Commit ca861dd0 authored by Martin Sperl's avatar Martin Sperl Committed by Mark Brown

spi: bcm2835: set up spi-mode before asserting cs-gpio

When using reverse polarity for clock (spi-cpol) on a device
the clock line gets altered after chip-select has been asserted
resulting in an additional clock beat, which confuses hardware.

This did not show when using native-CS, as the same register
is used to control cs as well as polarity, so the changes came
into effect at the same time. Unfortunately this is not true
with gpio-cs.

To avoid this situation this patch moves the setup of polarity
(spi-cpol and spi-cpha) outside of the chip-select into
prepare_message, which is run prior to asserting chip-select.

Also fixes resetting 3-wire mode after use of rx-mode, so that
a 3-Wire sequence TX, RX, TX works as well (right now it runs
TX, RX, RX instead)
Reported-by: default avatarNoralf Tronnes <noralf@tronnes.org>
Signed-off-by: default avatarMartin Sperl <kernel@martin.sperl.org>
Signed-off-by: default avatarMark Brown <broonie@kernel.org>
parent bc0195aa
......@@ -553,13 +553,11 @@ static int bcm2835_spi_transfer_one(struct spi_master *master,
spi_used_hz = cdiv ? (clk_hz / cdiv) : (clk_hz / 65536);
bcm2835_wr(bs, BCM2835_SPI_CLK, cdiv);
/* handle all the modes */
/* handle all the 3-wire mode */
if ((spi->mode & SPI_3WIRE) && (tfr->rx_buf))
cs |= BCM2835_SPI_CS_REN;
if (spi->mode & SPI_CPOL)
cs |= BCM2835_SPI_CS_CPOL;
if (spi->mode & SPI_CPHA)
cs |= BCM2835_SPI_CS_CPHA;
else
cs &= ~BCM2835_SPI_CS_REN;
/* for gpio_cs set dummy CS so that no HW-CS get changed
* we can not run this in bcm2835_spi_set_cs, as it does
......@@ -592,6 +590,25 @@ static int bcm2835_spi_transfer_one(struct spi_master *master,
return bcm2835_spi_transfer_one_irq(master, spi, tfr, cs);
}
static int bcm2835_spi_prepare_message(struct spi_master *master,
struct spi_message *msg)
{
struct spi_device *spi = msg->spi;
struct bcm2835_spi *bs = spi_master_get_devdata(master);
u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
cs &= ~(BCM2835_SPI_CS_CPOL | BCM2835_SPI_CS_CPHA);
if (spi->mode & SPI_CPOL)
cs |= BCM2835_SPI_CS_CPOL;
if (spi->mode & SPI_CPHA)
cs |= BCM2835_SPI_CS_CPHA;
bcm2835_wr(bs, BCM2835_SPI_CS, cs);
return 0;
}
static void bcm2835_spi_handle_err(struct spi_master *master,
struct spi_message *msg)
{
......@@ -739,6 +756,7 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
master->set_cs = bcm2835_spi_set_cs;
master->transfer_one = bcm2835_spi_transfer_one;
master->handle_err = bcm2835_spi_handle_err;
master->prepare_message = bcm2835_spi_prepare_message;
master->dev.of_node = pdev->dev.of_node;
bs = spi_master_get_devdata(master);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment