Commit b6c5164d authored by Daniel Vetter's avatar Daniel Vetter

drm/i915: Fixup Oops in the pipe config computation

Yet again our current confusion between doing the modeset globally,
but only having the new parameters for one crtc at a time.

So that intel_set_mode essentially already does a global modeset:
intel_modeset_affected_pipes compares the current state with where we
want to go to (which is carefully set up by intel_crtc_set_config) and
then goes through the modeset sequence for any crtc which needs
updating.

Now the issue is that the actual interface with the remaining code
still only works on one crtc, and so we only pass in one fb and one
mode. In intel_set_mode we also only compute one intel_crtc_config
(which should be the one for the crtc we're doing a modeset on).

The reason for that mismatch is twofold:
- We want to eventually do all modeset as global state changes, so
it's just infrastructure prep.
- But even the old semantics can change more than one crtc when you
e.g. move a connector from crtc A to crtc B, then both crtc A and B
need to be updated. Usually that means one pipe is disabled and the
other enabled. This is also the reason why the hack doesn't touch the
disable_pipes mask.

Now hilarity ensued in our kms config restore paths when we actually
try to do a modeset on all crtcs: If the first crtc should be off and
the second should be on, then the call on the first crtc will notice
that the 2nd one should be switched on and so tries to compute the
pipe_config. But due to a lack of passed-in fb (crtc 1 should be off
after all) it only results in tears.

This case is ridiculously easy to hit on gen2/3 where the lvds output
is restricted to pipe B. Note that before the pipe_config bpp rework
gen2/3 didn't care really about the fb->depth, so this is a regression
brought to light with

commit 4e53c2e0
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed Mar 27 00:44:58 2013 +0100

    drm/i915: precompute pipe bpp before touching the hw

But apparently Ajax also managed to blow up pch platforms, probably
with some randomized configs, and pch platforms trip up over the lack
of an fb even in the old code. So this actually goes back to the first
introduction of the new modeset restore code in

commit 45e2b5f6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Fri Nov 23 18:16:34 2012 +0100

    drm/i915: force restore on lid open

Fix this mess by now by justing shunting all the cool new global
modeset logic in intel_modeset_affected_pipes.

v2: Improve commit message and clean up all the comments in
intel_modeset_affected_pipes - since the introduction of the modeset
restore code they've been a bit outdated.

Bugzill: https://bugzilla.redhat.com/show_bug.cgi?id=917725
Cc: stable@vger.kernel.org
References: http://www.mail-archive.com/stable@vger.kernel.org/msg38084.htmlTested-by: default avatarRichard Cochran <richardcochran@gmail.com>
Reviewed-by: default avatarChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: default avatarDaniel Vetter <daniel.vetter@ffwll.ch>
parent dc652f90
......@@ -7712,22 +7712,25 @@ intel_modeset_affected_pipes(struct drm_crtc *crtc, unsigned *modeset_pipes,
if (crtc->enabled)
*prepare_pipes |= 1 << intel_crtc->pipe;
/* We only support modeset on one single crtc, hence we need to do that
* only for the passed in crtc iff we change anything else than just
* disable crtcs.
*
* This is actually not true, to be fully compatible with the old crtc
* helper we automatically disable _any_ output (i.e. doesn't need to be
* connected to the crtc we're modesetting on) if it's disconnected.
* Which is a rather nutty api (since changed the output configuration
* without userspace's explicit request can lead to confusion), but
* alas. Hence we currently need to modeset on all pipes we prepare. */
/*
* For simplicity do a full modeset on any pipe where the output routing
* changed. We could be more clever, but that would require us to be
* more careful with calling the relevant encoder->mode_set functions.
*/
if (*prepare_pipes)
*modeset_pipes = *prepare_pipes;
/* ... and mask these out. */
*modeset_pipes &= ~(*disable_pipes);
*prepare_pipes &= ~(*disable_pipes);
/*
* HACK: We don't (yet) fully support global modesets. intel_set_config
* obies this rule, but the modeset restore mode of
* intel_modeset_setup_hw_state does not.
*/
*modeset_pipes &= 1 << intel_crtc->pipe;
*prepare_pipes &= 1 << intel_crtc->pipe;
}
static bool intel_crtc_in_use(struct drm_crtc *crtc)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment