arm64: dts: qcom: sm8150: Add base dts file

This add base DTS file with cpu, psci, firmware, clock node tlmm and
spmi and enables boot to console
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arch/arm64/boot/dts/qcom/sm8150.dtsi

+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <38400000>;
+			clock-output-names = "xo_board";
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32764>;
+			clock-output-names = "sleep_clk";
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+			L2_0: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+				L3_0: l3-cache {
+				      compatible = "cache";
+				};
+			};
+		};
+
+		CPU1: cpu@100 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&L2_100>;
+			L2_100: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+
+		};
+
+		CPU2: cpu@200 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x200>;
+			enable-method = "psci";
+			next-level-cache = <&L2_200>;
+			L2_200: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU3: cpu@300 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x300>;
+			enable-method = "psci";
+			next-level-cache = <&L2_300>;
+			L2_300: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU4: cpu@400 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x400>;
+			enable-method = "psci";
+			next-level-cache = <&L2_400>;
+			L2_400: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU5: cpu@500 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x500>;
+			enable-method = "psci";
+			next-level-cache = <&L2_500>;
+			L2_500: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU6: cpu@600 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x600>;
+			enable-method = "psci";
+			next-level-cache = <&L2_600>;
+			L2_600: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU7: cpu@700 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x700>;
+			enable-method = "psci";
+			next-level-cache = <&L2_700>;
+			L2_700: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-sm8150", "qcom,scm";
+			#reset-cells = <1>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0x0 0x80000000 0x0 0x0>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	soc: soc@0 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sm8150";
+			reg = <0x0 0x00100000 0x0 0x1f0000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clock-names = "bi_tcxo",
+				      "sleep_clk";
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&sleep_clk>;
+		};
+
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x00ac0000 0x0 0x6000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc 123>,
+				 <&gcc 124>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			uart2: serial@a90000 {
+				compatible = "qcom,geni-debug-uart";
+				reg = <0x0 0x00a90000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc 105>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		tlmm: pinctrl@3100000 {
+			compatible = "qcom,sm8150-pinctrl";
+			reg = <0x0 0x03100000 0x0 0x300000>,
+			      <0x0 0x03500000 0x0 0x300000>,
+			      <0x0 0x03900000 0x0 0x300000>,
+			      <0x0 0x03D00000 0x0 0x300000>;
+			reg-names = "west", "east", "north", "south";
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-ranges = <&tlmm 0 0 175>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		spmi_bus: spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x0 0x0c440000 0x0 0x0001100>,
+			      <0x0 0x0c600000 0x0 0x2000000>,
+			      <0x0 0x0e600000 0x0 0x0100000>,
+			      <0x0 0x0e700000 0x0 0x00a0000>,
+			      <0x0 0x0c40a000 0x0 0x0026000>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+			cell-index = <0>;
+		};
+
+		intc: interrupt-controller@17a00000 {
+			compatible = "arm,gic-v3";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x0 0x17a00000 0x0 0x10000>,	/* GICD */
+			      <0x0 0x17a60000 0x0 0x100000>;	/* GICR * 8 */
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		timer@17c20000 {
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x0 0x17c20000 0x0 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@17c21000{
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c21000 0x0 0x1000>,
+				      <0x0 0x17c22000 0x0 0x1000>;
+			};
+
+			frame@17c23000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c23000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c25000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c25000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c27000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c26000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c29000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c29000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2b000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c2b000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2d000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c2d000 0x0 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};