Commit c5d38f08 authored by Jason Wang's avatar Jason Wang Committed by Sascha Hauer

mx31_3ds: revert 3ds debug board relate code

Because we add a 3ds debug board support in mxc level, we remove
those redundant codes from board level.
Signed-off-by: default avatarJason Wang <jason77.wang@gmail.com>
Signed-off-by: default avatarSascha Hauer <s.hauer@pengutronix.de>
parent fa94f8dc
......@@ -67,6 +67,7 @@ config MACH_MX31LITE
config MACH_MX31_3DS
bool "Support MX31PDK (3DS)"
select ARCH_MX31
select MXC_DEBUG_BOARD
select IMX_HAVE_PLATFORM_IMX_UART
select IMX_HAVE_PLATFORM_MXC_NAND
select IMX_HAVE_PLATFORM_SPI_IMX
......
......@@ -18,7 +18,6 @@
#include <linux/clk.h>
#include <linux/irq.h>
#include <linux/gpio.h>
#include <linux/smsc911x.h>
#include <linux/platform_device.h>
#include <linux/mfd/mc13783.h>
#include <linux/spi/spi.h>
......@@ -34,6 +33,7 @@
#include <asm/mach/map.h>
#include <mach/common.h>
#include <mach/iomux-mx3.h>
#include <mach/3ds_debugboard.h>
#include "devices-imx31.h"
#include "devices.h"
......@@ -253,174 +253,12 @@ static const struct imxuart_platform_data uart_pdata __initconst = {
.flags = IMXUART_HAVE_RTSCTS,
};
/*
* Support for the SMSC9217 on the Debug board.
*/
static struct smsc911x_platform_config smsc911x_config = {
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
.flags = SMSC911X_USE_16BIT | SMSC911X_FORCE_INTERNAL_PHY,
.phy_interface = PHY_INTERFACE_MODE_MII,
};
static struct resource smsc911x_resources[] = {
{
.start = LAN9217_BASE_ADDR,
.end = LAN9217_BASE_ADDR + 0xff,
.flags = IORESOURCE_MEM,
}, {
.start = EXPIO_INT_ENET,
.end = EXPIO_INT_ENET,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device smsc911x_device = {
.name = "smsc911x",
.id = -1,
.num_resources = ARRAY_SIZE(smsc911x_resources),
.resource = smsc911x_resources,
.dev = {
.platform_data = &smsc911x_config,
},
};
/*
* Routines for the CPLD on the debug board. It contains a CPLD handling
* LEDs, switches, interrupts for Ethernet.
*/
static void mx31_3ds_expio_irq_handler(uint32_t irq, struct irq_desc *desc)
{
uint32_t imr_val;
uint32_t int_valid;
uint32_t expio_irq;
imr_val = __raw_readw(CPLD_INT_MASK_REG);
int_valid = __raw_readw(CPLD_INT_STATUS_REG) & ~imr_val;
expio_irq = MXC_EXP_IO_BASE;
for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
if ((int_valid & 1) == 0)
continue;
generic_handle_irq(expio_irq);
}
}
/*
* Disable an expio pin's interrupt by setting the bit in the imr.
* @param irq an expio virtual irq number
*/
static void expio_mask_irq(uint32_t irq)
{
uint16_t reg;
uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
/* mask the interrupt */
reg = __raw_readw(CPLD_INT_MASK_REG);
reg |= 1 << expio;
__raw_writew(reg, CPLD_INT_MASK_REG);
}
/*
* Acknowledge an expanded io pin's interrupt by clearing the bit in the isr.
* @param irq an expanded io virtual irq number
*/
static void expio_ack_irq(uint32_t irq)
{
uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
/* clear the interrupt status */
__raw_writew(1 << expio, CPLD_INT_RESET_REG);
__raw_writew(0, CPLD_INT_RESET_REG);
/* mask the interrupt */
expio_mask_irq(irq);
}
/*
* Enable a expio pin's interrupt by clearing the bit in the imr.
* @param irq a expio virtual irq number
*/
static void expio_unmask_irq(uint32_t irq)
{
uint16_t reg;
uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
/* unmask the interrupt */
reg = __raw_readw(CPLD_INT_MASK_REG);
reg &= ~(1 << expio);
__raw_writew(reg, CPLD_INT_MASK_REG);
}
static struct irq_chip expio_irq_chip = {
.ack = expio_ack_irq,
.mask = expio_mask_irq,
.unmask = expio_unmask_irq,
};
static int __init mx31_3ds_init_expio(void)
{
int i;
int ret;
/* Check if there's a debug board connected */
if ((__raw_readw(CPLD_MAGIC_NUMBER1_REG) != 0xAAAA) ||
(__raw_readw(CPLD_MAGIC_NUMBER2_REG) != 0x5555) ||
(__raw_readw(CPLD_MAGIC_NUMBER3_REG) != 0xCAFE)) {
/* No Debug board found */
return -ENODEV;
}
pr_info("i.MX31 3DS Debug board detected, rev = 0x%04X\n",
__raw_readw(CPLD_CODE_VER_REG));
/*
* Configure INT line as GPIO input
*/
ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1), "sms9217-irq");
if (ret)
pr_warning("could not get LAN irq gpio\n");
else
gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
/* Disable the interrupts and clear the status */
__raw_writew(0, CPLD_INT_MASK_REG);
__raw_writew(0xFFFF, CPLD_INT_RESET_REG);
__raw_writew(0, CPLD_INT_RESET_REG);
__raw_writew(0x1F, CPLD_INT_MASK_REG);
for (i = MXC_EXP_IO_BASE;
i < (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES);
i++) {
set_irq_chip(i, &expio_irq_chip);
set_irq_handler(i, handle_level_irq);
set_irq_flags(i, IRQF_VALID);
}
set_irq_type(EXPIO_PARENT_INT, IRQ_TYPE_LEVEL_LOW);
set_irq_chained_handler(EXPIO_PARENT_INT, mx31_3ds_expio_irq_handler);
return 0;
}
/*
* This structure defines the MX31 memory map.
*/
static struct map_desc mx31_3ds_io_desc[] __initdata = {
{
.virtual = MX31_CS5_BASE_ADDR_VIRT,
.pfn = __phys_to_pfn(MX31_CS5_BASE_ADDR),
.length = MX31_CS5_SIZE,
.type = MT_DEVICE,
},
};
/*
* Set up static virtual mappings.
*/
static void __init mx31_3ds_map_io(void)
{
mx31_map_io();
iotable_init(mx31_3ds_io_desc, ARRAY_SIZE(mx31_3ds_io_desc));
}
/*!
......@@ -443,8 +281,9 @@ static void __init mxc_board_init(void)
mx31_3ds_usbotg_init();
mxc_register_device(&mxc_otg_udc_device, &usbotg_pdata);
if (!mx31_3ds_init_expio())
platform_device_register(&smsc911x_device);
if (!mxc_expio_init(CS5_BASE_ADDR, EXPIO_PARENT_INT))
printk(KERN_WARNING "Init of the debugboard failed, all "
"devices on the board are unusable.\n");
}
static void __init mx31_3ds_timer_init(void)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment