Documentation: perf: Indent filter options list of hisi-pcie-pmu

The "Filter options" list have a rather ugly indentation. Also, the first
paragraph after list name is rendered without separator (as continuation
from the name).

Align the list by indenting the list items and add a blank line
separator for each list name.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/20221117084136.53572-4-yangyicong@huawei.comSigned-off-by: Will Deacon <will@kernel.org>

Documentation/admin-guide/perf/hisi-pcie-pmu.rst

@@ -48,59 +48,65 @@ Filter options
 --------------
 
 1. Target filter
-PMU could only monitor the performance of traffic downstream target Root Ports
-or downstream target Endpoint. PCIe PMU driver support "port" and "bdf"
-interfaces for users, and these two interfaces aren't supported at the same
-time.
 
--port
-"port" filter can be used in all PCIe PMU events, target Root Port can be
-selected by configuring the 16-bits-bitmap "port". Multi ports can be selected
-for AP-layer-events, and only one port can be selected for TL/DL-layer-events.
+   PMU could only monitor the performance of traffic downstream target Root
+   Ports or downstream target Endpoint. PCIe PMU driver support "port" and
+   "bdf" interfaces for users, and these two interfaces aren't supported at the
+   same time.
 
-For example, if target Root Port is 0000:00:00.0 (x8 lanes), bit0 of bitmap
-should be set, port=0x1; if target Root Port is 0000:00:04.0 (x4 lanes),
-bit8 is set, port=0x100; if these two Root Ports are both monitored, port=0x101.
+   - port
 
-Example usage of perf::
+     "port" filter can be used in all PCIe PMU events, target Root Port can be
+     selected by configuring the 16-bits-bitmap "port". Multi ports can be
+     selected for AP-layer-events, and only one port can be selected for
+     TL/DL-layer-events.
 
-  $# perf stat -e hisi_pcie0_core0/rx_mwr_latency,port=0x1/ sleep 5
+     For example, if target Root Port is 0000:00:00.0 (x8 lanes), bit0 of
+     bitmap should be set, port=0x1; if target Root Port is 0000:00:04.0 (x4
+     lanes), bit8 is set, port=0x100; if these two Root Ports are both
+     monitored, port=0x101.
 
--bdf
+     Example usage of perf::
 
-"bdf" filter can only be used in bandwidth events, target Endpoint is selected
-by configuring BDF to "bdf". Counter only counts the bandwidth of message
-requested by target Endpoint.
+       $# perf stat -e hisi_pcie0_core0/rx_mwr_latency,port=0x1/ sleep 5
 
-For example, "bdf=0x3900" means BDF of target Endpoint is 0000:39:00.0.
+   - bdf
 
-Example usage of perf::
+     "bdf" filter can only be used in bandwidth events, target Endpoint is
+     selected by configuring BDF to "bdf". Counter only counts the bandwidth of
+     message requested by target Endpoint.
+
+     For example, "bdf=0x3900" means BDF of target Endpoint is 0000:39:00.0.
+
+     Example usage of perf::
 
-  $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,bdf=0x3900/ sleep 5
+       $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,bdf=0x3900/ sleep 5
 
 2. Trigger filter
-Event statistics start when the first time TLP length is greater/smaller
-than trigger condition. You can set the trigger condition by writing "trig_len",
-and set the trigger mode by writing "trig_mode". This filter can only be used
-in bandwidth events.
 
-For example, "trig_len=4" means trigger condition is 2^4 DW, "trig_mode=0"
-means statistics start when TLP length > trigger condition, "trig_mode=1"
-means start when TLP length < condition.
+   Event statistics start when the first time TLP length is greater/smaller
+   than trigger condition. You can set the trigger condition by writing
+   "trig_len", and set the trigger mode by writing "trig_mode". This filter can
+   only be used in bandwidth events.
 
-Example usage of perf::
+   For example, "trig_len=4" means trigger condition is 2^4 DW, "trig_mode=0"
+   means statistics start when TLP length > trigger condition, "trig_mode=1"
+   means start when TLP length < condition.
+
+   Example usage of perf::
 
-  $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,trig_len=0x4,trig_mode=1/ sleep 5
+     $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,trig_len=0x4,trig_mode=1/ sleep 5
 
 3. Threshold filter
-Counter counts when TLP length within the specified range. You can set the
-threshold by writing "thr_len", and set the threshold mode by writing
-"thr_mode". This filter can only be used in bandwidth events.
 
-For example, "thr_len=4" means threshold is 2^4 DW, "thr_mode=0" means
-counter counts when TLP length >= threshold, and "thr_mode=1" means counts
-when TLP length < threshold.
+   Counter counts when TLP length within the specified range. You can set the
+   threshold by writing "thr_len", and set the threshold mode by writing
+   "thr_mode". This filter can only be used in bandwidth events.
 
-Example usage of perf::
+   For example, "thr_len=4" means threshold is 2^4 DW, "thr_mode=0" means
+   counter counts when TLP length >= threshold, and "thr_mode=1" means counts
+   when TLP length < threshold.
+
+   Example usage of perf::
 
-  $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,thr_len=0x4,thr_mode=1/ sleep 5
+     $# perf stat -e hisi_pcie0_core0/rx_mrd_flux,thr_len=0x4,thr_mode=1/ sleep 5