Commit c145d5c6 authored by Rudolf Marek's avatar Rudolf Marek Committed by Jean Delvare

hwmon: (it87) Add support for the ITE IT8603E

Add support for IT8603E.

This closes bug #57861:
https://bugzilla.kernel.org/show_bug.cgi?id=57861

[JD: Fixes and clean-ups.]
Signed-off-by: default avatarRudolf Marek <r.marek@assembler.cz>
Signed-off-by: default avatarJean Delvare <khali@linux-fr.org>
parent d8ec26d7
......@@ -2,6 +2,10 @@ Kernel driver it87
==================
Supported chips:
* IT8603E
Prefix: 'it8603'
Addresses scanned: from Super I/O config space (8 I/O ports)
Datasheet: Not publicly available
* IT8705F
Prefix: 'it87'
Addresses scanned: from Super I/O config space (8 I/O ports)
......@@ -90,7 +94,7 @@ motherboard models.
Description
-----------
This driver implements support for the IT8705F, IT8712F, IT8716F,
This driver implements support for the IT8603E, IT8705F, IT8712F, IT8716F,
IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E, IT8771E, IT8772E,
IT8782F, IT8783E/F, and SiS950 chips.
......@@ -129,6 +133,10 @@ to userspace applications.
The IT8728F, IT8771E, and IT8772E are considered compatible with the IT8721F,
until a datasheet becomes available (hopefully.)
The IT8603E is a custom design, hardware monitoring part is similar to
IT8728F. It only supports 16-bit fan mode, the full speed mode of the
fan is not supported (value 0 of pwmX_enable).
Temperatures are measured in degrees Celsius. An alarm is triggered once
when the Overtemperature Shutdown limit is crossed.
......@@ -145,13 +153,16 @@ alarm is triggered if the voltage has crossed a programmable minimum or
maximum limit. Note that minimum in this case always means 'closest to
zero'; this is important for negative voltage measurements. All voltage
inputs can measure voltages between 0 and 4.08 volts, with a resolution of
0.016 volt (except IT8721F/IT8758E and IT8728F: 0.012 volt.) The battery
voltage in8 does not have limit registers.
On the IT8721F/IT8758E, IT8782F, and IT8783E/F, some voltage inputs are
internal and scaled inside the chip (in7 (optional for IT8782F and IT8783E/F),
in8 and optionally in3). The driver handles this transparently so user-space
doesn't have to care.
0.016 volt (except IT8603E, IT8721F/IT8758E and IT8728F: 0.012 volt.) The
battery voltage in8 does not have limit registers.
On the IT8603E, IT8721F/IT8758E, IT8782F, and IT8783E/F, some voltage inputs
are internal and scaled inside the chip:
* in3 (optional)
* in7 (optional for IT8782F and IT8783E/F)
* in8 (always)
* in9 (relevant for IT8603E only)
The driver handles this transparently so user-space doesn't have to care.
The VID lines (IT8712F/IT8716F/IT8718F/IT8720F) encode the core voltage value:
the voltage level your processor should work with. This is hardcoded by
......
......@@ -573,8 +573,8 @@ config SENSORS_IT87
help
If you say yes here you get support for ITE IT8705F, IT8712F,
IT8716F, IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E,
IT8771E, IT8772E, IT8782F, and IT8783E/F sensor chips, and the
SiS950 clone.
IT8771E, IT8772E, IT8782F, IT8783E/F and IT8603E sensor chips,
and the SiS950 clone.
This driver can also be built as a module. If so, the module
will be called it87.
......
......@@ -10,7 +10,8 @@
* This driver supports only the Environment Controller in the IT8705F and
* similar parts. The other devices are supported by different drivers.
*
* Supports: IT8705F Super I/O chip w/LPC interface
* Supports: IT8603E Super I/O chip w/LPC interface
* IT8705F Super I/O chip w/LPC interface
* IT8712F Super I/O chip w/LPC interface
* IT8716F Super I/O chip w/LPC interface
* IT8718F Super I/O chip w/LPC interface
......@@ -64,7 +65,7 @@
#define DRVNAME "it87"
enum chips { it87, it8712, it8716, it8718, it8720, it8721, it8728, it8771,
it8772, it8782, it8783 };
it8772, it8782, it8783, it8603 };
static unsigned short force_id;
module_param(force_id, ushort, 0);
......@@ -146,6 +147,7 @@ static inline void superio_exit(void)
#define IT8772E_DEVID 0x8772
#define IT8782F_DEVID 0x8782
#define IT8783E_DEVID 0x8783
#define IT8306E_DEVID 0x8603
#define IT87_ACT_REG 0x30
#define IT87_BASE_REG 0x60
......@@ -315,6 +317,12 @@ static const struct it87_devices it87_devices[] = {
| FEAT_TEMP_OLD_PECI,
.old_peci_mask = 0x4,
},
[it8603] = {
.name = "it8603",
.features = FEAT_NEWER_AUTOPWM | FEAT_12MV_ADC | FEAT_16BIT_FANS
| FEAT_TEMP_OFFSET | FEAT_TEMP_PECI,
.peci_mask = 0x07,
},
};
#define has_16bit_fans(data) ((data)->features & FEAT_16BIT_FANS)
......@@ -361,7 +369,7 @@ struct it87_data {
unsigned long last_updated; /* In jiffies */
u16 in_scaled; /* Internal voltage sensors are scaled */
u8 in[9][3]; /* [nr][0]=in, [1]=min, [2]=max */
u8 in[10][3]; /* [nr][0]=in, [1]=min, [2]=max */
u8 has_fan; /* Bitfield, fans enabled */
u16 fan[5][2]; /* Register values, [nr][0]=fan, [1]=min */
u8 has_temp; /* Bitfield, temp sensors enabled */
......@@ -578,6 +586,7 @@ static SENSOR_DEVICE_ATTR_2(in7_max, S_IRUGO | S_IWUSR, show_in, set_in,
7, 2);
static SENSOR_DEVICE_ATTR_2(in8_input, S_IRUGO, show_in, NULL, 8, 0);
static SENSOR_DEVICE_ATTR_2(in9_input, S_IRUGO, show_in, NULL, 9, 0);
/* 3 temperatures */
static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
......@@ -734,7 +743,7 @@ static int pwm_mode(const struct it87_data *data, int nr)
{
int ctrl = data->fan_main_ctrl & (1 << nr);
if (ctrl == 0) /* Full speed */
if (ctrl == 0 && data->type != it8603) /* Full speed */
return 0;
if (data->pwm_ctrl[nr] & 0x80) /* Automatic mode */
return 2;
......@@ -929,6 +938,10 @@ static ssize_t set_pwm_enable(struct device *dev,
return -EINVAL;
}
/* IT8603E does not have on/off mode */
if (val == 0 && data->type == it8603)
return -EINVAL;
mutex_lock(&data->update_lock);
if (val == 0) {
......@@ -948,10 +961,13 @@ static ssize_t set_pwm_enable(struct device *dev,
else /* Automatic mode */
data->pwm_ctrl[nr] = 0x80 | data->pwm_temp_map[nr];
it87_write_value(data, IT87_REG_PWM(nr), data->pwm_ctrl[nr]);
/* set SmartGuardian mode */
data->fan_main_ctrl |= (1 << nr);
it87_write_value(data, IT87_REG_FAN_MAIN_CTRL,
data->fan_main_ctrl);
if (data->type != it8603) {
/* set SmartGuardian mode */
data->fan_main_ctrl |= (1 << nr);
it87_write_value(data, IT87_REG_FAN_MAIN_CTRL,
data->fan_main_ctrl);
}
}
mutex_unlock(&data->update_lock);
......@@ -1415,6 +1431,8 @@ static ssize_t show_label(struct device *dev, struct device_attribute *attr,
static SENSOR_DEVICE_ATTR(in3_label, S_IRUGO, show_label, NULL, 0);
static SENSOR_DEVICE_ATTR(in7_label, S_IRUGO, show_label, NULL, 1);
static SENSOR_DEVICE_ATTR(in8_label, S_IRUGO, show_label, NULL, 2);
/* special AVCC3 IT8306E in9 */
static SENSOR_DEVICE_ATTR(in9_label, S_IRUGO, show_label, NULL, 0);
static ssize_t show_name(struct device *dev, struct device_attribute
*devattr, char *buf)
......@@ -1424,7 +1442,7 @@ static ssize_t show_name(struct device *dev, struct device_attribute
}
static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
static struct attribute *it87_attributes_in[9][5] = {
static struct attribute *it87_attributes_in[10][5] = {
{
&sensor_dev_attr_in0_input.dev_attr.attr,
&sensor_dev_attr_in0_min.dev_attr.attr,
......@@ -1476,9 +1494,12 @@ static struct attribute *it87_attributes_in[9][5] = {
}, {
&sensor_dev_attr_in8_input.dev_attr.attr,
NULL
}, {
&sensor_dev_attr_in9_input.dev_attr.attr,
NULL
} };
static const struct attribute_group it87_group_in[9] = {
static const struct attribute_group it87_group_in[10] = {
{ .attrs = it87_attributes_in[0] },
{ .attrs = it87_attributes_in[1] },
{ .attrs = it87_attributes_in[2] },
......@@ -1488,6 +1509,7 @@ static const struct attribute_group it87_group_in[9] = {
{ .attrs = it87_attributes_in[6] },
{ .attrs = it87_attributes_in[7] },
{ .attrs = it87_attributes_in[8] },
{ .attrs = it87_attributes_in[9] },
};
static struct attribute *it87_attributes_temp[3][6] = {
......@@ -1546,7 +1568,8 @@ static struct attribute *it87_attributes_in_beep[] = {
&sensor_dev_attr_in5_beep.dev_attr.attr,
&sensor_dev_attr_in6_beep.dev_attr.attr,
&sensor_dev_attr_in7_beep.dev_attr.attr,
NULL
NULL,
NULL,
};
static struct attribute *it87_attributes_temp_beep[] = {
......@@ -1685,6 +1708,7 @@ static struct attribute *it87_attributes_label[] = {
&sensor_dev_attr_in3_label.dev_attr.attr,
&sensor_dev_attr_in7_label.dev_attr.attr,
&sensor_dev_attr_in8_label.dev_attr.attr,
&sensor_dev_attr_in9_label.dev_attr.attr,
NULL
};
......@@ -1742,6 +1766,9 @@ static int __init it87_find(unsigned short *address,
case IT8783E_DEVID:
sio_data->type = it8783;
break;
case IT8306E_DEVID:
sio_data->type = it8603;
break;
case 0xffff: /* No device at all */
goto exit;
default:
......@@ -1763,11 +1790,15 @@ static int __init it87_find(unsigned short *address,
err = 0;
sio_data->revision = superio_inb(DEVREV) & 0x0f;
pr_info("Found IT%04xF chip at 0x%x, revision %d\n",
chip_type, *address, sio_data->revision);
pr_info("Found IT%04x%c chip at 0x%x, revision %d\n", chip_type,
chip_type == 0x8603 ? 'E' : 'F', *address,
sio_data->revision);
/* in8 (Vbat) is always internal */
sio_data->internal = (1 << 2);
/* Only the IT8603E has in9 */
if (sio_data->type != it8603)
sio_data->skip_in |= (1 << 9);
/* Read GPIO config and VID value from LDN 7 (GPIO) */
if (sio_data->type == it87) {
......@@ -1844,7 +1875,38 @@ static int __init it87_find(unsigned short *address,
sio_data->internal |= (1 << 1);
sio_data->beep_pin = superio_inb(IT87_SIO_BEEP_PIN_REG) & 0x3f;
} else if (sio_data->type == it8603) {
int reg27, reg29;
sio_data->skip_vid = 1; /* No VID */
superio_select(GPIO);
reg27 = superio_inb(IT87_SIO_GPIO3_REG);
/* Check if fan3 is there or not */
if (reg27 & (1 << 6))
sio_data->skip_pwm |= (1 << 2);
if (reg27 & (1 << 7))
sio_data->skip_fan |= (1 << 2);
/* Check if fan2 is there or not */
reg29 = superio_inb(IT87_SIO_GPIO5_REG);
if (reg29 & (1 << 1))
sio_data->skip_pwm |= (1 << 1);
if (reg29 & (1 << 2))
sio_data->skip_fan |= (1 << 1);
sio_data->skip_in |= (1 << 5); /* No VIN5 */
sio_data->skip_in |= (1 << 6); /* No VIN6 */
/* no fan4 */
sio_data->skip_pwm |= (1 << 3);
sio_data->skip_fan |= (1 << 3);
sio_data->internal |= (1 << 1); /* in7 is VSB */
sio_data->internal |= (1 << 3); /* in9 is AVCC */
sio_data->beep_pin = superio_inb(IT87_SIO_BEEP_PIN_REG) & 0x3f;
} else {
int reg;
bool uart6;
......@@ -1966,7 +2028,7 @@ static void it87_remove_files(struct device *dev)
int i;
sysfs_remove_group(&dev->kobj, &it87_group);
for (i = 0; i < 9; i++) {
for (i = 0; i < 10; i++) {
if (sio_data->skip_in & (1 << i))
continue;
sysfs_remove_group(&dev->kobj, &it87_group_in[i]);
......@@ -2080,6 +2142,8 @@ static int it87_probe(struct platform_device *pdev)
data->in_scaled |= (1 << 7); /* in7 is VSB */
if (sio_data->internal & (1 << 2))
data->in_scaled |= (1 << 8); /* in8 is Vbat */
if (sio_data->internal & (1 << 3))
data->in_scaled |= (1 << 9); /* in9 is AVCC */
} else if (sio_data->type == it8782 || sio_data->type == it8783) {
if (sio_data->internal & (1 << 0))
data->in_scaled |= (1 << 3); /* in3 is VCC5V */
......@@ -2102,7 +2166,7 @@ static int it87_probe(struct platform_device *pdev)
if (err)
return err;
for (i = 0; i < 9; i++) {
for (i = 0; i < 10; i++) {
if (sio_data->skip_in & (1 << i))
continue;
err = sysfs_create_group(&dev->kobj, &it87_group_in[i]);
......@@ -2202,7 +2266,7 @@ static int it87_probe(struct platform_device *pdev)
}
/* Export labels for internal sensors */
for (i = 0; i < 3; i++) {
for (i = 0; i < 4; i++) {
if (!(sio_data->internal & (1 << i)))
continue;
err = sysfs_create_file(&dev->kobj,
......@@ -2383,8 +2447,9 @@ static void it87_init_device(struct platform_device *pdev)
}
data->has_fan = (data->fan_main_ctrl >> 4) & 0x07;
/* Set tachometers to 16-bit mode if needed */
if (has_16bit_fans(data)) {
/* Set tachometers to 16-bit mode if needed, IT8603E (and IT8728F?)
* has it by default */
if (has_16bit_fans(data) && data->type != it8603) {
tmp = it87_read_value(data, IT87_REG_FAN_16BIT);
if (~tmp & 0x07 & data->has_fan) {
dev_dbg(&pdev->dev,
......@@ -2464,6 +2529,8 @@ static struct it87_data *it87_update_device(struct device *dev)
}
/* in8 (battery) has no limit registers */
data->in[8][0] = it87_read_value(data, IT87_REG_VIN(8));
if (data->type == it8603)
data->in[9][0] = it87_read_value(data, 0x2f);
for (i = 0; i < 5; i++) {
/* Skip disabled fans */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment