mtd: spi-nor: stm32: remove the driver as it was replaced by spi-stm32-qspi.c

There's a new driver using the SPI memory interface of the
SPI framework at spi/spi-stm32-qspi.c, which can be used
together with m25p80.c to replace the functionality of
this SPI NOR driver.

The "new" driver uses the same dt properties and not affects
the legacy compatibility.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>

Documentation/devicetree/bindings/mtd/stm32-quadspi.txt

-* STMicroelectronics Quad Serial Peripheral Interface(QuadSPI)
-
-Required properties:
-- compatible: should be "st,stm32f469-qspi"
-- reg: the first contains the register location and length.
-       the second contains the memory mapping address and length
-- reg-names: should contain the reg names "qspi" "qspi_mm"
-- interrupts: should contain the interrupt for the device
-- clocks: the phandle of the clock needed by the QSPI controller
-- A pinctrl must be defined to set pins in mode of operation for QSPI transfer
-
-Optional properties:
-- resets: must contain the phandle to the reset controller.
-
-A spi flash must be a child of the nor_flash node and could have some
-properties. Also see jedec,spi-nor.txt.
-
-Required properties:
-- reg: chip-Select number (QSPI controller may connect 2 nor flashes)
-- spi-max-frequency: max frequency of spi bus
-
-Optional property:
-- spi-rx-bus-width: see ../spi/spi-bus.txt for the description
-
-Example:
-
-qspi: spi@a0001000 {
-	compatible = "st,stm32f469-qspi";
-	reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>;
-	reg-names = "qspi", "qspi_mm";
-	interrupts = <91>;
-	resets = <&rcc STM32F4_AHB3_RESET(QSPI)>;
-	clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_qspi0>;
-
-	flash@0 {
-		reg = <0>;
-		spi-rx-bus-width = <4>;
-		spi-max-frequency = <108000000>;
-		...
-	};
-};

drivers/mtd/spi-nor/Kconfig

@@ -104,11 +104,4 @@ config SPI_INTEL_SPI_PLATFORM
 	  To compile this driver as a module, choose M here: the module
 	  will be called intel-spi-platform.
 
-config SPI_STM32_QUADSPI
-	tristate "STM32 Quad SPI controller"
-	depends on ARCH_STM32 || COMPILE_TEST
-	help
-	  This enables support for the STM32 Quad SPI controller.
-	  We only connect the NOR to this controller.
-
 endif # MTD_SPI_NOR

drivers/mtd/spi-nor/Makefile

@@ -8,4 +8,3 @@ obj-$(CONFIG_SPI_NXP_SPIFI)	+= nxp-spifi.o
 obj-$(CONFIG_SPI_INTEL_SPI)	+= intel-spi.o
 obj-$(CONFIG_SPI_INTEL_SPI_PCI)	+= intel-spi-pci.o
 obj-$(CONFIG_SPI_INTEL_SPI_PLATFORM)	+= intel-spi-platform.o
-obj-$(CONFIG_SPI_STM32_QUADSPI)	+= stm32-quadspi.o