (tx) {
+		/* Enable EOW IRQ to know end of tx in slave mode */
+		if (spi_controller_is_slave(spi->master))
+			mcspi_write_reg(spi->master,
+					OMAP2_MCSPI_IRQENABLE,
+					OMAP2_MCSPI_IRQSTATUS_EOW);
 		omap2_mcspi_tx_dma(spi, xfer, cfg);
+	}
 
 	if (rx != NULL)
 		count = omap2_mcspi_rx_dma(spi, xfer, cfg, es);
 
 	if (tx != NULL) {
-		wait_for_completion(&mcspi_dma->dma_tx_completion);
+		int ret;
+
+		ret = mcspi_wait_for_completion(mcspi, &mcspi_dma->dma_tx_completion);
+		if (ret || mcspi->slave_aborted) {
+			dmaengine_terminate_sync(mcspi_dma->dma_tx);
+			omap2_mcspi_set_dma_req(spi, 0, 0);
+			return 0;
+		}
+
+		if (spi_controller_is_slave(mcspi->master)) {
+			ret = mcspi_wait_for_completion(mcspi, &mcspi->txdone);
+			if (ret || mcspi->slave_aborted)
+				return 0;
+		}
 
 		if (mcspi->fifo_depth > 0) {
 			irqstat_reg = mcspi->base + OMAP2_MCSPI_IRQSTATUS;
@@ -1089,6 +1116,36 @@ static void omap2_mcspi_cleanup(struct spi_device *spi)
 		gpio_free(spi->cs_gpio);
 }
 
+static irqreturn_t omap2_mcspi_irq_handler(int irq, void *data)
+{
+	struct omap2_mcspi *mcspi = data;
+	u32 irqstat;
+
+	irqstat	= mcspi_read_reg(mcspi->master, OMAP2_MCSPI_IRQSTATUS);
+	if (!irqstat)
+		return IRQ_NONE;
+
+	/* Disable IRQ and wakeup slave xfer task */
+	mcspi_write_reg(mcspi->master, OMAP2_MCSPI_IRQENABLE, 0);
+	if (irqstat & OMAP2_MCSPI_IRQSTATUS_EOW)
+		complete(&mcspi->txdone);
+
+	return IRQ_HANDLED;
+}
+
+static int omap2_mcspi_slave_abort(struct spi_master *master)
+{
+	struct omap2_mcspi *mcspi = spi_master_get_devdata(master);
+	struct omap2_mcspi_dma *mcspi_dma = mcspi->dma_channels;
+
+	mcspi->slave_aborted = true;
+	complete(&mcspi_dma->dma_rx_completion);
+	complete(&mcspi_dma->dma_tx_completion);
+	complete(&mcspi->txdone);
+
+	return 0;
+}
+
 static int omap2_mcspi_transfer_one(struct spi_master *master,
 				    struct spi_device *spi,
 				    struct spi_transfer *t)
@@ -1255,10 +1312,20 @@ static bool omap2_mcspi_can_dma(struct spi_master *master,
 				struct spi_device *spi,
 				struct spi_transfer *xfer)
 {
+	struct omap2_mcspi *mcspi = spi_master_get_devdata(spi->master);
+	struct omap2_mcspi_dma *mcspi_dma =
+		&mcspi->dma_channels[spi->chip_select];
+
+	if (!mcspi_dma->dma_rx || !mcspi_dma->dma_tx)
+		return false;
+
+	if (spi_controller_is_slave(master))
+		return true;
+
 	return (xfer->len >= DMA_MIN_BYTES);
 }
 
-static int omap2_mcspi_master_setup(struct omap2_mcspi *mcspi)
+static int omap2_mcspi_controller_setup(struct omap2_mcspi *mcspi)
 {
 	struct spi_master	*master = mcspi->master;
 	struct omap2_mcspi_regs	*ctx = &mcspi->ctx;
@@ -1275,7 +1342,7 @@ static int omap2_mcspi_master_setup(struct omap2_mcspi *mcspi)
 			OMAP2_MCSPI_WAKEUPENABLE_WKEN);
 	ctx->wakeupenable = OMAP2_MCSPI_WAKEUPENABLE_WKEN;
 
-	omap2_mcspi_set_master_mode(master);
+	omap2_mcspi_set_mode(master);
 	pm_runtime_mark_last_busy(mcspi->dev);
 	pm_runtime_put_autosuspend(mcspi->dev);
 	return 0;
@@ -1350,11 +1417,12 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
 	struct device_node	*node = pdev->dev.of_node;
 	const struct of_device_id *match;
 
-	master = spi_alloc_master(&pdev->dev, sizeof *mcspi);
-	if (master == NULL) {
-		dev_dbg(&pdev->dev, "master allocation failed\n");
+	if (of_property_read_bool(node, "spi-slave"))
+		master = spi_alloc_slave(&pdev->dev, sizeof(*mcspi));
+	else
+		master = spi_alloc_master(&pdev->dev, sizeof(*mcspi));
+	if (!master)
 		return -ENOMEM;
-	}
 
 	/* the spi->mode bits understood by this driver: */
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
@@ -1366,6 +1434,7 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
 	master->transfer_one = omap2_mcspi_transfer_one;
 	master->set_cs = omap2_mcspi_set_cs;
 	master->cleanup = omap2_mcspi_cleanup;
+	master->slave_abort = omap2_mcspi_slave_abort;
 	master->dev.of_node = node;
 	master->max_speed_hz = OMAP2_MCSPI_MAX_FREQ;
 	master->min_speed_hz = OMAP2_MCSPI_MAX_FREQ >> 15;
@@ -1417,15 +1486,31 @@ static int omap2_mcspi_probe(struct platform_device *pdev)
 		sprintf(mcspi->dma_channels[i].dma_tx_ch_name, "tx%d", i);
 	}
 
+	status = platform_get_irq(pdev, 0);
+	if (status == -EPROBE_DEFER)
+		goto free_master;
+	if (status < 0) {
+		dev_err(&pdev->dev, "no irq resource found\n");
+		goto free_master;
+	}
+	init_completion(&mcspi->txdone);
+	status = devm_request_irq(&pdev->dev, status,
+				  omap2_mcspi_irq_handler, 0, pdev->name,
+				  mcspi);
+	if (status) {
+		dev_err(&pdev->dev, "Cannot request IRQ");
+		goto free_master;
+	}
+
 	pm_runtime_use_autosuspend(&pdev->dev);
 	pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
 	pm_runtime_enable(&pdev->dev);
 
-	status = omap2_mcspi_master_setup(mcspi);
+	status = omap2_mcspi_controller_setup(mcspi);
 	if (status < 0)
 		goto disable_pm;
 
-	status = devm_spi_register_master(&pdev->dev, master);
+	status = devm_spi_register_controller(&pdev->dev, master);
 	if (status < 0)
 		goto disable_pm;
 

drivers/spi/spi-orion.c

@@ -431,6 +431,7 @@ orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
 	int word_len;
 	struct orion_spi *orion_spi;
 	int cs = spi->chip_select;
+	void __iomem *vaddr;
 
 	word_len = spi->bits_per_word;
 	count = xfer->len;
@@ -441,8 +442,9 @@ orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
 	 * Use SPI direct write mode if base address is available. Otherwise
 	 * fall back to PIO mode for this transfer.
 	 */
-	if ((orion_spi->child[cs].direct_access.vaddr) && (xfer->tx_buf) &&
-	    (word_len == 8)) {
+	vaddr = orion_spi->child[cs].direct_access.vaddr;
+
+	if (vaddr && xfer->tx_buf && word_len == 8) {
 		unsigned int cnt = count / 4;
 		unsigned int rem = count % 4;
 
@@ -450,13 +452,11 @@ orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
 		 * Send the TX-data to the SPI device via the direct
 		 * mapped address window
 		 */
-		iowrite32_rep(orion_spi->child[cs].direct_access.vaddr,
-			      xfer->tx_buf, cnt);
+		iowrite32_rep(vaddr, xfer->tx_buf, cnt);
 		if (rem) {
 			u32 *buf = (u32 *)xfer->tx_buf;
 
-			iowrite8_rep(orion_spi->child[cs].direct_access.vaddr,
-				     &buf[cnt], rem);
+			iowrite8_rep(vaddr, &buf[cnt], rem);
 		}
 
 		return count;
@@ -683,6 +683,7 @@ static int orion_spi_probe(struct platform_device *pdev)
 	}
 
 	for_each_available_child_of_node(pdev->dev.of_node, np) {
+		struct orion_direct_acc *dir_acc;
 		u32 cs;
 		int cs_gpio;
 
@@ -750,14 +751,13 @@ static int orion_spi_probe(struct platform_device *pdev)
 		 * This needs to get extended for the direct SPI-NOR / SPI-NAND
 		 * support, once this gets implemented.
 		 */
-		spi->child[cs].direct_access.vaddr = devm_ioremap(&pdev->dev,
-							    r->start,
-							    PAGE_SIZE);
-		if (!spi->child[cs].direct_access.vaddr) {
+		dir_acc = &spi->child[cs].direct_access;
+		dir_acc->vaddr = devm_ioremap(&pdev->dev, r->start, PAGE_SIZE);
+		if (!dir_acc->vaddr) {
 			status = -ENOMEM;
 			goto out_rel_axi_clk;
 		}
-		spi->child[cs].direct_access.size = PAGE_SIZE;
+		dir_acc->size = PAGE_SIZE;
 
 		dev_info(&pdev->dev, "CS%d configured for direct access\n", cs);
 	}

drivers/spi/spi-pic32-sqi.c

@@ -468,7 +468,7 @@ static int ring_desc_ring_alloc(struct pic32_sqi *sqi)
 	/* allocate coherent DMAable memory for hardware buffer descriptors. */
 	sqi->bd = dma_zalloc_coherent(&sqi->master->dev,
 				      sizeof(*bd) * PESQI_BD_COUNT,
-				      &sqi->bd_dma, GFP_DMA32);
+				      &sqi->bd_dma, GFP_KERNEL);
 	if (!sqi->bd) {
 		dev_err(&sqi->master->dev, "failed allocating dma buffer\n");
 		return -ENOMEM;
@@ -656,7 +656,7 @@ static int pic32_sqi_probe(struct platform_device *pdev)
 	master->max_speed_hz	= clk_get_rate(sqi->base_clk);
 	master->dma_alignment	= 32;
 	master->max_dma_len	= PESQI_BD_BUF_LEN_MAX;
-	master->dev.of_node	= of_node_get(pdev->dev.of_node);
+	master->dev.of_node	= pdev->dev.of_node;
 	master->mode_bits	= SPI_MODE_3 | SPI_MODE_0 | SPI_TX_DUAL |
 				  SPI_RX_DUAL | SPI_TX_QUAD | SPI_RX_QUAD;
 	master->flags		= SPI_MASTER_HALF_DUPLEX;

drivers/spi/spi-pic32.c

@@ -320,7 +320,7 @@ static int pic32_spi_dma_transfer(struct pic32_spi *pic32s,
 	desc_rx = dmaengine_prep_slave_sg(master->dma_rx,
 					  xfer->rx_sg.sgl,
 					  xfer->rx_sg.nents,
-					  DMA_FROM_DEVICE,
+					  DMA_DEV_TO_MEM,
 					  DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 	if (!desc_rx) {
 		ret = -EINVAL;
@@ -330,7 +330,7 @@ static int pic32_spi_dma_transfer(struct pic32_spi *pic32s,
 	desc_tx = dmaengine_prep_slave_sg(master->dma_tx,
 					  xfer->tx_sg.sgl,
 					  xfer->tx_sg.nents,
-					  DMA_TO_DEVICE,
+					  DMA_MEM_TO_DEV,
 					  DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 	if (!desc_tx) {
 		ret = -EINVAL;
@@ -774,7 +774,7 @@ static int pic32_spi_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_master;
 
-	master->dev.of_node	= of_node_get(pdev->dev.of_node);
+	master->dev.of_node	= pdev->dev.of_node;
 	master->mode_bits	= SPI_MODE_3 | SPI_MODE_0 | SPI_CS_HIGH;
 	master->num_chipselect	= 1; /* single chip-select */
 	master->max_speed_hz	= clk_get_rate(pic32s->clk);

drivers/spi/spi-pl022.c

@@ -1490,10 +1490,8 @@ static void do_polling_transfer(struct pl022 *pl022)
 	struct spi_message *message = NULL;
 	struct spi_transfer *transfer = NULL;
 	struct spi_transfer *previous = NULL;
-	struct chip_data *chip;
 	unsigned long time, timeout;
 
-	chip = pl022->cur_chip;
 	message = pl022->cur_msg;
 
 	while (message->state != STATE_DONE) {
@@ -2325,10 +2323,8 @@ static int pl022_suspend(struct device *dev)
 	int ret;
 
 	ret = spi_master_suspend(pl022->master);
-	if (ret) {
-		dev_warn(dev, "cannot suspend master\n");
+	if (ret)
 		return ret;
-	}
 
 	ret = pm_runtime_force_suspend(dev);
 	if (ret) {
@@ -2353,9 +2349,7 @@ static int pl022_resume(struct device *dev)
 
 	/* Start the queue running */
 	ret = spi_master_resume(pl022->master);
-	if (ret)
-		dev_err(dev, "problem starting queue (%d)\n", ret);
-	else
+	if (!ret)
 		dev_dbg(dev, "resumed\n");
 
 	return ret;

drivers/spi/spi-pxa2xx.c

@@ -33,6 +33,7 @@
 #include <linux/clk.h>
 #include <linux/pm_runtime.h>
 #include <linux/acpi.h>
+#include <linux/of_device.h>
 
 #include "spi-pxa2xx.h"
 
@@ -665,9 +666,11 @@ static irqreturn_t interrupt_transfer(struct driver_data *drv_data)
 			bytes_left = drv_data->rx_end - drv_data->rx;
 			switch (drv_data->n_bytes) {
 			case 4:
-				bytes_left >>= 1;
+				bytes_left >>= 2;
+				break;
 			case 2:
 				bytes_left >>= 1;
+				break;
 			}
 
 			rx_thre = pxa2xx_spi_get_rx_default_thre(drv_data);
@@ -1333,9 +1336,6 @@ static void cleanup(struct spi_device *spi)
 	kfree(chip);
 }
 
-#ifdef CONFIG_PCI
-#ifdef CONFIG_ACPI
-
 static const struct acpi_device_id pxa2xx_spi_acpi_match[] = {
 	{ "INT33C0", LPSS_LPT_SSP },
 	{ "INT33C1", LPSS_LPT_SSP },
@@ -1347,23 +1347,6 @@ static const struct acpi_device_id pxa2xx_spi_acpi_match[] = {
 };
 MODULE_DEVICE_TABLE(acpi, pxa2xx_spi_acpi_match);
 
-static int pxa2xx_spi_get_port_id(struct acpi_device *adev)
-{
-	unsigned int devid;
-	int port_id = -1;
-
-	if (adev && adev->pnp.unique_id &&
-	    !kstrtouint(adev->pnp.unique_id, 0, &devid))
-		port_id = devid;
-	return port_id;
-}
-#else /* !CONFIG_ACPI */
-static int pxa2xx_spi_get_port_id(struct acpi_device *adev)
-{
-	return -1;
-}
-#endif
-
 /*
  * PCI IDs of compound devices that integrate both host controller and private
  * integrated DMA engine. Please note these are not used in module
@@ -1410,6 +1393,37 @@ static const struct pci_device_id pxa2xx_spi_pci_compound_match[] = {
 	{ },
 };
 
+static const struct of_device_id pxa2xx_spi_of_match[] = {
+	{ .compatible = "marvell,mmp2-ssp", .data = (void *)MMP2_SSP },
+	{},
+};
+MODULE_DEVICE_TABLE(of, pxa2xx_spi_of_match);
+
+#ifdef CONFIG_ACPI
+
+static int pxa2xx_spi_get_port_id(struct acpi_device *adev)
+{
+	unsigned int devid;
+	int port_id = -1;
+
+	if (adev && adev->pnp.unique_id &&
+	    !kstrtouint(adev->pnp.unique_id, 0, &devid))
+		port_id = devid;
+	return port_id;
+}
+
+#else /* !CONFIG_ACPI */
+
+static int pxa2xx_spi_get_port_id(struct acpi_device *adev)
+{
+	return -1;
+}
+
+#endif /* CONFIG_ACPI */
+
+
+#ifdef CONFIG_PCI
+
 static bool pxa2xx_spi_idma_filter(struct dma_chan *chan, void *param)
 {
 	struct device *dev = param;
@@ -1420,6 +1434,8 @@ static bool pxa2xx_spi_idma_filter(struct dma_chan *chan, void *param)
 	return true;
 }
 
+#endif /* CONFIG_PCI */
+
 static struct pxa2xx_spi_master *
 pxa2xx_spi_init_pdata(struct platform_device *pdev)
 {
@@ -1429,11 +1445,15 @@ pxa2xx_spi_init_pdata(struct platform_device *pdev)
 	struct resource *res;
 	const struct acpi_device_id *adev_id = NULL;
 	const struct pci_device_id *pcidev_id = NULL;
-	int type;
+	const struct of_device_id *of_id = NULL;
+	enum pxa_ssp_type type;
 
 	adev = ACPI_COMPANION(&pdev->dev);
 
-	if (dev_is_pci(pdev->dev.parent))
+	if (pdev->dev.of_node)
+		of_id = of_match_device(pdev->dev.driver->of_match_table,
+					&pdev->dev);
+	else if (dev_is_pci(pdev->dev.parent))
 		pcidev_id = pci_match_id(pxa2xx_spi_pci_compound_match,
 					 to_pci_dev(pdev->dev.parent));
 	else if (adev)
@@ -1443,9 +1463,11 @@ pxa2xx_spi_init_pdata(struct platform_device *pdev)
 		return NULL;
 
 	if (adev_id)
-		type = (int)adev_id->driver_data;
+		type = (enum pxa_ssp_type)adev_id->driver_data;
 	else if (pcidev_id)
-		type = (int)pcidev_id->driver_data;
+		type = (enum pxa_ssp_type)pcidev_id->driver_data;
+	else if (of_id)
+		type = (enum pxa_ssp_type)of_id->data;
 	else
 		return NULL;
 
@@ -1464,11 +1486,13 @@ pxa2xx_spi_init_pdata(struct platform_device *pdev)
 	if (IS_ERR(ssp->mmio_base))
 		return NULL;
 
+#ifdef CONFIG_PCI
 	if (pcidev_id) {
 		pdata->tx_param = pdev->dev.parent;
 		pdata->rx_param = pdev->dev.parent;
 		pdata->dma_filter = pxa2xx_spi_idma_filter;
 	}
+#endif
 
 	ssp->clk = devm_clk_get(&pdev->dev, NULL);
 	ssp->irq = platform_get_irq(pdev, 0);
@@ -1482,14 +1506,6 @@ pxa2xx_spi_init_pdata(struct platform_device *pdev)
 	return pdata;
 }
 
-#else /* !CONFIG_PCI */
-static inline struct pxa2xx_spi_master *
-pxa2xx_spi_init_pdata(struct platform_device *pdev)
-{
-	return NULL;
-}
-#endif
-
 static int pxa2xx_spi_fw_translate_cs(struct spi_controller *master,
 				      unsigned int cs)
 {
@@ -1764,14 +1780,6 @@ static int pxa2xx_spi_remove(struct platform_device *pdev)
 	return 0;
 }
 
-static void pxa2xx_spi_shutdown(struct platform_device *pdev)
-{
-	int status = 0;
-
-	if ((status = pxa2xx_spi_remove(pdev)) != 0)
-		dev_err(&pdev->dev, "shutdown failed with %d\n", status);
-}
-
 #ifdef CONFIG_PM_SLEEP
 static int pxa2xx_spi_suspend(struct device *dev)
 {
@@ -1808,13 +1816,7 @@ static int pxa2xx_spi_resume(struct device *dev)
 		lpss_ssp_setup(drv_data);
 
 	/* Start the queue running */
-	status = spi_controller_resume(drv_data->master);
-	if (status != 0) {
-		dev_err(dev, "problem starting queue (%d)\n", status);
-		return status;
-	}
-
-	return 0;
+	return spi_controller_resume(drv_data->master);
 }
 #endif
 
@@ -1848,10 +1850,10 @@ static struct platform_driver driver = {
 		.name	= "pxa2xx-spi",
 		.pm	= &pxa2xx_spi_pm_ops,
 		.acpi_match_table = ACPI_PTR(pxa2xx_spi_acpi_match),
+		.of_match_table = of_match_ptr(pxa2xx_spi_of_match),
 	},
 	.probe = pxa2xx_spi_probe,
 	.remove = pxa2xx_spi_remove,
-	.shutdown = pxa2xx_spi_shutdown,
 };
 
 static int __init pxa2xx_spi_init(void)

drivers/spi/spi-rb4xx.c

@@ -159,7 +159,7 @@ static int rb4xx_spi_probe(struct platform_device *pdev)
 	master->bus_num = 0;
 	master->num_chipselect = 3;
 	master->mode_bits = SPI_TX_DUAL;
-	master->bits_per_word_mask = BIT(7);
+	master->bits_per_word_mask = SPI_BPW_MASK(8);
 	master->flags = SPI_MASTER_MUST_TX;
 	master->transfer_one = rb4xx_transfer_one;
 	master->set_cs = rb4xx_set_cs;

drivers/spi/spi-rockchip.c

@@ -164,7 +164,6 @@ enum rockchip_ssi_type {
 
 struct rockchip_spi_dma_data {
 	struct dma_chan *ch;
-	enum dma_transfer_direction direction;
 	dma_addr_t addr;
 };
 
@@ -202,12 +201,11 @@ struct rockchip_spi {
 
 	bool cs_asserted[ROCKCHIP_SPI_MAX_CS_NUM];
 
-	u32 use_dma;
+	bool use_dma;
 	struct sg_table tx_sg;
 	struct sg_table rx_sg;
 	struct rockchip_spi_dma_data dma_rx;
 	struct rockchip_spi_dma_data dma_tx;
-	struct dma_slave_caps dma_caps;
 };
 
 static inline void spi_enable_chip(struct rockchip_spi *rs, int enable)
@@ -381,6 +379,8 @@ static int rockchip_spi_pio_transfer(struct rockchip_spi *rs)
 {
 	int remain = 0;
 
+	spi_enable_chip(rs, 1);
+
 	do {
 		if (rs->tx) {
 			remain = rs->tx_end - rs->tx;
@@ -445,6 +445,9 @@ static int rockchip_spi_prepare_dma(struct rockchip_spi *rs)
 	struct dma_slave_config rxconf, txconf;
 	struct dma_async_tx_descriptor *rxdesc, *txdesc;
 
+	memset(&rxconf, 0, sizeof(rxconf));
+	memset(&txconf, 0, sizeof(txconf));
+
 	spin_lock_irqsave(&rs->lock, flags);
 	rs->state &= ~RXBUSY;
 	rs->state &= ~TXBUSY;
@@ -452,19 +455,16 @@ static int rockchip_spi_prepare_dma(struct rockchip_spi *rs)
 
 	rxdesc = NULL;
 	if (rs->rx) {
-		rxconf.direction = rs->dma_rx.direction;
+		rxconf.direction = DMA_DEV_TO_MEM;
 		rxconf.src_addr = rs->dma_rx.addr;
 		rxconf.src_addr_width = rs->n_bytes;
-		if (rs->dma_caps.max_burst > 4)
-			rxconf.src_maxburst = 4;
-		else
-			rxconf.src_maxburst = 1;
+		rxconf.src_maxburst = 1;
 		dmaengine_slave_config(rs->dma_rx.ch, &rxconf);
 
 		rxdesc = dmaengine_prep_slave_sg(
 				rs->dma_rx.ch,
 				rs->rx_sg.sgl, rs->rx_sg.nents,
-				rs->dma_rx.direction, DMA_PREP_INTERRUPT);
+				DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT);
 		if (!rxdesc)
 			return -EINVAL;
 
@@ -474,19 +474,16 @@ static int rockchip_spi_prepare_dma(struct rockchip_spi *rs)
 
 	txdesc = NULL;
 	if (rs->tx) {
-		txconf.direction = rs->dma_tx.direction;
+		txconf.direction = DMA_MEM_TO_DEV;
 		txconf.dst_addr = rs->dma_tx.addr;
 		txconf.dst_addr_width = rs->n_bytes;
-		if (rs->dma_caps.max_burst > 4)
-			txconf.dst_maxburst = 4;
-		else
-			txconf.dst_maxburst = 1;
+		txconf.dst_maxburst = rs->fifo_len / 2;
 		dmaengine_slave_config(rs->dma_tx.ch, &txconf);
 
 		txdesc = dmaengine_prep_slave_sg(
 				rs->dma_tx.ch,
 				rs->tx_sg.sgl, rs->tx_sg.nents,
-				rs->dma_tx.direction, DMA_PREP_INTERRUPT);
+				DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT);
 		if (!txdesc) {
 			if (rxdesc)
 				dmaengine_terminate_sync(rs->dma_rx.ch);
@@ -506,6 +503,8 @@ static int rockchip_spi_prepare_dma(struct rockchip_spi *rs)
 		dma_async_issue_pending(rs->dma_rx.ch);
 	}
 
+	spi_enable_chip(rs, 1);
+
 	if (txdesc) {
 		spin_lock_irqsave(&rs->lock, flags);
 		rs->state |= TXBUSY;
@@ -514,7 +513,8 @@ static int rockchip_spi_prepare_dma(struct rockchip_spi *rs)
 		dma_async_issue_pending(rs->dma_tx.ch);
 	}
 
-	return 0;
+	/* 1 means the transfer is in progress */
+	return 1;
 }
 
 static void rockchip_spi_config(struct rockchip_spi *rs)
@@ -578,7 +578,7 @@ static void rockchip_spi_config(struct rockchip_spi *rs)
 	writel_relaxed(rs->fifo_len / 2 - 1, rs->regs + ROCKCHIP_SPI_TXFTLR);
 	writel_relaxed(rs->fifo_len / 2 - 1, rs->regs + ROCKCHIP_SPI_RXFTLR);
 
-	writel_relaxed(0, rs->regs + ROCKCHIP_SPI_DMATDLR);
+	writel_relaxed(rs->fifo_len / 2 - 1, rs->regs + ROCKCHIP_SPI_DMATDLR);
 	writel_relaxed(0, rs->regs + ROCKCHIP_SPI_DMARDLR);
 	writel_relaxed(dmacr, rs->regs + ROCKCHIP_SPI_DMACR);
 
@@ -597,7 +597,6 @@ static int rockchip_spi_transfer_one(
 		struct spi_device *spi,
 		struct spi_transfer *xfer)
 {
-	int ret = 0;
 	struct rockchip_spi *rs = spi_master_get_devdata(master);
 
 	WARN_ON(readl_relaxed(rs->regs + ROCKCHIP_SPI_SSIENR) &&
@@ -635,30 +634,16 @@ static int rockchip_spi_transfer_one(
 
 	/* we need prepare dma before spi was enabled */
 	if (master->can_dma && master->can_dma(master, spi, xfer))
-		rs->use_dma = 1;
+		rs->use_dma = true;
 	else
-		rs->use_dma = 0;
+		rs->use_dma = false;
 
 	rockchip_spi_config(rs);
 
-	if (rs->use_dma) {
-		if (rs->tmode == CR0_XFM_RO) {
-			/* rx: dma must be prepared first */
-			ret = rockchip_spi_prepare_dma(rs);
-			spi_enable_chip(rs, 1);
-		} else {
-			/* tx or tr: spi must be enabled first */
-			spi_enable_chip(rs, 1);
-			ret = rockchip_spi_prepare_dma(rs);
-		}
-		/* successful DMA prepare means the transfer is in progress */
-		ret = ret ? ret : 1;
-	} else {
-		spi_enable_chip(rs, 1);
-		ret = rockchip_spi_pio_transfer(rs);
-	}
+	if (rs->use_dma)
+		return rockchip_spi_prepare_dma(rs);
 
-	return ret;
+	return rockchip_spi_pio_transfer(rs);
 }
 
 static bool rockchip_spi_can_dma(struct spi_master *master,
@@ -780,11 +765,8 @@ static int rockchip_spi_probe(struct platform_device *pdev)
 	}
 
 	if (rs->dma_tx.ch && rs->dma_rx.ch) {
-		dma_get_slave_caps(rs->dma_rx.ch, &(rs->dma_caps));
 		rs->dma_tx.addr = (dma_addr_t)(mem->start + ROCKCHIP_SPI_TXDR);
 		rs->dma_rx.addr = (dma_addr_t)(mem->start + ROCKCHIP_SPI_RXDR);
-		rs->dma_tx.direction = DMA_MEM_TO_DEV;
-		rs->dma_rx.direction = DMA_DEV_TO_MEM;
 
 		master->can_dma = rockchip_spi_can_dma;
 		master->dma_tx = rs->dma_tx.ch;

drivers/spi/spi-rspi.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * SH RSPI driver
  *
@@ -6,15 +7,6 @@
  *
  * Based on spi-sh.c:
  * Copyright (C) 2011 Renesas Solutions Corp.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/module.h>

drivers/spi/spi-sh-hspi.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * SuperH HSPI bus driver
  *
@@ -7,15 +8,6 @@
  * Based on pxa2xx_spi.c:
  * Copyright (C) 2011 Renesas Solutions Corp.
  * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/clk.h>
@@ -316,6 +308,6 @@ static struct platform_driver hspi_driver = {
 module_platform_driver(hspi_driver);
 
 MODULE_DESCRIPTION("SuperH HSPI bus driver");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
 MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>");
 MODULE_ALIAS("platform:sh-hspi");

drivers/spi/spi-sh-msiof.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * SuperH MSIOF SPI Master Interface
  *
  * Copyright (c) 2009 Magnus Damm
  * Copyright (C) 2014 Renesas Electronics Corporation
  * Copyright (C) 2014-2017 Glider bvba
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
  */
 
 #include <linux/bitmap.h>
@@ -1343,8 +1339,8 @@ static int sh_msiof_spi_probe(struct platform_device *pdev)
 
 	i = platform_get_irq(pdev, 0);
 	if (i < 0) {
-		dev_err(&pdev->dev, "cannot get platform IRQ\n");
-		ret = -ENOENT;
+		dev_err(&pdev->dev, "cannot get IRQ\n");
+		ret = i;
 		goto err1;
 	}
 

drivers/spi/spi-sh.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * SH SPI bus driver
  *
@@ -5,15 +6,6 @@
  *
  * Based on pxa2xx_spi.c:
  * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/module.h>
@@ -522,6 +514,6 @@ static struct platform_driver spi_sh_driver = {
 module_platform_driver(spi_sh_driver);
 
 MODULE_DESCRIPTION("SH SPI bus driver");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
 MODULE_AUTHOR("Yoshihiro Shimoda");
 MODULE_ALIAS("platform:sh_spi");

drivers/spi/spi-slave-system-control.c

@@ -60,6 +60,7 @@ static void spi_slave_system_control_complete(void *arg)
 	case CMD_REBOOT:
 		dev_info(&priv->spi->dev, "Rebooting system...\n");
 		kernel_restart(NULL);
+		break;
 
 	case CMD_POWEROFF:
 		dev_info(&priv->spi->dev, "Powering off system...\n");

drivers/spi/spi.c

+// SPDX-License-Identifier: GPL-2.0-or-later
 /*
  * SPI init/core code
  *
  * Copyright (C) 2005 David Brownell
  * Copyright (C) 2008 Secret Lab Technologies Ltd.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/kernel.h>
@@ -60,6 +51,7 @@ static void spidev_release(struct device *dev)
 		spi->controller->cleanup(spi);
 
 	spi_controller_put(spi->controller);
+	kfree(spi->driver_override);
 	kfree(spi);
 }
 
@@ -77,6 +69,51 @@ modalias_show(struct device *dev, struct device_attribute *a, char *buf)
 }
 static DEVICE_ATTR_RO(modalias);
 
+static ssize_t driver_override_store(struct device *dev,
+				     struct device_attribute *a,
+				     const char *buf, size_t count)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	const char *end = memchr(buf, '\n', count);
+	const size_t len = end ? end - buf : count;
+	const char *driver_override, *old;
+
+	/* We need to keep extra room for a newline when displaying value */
+	if (len >= (PAGE_SIZE - 1))
+		return -EINVAL;
+
+	driver_override = kstrndup(buf, len, GFP_KERNEL);
+	if (!driver_override)
+		return -ENOMEM;
+
+	device_lock(dev);
+	old = spi->driver_override;
+	if (len) {
+		spi->driver_override = driver_override;
+	} else {
+		/* Emptry string, disable driver override */
+		spi->driver_override = NULL;
+		kfree(driver_override);
+	}
+	device_unlock(dev);
+	kfree(old);
+
+	return count;
+}
+
+static ssize_t driver_override_show(struct device *dev,
+				    struct device_attribute *a, char *buf)
+{
+	const struct spi_device *spi = to_spi_device(dev);
+	ssize_t len;
+
+	device_lock(dev);
+	len = snprintf(buf, PAGE_SIZE, "%s\n", spi->driver_override ? : "");
+	device_unlock(dev);
+	return len;
+}
+static DEVICE_ATTR_RW(driver_override);
+
 #define SPI_STATISTICS_ATTRS(field, file)				\
 static ssize_t spi_controller_##field##_show(struct device *dev,	\
 					     struct device_attribute *attr, \
@@ -158,6 +195,7 @@ SPI_STATISTICS_SHOW(transfers_split_maxsize, "%lu");
 
 static struct attribute *spi_dev_attrs[] = {
 	&dev_attr_modalias.attr,
+	&dev_attr_driver_override.attr,
 	NULL,
 };
 
@@ -305,6 +343,10 @@ static int spi_match_device(struct device *dev, struct device_driver *drv)
 	const struct spi_device	*spi = to_spi_device(dev);
 	const struct spi_driver	*sdrv = to_spi_driver(drv);
 
+	/* Check override first, and if set, only use the named driver */
+	if (spi->driver_override)
+		return strcmp(spi->driver_override, drv->name) == 0;
+
 	/* Attempt an OF style match */
 	if (of_driver_match_device(dev, drv))
 		return 1;
@@ -733,7 +775,9 @@ static void spi_set_cs(struct spi_device *spi, bool enable)
 		enable = !enable;
 
 	if (gpio_is_valid(spi->cs_gpio)) {
-		gpio_set_value(spi->cs_gpio, !enable);
+		/* Honour the SPI_NO_CS flag */
+		if (!(spi->mode & SPI_NO_CS))
+			gpio_set_value(spi->cs_gpio, !enable);
 		/* Some SPI masters need both GPIO CS & slave_select */
 		if ((spi->controller->flags & SPI_MASTER_GPIO_SS) &&
 		    spi->controller->set_cs)
@@ -2783,8 +2827,10 @@ int spi_setup(struct spi_device *spi)
 		return -EINVAL;
 	/* help drivers fail *cleanly* when they need options
 	 * that aren't supported with their current controller
+	 * SPI_CS_WORD has a fallback software implementation,
+	 * so it is ignored here.
 	 */
-	bad_bits = spi->mode & ~spi->controller->mode_bits;
+	bad_bits = spi->mode & ~(spi->controller->mode_bits | SPI_CS_WORD);
 	ugly_bits = bad_bits &
 		    (SPI_TX_DUAL | SPI_TX_QUAD | SPI_RX_DUAL | SPI_RX_QUAD);
 	if (ugly_bits) {
@@ -2838,6 +2884,35 @@ static int __spi_validate(struct spi_device *spi, struct spi_message *message)
 	if (list_empty(&message->transfers))
 		return -EINVAL;
 
+	/* If an SPI controller does not support toggling the CS line on each
+	 * transfer (indicated by the SPI_CS_WORD flag) or we are using a GPIO
+	 * for the CS line, we can emulate the CS-per-word hardware function by
+	 * splitting transfers into one-word transfers and ensuring that
+	 * cs_change is set for each transfer.
+	 */
+	if ((spi->mode & SPI_CS_WORD) && (!(ctlr->mode_bits & SPI_CS_WORD) ||
+					  gpio_is_valid(spi->cs_gpio))) {
+		size_t maxsize;
+		int ret;
+
+		maxsize = (spi->bits_per_word + 7) / 8;
+
+		/* spi_split_transfers_maxsize() requires message->spi */
+		message->spi = spi;
+
+		ret = spi_split_transfers_maxsize(ctlr, message, maxsize,
+						  GFP_KERNEL);
+		if (ret)
+			return ret;
+
+		list_for_each_entry(xfer, &message->transfers, transfer_list) {
+			/* don't change cs_change on the last entry in the list */
+			if (list_is_last(&xfer->transfer_list, &message->transfers))
+				break;
+			xfer->cs_change = 1;
+		}
+	}
+
 	/* Half-duplex links include original MicroWire, and ones with
 	 * only one data pin like SPI_3WIRE (switches direction) or where
 	 * either MOSI or MISO is missing.  They can also be caused by
@@ -3323,20 +3398,23 @@ EXPORT_SYMBOL_GPL(spi_write_then_read);
 
 /*-------------------------------------------------------------------------*/
 
-#if IS_ENABLED(CONFIG_OF_DYNAMIC)
+#if IS_ENABLED(CONFIG_OF)
 static int __spi_of_device_match(struct device *dev, void *data)
 {
 	return dev->of_node == data;
 }
 
 /* must call put_device() when done with returned spi_device device */
-static struct spi_device *of_find_spi_device_by_node(struct device_node *node)
+struct spi_device *of_find_spi_device_by_node(struct device_node *node)
 {
 	struct device *dev = bus_find_device(&spi_bus_type, NULL, node,
 						__spi_of_device_match);
 	return dev ? to_spi_device(dev) : NULL;
 }
+EXPORT_SYMBOL_GPL(of_find_spi_device_by_node);
+#endif /* IS_ENABLED(CONFIG_OF) */
 
+#if IS_ENABLED(CONFIG_OF_DYNAMIC)
 static int __spi_of_controller_match(struct device *dev, const void *data)
 {
 	return dev->of_node == data;

drivers/spi/spidev.c

@@ -669,6 +669,7 @@ static const struct of_device_id spidev_dt_ids[] = {
 	{ .compatible = "lineartechnology,ltc2488" },
 	{ .compatible = "ge,achc" },
 	{ .compatible = "semtech,sx1301" },
+	{ .compatible = "lwn,bk4" },
 	{},
 };
 MODULE_DEVICE_TABLE(of, spidev_dt_ids);
@@ -724,11 +725,9 @@ static int spidev_probe(struct spi_device *spi)
 	 * compatible string, it is a Linux implementation thing
 	 * rather than a description of the hardware.
 	 */
-	if (spi->dev.of_node && !of_match_device(spidev_dt_ids, &spi->dev)) {
-		dev_err(&spi->dev, "buggy DT: spidev listed directly in DT\n");
-		WARN_ON(spi->dev.of_node &&
-			!of_match_device(spidev_dt_ids, &spi->dev));
-	}
+	WARN(spi->dev.of_node &&
+	     of_device_is_compatible(spi->dev.of_node, "spidev"),
+	     "%pOF: buggy DT: spidev listed directly in DT\n", spi->dev.of_node);
 
 	spidev_probe_acpi(spi);
 

include/linux/pci.h

@@ -1705,6 +1705,10 @@ static inline int pci_irqd_intx_xlate(struct irq_domain *d,
 				      unsigned long *out_hwirq,
 				      unsigned int *out_type)
 { return -EINVAL; }
+
+static inline const struct pci_device_id *pci_match_id(const struct pci_device_id *ids,
+							 struct pci_dev *dev)
+{ return NULL; }
 #endif /* CONFIG_PCI */
 
 /* Include architecture-dependent settings and functions */

include/linux/platform_data/spi-davinci.h

@@ -36,9 +36,6 @@ enum {
  * @num_chipselect: number of chipselects supported by this SPI master
  * @intr_line:	interrupt line used to connect the SPI IP to the ARM interrupt
  *		controller withn the SoC. Possible values are 0 and 1.
- * @chip_sel:	list of GPIOs which can act as chip-selects for the SPI.
- *		SPI_INTERN_CS denotes internal SPI chip-select. Not necessary
- *		to populate if all chip-selects are internal.
  * @cshold_bug:	set this to true if the SPI controller on your chip requires
  *		a write to CSHOLD bit in between transfers (like in DM355).
  * @dma_event_q: DMA event queue to use if SPI_IO_TYPE_DMA is used for any
@@ -48,7 +45,6 @@ struct davinci_spi_platform_data {
 	u8			version;
 	u8			num_chipselect;
 	u8			intr_line;
-	u8			*chip_sel;
 	u8			prescaler_limit;
 	bool			cshold_bug;
 	enum dma_event_q	dma_event_q;

include/linux/pxa2xx_ssp.h

@@ -196,6 +196,7 @@ enum pxa_ssp_type {
 	PXA27x_SSP,
 	PXA3xx_SSP,
 	PXA168_SSP,
+	MMP2_SSP,
 	PXA910_SSP,
 	CE4100_SSP,
 	QUARK_X1000_SSP,
@@ -217,7 +218,7 @@ struct ssp_device {
 
 	const char	*label;
 	int		port_id;
-	int		type;
+	enum pxa_ssp_type type;
 	int		use_count;
 	int		irq;