iio: adc: add support for Allwinner SoCs ADC

The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. This patch adds the ADC driver which is
based on the MFD for the same SoCs ADC.

This also registers the thermal adc channel in the iio map array so
iio_hwmon could use it without modifying the Device Tree. This registers
the driver in the thermal framework.

The thermal sensor requires the IP to be in touchscreen mode to return
correct values. Therefore, if the user is continuously reading the ADC
channel(s), the thermal framework in which the thermal sensor is
registered will switch the IP in touchscreen mode to get a temperature
value and requires a delay of 100ms (because of the mode switching),
then the ADC will switch back to ADC mode and requires also a delay of
100ms. If the ADC readings are critical to user and the SoC temperature
is not, this driver is capable of not registering the thermal sensor in
the thermal framework and thus, "quicken" the ADC readings.

This driver probes on three different platform_device_id to take into
account slight differences (registers bit and temperature computation)
between Allwinner SoCs ADCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

drivers/iio/adc/Kconfig

@@ -559,6 +559,23 @@ config STX104
 	  The base port addresses for the devices may be configured via the base
 	  array module parameter.
 
+config SUN4I_GPADC
+	tristate "Support for the Allwinner SoCs GPADC"
+	depends on IIO
+	depends on MFD_SUN4I_GPADC
+	help
+	  Say yes here to build support for Allwinner (A10, A13 and A31) SoCs
+	  GPADC. This ADC provides 4 channels which can be used as an ADC or as
+	  a touchscreen input and one channel for thermal sensor.
+
+	  The thermal sensor slows down ADC readings and can be disabled by
+	  disabling CONFIG_THERMAL_OF. However, the thermal sensor should be
+	  enabled by default since the SoC temperature is usually more critical
+	  than ADC readings.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called sun4i-gpadc-iio.
+
 config TI_ADC081C
 	tristate "Texas Instruments ADC081C/ADC101C/ADC121C family"
 	depends on I2C

drivers/iio/adc/Makefile

@@ -49,6 +49,7 @@ obj-$(CONFIG_RCAR_GYRO_ADC) += rcar-gyroadc.o
 obj-$(CONFIG_ROCKCHIP_SARADC) += rockchip_saradc.o
 obj-$(CONFIG_SPEAR_ADC) += spear_adc.o
 obj-$(CONFIG_STX104) += stx104.o
+obj-$(CONFIG_SUN4I_GPADC) += sun4i-gpadc-iio.o
 obj-$(CONFIG_STM32_ADC_CORE) += stm32-adc-core.o
 obj-$(CONFIG_STM32_ADC) += stm32-adc.o
 obj-$(CONFIG_TI_ADC081C) += ti-adc081c.o

include/linux/mfd/sun4i-gpadc.h

@@ -28,6 +28,7 @@
 #define SUN4I_GPADC_CTRL1_TP_MODE_EN			BIT(4)
 #define SUN4I_GPADC_CTRL1_TP_ADC_SELECT			BIT(3)
 #define SUN4I_GPADC_CTRL1_ADC_CHAN_SELECT(x)		(GENMASK(2, 0) & (x))
+#define SUN4I_GPADC_CTRL1_ADC_CHAN_MASK			GENMASK(2, 0)
 
 /* TP_CTRL1 bits for sun6i SOCs */
 #define SUN6I_GPADC_CTRL1_TOUCH_PAN_CALI_EN		BIT(7)
@@ -35,6 +36,7 @@
 #define SUN6I_GPADC_CTRL1_TP_MODE_EN			BIT(5)
 #define SUN6I_GPADC_CTRL1_TP_ADC_SELECT			BIT(4)
 #define SUN6I_GPADC_CTRL1_ADC_CHAN_SELECT(x)		(GENMASK(3, 0) & BIT(x))
+#define SUN6I_GPADC_CTRL1_ADC_CHAN_MASK			GENMASK(3, 0)
 
 #define SUN4I_GPADC_CTRL2				0x08