Merge tag 'newsoc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull RISC-V SoC updates from Arnd Bergmann:
 "Add support for StarFive JH7100 RISC-V SoC

  This adds support for the StarFive JH7100, including the necessary
  device drivers and DT files for the BeagleV Starlight prototype board,
  with additional boards to be added later. This SoC promises to be the
  first usable low-cost platform for RISC-V.

  I've taken this through the SoC tree in the anticipation of adding a
  few other Arm based SoCs as well, but those did not pass the review in
  time, so it's only this one"

* tag 'newsoc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  reset: starfive-jh7100: Fix 32bit compilation
  RISC-V: Add BeagleV Starlight Beta device tree
  RISC-V: Add initial StarFive JH7100 device tree
  serial: 8250_dw: Add StarFive JH7100 quirk
  dt-bindings: serial: snps-dw-apb-uart: Add JH7100 uarts
  pinctrl: starfive: Add pinctrl driver for StarFive SoCs
  dt-bindings: pinctrl: Add StarFive JH7100 bindings
  dt-bindings: pinctrl: Add StarFive pinctrl definitions
  reset: starfive-jh7100: Add StarFive JH7100 reset driver
  dt-bindings: reset: Add Starfive JH7100 reset bindings
  dt-bindings: reset: Add StarFive JH7100 reset definitions
  clk: starfive: Add JH7100 clock generator driver
  dt-bindings: clock: starfive: Add JH7100 bindings
  dt-bindings: clock: starfive: Add JH7100 clock definitions
  dt-bindings: interrupt-controller: Add StarFive JH7100 plic
  dt-bindings: timer: Add StarFive JH7100 clint
  RISC-V: Add StarFive SoC Kconfig option

Documentation/devicetree/bindings/clock/starfive,jh7100-clkgen.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/starfive,jh7100-clkgen.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7100 Clock Generator
+
+maintainers:
+  - Geert Uytterhoeven <geert@linux-m68k.org>
+  - Emil Renner Berthing <kernel@esmil.dk>
+
+properties:
+  compatible:
+    const: starfive,jh7100-clkgen
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Main clock source (25 MHz)
+      - description: Application-specific clock source (12-27 MHz)
+      - description: RMII reference clock (50 MHz)
+      - description: RGMII RX clock (125 MHz)
+
+  clock-names:
+    items:
+      - const: osc_sys
+      - const: osc_aud
+      - const: gmac_rmii_ref
+      - const: gmac_gr_mii_rxclk
+
+  '#clock-cells':
+    const: 1
+    description:
+      See <dt-bindings/clock/starfive-jh7100.h> for valid indices.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    clock-controller@11800000 {
+            compatible = "starfive,jh7100-clkgen";
+            reg = <0x11800000 0x10000>;
+            clocks = <&osc_sys>, <&osc_aud>, <&gmac_rmii_ref>, <&gmac_gr_mii_rxclk>;
+            clock-names = "osc_sys", "osc_aud", "gmac_rmii_ref", "gmac_gr_mii_rxclk";
+            #clock-cells = <1>;
+    };

Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml

@@ -45,6 +45,7 @@ properties:
     items:
       - enum:
           - sifive,fu540-c000-plic
+          - starfive,jh7100-plic
           - canaan,k210-plic
       - const: sifive,plic-1.0.0
 

Documentation/devicetree/bindings/reset/starfive,jh7100-reset.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/reset/starfive,jh7100-reset.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7100 SoC Reset Controller Device Tree Bindings
+
+maintainers:
+  - Emil Renner Berthing <kernel@esmil.dk>
+
+properties:
+  compatible:
+    enum:
+      - starfive,jh7100-reset
+
+  reg:
+    maxItems: 1
+
+  "#reset-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - "#reset-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    reset-controller@11840000 {
+        compatible = "starfive,jh7100-reset";
+        reg = <0x11840000 0x10000>;
+        #reset-cells = <1>;
+    };
+
+...

Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml

@@ -40,6 +40,11 @@ properties:
               - brcm,bcm11351-dw-apb-uart
               - brcm,bcm21664-dw-apb-uart
           - const: snps,dw-apb-uart
+      - items:
+          - enum:
+              - starfive,jh7100-hsuart
+              - starfive,jh7100-uart
+          - const: snps,dw-apb-uart
       - const: snps,dw-apb-uart
 
   reg:

Documentation/devicetree/bindings/timer/sifive,clint.yaml

@@ -25,6 +25,7 @@ properties:
     items:
       - enum:
           - sifive,fu540-c000-clint
+          - starfive,jh7100-clint
           - canaan,k210-clint
       - const: sifive,clint0
 

MAINTAINERS

@@ -18164,6 +18164,28 @@ M:	Ion Badulescu <ionut@badula.org>
 S:	Odd Fixes
 F:	drivers/net/ethernet/adaptec/starfire*
 
+STARFIVE JH7100 CLOCK DRIVER
+M:	Emil Renner Berthing <kernel@esmil.dk>
+S:	Maintained
+F:	Documentation/devicetree/bindings/clock/starfive,jh7100-clkgen.yaml
+F:	drivers/clk/starfive/clk-starfive-jh7100.c
+F:	include/dt-bindings/clock/starfive-jh7100.h
+
+STARFIVE JH7100 PINCTRL DRIVER
+M:	Emil Renner Berthing <kernel@esmil.dk>
+L:	linux-gpio@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml
+F:	drivers/pinctrl/pinctrl-starfive.c
+F:	include/dt-bindings/pinctrl/pinctrl-starfive.h
+
+STARFIVE JH7100 RESET CONTROLLER DRIVER
+M:	Emil Renner Berthing <kernel@esmil.dk>
+S:	Maintained
+F:	Documentation/devicetree/bindings/reset/starfive,jh7100-reset.yaml
+F:	drivers/reset/reset-starfive-jh7100.c
+F:	include/dt-bindings/reset/starfive-jh7100.h
+
 STATIC BRANCH/CALL
 M:	Peter Zijlstra <peterz@infradead.org>
 M:	Josh Poimboeuf <jpoimboe@redhat.com>

arch/riscv/Kconfig.socs

@@ -19,6 +19,14 @@ config SOC_SIFIVE
 	help
 	  This enables support for SiFive SoC platform hardware.
 
+config SOC_STARFIVE
+	bool "StarFive SoCs"
+	select PINCTRL
+	select RESET_CONTROLLER
+	select SIFIVE_PLIC
+	help
+	  This enables support for StarFive SoC platform hardware.
+
 config SOC_VIRT
 	bool "QEMU Virt Machine"
 	select CLINT_TIMER if RISCV_M_MODE

arch/riscv/boot/dts/Makefile

 # SPDX-License-Identifier: GPL-2.0
 subdir-y += sifive
+subdir-y += starfive
 subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
 subdir-y += microchip
 

arch/riscv/boot/dts/starfive/Makefile

+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_SOC_STARFIVE) += jh7100-beaglev-starlight.dtb

arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts

+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2021 StarFive Technology Co., Ltd.
+ * Copyright (C) 2021 Emil Renner Berthing <kernel@esmil.dk>
+ */
+
+/dts-v1/;
+#include "jh7100.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/pinctrl-starfive.h>
+
+/ {
+	model = "BeagleV Starlight Beta";
+	compatible = "beagle,beaglev-starlight-jh7100-r0", "starfive,jh7100";
+
+	aliases {
+		serial0 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cpus {
+		timebase-frequency = <6250000>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x2 0x0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-ack {
+			gpios = <&gpio 43 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+			linux,default-trigger = "heartbeat";
+			label = "ack";
+		};
+	};
+};
+
+&gpio {
+	i2c0_pins: i2c0-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(62, GPO_LOW,
+				  GPO_I2C0_PAD_SCK_OEN,
+				  GPI_I2C0_PAD_SCK_IN)>,
+				 <GPIOMUX(61, GPO_LOW,
+				  GPO_I2C0_PAD_SDA_OEN,
+				  GPI_I2C0_PAD_SDA_IN)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c1_pins: i2c1-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(47, GPO_LOW,
+				  GPO_I2C1_PAD_SCK_OEN,
+				  GPI_I2C1_PAD_SCK_IN)>,
+				 <GPIOMUX(48, GPO_LOW,
+				  GPO_I2C1_PAD_SDA_OEN,
+				  GPI_I2C1_PAD_SDA_IN)>;
+			bias-pull-up;
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c2_pins: i2c2-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(60, GPO_LOW,
+				  GPO_I2C2_PAD_SCK_OEN,
+				  GPI_I2C2_PAD_SCK_IN)>,
+				 <GPIOMUX(59, GPO_LOW,
+				  GPO_I2C2_PAD_SDA_OEN,
+				  GPI_I2C2_PAD_SDA_IN)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	uart3_pins: uart3-0 {
+		rx-pins {
+			pinmux = <GPIOMUX(13, GPO_LOW, GPO_DISABLE,
+				  GPI_UART3_PAD_SIN)>;
+			bias-pull-up;
+			drive-strength = <14>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+		tx-pins {
+			pinmux = <GPIOMUX(14, GPO_UART3_PAD_SOUT,
+				  GPO_ENABLE, GPI_NONE)>;
+			bias-disable;
+			drive-strength = <35>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <500>;
+	i2c-scl-falling-time-ns = <500>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+
+	pmic@5e {
+		compatible = "ti,tps65086";
+		reg = <0x5e>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		regulators {
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <100>;
+	i2c-scl-falling-time-ns = <100>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <500>;
+	i2c-scl-falling-time-ns = <500>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	status = "okay";
+};
+
+&osc_sys {
+	clock-frequency = <25000000>;
+};
+
+&osc_aud {
+	clock-frequency = <27000000>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "okay";
+};

arch/riscv/boot/dts/starfive/jh7100.dtsi

+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2021 StarFive Technology Co., Ltd.
+ * Copyright (C) 2021 Emil Renner Berthing <kernel@esmil.dk>
+ */
+
+/dts-v1/;
+#include <dt-bindings/clock/starfive-jh7100.h>
+#include <dt-bindings/reset/starfive-jh7100.h>
+
+/ {
+	compatible = "starfive,jh7100";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "sifive,u74-mc", "riscv";
+			reg = <0>;
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+
+			cpu0_intc: interrupt-controller {
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+		};
+
+		cpu@1 {
+			compatible = "sifive,u74-mc", "riscv";
+			reg = <1>;
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+
+			cpu1_intc: interrupt-controller {
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+		};
+	};
+
+	osc_sys: osc_sys {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	osc_aud: osc_aud {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	gmac_rmii_ref: gmac_rmii_ref {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* Should be overridden by the board when needed */
+		clock-frequency = <0>;
+	};
+
+	gmac_gr_mii_rxclk: gmac_gr_mii_rxclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* Should be overridden by the board when needed */
+		clock-frequency = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&plic>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		clint: clint@2000000 {
+			compatible = "starfive,jh7100-clint", "sifive,clint0";
+			reg = <0x0 0x2000000 0x0 0x10000>;
+			interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
+					       &cpu1_intc 3 &cpu1_intc 7>;
+		};
+
+		plic: interrupt-controller@c000000 {
+			compatible = "starfive,jh7100-plic", "sifive,plic-1.0.0";
+			reg = <0x0 0xc000000 0x0 0x4000000>;
+			interrupts-extended = <&cpu0_intc 11 &cpu0_intc 9
+					       &cpu1_intc 11 &cpu1_intc 9>;
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			riscv,ndev = <127>;
+		};
+
+		clkgen: clock-controller@11800000 {
+			compatible = "starfive,jh7100-clkgen";
+			reg = <0x0 0x11800000 0x0 0x10000>;
+			clocks = <&osc_sys>, <&osc_aud>, <&gmac_rmii_ref>, <&gmac_gr_mii_rxclk>;
+			clock-names = "osc_sys", "osc_aud", "gmac_rmii_ref", "gmac_gr_mii_rxclk";
+			#clock-cells = <1>;
+		};
+
+		rstgen: reset-controller@11840000 {
+			compatible = "starfive,jh7100-reset";
+			reg = <0x0 0x11840000 0x0 0x10000>;
+			#reset-cells = <1>;
+		};
+
+		i2c0: i2c@118b0000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x0 0x118b0000 0x0 0x10000>;
+			clocks = <&clkgen JH7100_CLK_I2C0_CORE>,
+				 <&clkgen JH7100_CLK_I2C0_APB>;
+			clock-names = "ref", "pclk";
+			resets = <&rstgen JH7100_RSTN_I2C0_APB>;
+			interrupts = <96>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@118c0000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x0 0x118c0000 0x0 0x10000>;
+			clocks = <&clkgen JH7100_CLK_I2C1_CORE>,
+				 <&clkgen JH7100_CLK_I2C1_APB>;
+			clock-names = "ref", "pclk";
+			resets = <&rstgen JH7100_RSTN_I2C1_APB>;
+			interrupts = <97>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		gpio: pinctrl@11910000 {
+			compatible = "starfive,jh7100-pinctrl";
+			reg = <0x0 0x11910000 0x0 0x10000>,
+			      <0x0 0x11858000 0x0 0x1000>;
+			reg-names = "gpio", "padctl";
+			clocks = <&clkgen JH7100_CLK_GPIO_APB>;
+			resets = <&rstgen JH7100_RSTN_GPIO_APB>;
+			interrupts = <32>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		uart2: serial@12430000 {
+			compatible = "starfive,jh7100-uart", "snps,dw-apb-uart";
+			reg = <0x0 0x12430000 0x0 0x10000>;
+			clocks = <&clkgen JH7100_CLK_UART2_CORE>,
+				 <&clkgen JH7100_CLK_UART2_APB>;
+			clock-names = "baudclk", "apb_pclk";
+			resets = <&rstgen JH7100_RSTN_UART2_APB>;
+			interrupts = <72>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			status = "disabled";
+		};
+
+		uart3: serial@12440000 {
+			compatible = "starfive,jh7100-uart", "snps,dw-apb-uart";
+			reg = <0x0 0x12440000 0x0 0x10000>;
+			clocks = <&clkgen JH7100_CLK_UART3_CORE>,
+				 <&clkgen JH7100_CLK_UART3_APB>;
+			clock-names = "baudclk", "apb_pclk";
+			resets = <&rstgen JH7100_RSTN_UART3_APB>;
+			interrupts = <73>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@12450000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x0 0x12450000 0x0 0x10000>;
+			clocks = <&clkgen JH7100_CLK_I2C2_CORE>,
+				 <&clkgen JH7100_CLK_I2C2_APB>;
+			clock-names = "ref", "pclk";
+			resets = <&rstgen JH7100_RSTN_I2C2_APB>;
+			interrupts = <74>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@12460000 {
+			compatible = "snps,designware-i2c";
+			reg = <0x0 0x12460000 0x0 0x10000>;
+			clocks = <&clkgen JH7100_CLK_I2C3_CORE>,
+				 <&clkgen JH7100_CLK_I2C3_APB>;
+			clock-names = "ref", "pclk";
+			resets = <&rstgen JH7100_RSTN_I2C3_APB>;
+			interrupts = <75>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+	};
+};

drivers/clk/Kconfig

@@ -412,6 +412,7 @@ source "drivers/clk/samsung/Kconfig"
 source "drivers/clk/sifive/Kconfig"
 source "drivers/clk/socfpga/Kconfig"
 source "drivers/clk/sprd/Kconfig"
+source "drivers/clk/starfive/Kconfig"
 source "drivers/clk/sunxi/Kconfig"
 source "drivers/clk/sunxi-ng/Kconfig"
 source "drivers/clk/tegra/Kconfig"

drivers/clk/Makefile

@@ -109,6 +109,7 @@ obj-y					+= socfpga/
 obj-$(CONFIG_PLAT_SPEAR)		+= spear/
 obj-y					+= sprd/
 obj-$(CONFIG_ARCH_STI)			+= st/
+obj-$(CONFIG_SOC_STARFIVE)		+= starfive/
 obj-$(CONFIG_ARCH_SUNXI)		+= sunxi/
 obj-$(CONFIG_SUNXI_CCU)			+= sunxi-ng/
 obj-$(CONFIG_ARCH_TEGRA)		+= tegra/

drivers/clk/starfive/Kconfig

+# SPDX-License-Identifier: GPL-2.0
+
+config CLK_STARFIVE_JH7100
+	bool "StarFive JH7100 clock support"
+	depends on SOC_STARFIVE || COMPILE_TEST
+	default SOC_STARFIVE
+	help
+	  Say yes here to support the clock controller on the StarFive JH7100
+	  SoC.

drivers/clk/starfive/Makefile

+# SPDX-License-Identifier: GPL-2.0
+# StarFive Clock
+obj-$(CONFIG_CLK_STARFIVE_JH7100)	+= clk-starfive-jh7100.o

drivers/pinctrl/Kconfig

@@ -281,6 +281,23 @@ config PINCTRL_ST
 	select PINCONF
 	select GPIOLIB_IRQCHIP
 
+config PINCTRL_STARFIVE
+	tristate "Pinctrl and GPIO driver for the StarFive JH7100 SoC"
+	depends on SOC_STARFIVE || COMPILE_TEST
+	depends on OF
+	default SOC_STARFIVE
+	select GENERIC_PINCTRL_GROUPS
+	select GENERIC_PINMUX_FUNCTIONS
+	select GENERIC_PINCONF
+	select GPIOLIB
+	select GPIOLIB_IRQCHIP
+	select OF_GPIO
+	help
+	  Say yes here to support pin control on the StarFive JH7100 SoC.
+	  This also provides an interface to the GPIO pins not used by other
+	  peripherals supporting inputs, outputs, configuring pull-up/pull-down
+	  and interrupts on input changes.
+
 config PINCTRL_STMFX
 	tristate "STMicroelectronics STMFX GPIO expander pinctrl driver"
 	depends on I2C

drivers/pinctrl/Makefile

@@ -39,6 +39,7 @@ obj-$(CONFIG_PINCTRL_LANTIQ)	+= pinctrl-lantiq.o
 obj-$(CONFIG_PINCTRL_LPC18XX)	+= pinctrl-lpc18xx.o
 obj-$(CONFIG_PINCTRL_TB10X)	+= pinctrl-tb10x.o
 obj-$(CONFIG_PINCTRL_ST) 	+= pinctrl-st.o
+obj-$(CONFIG_PINCTRL_STARFIVE)	+= pinctrl-starfive.o
 obj-$(CONFIG_PINCTRL_STMFX) 	+= pinctrl-stmfx.o
 obj-$(CONFIG_PINCTRL_ZYNQ)	+= pinctrl-zynq.o
 obj-$(CONFIG_PINCTRL_ZYNQMP)	+= pinctrl-zynqmp.o

drivers/reset/Kconfig

@@ -224,6 +224,13 @@ config RESET_SOCFPGA
 	  This enables the reset driver for the SoCFPGA ARMv7 platforms. This
 	  driver gets initialized early during platform init calls.
 
+config RESET_STARFIVE_JH7100
+	bool "StarFive JH7100 Reset Driver"
+	depends on SOC_STARFIVE || COMPILE_TEST
+	default SOC_STARFIVE
+	help
+	  This enables the reset controller driver for the StarFive JH7100 SoC.
+
 config RESET_SUNXI
 	bool "Allwinner SoCs Reset Driver" if COMPILE_TEST && !ARCH_SUNXI
 	default ARCH_SUNXI

drivers/reset/Makefile

@@ -29,6 +29,7 @@ obj-$(CONFIG_RESET_RZG2L_USBPHY_CTRL) += reset-rzg2l-usbphy-ctrl.o
 obj-$(CONFIG_RESET_SCMI) += reset-scmi.o
 obj-$(CONFIG_RESET_SIMPLE) += reset-simple.o
 obj-$(CONFIG_RESET_SOCFPGA) += reset-socfpga.o
+obj-$(CONFIG_RESET_STARFIVE_JH7100) += reset-starfive-jh7100.o
 obj-$(CONFIG_RESET_SUNXI) += reset-sunxi.o
 obj-$(CONFIG_RESET_TI_SCI) += reset-ti-sci.o
 obj-$(CONFIG_RESET_TI_SYSCON) += reset-ti-syscon.o

drivers/reset/reset-starfive-jh7100.c

+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Reset driver for the StarFive JH7100 SoC
+ *
+ * Copyright (C) 2021 Emil Renner Berthing <kernel@esmil.dk>
+ */
+
+#include <linux/bitmap.h>
+#include <linux/io.h>
+#include <linux/io-64-nonatomic-lo-hi.h>
+#include <linux/iopoll.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/reset-controller.h>
+#include <linux/spinlock.h>
+
+#include <dt-bindings/reset/starfive-jh7100.h>
+
+/* register offsets */
+#define JH7100_RESET_ASSERT0	0x00
+#define JH7100_RESET_ASSERT1	0x04
+#define JH7100_RESET_ASSERT2	0x08
+#define JH7100_RESET_ASSERT3	0x0c
+#define JH7100_RESET_STATUS0	0x10
+#define JH7100_RESET_STATUS1	0x14
+#define JH7100_RESET_STATUS2	0x18
+#define JH7100_RESET_STATUS3	0x1c
+
+/*
+ * Writing a 1 to the n'th bit of the m'th ASSERT register asserts
+ * line 32m + n, and writing a 0 deasserts the same line.
+ * Most reset lines have their status inverted so a 0 bit in the STATUS
+ * register means the line is asserted and a 1 means it's deasserted. A few
+ * lines don't though, so store the expected value of the status registers when
+ * all lines are asserted.
+ */
+static const u64 jh7100_reset_asserted[2] = {
+	/* STATUS0 */
+	BIT_ULL_MASK(JH7100_RST_U74) |
+	BIT_ULL_MASK(JH7100_RST_VP6_DRESET) |
+	BIT_ULL_MASK(JH7100_RST_VP6_BRESET) |
+	/* STATUS1 */
+	BIT_ULL_MASK(JH7100_RST_HIFI4_DRESET) |
+	BIT_ULL_MASK(JH7100_RST_HIFI4_BRESET),
+	/* STATUS2 */
+	BIT_ULL_MASK(JH7100_RST_E24) |
+	/* STATUS3 */
+	0,
+};
+
+struct jh7100_reset {
+	struct reset_controller_dev rcdev;
+	/* protect registers against concurrent read-modify-write */
+	spinlock_t lock;
+	void __iomem *base;
+};
+
+static inline struct jh7100_reset *
+jh7100_reset_from(struct reset_controller_dev *rcdev)
+{
+	return container_of(rcdev, struct jh7100_reset, rcdev);
+}
+
+static int jh7100_reset_update(struct reset_controller_dev *rcdev,
+			       unsigned long id, bool assert)
+{
+	struct jh7100_reset *data = jh7100_reset_from(rcdev);
+	unsigned long offset = BIT_ULL_WORD(id);
+	u64 mask = BIT_ULL_MASK(id);
+	void __iomem *reg_assert = data->base + JH7100_RESET_ASSERT0 + offset * sizeof(u64);
+	void __iomem *reg_status = data->base + JH7100_RESET_STATUS0 + offset * sizeof(u64);
+	u64 done = jh7100_reset_asserted[offset] & mask;
+	u64 value;
+	unsigned long flags;
+	int ret;
+
+	if (!assert)
+		done ^= mask;
+
+	spin_lock_irqsave(&data->lock, flags);
+
+	value = readq(reg_assert);
+	if (assert)
+		value |= mask;
+	else
+		value &= ~mask;
+	writeq(value, reg_assert);
+
+	/* if the associated clock is gated, deasserting might otherwise hang forever */
+	ret = readq_poll_timeout_atomic(reg_status, value, (value & mask) == done, 0, 1000);
+
+	spin_unlock_irqrestore(&data->lock, flags);
+	return ret;
+}
+
+static int jh7100_reset_assert(struct reset_controller_dev *rcdev,
+			       unsigned long id)
+{
+	return jh7100_reset_update(rcdev, id, true);
+}
+
+static int jh7100_reset_deassert(struct reset_controller_dev *rcdev,
+				 unsigned long id)
+{
+	return jh7100_reset_update(rcdev, id, false);
+}
+
+static int jh7100_reset_reset(struct reset_controller_dev *rcdev,
+			      unsigned long id)
+{
+	int ret;
+
+	ret = jh7100_reset_assert(rcdev, id);
+	if (ret)
+		return ret;
+
+	return jh7100_reset_deassert(rcdev, id);
+}
+
+static int jh7100_reset_status(struct reset_controller_dev *rcdev,
+			       unsigned long id)
+{
+	struct jh7100_reset *data = jh7100_reset_from(rcdev);
+	unsigned long offset = BIT_ULL_WORD(id);
+	u64 mask = BIT_ULL_MASK(id);
+	void __iomem *reg_status = data->base + JH7100_RESET_STATUS0 + offset * sizeof(u64);
+	u64 value = readq(reg_status);
+
+	return !((value ^ jh7100_reset_asserted[offset]) & mask);
+}
+
+static const struct reset_control_ops jh7100_reset_ops = {
+	.assert		= jh7100_reset_assert,
+	.deassert	= jh7100_reset_deassert,
+	.reset		= jh7100_reset_reset,
+	.status		= jh7100_reset_status,
+};
+
+static int __init jh7100_reset_probe(struct platform_device *pdev)
+{
+	struct jh7100_reset *data;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(data->base))
+		return PTR_ERR(data->base);
+
+	data->rcdev.ops = &jh7100_reset_ops;
+	data->rcdev.owner = THIS_MODULE;
+	data->rcdev.nr_resets = JH7100_RSTN_END;
+	data->rcdev.dev = &pdev->dev;
+	data->rcdev.of_node = pdev->dev.of_node;
+	spin_lock_init(&data->lock);
+
+	return devm_reset_controller_register(&pdev->dev, &data->rcdev);
+}
+
+static const struct of_device_id jh7100_reset_dt_ids[] = {
+	{ .compatible = "starfive,jh7100-reset" },
+	{ /* sentinel */ }
+};
+
+static struct platform_driver jh7100_reset_driver = {
+	.driver = {
+		.name = "jh7100-reset",
+		.of_match_table = jh7100_reset_dt_ids,
+		.suppress_bind_attrs = true,
+	},
+};
+builtin_platform_driver_probe(jh7100_reset_driver, jh7100_reset_probe);

drivers/tty/serial/8250/8250_dw.c

@@ -414,6 +414,8 @@ static void dw8250_quirks(struct uart_port *p, struct dw8250_data *data)
 
 		if (of_device_is_compatible(np, "marvell,armada-38x-uart"))
 			p->serial_out = dw8250_serial_out38x;
+		if (of_device_is_compatible(np, "starfive,jh7100-uart"))
+			p->set_termios = dw8250_do_set_termios;
 
 	} else if (acpi_dev_present("APMC0D08", NULL, -1)) {
 		p->iotype = UPIO_MEM32;
@@ -696,6 +698,7 @@ static const struct of_device_id dw8250_of_match[] = {
 	{ .compatible = "cavium,octeon-3860-uart" },
 	{ .compatible = "marvell,armada-38x-uart" },
 	{ .compatible = "renesas,rzn1-uart" },
+	{ .compatible = "starfive,jh7100-uart" },
 	{ /* Sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, dw8250_of_match);

include/dt-bindings/clock/starfive-jh7100.h

+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/*
+ * Copyright (C) 2021 Ahmad Fatoum, Pengutronix
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_STARFIVE_JH7100_H__
+#define __DT_BINDINGS_CLOCK_STARFIVE_JH7100_H__
+
+#define JH7100_CLK_CPUNDBUS_ROOT	0
+#define JH7100_CLK_DLA_ROOT		1
+#define JH7100_CLK_DSP_ROOT		2
+#define JH7100_CLK_GMACUSB_ROOT		3
+#define JH7100_CLK_PERH0_ROOT		4
+#define JH7100_CLK_PERH1_ROOT		5
+#define JH7100_CLK_VIN_ROOT		6
+#define JH7100_CLK_VOUT_ROOT		7
+#define JH7100_CLK_AUDIO_ROOT		8
+#define JH7100_CLK_CDECHIFI4_ROOT	9
+#define JH7100_CLK_CDEC_ROOT		10
+#define JH7100_CLK_VOUTBUS_ROOT		11
+#define JH7100_CLK_CPUNBUS_ROOT_DIV	12
+#define JH7100_CLK_DSP_ROOT_DIV		13
+#define JH7100_CLK_PERH0_SRC		14
+#define JH7100_CLK_PERH1_SRC		15
+#define JH7100_CLK_PLL0_TESTOUT		16
+#define JH7100_CLK_PLL1_TESTOUT		17
+#define JH7100_CLK_PLL2_TESTOUT		18
+#define JH7100_CLK_PLL2_REF		19
+#define JH7100_CLK_CPU_CORE		20
+#define JH7100_CLK_CPU_AXI		21
+#define JH7100_CLK_AHB_BUS		22
+#define JH7100_CLK_APB1_BUS		23
+#define JH7100_CLK_APB2_BUS		24
+#define JH7100_CLK_DOM3AHB_BUS		25
+#define JH7100_CLK_DOM7AHB_BUS		26
+#define JH7100_CLK_U74_CORE0		27
+#define JH7100_CLK_U74_CORE1		28
+#define JH7100_CLK_U74_AXI		29
+#define JH7100_CLK_U74RTC_TOGGLE	30
+#define JH7100_CLK_SGDMA2P_AXI		31
+#define JH7100_CLK_DMA2PNOC_AXI		32
+#define JH7100_CLK_SGDMA2P_AHB		33
+#define JH7100_CLK_DLA_BUS		34
+#define JH7100_CLK_DLA_AXI		35
+#define JH7100_CLK_DLANOC_AXI		36
+#define JH7100_CLK_DLA_APB		37
+#define JH7100_CLK_VP6_CORE		38
+#define JH7100_CLK_VP6BUS_SRC		39
+#define JH7100_CLK_VP6_AXI		40
+#define JH7100_CLK_VCDECBUS_SRC		41
+#define JH7100_CLK_VDEC_BUS		42
+#define JH7100_CLK_VDEC_AXI		43
+#define JH7100_CLK_VDECBRG_MAIN		44
+#define JH7100_CLK_VDEC_BCLK		45
+#define JH7100_CLK_VDEC_CCLK		46
+#define JH7100_CLK_VDEC_APB		47
+#define JH7100_CLK_JPEG_AXI		48
+#define JH7100_CLK_JPEG_CCLK		49
+#define JH7100_CLK_JPEG_APB		50
+#define JH7100_CLK_GC300_2X		51
+#define JH7100_CLK_GC300_AHB		52
+#define JH7100_CLK_JPCGC300_AXIBUS	53
+#define JH7100_CLK_GC300_AXI		54
+#define JH7100_CLK_JPCGC300_MAIN	55
+#define JH7100_CLK_VENC_BUS		56
+#define JH7100_CLK_VENC_AXI		57
+#define JH7100_CLK_VENCBRG_MAIN		58
+#define JH7100_CLK_VENC_BCLK		59
+#define JH7100_CLK_VENC_CCLK		60
+#define JH7100_CLK_VENC_APB		61
+#define JH7100_CLK_DDRPLL_DIV2		62
+#define JH7100_CLK_DDRPLL_DIV4		63
+#define JH7100_CLK_DDRPLL_DIV8		64
+#define JH7100_CLK_DDROSC_DIV2		65
+#define JH7100_CLK_DDRC0		66
+#define JH7100_CLK_DDRC1		67
+#define JH7100_CLK_DDRPHY_APB		68
+#define JH7100_CLK_NOC_ROB		69
+#define JH7100_CLK_NOC_COG		70
+#define JH7100_CLK_NNE_AHB		71
+#define JH7100_CLK_NNEBUS_SRC1		72
+#define JH7100_CLK_NNE_BUS		73
+#define JH7100_CLK_NNE_AXI		74
+#define JH7100_CLK_NNENOC_AXI		75
+#define JH7100_CLK_DLASLV_AXI		76
+#define JH7100_CLK_DSPX2C_AXI		77
+#define JH7100_CLK_HIFI4_SRC		78
+#define JH7100_CLK_HIFI4_COREFREE	79
+#define JH7100_CLK_HIFI4_CORE		80
+#define JH7100_CLK_HIFI4_BUS		81
+#define JH7100_CLK_HIFI4_AXI		82
+#define JH7100_CLK_HIFI4NOC_AXI		83
+#define JH7100_CLK_SGDMA1P_BUS		84
+#define JH7100_CLK_SGDMA1P_AXI		85
+#define JH7100_CLK_DMA1P_AXI		86
+#define JH7100_CLK_X2C_AXI		87
+#define JH7100_CLK_USB_BUS		88
+#define JH7100_CLK_USB_AXI		89
+#define JH7100_CLK_USBNOC_AXI		90
+#define JH7100_CLK_USBPHY_ROOTDIV	91
+#define JH7100_CLK_USBPHY_125M		92
+#define JH7100_CLK_USBPHY_PLLDIV25M	93
+#define JH7100_CLK_USBPHY_25M		94
+#define JH7100_CLK_AUDIO_DIV		95
+#define JH7100_CLK_AUDIO_SRC		96
+#define JH7100_CLK_AUDIO_12288		97
+#define JH7100_CLK_VIN_SRC		98
+#define JH7100_CLK_ISP0_BUS		99
+#define JH7100_CLK_ISP0_AXI		100
+#define JH7100_CLK_ISP0NOC_AXI		101
+#define JH7100_CLK_ISPSLV_AXI		102
+#define JH7100_CLK_ISP1_BUS		103
+#define JH7100_CLK_ISP1_AXI		104
+#define JH7100_CLK_ISP1NOC_AXI		105
+#define JH7100_CLK_VIN_BUS		106
+#define JH7100_CLK_VIN_AXI		107
+#define JH7100_CLK_VINNOC_AXI		108
+#define JH7100_CLK_VOUT_SRC		109
+#define JH7100_CLK_DISPBUS_SRC		110
+#define JH7100_CLK_DISP_BUS		111
+#define JH7100_CLK_DISP_AXI		112
+#define JH7100_CLK_DISPNOC_AXI		113
+#define JH7100_CLK_SDIO0_AHB		114
+#define JH7100_CLK_SDIO0_CCLKINT	115
+#define JH7100_CLK_SDIO0_CCLKINT_INV	116
+#define JH7100_CLK_SDIO1_AHB		117
+#define JH7100_CLK_SDIO1_CCLKINT	118
+#define JH7100_CLK_SDIO1_CCLKINT_INV	119
+#define JH7100_CLK_GMAC_AHB		120
+#define JH7100_CLK_GMAC_ROOT_DIV	121
+#define JH7100_CLK_GMAC_PTP_REF		122
+#define JH7100_CLK_GMAC_GTX		123
+#define JH7100_CLK_GMAC_RMII_TX		124
+#define JH7100_CLK_GMAC_RMII_RX		125
+#define JH7100_CLK_GMAC_TX		126
+#define JH7100_CLK_GMAC_TX_INV		127
+#define JH7100_CLK_GMAC_RX_PRE		128
+#define JH7100_CLK_GMAC_RX_INV		129
+#define JH7100_CLK_GMAC_RMII		130
+#define JH7100_CLK_GMAC_TOPHYREF	131
+#define JH7100_CLK_SPI2AHB_AHB		132
+#define JH7100_CLK_SPI2AHB_CORE		133
+#define JH7100_CLK_EZMASTER_AHB		134
+#define JH7100_CLK_E24_AHB		135
+#define JH7100_CLK_E24RTC_TOGGLE	136
+#define JH7100_CLK_QSPI_AHB		137
+#define JH7100_CLK_QSPI_APB		138
+#define JH7100_CLK_QSPI_REF		139
+#define JH7100_CLK_SEC_AHB		140
+#define JH7100_CLK_AES			141
+#define JH7100_CLK_SHA			142
+#define JH7100_CLK_PKA			143
+#define JH7100_CLK_TRNG_APB		144
+#define JH7100_CLK_OTP_APB		145
+#define JH7100_CLK_UART0_APB		146
+#define JH7100_CLK_UART0_CORE		147
+#define JH7100_CLK_UART1_APB		148
+#define JH7100_CLK_UART1_CORE		149
+#define JH7100_CLK_SPI0_APB		150
+#define JH7100_CLK_SPI0_CORE		151
+#define JH7100_CLK_SPI1_APB		152
+#define JH7100_CLK_SPI1_CORE		153
+#define JH7100_CLK_I2C0_APB		154
+#define JH7100_CLK_I2C0_CORE		155
+#define JH7100_CLK_I2C1_APB		156
+#define JH7100_CLK_I2C1_CORE		157
+#define JH7100_CLK_GPIO_APB		158
+#define JH7100_CLK_UART2_APB		159
+#define JH7100_CLK_UART2_CORE		160
+#define JH7100_CLK_UART3_APB		161
+#define JH7100_CLK_UART3_CORE		162
+#define JH7100_CLK_SPI2_APB		163
+#define JH7100_CLK_SPI2_CORE		164
+#define JH7100_CLK_SPI3_APB		165
+#define JH7100_CLK_SPI3_CORE		166
+#define JH7100_CLK_I2C2_APB		167
+#define JH7100_CLK_I2C2_CORE		168
+#define JH7100_CLK_I2C3_APB		169
+#define JH7100_CLK_I2C3_CORE		170
+#define JH7100_CLK_WDTIMER_APB		171
+#define JH7100_CLK_WDT_CORE		172
+#define JH7100_CLK_TIMER0_CORE		173
+#define JH7100_CLK_TIMER1_CORE		174
+#define JH7100_CLK_TIMER2_CORE		175
+#define JH7100_CLK_TIMER3_CORE		176
+#define JH7100_CLK_TIMER4_CORE		177
+#define JH7100_CLK_TIMER5_CORE		178
+#define JH7100_CLK_TIMER6_CORE		179
+#define JH7100_CLK_VP6INTC_APB		180
+#define JH7100_CLK_PWM_APB		181
+#define JH7100_CLK_MSI_APB		182
+#define JH7100_CLK_TEMP_APB		183
+#define JH7100_CLK_TEMP_SENSE		184
+#define JH7100_CLK_SYSERR_APB		185
+
+#define JH7100_CLK_PLL0_OUT		186
+#define JH7100_CLK_PLL1_OUT		187
+#define JH7100_CLK_PLL2_OUT		188
+
+#define JH7100_CLK_END			189
+
+#endif /* __DT_BINDINGS_CLOCK_STARFIVE_JH7100_H__ */

include/dt-bindings/reset/starfive-jh7100.h

+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/*
+ * Copyright (C) 2021 Ahmad Fatoum, Pengutronix
+ */
+
+#ifndef __DT_BINDINGS_RESET_STARFIVE_JH7100_H__
+#define __DT_BINDINGS_RESET_STARFIVE_JH7100_H__
+
+#define JH7100_RSTN_DOM3AHB_BUS		0
+#define JH7100_RSTN_DOM7AHB_BUS		1
+#define JH7100_RST_U74			2
+#define JH7100_RSTN_U74_AXI		3
+#define JH7100_RSTN_SGDMA2P_AHB		4
+#define JH7100_RSTN_SGDMA2P_AXI		5
+#define JH7100_RSTN_DMA2PNOC_AXI	6
+#define JH7100_RSTN_DLA_AXI		7
+#define JH7100_RSTN_DLANOC_AXI		8
+#define JH7100_RSTN_DLA_APB		9
+#define JH7100_RST_VP6_DRESET		10
+#define JH7100_RST_VP6_BRESET		11
+#define JH7100_RSTN_VP6_AXI		12
+#define JH7100_RSTN_VDECBRG_MAIN	13
+#define JH7100_RSTN_VDEC_AXI		14
+#define JH7100_RSTN_VDEC_BCLK		15
+#define JH7100_RSTN_VDEC_CCLK		16
+#define JH7100_RSTN_VDEC_APB		17
+#define JH7100_RSTN_JPEG_AXI		18
+#define JH7100_RSTN_JPEG_CCLK		19
+#define JH7100_RSTN_JPEG_APB		20
+#define JH7100_RSTN_JPCGC300_MAIN	21
+#define JH7100_RSTN_GC300_2X		22
+#define JH7100_RSTN_GC300_AXI		23
+#define JH7100_RSTN_GC300_AHB		24
+#define JH7100_RSTN_VENC_AXI		25
+#define JH7100_RSTN_VENCBRG_MAIN	26
+#define JH7100_RSTN_VENC_BCLK		27
+#define JH7100_RSTN_VENC_CCLK		28
+#define JH7100_RSTN_VENC_APB		29
+#define JH7100_RSTN_DDRPHY_APB		30
+#define JH7100_RSTN_NOC_ROB		31
+#define JH7100_RSTN_NOC_COG		32
+#define JH7100_RSTN_HIFI4_AXI		33
+#define JH7100_RSTN_HIFI4NOC_AXI	34
+#define JH7100_RST_HIFI4_DRESET		35
+#define JH7100_RST_HIFI4_BRESET		36
+#define JH7100_RSTN_USB_AXI		37
+#define JH7100_RSTN_USBNOC_AXI		38
+#define JH7100_RSTN_SGDMA1P_AXI		39
+#define JH7100_RSTN_DMA1P_AXI		40
+#define JH7100_RSTN_X2C_AXI		41
+#define JH7100_RSTN_NNE_AHB		42
+#define JH7100_RSTN_NNE_AXI		43
+#define JH7100_RSTN_NNENOC_AXI		44
+#define JH7100_RSTN_DLASLV_AXI		45
+#define JH7100_RSTN_DSPX2C_AXI		46
+#define JH7100_RSTN_VIN_SRC		47
+#define JH7100_RSTN_ISPSLV_AXI		48
+#define JH7100_RSTN_VIN_AXI		49
+#define JH7100_RSTN_VINNOC_AXI		50
+#define JH7100_RSTN_ISP0_AXI		51
+#define JH7100_RSTN_ISP0NOC_AXI		52
+#define JH7100_RSTN_ISP1_AXI		53
+#define JH7100_RSTN_ISP1NOC_AXI		54
+#define JH7100_RSTN_VOUT_SRC		55
+#define JH7100_RSTN_DISP_AXI		56
+#define JH7100_RSTN_DISPNOC_AXI		57
+#define JH7100_RSTN_SDIO0_AHB		58
+#define JH7100_RSTN_SDIO1_AHB		59
+#define JH7100_RSTN_GMAC_AHB		60
+#define JH7100_RSTN_SPI2AHB_AHB		61
+#define JH7100_RSTN_SPI2AHB_CORE	62
+#define JH7100_RSTN_EZMASTER_AHB	63
+#define JH7100_RST_E24			64
+#define JH7100_RSTN_QSPI_AHB		65
+#define JH7100_RSTN_QSPI_CORE		66
+#define JH7100_RSTN_QSPI_APB		67
+#define JH7100_RSTN_SEC_AHB		68
+#define JH7100_RSTN_AES			69
+#define JH7100_RSTN_PKA			70
+#define JH7100_RSTN_SHA			71
+#define JH7100_RSTN_TRNG_APB		72
+#define JH7100_RSTN_OTP_APB		73
+#define JH7100_RSTN_UART0_APB		74
+#define JH7100_RSTN_UART0_CORE		75
+#define JH7100_RSTN_UART1_APB		76
+#define JH7100_RSTN_UART1_CORE		77
+#define JH7100_RSTN_SPI0_APB		78
+#define JH7100_RSTN_SPI0_CORE		79
+#define JH7100_RSTN_SPI1_APB		80
+#define JH7100_RSTN_SPI1_CORE		81
+#define JH7100_RSTN_I2C0_APB		82
+#define JH7100_RSTN_I2C0_CORE		83
+#define JH7100_RSTN_I2C1_APB		84
+#define JH7100_RSTN_I2C1_CORE		85
+#define JH7100_RSTN_GPIO_APB		86
+#define JH7100_RSTN_UART2_APB		87
+#define JH7100_RSTN_UART2_CORE		88
+#define JH7100_RSTN_UART3_APB		89
+#define JH7100_RSTN_UART3_CORE		90
+#define JH7100_RSTN_SPI2_APB		91
+#define JH7100_RSTN_SPI2_CORE		92
+#define JH7100_RSTN_SPI3_APB		93
+#define JH7100_RSTN_SPI3_CORE		94
+#define JH7100_RSTN_I2C2_APB		95
+#define JH7100_RSTN_I2C2_CORE		96
+#define JH7100_RSTN_I2C3_APB		97
+#define JH7100_RSTN_I2C3_CORE		98
+#define JH7100_RSTN_WDTIMER_APB		99
+#define JH7100_RSTN_WDT			100
+#define JH7100_RSTN_TIMER0		101
+#define JH7100_RSTN_TIMER1		102
+#define JH7100_RSTN_TIMER2		103
+#define JH7100_RSTN_TIMER3		104
+#define JH7100_RSTN_TIMER4		105
+#define JH7100_RSTN_TIMER5		106
+#define JH7100_RSTN_TIMER6		107
+#define JH7100_RSTN_VP6INTC_APB		108
+#define JH7100_RSTN_PWM_APB		109
+#define JH7100_RSTN_MSI_APB		110
+#define JH7100_RSTN_TEMP_APB		111
+#define JH7100_RSTN_TEMP_SENSE		112
+#define JH7100_RSTN_SYSERR_APB		113
+
+#define JH7100_RSTN_END			114
+
+#endif /* __DT_BINDINGS_RESET_STARFIVE_JH7100_H__ */