Merge tag 'riscv-dt-fixes-for-v6.6-rc3' of...

Merge tag 'riscv-dt-fixes-for-v6.6-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes

RISC-V Devicetree fixes for v6.6-rc3

Starfive:
A fix for the size of the NOR flash that was causing complaints from the
MTD subsystem during boot & two issues that a certain someone introduced
while resolving merge conflicts. Of the latter, one is a cosmetic
ordering change & the other lead to the usb controller being disabled.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

* tag 'riscv-dt-fixes-for-v6.6-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
  riscv: dts: starfive: visionfive 2: Fix uart0 pins sort order
  riscv: dts: starfive: visionfive 2: Enable usb0
  riscv: dts: starfive: fix NOR flash reserved-data partition size

Link: https://lore.kernel.org/r/20230916-previous-oversold-9d30891ac6cf@spudSigned-off-by: Arnd Bergmann <arnd@arndb.de>

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi

@@ -262,7 +262,7 @@ uboot@100000 {
 				reg = <0x100000 0x400000>;
 			};
 			reserved-data@600000 {
-				reg = <0x600000 0x1000000>;
+				reg = <0x600000 0xa00000>;
 			};
 		};
 	};
@@ -440,30 +440,6 @@ GPOEN_ENABLE,
 		};
 	};
 
-	uart0_pins: uart0-0 {
-		tx-pins {
-			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
-					     GPOEN_ENABLE,
-					     GPI_NONE)>;
-			bias-disable;
-			drive-strength = <12>;
-			input-disable;
-			input-schmitt-disable;
-			slew-rate = <0>;
-		};
-
-		rx-pins {
-			pinmux = <GPIOMUX(6, GPOUT_LOW,
-					     GPOEN_DISABLE,
-					     GPI_SYS_UART0_RX)>;
-			bias-disable; /* external pull-up */
-			drive-strength = <2>;
-			input-enable;
-			input-schmitt-enable;
-			slew-rate = <0>;
-		};
-	};
-
 	tdm_pins: tdm-0 {
 		tx-pins {
 			pinmux = <GPIOMUX(44, GPOUT_SYS_TDM_TXD,
@@ -497,6 +473,30 @@ GPOEN_DISABLE,
 			input-enable;
 		};
 	};
+
+	uart0_pins: uart0-0 {
+		tx-pins {
+			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
+					     GPOEN_ENABLE,
+					     GPI_NONE)>;
+			bias-disable;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		rx-pins {
+			pinmux = <GPIOMUX(6, GPOUT_LOW,
+					     GPOEN_DISABLE,
+					     GPI_SYS_UART0_RX)>;
+			bias-disable; /* external pull-up */
+			drive-strength = <2>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+	};
 };
 
 &tdm {
@@ -513,6 +513,7 @@ &uart0 {
 
 &usb0 {
 	dr_mode = "peripheral";
+	status = "okay";
 };
 
 &U74_1 {