Commit dc318756 authored by Frans Klaver's avatar Frans Klaver Committed by Greg Kroah-Hartman

tty: omap-serial: fix division by zero

If the chosen baud rate is large enough (e.g. 3.5 megabaud), the
calculated n values in serial_omap_is_baud_mode16() may become 0. This
causes a division by zero when calculating the difference between
calculated and desired baud rates. To prevent this, cap the n13 and n16
values on 1.

Division by zero in kernel.
[<c00132e0>] (unwind_backtrace) from [<c00112ec>] (show_stack+0x10/0x14)
[<c00112ec>] (show_stack) from [<c01ed7bc>] (Ldiv0+0x8/0x10)
[<c01ed7bc>] (Ldiv0) from [<c023805c>] (serial_omap_baud_is_mode16+0x4c/0x68)
[<c023805c>] (serial_omap_baud_is_mode16) from [<c02396b4>] (serial_omap_set_termios+0x90/0x8d8)
[<c02396b4>] (serial_omap_set_termios) from [<c0230a0c>] (uart_change_speed+0xa4/0xa8)
[<c0230a0c>] (uart_change_speed) from [<c0231798>] (uart_set_termios+0xa0/0x1fc)
[<c0231798>] (uart_set_termios) from [<c022bb44>] (tty_set_termios+0x248/0x2c0)
[<c022bb44>] (tty_set_termios) from [<c022c17c>] (set_termios+0x248/0x29c)
[<c022c17c>] (set_termios) from [<c022c3e4>] (tty_mode_ioctl+0x1c8/0x4e8)
[<c022c3e4>] (tty_mode_ioctl) from [<c0227e70>] (tty_ioctl+0xa94/0xb18)
[<c0227e70>] (tty_ioctl) from [<c00cf45c>] (do_vfs_ioctl+0x4a0/0x560)
[<c00cf45c>] (do_vfs_ioctl) from [<c00cf568>] (SyS_ioctl+0x4c/0x74)
[<c00cf568>] (SyS_ioctl) from [<c000e480>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: default avatarFrans Klaver <frans.klaver@xsens.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent fb498df0
......@@ -254,8 +254,16 @@ serial_omap_baud_is_mode16(struct uart_port *port, unsigned int baud)
{
unsigned int n13 = port->uartclk / (13 * baud);
unsigned int n16 = port->uartclk / (16 * baud);
int baudAbsDiff13 = baud - (port->uartclk / (13 * n13));
int baudAbsDiff16 = baud - (port->uartclk / (16 * n16));
int baudAbsDiff13;
int baudAbsDiff16;
if (n13 == 0)
n13 = 1;
if (n16 == 0)
n16 = 1;
baudAbsDiff13 = baud - (port->uartclk / (13 * n13));
baudAbsDiff16 = baud - (port->uartclk / (16 * n16));
if (baudAbsDiff13 < 0)
baudAbsDiff13 = -baudAbsDiff13;
if (baudAbsDiff16 < 0)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment