Commit d5e49036 authored by Mohamed Abbas's avatar Mohamed Abbas Committed by John W. Linville

iwlagn: fix agn rate scaling

    Rate scaling in agn can be broken because of these two problems
    1- the LQ command could not sent, we try to call LQ command before
       post association will be rejected, this will cause the driver to
       break in rs_tx_status reporting initial rate does not match.
    2- In rs_rate_init we can get a value of 12, rate 60, for
       last_txrate_idx, this rate only valid in SISO/MIMO mode only
Signed-off-by: default avatarMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: default avatarReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
parent b8d476c8
......@@ -836,6 +836,10 @@ static void rs_tx_status(void *priv_r, struct ieee80211_supported_band *sband,
(hw->wiphy->bands[priv->band]->bitrates[rs_index].bitrate !=
hw->wiphy->bands[info->band]->bitrates[info->status.rates[0].idx].bitrate)) {
IWL_DEBUG_RATE("initial rate does not match 0x%x\n", tx_rate);
/* the last LQ command could failed so the LQ in ucode not
* the same in driver sync up
*/
iwl_send_lq_cmd(priv, &lq_sta->lq, CMD_ASYNC);
goto out;
}
......@@ -2167,6 +2171,7 @@ static void rs_rate_init(void *priv_r, struct ieee80211_supported_band *sband,
struct iwl_priv *priv = (struct iwl_priv *)priv_r;
struct ieee80211_conf *conf = &priv->hw->conf;
struct iwl_lq_sta *lq_sta = priv_sta;
u16 mask_bit = 0;
lq_sta->flush_timer = 0;
lq_sta->supp_rates = sta->supp_rates[sband->band];
......@@ -2200,16 +2205,6 @@ static void rs_rate_init(void *priv_r, struct ieee80211_supported_band *sband,
priv->assoc_station_added = 1;
}
/* Find highest tx rate supported by hardware and destination station */
lq_sta->last_txrate_idx = 3;
for (i = 0; i < sband->n_bitrates; i++)
if (sta->supp_rates[sband->band] & BIT(i))
lq_sta->last_txrate_idx = i;
/* For MODE_IEEE80211A, skip over cck rates in global rate table */
if (sband->band == IEEE80211_BAND_5GHZ)
lq_sta->last_txrate_idx += IWL_FIRST_OFDM_RATE;
lq_sta->is_dup = 0;
lq_sta->is_green = rs_use_green(priv, conf);
lq_sta->active_legacy_rate = priv->active_rate & ~(0x1000);
......@@ -2248,6 +2243,17 @@ static void rs_rate_init(void *priv_r, struct ieee80211_supported_band *sband,
lq_sta->tx_agg_tid_en = IWL_AGG_ALL_TID;
lq_sta->drv = priv;
/* Find highest tx rate supported by hardware and destination station */
mask_bit = sta->supp_rates[sband->band] & lq_sta->active_legacy_rate;
lq_sta->last_txrate_idx = 3;
for (i = 0; i < sband->n_bitrates; i++)
if (mask_bit & BIT(i))
lq_sta->last_txrate_idx = i;
/* For MODE_IEEE80211A, skip over cck rates in global rate table */
if (sband->band == IEEE80211_BAND_5GHZ)
lq_sta->last_txrate_idx += IWL_FIRST_OFDM_RATE;
rs_initialize_lq(priv, conf, sta, lq_sta);
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment