Commit b7b7da2a authored by Bob Moore's avatar Bob Moore Committed by Rafael J. Wysocki

ACPICA: Split resource descriptor decode strings to a new file

ACPICA commit 00906ae0aff4c6b76abc232ef99700e7d7c0e325

There are enough of these strings to justify a separate file.
Also, these strings are only used for the disassembler and
the debugger. Thus, this change improves ACPICA modularity.

Link: https://github.com/acpica/acpica/commit/00906ae0Signed-off-by: default avatarBob Moore <robert.moore@intel.com>
Signed-off-by: default avatarLv Zheng <lv.zheng@intel.com>
Signed-off-by: default avatarRafael J. Wysocki <rafael.j.wysocki@intel.com>
parent 596878da
......@@ -172,6 +172,7 @@ acpi-y += \
utosi.o \
utownerid.o \
utpredef.o \
utresdecode.o \
utresrc.o \
utstate.o \
utstring.o \
......
/*******************************************************************************
*
* Module Name: utresdecode - Resource descriptor keyword strings
*
******************************************************************************/
/*
* Copyright (C) 2000 - 2017, Intel Corp.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* substantially similar to the "NO WARRANTY" disclaimer below
* ("Disclaimer") and any redistribution must be conditioned upon
* including a substantially similar Disclaimer requirement for further
* binary redistribution.
* 3. Neither the names of the above-listed copyright holders nor the names
* of any contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*/
#include <acpi/acpi.h>
#include "accommon.h"
#include "acresrc.h"
#define _COMPONENT ACPI_UTILITIES
ACPI_MODULE_NAME("utresdecode")
#if defined (ACPI_DEBUG_OUTPUT) || \
defined (ACPI_DISASSEMBLER) || \
defined (ACPI_DEBUGGER)
/*
* Strings used to decode resource descriptors.
* Used by both the disassembler and the debugger resource dump routines
*/
const char *acpi_gbl_bm_decode[] = {
"NotBusMaster",
"BusMaster"
};
const char *acpi_gbl_config_decode[] = {
"0 - Good Configuration",
"1 - Acceptable Configuration",
"2 - Suboptimal Configuration",
"3 - ***Invalid Configuration***",
};
const char *acpi_gbl_consume_decode[] = {
"ResourceProducer",
"ResourceConsumer"
};
const char *acpi_gbl_dec_decode[] = {
"PosDecode",
"SubDecode"
};
const char *acpi_gbl_he_decode[] = {
"Level",
"Edge"
};
const char *acpi_gbl_io_decode[] = {
"Decode10",
"Decode16"
};
const char *acpi_gbl_ll_decode[] = {
"ActiveHigh",
"ActiveLow",
"ActiveBoth",
"Reserved"
};
const char *acpi_gbl_max_decode[] = {
"MaxNotFixed",
"MaxFixed"
};
const char *acpi_gbl_mem_decode[] = {
"NonCacheable",
"Cacheable",
"WriteCombining",
"Prefetchable"
};
const char *acpi_gbl_min_decode[] = {
"MinNotFixed",
"MinFixed"
};
const char *acpi_gbl_mtp_decode[] = {
"AddressRangeMemory",
"AddressRangeReserved",
"AddressRangeACPI",
"AddressRangeNVS"
};
const char *acpi_gbl_rng_decode[] = {
"InvalidRanges",
"NonISAOnlyRanges",
"ISAOnlyRanges",
"EntireRange"
};
const char *acpi_gbl_rw_decode[] = {
"ReadOnly",
"ReadWrite"
};
const char *acpi_gbl_shr_decode[] = {
"Exclusive",
"Shared",
"ExclusiveAndWake", /* ACPI 5.0 */
"SharedAndWake" /* ACPI 5.0 */
};
const char *acpi_gbl_siz_decode[] = {
"Transfer8",
"Transfer8_16",
"Transfer16",
"InvalidSize"
};
const char *acpi_gbl_trs_decode[] = {
"DenseTranslation",
"SparseTranslation"
};
const char *acpi_gbl_ttp_decode[] = {
"TypeStatic",
"TypeTranslation"
};
const char *acpi_gbl_typ_decode[] = {
"Compatibility",
"TypeA",
"TypeB",
"TypeF"
};
const char *acpi_gbl_ppc_decode[] = {
"PullDefault",
"PullUp",
"PullDown",
"PullNone"
};
const char *acpi_gbl_ior_decode[] = {
"IoRestrictionNone",
"IoRestrictionInputOnly",
"IoRestrictionOutputOnly",
"IoRestrictionNoneAndPreserve"
};
const char *acpi_gbl_dts_decode[] = {
"Width8bit",
"Width16bit",
"Width32bit",
"Width64bit",
"Width128bit",
"Width256bit",
};
/* GPIO connection type */
const char *acpi_gbl_ct_decode[] = {
"Interrupt",
"I/O"
};
/* Serial bus type */
const char *acpi_gbl_sbt_decode[] = {
"/* UNKNOWN serial bus type */",
"I2C",
"SPI",
"UART"
};
/* I2C serial bus access mode */
const char *acpi_gbl_am_decode[] = {
"AddressingMode7Bit",
"AddressingMode10Bit"
};
/* I2C serial bus slave mode */
const char *acpi_gbl_sm_decode[] = {
"ControllerInitiated",
"DeviceInitiated"
};
/* SPI serial bus wire mode */
const char *acpi_gbl_wm_decode[] = {
"FourWireMode",
"ThreeWireMode"
};
/* SPI serial clock phase */
const char *acpi_gbl_cph_decode[] = {
"ClockPhaseFirst",
"ClockPhaseSecond"
};
/* SPI serial bus clock polarity */
const char *acpi_gbl_cpo_decode[] = {
"ClockPolarityLow",
"ClockPolarityHigh"
};
/* SPI serial bus device polarity */
const char *acpi_gbl_dp_decode[] = {
"PolarityLow",
"PolarityHigh"
};
/* UART serial bus endian */
const char *acpi_gbl_ed_decode[] = {
"LittleEndian",
"BigEndian"
};
/* UART serial bus bits per byte */
const char *acpi_gbl_bpb_decode[] = {
"DataBitsFive",
"DataBitsSix",
"DataBitsSeven",
"DataBitsEight",
"DataBitsNine",
"/* UNKNOWN Bits per byte */",
"/* UNKNOWN Bits per byte */",
"/* UNKNOWN Bits per byte */"
};
/* UART serial bus stop bits */
const char *acpi_gbl_sb_decode[] = {
"StopBitsZero",
"StopBitsOne",
"StopBitsOnePlusHalf",
"StopBitsTwo"
};
/* UART serial bus flow control */
const char *acpi_gbl_fc_decode[] = {
"FlowControlNone",
"FlowControlHardware",
"FlowControlXON",
"/* UNKNOWN flow control keyword */"
};
/* UART serial bus parity type */
const char *acpi_gbl_pt_decode[] = {
"ParityTypeNone",
"ParityTypeEven",
"ParityTypeOdd",
"ParityTypeMark",
"ParityTypeSpace",
"/* UNKNOWN parity keyword */",
"/* UNKNOWN parity keyword */",
"/* UNKNOWN parity keyword */"
};
/* pin_config type */
const char *acpi_gbl_ptyp_decode[] = {
"Default",
"Bias Pull-up",
"Bias Pull-down",
"Bias Default",
"Bias Disable",
"Bias High Impedance",
"Bias Bus Hold",
"Drive Open Drain",
"Drive Open Source",
"Drive Push Pull",
"Drive Strength",
"Slew Rate",
"Input Debounce",
"Input Schmitt Trigger",
};
#endif
......@@ -48,270 +48,6 @@
#define _COMPONENT ACPI_UTILITIES
ACPI_MODULE_NAME("utresrc")
#if defined(ACPI_DEBUG_OUTPUT) || defined (ACPI_DISASSEMBLER) || defined (ACPI_DEBUGGER)
/*
* Strings used to decode resource descriptors.
* Used by both the disassembler and the debugger resource dump routines
*/
const char *acpi_gbl_bm_decode[] = {
"NotBusMaster",
"BusMaster"
};
const char *acpi_gbl_config_decode[] = {
"0 - Good Configuration",
"1 - Acceptable Configuration",
"2 - Suboptimal Configuration",
"3 - ***Invalid Configuration***",
};
const char *acpi_gbl_consume_decode[] = {
"ResourceProducer",
"ResourceConsumer"
};
const char *acpi_gbl_dec_decode[] = {
"PosDecode",
"SubDecode"
};
const char *acpi_gbl_he_decode[] = {
"Level",
"Edge"
};
const char *acpi_gbl_io_decode[] = {
"Decode10",
"Decode16"
};
const char *acpi_gbl_ll_decode[] = {
"ActiveHigh",
"ActiveLow",
"ActiveBoth",
"Reserved"
};
const char *acpi_gbl_max_decode[] = {
"MaxNotFixed",
"MaxFixed"
};
const char *acpi_gbl_mem_decode[] = {
"NonCacheable",
"Cacheable",
"WriteCombining",
"Prefetchable"
};
const char *acpi_gbl_min_decode[] = {
"MinNotFixed",
"MinFixed"
};
const char *acpi_gbl_mtp_decode[] = {
"AddressRangeMemory",
"AddressRangeReserved",
"AddressRangeACPI",
"AddressRangeNVS"
};
const char *acpi_gbl_rng_decode[] = {
"InvalidRanges",
"NonISAOnlyRanges",
"ISAOnlyRanges",
"EntireRange"
};
const char *acpi_gbl_rw_decode[] = {
"ReadOnly",
"ReadWrite"
};
const char *acpi_gbl_shr_decode[] = {
"Exclusive",
"Shared",
"ExclusiveAndWake", /* ACPI 5.0 */
"SharedAndWake" /* ACPI 5.0 */
};
const char *acpi_gbl_siz_decode[] = {
"Transfer8",
"Transfer8_16",
"Transfer16",
"InvalidSize"
};
const char *acpi_gbl_trs_decode[] = {
"DenseTranslation",
"SparseTranslation"
};
const char *acpi_gbl_ttp_decode[] = {
"TypeStatic",
"TypeTranslation"
};
const char *acpi_gbl_typ_decode[] = {
"Compatibility",
"TypeA",
"TypeB",
"TypeF"
};
const char *acpi_gbl_ppc_decode[] = {
"PullDefault",
"PullUp",
"PullDown",
"PullNone"
};
const char *acpi_gbl_ior_decode[] = {
"IoRestrictionNone",
"IoRestrictionInputOnly",
"IoRestrictionOutputOnly",
"IoRestrictionNoneAndPreserve"
};
const char *acpi_gbl_dts_decode[] = {
"Width8bit",
"Width16bit",
"Width32bit",
"Width64bit",
"Width128bit",
"Width256bit",
};
/* GPIO connection type */
const char *acpi_gbl_ct_decode[] = {
"Interrupt",
"I/O"
};
/* Serial bus type */
const char *acpi_gbl_sbt_decode[] = {
"/* UNKNOWN serial bus type */",
"I2C",
"SPI",
"UART"
};
/* I2C serial bus access mode */
const char *acpi_gbl_am_decode[] = {
"AddressingMode7Bit",
"AddressingMode10Bit"
};
/* I2C serial bus slave mode */
const char *acpi_gbl_sm_decode[] = {
"ControllerInitiated",
"DeviceInitiated"
};
/* SPI serial bus wire mode */
const char *acpi_gbl_wm_decode[] = {
"FourWireMode",
"ThreeWireMode"
};
/* SPI serial clock phase */
const char *acpi_gbl_cph_decode[] = {
"ClockPhaseFirst",
"ClockPhaseSecond"
};
/* SPI serial bus clock polarity */
const char *acpi_gbl_cpo_decode[] = {
"ClockPolarityLow",
"ClockPolarityHigh"
};
/* SPI serial bus device polarity */
const char *acpi_gbl_dp_decode[] = {
"PolarityLow",
"PolarityHigh"
};
/* UART serial bus endian */
const char *acpi_gbl_ed_decode[] = {
"LittleEndian",
"BigEndian"
};
/* UART serial bus bits per byte */
const char *acpi_gbl_bpb_decode[] = {
"DataBitsFive",
"DataBitsSix",
"DataBitsSeven",
"DataBitsEight",
"DataBitsNine",
"/* UNKNOWN Bits per byte */",
"/* UNKNOWN Bits per byte */",
"/* UNKNOWN Bits per byte */"
};
/* UART serial bus stop bits */
const char *acpi_gbl_sb_decode[] = {
"StopBitsZero",
"StopBitsOne",
"StopBitsOnePlusHalf",
"StopBitsTwo"
};
/* UART serial bus flow control */
const char *acpi_gbl_fc_decode[] = {
"FlowControlNone",
"FlowControlHardware",
"FlowControlXON",
"/* UNKNOWN flow control keyword */"
};
/* UART serial bus parity type */
const char *acpi_gbl_pt_decode[] = {
"ParityTypeNone",
"ParityTypeEven",
"ParityTypeOdd",
"ParityTypeMark",
"ParityTypeSpace",
"/* UNKNOWN parity keyword */",
"/* UNKNOWN parity keyword */",
"/* UNKNOWN parity keyword */"
};
/* pin_config type */
const char *acpi_gbl_ptyp_decode[] = {
"Default",
"Bias Pull-up",
"Bias Pull-down",
"Bias Default",
"Bias Disable",
"Bias High Impedance",
"Bias Bus Hold",
"Drive Open Drain",
"Drive Open Source",
"Drive Push Pull",
"Drive Strength",
"Slew Rate",
"Input Debounce",
"Input Schmitt Trigger",
};
#endif
/*
* Base sizes of the raw AML resource descriptors, indexed by resource type.
* Zero indicates a reserved (and therefore invalid) resource type.
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment