Commit bb4eecf2 authored by Baolin Wang's avatar Baolin Wang Committed by Ulf Hansson

mmc: Change the max discard sectors and erase response when HW busy detect

When mmc host HW supports busy signalling (using R1B as response), don't
use the host->max_busy_timeout as the limitation when deciding the max
discard sectors, which we inform the generic BLOCK layer about. Instead,
let's use at least one preferred erase size as the max discard sectors.

In cases when the host controller supports HW busy signalling and the
timeout for the erase operation doesn't exceed the max_busy_timeout, we
keep the R1B response, otherwise we prevent the host from doing HW busy
detection by converting to a R1 response.
Signed-off-by: default avatarBaolin Wang <baolin.wang@linaro.org>
Signed-off-by: default avatarUlf Hansson <ulf.hansson@linaro.org>
parent 95cc46fe
......@@ -2067,7 +2067,8 @@ static int mmc_do_erase(struct mmc_card *card, unsigned int from,
unsigned int to, unsigned int arg)
{
struct mmc_command cmd = {0};
unsigned int qty = 0;
unsigned int qty = 0, busy_timeout = 0;
bool use_r1b_resp = false;
unsigned long timeout;
int err;
......@@ -2135,8 +2136,22 @@ static int mmc_do_erase(struct mmc_card *card, unsigned int from,
memset(&cmd, 0, sizeof(struct mmc_command));
cmd.opcode = MMC_ERASE;
cmd.arg = arg;
cmd.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC;
cmd.busy_timeout = mmc_erase_timeout(card, arg, qty);
busy_timeout = mmc_erase_timeout(card, arg, qty);
/*
* If the host controller supports busy signalling and the timeout for
* the erase operation does not exceed the max_busy_timeout, we should
* use R1B response. Or we need to prevent the host from doing hw busy
* detection, which is done by converting to a R1 response instead.
*/
if (card->host->max_busy_timeout &&
busy_timeout > card->host->max_busy_timeout) {
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
} else {
cmd.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC;
cmd.busy_timeout = busy_timeout;
use_r1b_resp = true;
}
err = mmc_wait_for_cmd(card->host, &cmd, 0);
if (err) {
pr_err("mmc_erase: erase error %d, status %#x\n",
......@@ -2148,7 +2163,14 @@ static int mmc_do_erase(struct mmc_card *card, unsigned int from,
if (mmc_host_is_spi(card->host))
goto out;
timeout = jiffies + msecs_to_jiffies(MMC_CORE_TIMEOUT_MS);
/*
* In case of when R1B + MMC_CAP_WAIT_WHILE_BUSY is used, the polling
* shall be avoided.
*/
if ((card->host->caps & MMC_CAP_WAIT_WHILE_BUSY) && use_r1b_resp)
goto out;
timeout = jiffies + msecs_to_jiffies(busy_timeout);
do {
memset(&cmd, 0, sizeof(struct mmc_command));
cmd.opcode = MMC_SEND_STATUS;
......@@ -2328,23 +2350,41 @@ static unsigned int mmc_do_calc_max_discard(struct mmc_card *card,
unsigned int arg)
{
struct mmc_host *host = card->host;
unsigned int max_discard, x, y, qty = 0, max_qty, timeout;
unsigned int max_discard, x, y, qty = 0, max_qty, min_qty, timeout;
unsigned int last_timeout = 0;
if (card->erase_shift)
if (card->erase_shift) {
max_qty = UINT_MAX >> card->erase_shift;
else if (mmc_card_sd(card))
min_qty = card->pref_erase >> card->erase_shift;
} else if (mmc_card_sd(card)) {
max_qty = UINT_MAX;
else
min_qty = card->pref_erase;
} else {
max_qty = UINT_MAX / card->erase_size;
min_qty = card->pref_erase / card->erase_size;
}
/* Find the largest qty with an OK timeout */
/*
* We should not only use 'host->max_busy_timeout' as the limitation
* when deciding the max discard sectors. We should set a balance value
* to improve the erase speed, and it can not get too long timeout at
* the same time.
*
* Here we set 'card->pref_erase' as the minimal discard sectors no
* matter what size of 'host->max_busy_timeout', but if the
* 'host->max_busy_timeout' is large enough for more discard sectors,
* then we can continue to increase the max discard sectors until we
* get a balance value.
*/
do {
y = 0;
for (x = 1; x && x <= max_qty && max_qty - x >= qty; x <<= 1) {
timeout = mmc_erase_timeout(card, arg, qty + x);
if (timeout > host->max_busy_timeout)
if (qty + x > min_qty &&
timeout > host->max_busy_timeout)
break;
if (timeout < last_timeout)
break;
last_timeout = timeout;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment