Merge tag 'phy-for-4.7' of...

Merge tag 'phy-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing

Kishon writes:

phy: for 4.7

*) Add a new PHY driver for USB2 PHY on Northstar SoC
*) Add support for Broadcom NS2 SATA3 PHY in existing
   Broadcom SATA3 PHY driver
*) Add support for MIPI DPHYs in Exynos5420-compatible
   (5420, 5422 and 5800) and Exynos5433 SoCs
*) Add support for USB3 PHY on mt2701
*) Add extcon support for Renesas R-car USB2 PHY driver
*) Misc cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.txt

+Driver for Broadcom Northstar USB 2.0 PHY
+
+Required properties:
+- compatible: brcm,ns-usb2-phy
+- reg: iomem address range of DMU (Device Management Unit)
+- reg-names: "dmu", the only needed & supported reg right now
+- clocks: USB PHY reference clock
+- clock-names: "phy-ref-clk", the only needed & supported clock right now
+
+To initialize USB 2.0 PHY driver needs to setup PLL correctly. To do this it
+requires passing phandle to the USB PHY reference clock.
+
+Example:
+	usb2-phy {
+		compatible = "brcm,ns-usb2-phy";
+		reg = <0x1800c000 0x1000>;
+		reg-names = "dmu";
+		#phy-cells = <0>;
+		clocks = <&genpll BCM_NSP_GENPLL_USB_PHY_REF_CLK>;
+		clock-names = "phy-ref-clk";
+	};

Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt → Documentation/devicetree/bindings/phy/brcm-sata-phy.txt

-* Broadcom SATA3 PHY for STB
+* Broadcom SATA3 PHY
 
 Required properties:
 - compatible: should be one or more of
      "brcm,bcm7425-sata-phy"
      "brcm,bcm7445-sata-phy"
+     "brcm,iproc-ns2-sata-phy"
      "brcm,phy-sata3"
 - address-cells: should be 1
 - size-cells: should be 0
-- reg: register range for the PHY PCB interface
-- reg-names: should be "phy"
+- reg: register ranges for the PHY PCB interface
+- reg-names: should be "phy" and "phy-ctrl"
+     The "phy-ctrl" registers are only required for
+     "brcm,iproc-ns2-sata-phy".
 
 Sub-nodes:
   Each port's PHY should be represented as a sub-node.
@@ -16,12 +19,12 @@ Sub-nodes:
 Sub-nodes required properties:
 - reg: the PHY number
 - phy-cells: generic PHY binding; must be 0
-Optional:
-- brcm,enable-ssc: use spread spectrum clocking (SSC) on this port
 
+Sub-nodes optional properties:
+- brcm,enable-ssc: use spread spectrum clocking (SSC) on this port
+     This property is not applicable for "brcm,iproc-ns2-sata-phy".
 
 Example:
-
 	sata-phy@f0458100 {
 		compatible = "brcm,bcm7445-sata-phy", "brcm,phy-sata3";
 		reg = <0xf0458100 0x1e00>, <0xf045804c 0x10>;

Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt

@@ -4,7 +4,9 @@ mt65xx USB3.0 PHY binding
 This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
 
 Required properties (controller (parent) node):
- - compatible	: should be "mediatek,mt8173-u3phy"
+ - compatible	: should be one of
+		  "mediatek,mt2701-u3phy"
+		  "mediatek,mt8173-u3phy"
  - reg		: offset and length of register for phy, exclude port's
 		  register.
  - clocks	: a list of phandle + clock-specifier pairs, one for each

Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt

@@ -7,6 +7,12 @@ Required properties:
 - compatible: "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC.
 	      "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC.
 	      "renesas,usb-phy-r8a7794" if the device is a part of R8A7794 SoC.
+	      "renesas,rcar-gen2-usb-phy" for a generic R-Car Gen2 compatible device.
+
+	      When compatible with the generic version, nodes must list the
+	      SoC-specific version corresponding to the platform first
+	      followed by the generic version.
+
 - reg: offset and length of the register block.
 - #address-cells: number of address cells for the USB channel subnodes, must
 		  be <1>.
@@ -34,7 +40,7 @@ the USB channel; see the selector meanings below:
 Example (Lager board):
 
 	usb-phy@e6590100 {
-		compatible = "renesas,usb-phy-r8a7790";
+		compatible = "renesas,usb-phy-r8a7790", "renesas,rcar-gen2-usb-phy";
 		reg = <0 0xe6590100 0 0x100>;
 		#address-cells = <1>;
 		#size-cells = <0>;

Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt

@@ -6,6 +6,12 @@ This file provides information on what the device node for the R-Car generation
 Required properties:
 - compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795
 	      SoC.
+	      "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 compatible device.
+
+	      When compatible with the generic version, nodes must list the
+	      SoC-specific version corresponding to the platform first
+	      followed by the generic version.
+
 - reg: offset and length of the partial USB 2.0 Host register block.
 - clocks: clock phandle and specifier pair(s).
 - #phy-cells: see phy-bindings.txt in the same directory, must be <0>.
@@ -15,18 +21,20 @@ To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are
 combined, the device tree node should set interrupt properties to use the
 channel as USB OTG:
 - interrupts: interrupt specifier for the PHY.
+- vbus-supply: Phandle to a regulator that provides power to the VBUS. This
+	       regulator will be managed during the PHY power on/off sequence.
 
 Example (R-Car H3):
 
 	usb-phy@ee080200 {
-		compatible = "renesas,usb2-phy-r8a7795";
+		compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy";
 		reg = <0 0xee080200 0 0x700>;
 		interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp7_clks R8A7795_CLK_EHCI0>;
 	};
 
 	usb-phy@ee0a0200 {
-		compatible = "renesas,usb2-phy-r8a7795";
+		compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy";
 		reg = <0 0xee0a0200 0 0x700>;
 		clocks = <&mstp7_clks R8A7795_CLK_EHCI0>;
 	};

Documentation/devicetree/bindings/phy/samsung-phy.txt

@@ -2,9 +2,20 @@ Samsung S5P/EXYNOS SoC series MIPI CSIS/DSIM DPHY
 -------------------------------------------------
 
 Required properties:
-- compatible : should be "samsung,s5pv210-mipi-video-phy";
+- compatible : should be one of the listed compatibles:
+	- "samsung,s5pv210-mipi-video-phy"
+	- "samsung,exynos5420-mipi-video-phy"
+	- "samsung,exynos5433-mipi-video-phy"
 - #phy-cells : from the generic phy bindings, must be 1;
-- syscon - phandle to the PMU system controller;
+
+In case of s5pv210 and exynos5420 compatible PHYs:
+- syscon - phandle to the PMU system controller
+
+In case of exynos5433 compatible PHY:
+ - samsung,pmu-syscon - phandle to the PMU system controller
+ - samsung,disp-sysreg - phandle to the DISP system registers controller
+ - samsung,cam0-sysreg - phandle to the CAM0 system registers controller
+ - samsung,cam1-sysreg - phandle to the CAM1 system registers controller
 
 For "samsung,s5pv210-mipi-video-phy" compatible PHYs the second cell in
 the PHY specifier identifies the PHY and its meaning is as follows:
@@ -12,6 +23,9 @@ the PHY specifier identifies the PHY and its meaning is as follows:
   1 - MIPI DSIM 0,
   2 - MIPI CSIS 1,
   3 - MIPI DSIM 1.
+"samsung,exynos5420-mipi-video-phy" and "samsung,exynos5433-mipi-video-phy"
+supports additional fifth PHY:
+  4 - MIPI CSIS 2.
 
 Samsung EXYNOS SoC series Display Port PHY
 -------------------------------------------------

drivers/phy/Kconfig

@@ -15,6 +15,15 @@ config GENERIC_PHY
 	  phy users can obtain reference to the PHY. All the users of this
 	  framework should select this config.
 
+config PHY_BCM_NS_USB2
+	tristate "Broadcom Northstar USB 2.0 PHY Driver"
+	depends on ARCH_BCM_IPROC || COMPILE_TEST
+	depends on HAS_IOMEM && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support Broadcom USB 2.0 PHY connected to the USB
+	  controller on Northstar family.
+
 config PHY_BERLIN_USB
 	tristate "Marvell Berlin USB PHY Driver"
 	depends on ARCH_BERLIN && RESET_CONTROLLER && HAS_IOMEM && OF
@@ -113,14 +122,15 @@ config PHY_MIPHY365X
 
 config PHY_RCAR_GEN2
 	tristate "Renesas R-Car generation 2 USB PHY driver"
-	depends on ARCH_SHMOBILE
+	depends on ARCH_RENESAS
 	depends on GENERIC_PHY
 	help
 	  Support for USB PHY found on Renesas R-Car generation 2 SoCs.
 
 config PHY_RCAR_GEN3_USB2
 	tristate "Renesas R-Car generation 3 USB 2.0 PHY driver"
-	depends on OF && ARCH_SHMOBILE
+	depends on ARCH_RENESAS
+	depends on EXTCON
 	select GENERIC_PHY
 	help
 	  Support for USB 2.0 PHY found on Renesas R-Car generation 3 SoCs.
@@ -218,9 +228,8 @@ config PHY_MT65XX_USB3
 	depends on ARCH_MEDIATEK && OF
 	select GENERIC_PHY
 	help
-	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
-	  for mt65xx SoCs. it supports two usb2.0 ports and
-	  one usb3.0 port.
+	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver,
+	  it supports multiple usb2.0 and usb3.0 ports.
 
 config PHY_HI6220_USB
 	tristate "hi6220 USB PHY support"
@@ -404,14 +413,15 @@ config PHY_TUSB1210
 	help
 	  Support for TI TUSB1210 USB ULPI PHY.
 
-config PHY_BRCMSTB_SATA
-	tristate "Broadcom STB SATA PHY driver"
-	depends on ARCH_BRCMSTB || BMIPS_GENERIC
+config PHY_BRCM_SATA
+	tristate "Broadcom SATA PHY driver"
+	depends on ARCH_BRCMSTB || ARCH_BCM_IPROC || BMIPS_GENERIC || COMPILE_TEST
 	depends on OF
 	select GENERIC_PHY
+	default ARCH_BCM_IPROC
 	help
-	  Enable this to support the SATA3 PHY on 28nm or 40nm Broadcom STB SoCs.
-	  Likely useful only with CONFIG_SATA_BRCMSTB enabled.
+	  Enable this to support the Broadcom SATA PHY.
+	  If unsure, say N.
 
 config PHY_CYGNUS_PCIE
 	tristate "Broadcom Cygnus PCIe PHY driver"

drivers/phy/Makefile

@@ -3,6 +3,7 @@
 #
 
 obj-$(CONFIG_GENERIC_PHY)		+= phy-core.o
+obj-$(CONFIG_PHY_BCM_NS_USB2)		+= phy-bcm-ns-usb2.o
 obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
 obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
 obj-$(CONFIG_PHY_DM816X_USB)		+= phy-dm816x-usb.o
@@ -49,6 +50,6 @@ obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-20nm.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-14nm.o
 obj-$(CONFIG_PHY_TUSB1210)		+= phy-tusb1210.o
-obj-$(CONFIG_PHY_BRCMSTB_SATA)		+= phy-brcmstb-sata.o
+obj-$(CONFIG_PHY_BRCM_SATA)		+= phy-brcm-sata.o
 obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
 obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o

drivers/phy/phy-bcm-ns-usb2.c

+/*
+ * Broadcom Northstar USB 2.0 PHY Driver
+ *
+ * Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/bcma/bcma.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+struct bcm_ns_usb2 {
+	struct device *dev;
+	struct clk *ref_clk;
+	struct phy *phy;
+	void __iomem *dmu;
+};
+
+static int bcm_ns_usb2_phy_init(struct phy *phy)
+{
+	struct bcm_ns_usb2 *usb2 = phy_get_drvdata(phy);
+	struct device *dev = usb2->dev;
+	void __iomem *dmu = usb2->dmu;
+	u32 ref_clk_rate, usb2ctl, usb_pll_ndiv, usb_pll_pdiv;
+	int err = 0;
+
+	err = clk_prepare_enable(usb2->ref_clk);
+	if (err < 0) {
+		dev_err(dev, "Failed to prepare ref clock: %d\n", err);
+		goto err_out;
+	}
+
+	ref_clk_rate = clk_get_rate(usb2->ref_clk);
+	if (!ref_clk_rate) {
+		dev_err(dev, "Failed to get ref clock rate\n");
+		err = -EINVAL;
+		goto err_clk_off;
+	}
+
+	usb2ctl = readl(dmu + BCMA_DMU_CRU_USB2_CONTROL);
+
+	if (usb2ctl & BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_PDIV_MASK) {
+		usb_pll_pdiv = usb2ctl;
+		usb_pll_pdiv &= BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_PDIV_MASK;
+		usb_pll_pdiv >>= BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_PDIV_SHIFT;
+	} else {
+		usb_pll_pdiv = 1 << 3;
+	}
+
+	/* Calculate ndiv based on a solid 1920 MHz that is for USB2 PHY */
+	usb_pll_ndiv = (1920000000 * usb_pll_pdiv) / ref_clk_rate;
+
+	/* Unlock DMU PLL settings with some magic value */
+	writel(0x0000ea68, dmu + BCMA_DMU_CRU_CLKSET_KEY);
+
+	/* Write USB 2.0 PLL control setting */
+	usb2ctl &= ~BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_NDIV_MASK;
+	usb2ctl |= usb_pll_ndiv << BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_NDIV_SHIFT;
+	writel(usb2ctl, dmu + BCMA_DMU_CRU_USB2_CONTROL);
+
+	/* Lock DMU PLL settings */
+	writel(0x00000000, dmu + BCMA_DMU_CRU_CLKSET_KEY);
+
+err_clk_off:
+	clk_disable_unprepare(usb2->ref_clk);
+err_out:
+	return err;
+}
+
+static const struct phy_ops ops = {
+	.init		= bcm_ns_usb2_phy_init,
+	.owner		= THIS_MODULE,
+};
+
+static int bcm_ns_usb2_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct bcm_ns_usb2 *usb2;
+	struct resource *res;
+	struct phy_provider *phy_provider;
+
+	usb2 = devm_kzalloc(&pdev->dev, sizeof(*usb2), GFP_KERNEL);
+	if (!usb2)
+		return -ENOMEM;
+	usb2->dev = dev;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dmu");
+	usb2->dmu = devm_ioremap_resource(dev, res);
+	if (IS_ERR(usb2->dmu)) {
+		dev_err(dev, "Failed to map DMU regs\n");
+		return PTR_ERR(usb2->dmu);
+	}
+
+	usb2->ref_clk = devm_clk_get(dev, "phy-ref-clk");
+	if (IS_ERR(usb2->ref_clk)) {
+		dev_err(dev, "Clock not defined\n");
+		return PTR_ERR(usb2->ref_clk);
+	}
+
+	usb2->phy = devm_phy_create(dev, NULL, &ops);
+	if (IS_ERR(dev))
+		return PTR_ERR(dev);
+
+	phy_set_drvdata(usb2->phy, usb2);
+	platform_set_drvdata(pdev, usb2);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id bcm_ns_usb2_id_table[] = {
+	{ .compatible = "brcm,ns-usb2-phy", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, bcm_ns_usb2_id_table);
+
+static struct platform_driver bcm_ns_usb2_driver = {
+	.probe		= bcm_ns_usb2_probe,
+	.driver = {
+		.name = "bcm_ns_usb2",
+		.of_match_table = bcm_ns_usb2_id_table,
+	},
+};
+module_platform_driver(bcm_ns_usb2_driver);
+
+MODULE_LICENSE("GPL v2");

drivers/phy/phy-mt65xx-usb3.c

@@ -134,6 +134,11 @@
 #define U3P_SR_COEF_DIVISOR	1000
 #define U3P_FM_DET_CYCLE_CNT	1024
 
+struct mt65xx_phy_pdata {
+	/* avoid RX sensitivity level degradation only for mt8173 */
+	bool avoid_rx_sen_degradation;
+};
+
 struct mt65xx_phy_instance {
 	struct phy *phy;
 	void __iomem *port_base;
@@ -145,6 +150,7 @@ struct mt65xx_u3phy {
 	struct device *dev;
 	void __iomem *sif_base;	/* include sif2, but exclude port's */
 	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
+	const struct mt65xx_phy_pdata *pdata;
 	struct mt65xx_phy_instance **phys;
 	int nphys;
 };
@@ -241,22 +247,26 @@ static void phy_instance_init(struct mt65xx_u3phy *u3phy,
 		tmp = readl(port_base + U3P_U2PHYACR4);
 		tmp &= ~P2C_U2_GPIO_CTR_MSK;
 		writel(tmp, port_base + U3P_U2PHYACR4);
+	}
 
-		tmp = readl(port_base + U3P_USBPHYACR2);
-		tmp |= PA2_RG_SIF_U2PLL_FORCE_EN;
-		writel(tmp, port_base + U3P_USBPHYACR2);
-
-		tmp = readl(port_base + U3D_U2PHYDCR0);
-		tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
-		writel(tmp, port_base + U3D_U2PHYDCR0);
-	} else {
-		tmp = readl(port_base + U3D_U2PHYDCR0);
-		tmp |= P2C_RG_SIF_U2PLL_FORCE_ON;
-		writel(tmp, port_base + U3D_U2PHYDCR0);
-
-		tmp = readl(port_base + U3P_U2PHYDTM0);
-		tmp |= P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM;
-		writel(tmp, port_base + U3P_U2PHYDTM0);
+	if (u3phy->pdata->avoid_rx_sen_degradation) {
+		if (!index) {
+			tmp = readl(port_base + U3P_USBPHYACR2);
+			tmp |= PA2_RG_SIF_U2PLL_FORCE_EN;
+			writel(tmp, port_base + U3P_USBPHYACR2);
+
+			tmp = readl(port_base + U3D_U2PHYDCR0);
+			tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
+			writel(tmp, port_base + U3D_U2PHYDCR0);
+		} else {
+			tmp = readl(port_base + U3D_U2PHYDCR0);
+			tmp |= P2C_RG_SIF_U2PLL_FORCE_ON;
+			writel(tmp, port_base + U3D_U2PHYDCR0);
+
+			tmp = readl(port_base + U3P_U2PHYDTM0);
+			tmp |= P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM;
+			writel(tmp, port_base + U3P_U2PHYDTM0);
+		}
 	}
 
 	tmp = readl(port_base + U3P_USBPHYACR6);
@@ -318,7 +328,7 @@ static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
 		tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
 		writel(tmp, u3phy->sif_base + U3P_XTALCTL3);
 
-		/* [mt8173]switch 100uA current to SSUSB */
+		/* switch 100uA current to SSUSB */
 		tmp = readl(port_base + U3P_USBPHYACR5);
 		tmp |= PA5_RG_U2_HS_100U_U3_EN;
 		writel(tmp, port_base + U3P_USBPHYACR5);
@@ -335,7 +345,7 @@ static void phy_instance_power_on(struct mt65xx_u3phy *u3phy,
 	tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(4);
 	writel(tmp, port_base + U3P_USBPHYACR5);
 
-	if (index) {
+	if (u3phy->pdata->avoid_rx_sen_degradation && index) {
 		tmp = readl(port_base + U3D_U2PHYDCR0);
 		tmp |= P2C_RG_SIF_U2PLL_FORCE_ON;
 		writel(tmp, port_base + U3D_U2PHYDCR0);
@@ -386,7 +396,9 @@ static void phy_instance_power_off(struct mt65xx_u3phy *u3phy,
 		tmp = readl(port_base + U3P_U3_PHYA_REG0);
 		tmp &= ~P3A_RG_U3_VUSB10_ON;
 		writel(tmp, port_base + U3P_U3_PHYA_REG0);
-	} else {
+	}
+
+	if (u3phy->pdata->avoid_rx_sen_degradation && index) {
 		tmp = readl(port_base + U3D_U2PHYDCR0);
 		tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
 		writel(tmp, port_base + U3D_U2PHYDCR0);
@@ -402,7 +414,7 @@ static void phy_instance_exit(struct mt65xx_u3phy *u3phy,
 	u32 index = instance->index;
 	u32 tmp;
 
-	if (index) {
+	if (u3phy->pdata->avoid_rx_sen_degradation && index) {
 		tmp = readl(port_base + U3D_U2PHYDCR0);
 		tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
 		writel(tmp, port_base + U3D_U2PHYDCR0);
@@ -502,8 +514,24 @@ static struct phy_ops mt65xx_u3phy_ops = {
 	.owner		= THIS_MODULE,
 };
 
+static const struct mt65xx_phy_pdata mt2701_pdata = {
+	.avoid_rx_sen_degradation = false,
+};
+
+static const struct mt65xx_phy_pdata mt8173_pdata = {
+	.avoid_rx_sen_degradation = true,
+};
+
+static const struct of_device_id mt65xx_u3phy_id_table[] = {
+	{ .compatible = "mediatek,mt2701-u3phy", .data = &mt2701_pdata },
+	{ .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mt65xx_u3phy_id_table);
+
 static int mt65xx_u3phy_probe(struct platform_device *pdev)
 {
+	const struct of_device_id *match;
 	struct device *dev = &pdev->dev;
 	struct device_node *np = dev->of_node;
 	struct device_node *child_np;
@@ -513,10 +541,15 @@ static int mt65xx_u3phy_probe(struct platform_device *pdev)
 	struct resource res;
 	int port, retval;
 
+	match = of_match_node(mt65xx_u3phy_id_table, pdev->dev.of_node);
+	if (!match)
+		return -EINVAL;
+
 	u3phy = devm_kzalloc(dev, sizeof(*u3phy), GFP_KERNEL);
 	if (!u3phy)
 		return -ENOMEM;
 
+	u3phy->pdata = match->data;
 	u3phy->nphys = of_get_child_count(np);
 	u3phy->phys = devm_kcalloc(dev, u3phy->nphys,
 				       sizeof(*u3phy->phys), GFP_KERNEL);
@@ -587,12 +620,6 @@ static int mt65xx_u3phy_probe(struct platform_device *pdev)
 	return retval;
 }
 
-static const struct of_device_id mt65xx_u3phy_id_table[] = {
-	{ .compatible = "mediatek,mt8173-u3phy", },
-	{ },
-};
-MODULE_DEVICE_TABLE(of, mt65xx_u3phy_id_table);
-
 static struct platform_driver mt65xx_u3phy_driver = {
 	.probe		= mt65xx_u3phy_probe,
 	.driver		= {

drivers/phy/phy-rcar-gen2.c

@@ -195,6 +195,7 @@ static const struct of_device_id rcar_gen2_phy_match_table[] = {
 	{ .compatible = "renesas,usb-phy-r8a7790" },
 	{ .compatible = "renesas,usb-phy-r8a7791" },
 	{ .compatible = "renesas,usb-phy-r8a7794" },
+	{ .compatible = "renesas,rcar-gen2-usb-phy" },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, rcar_gen2_phy_match_table);

drivers/phy/phy-rcar-gen3-usb2.c

@@ -12,6 +12,7 @@
  * published by the Free Software Foundation.
  */
 
+#include <linux/extcon.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/module.h>
@@ -19,6 +20,7 @@
 #include <linux/of_address.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
 
 /******* USB2.0 Host registers (original offset is +0x200) *******/
 #define USB2_INT_ENABLE		0x000
@@ -74,20 +76,17 @@
 #define USB2_ADPCTRL_IDPULLUP		BIT(5)	/* 1 = ID sampling is enabled */
 #define USB2_ADPCTRL_DRVVBUS		BIT(4)
 
-struct rcar_gen3_data {
-	void __iomem *base;
-	struct clk *clk;
-};
-
 struct rcar_gen3_chan {
-	struct rcar_gen3_data usb2;
+	void __iomem *base;
+	struct extcon_dev *extcon;
 	struct phy *phy;
+	struct regulator *vbus;
 	bool has_otg;
 };
 
 static void rcar_gen3_set_host_mode(struct rcar_gen3_chan *ch, int host)
 {
-	void __iomem *usb2_base = ch->usb2.base;
+	void __iomem *usb2_base = ch->base;
 	u32 val = readl(usb2_base + USB2_COMMCTRL);
 
 	dev_vdbg(&ch->phy->dev, "%s: %08x, %d\n", __func__, val, host);
@@ -100,7 +99,7 @@ static void rcar_gen3_set_host_mode(struct rcar_gen3_chan *ch, int host)
 
 static void rcar_gen3_set_linectrl(struct rcar_gen3_chan *ch, int dp, int dm)
 {
-	void __iomem *usb2_base = ch->usb2.base;
+	void __iomem *usb2_base = ch->base;
 	u32 val = readl(usb2_base + USB2_LINECTRL1);
 
 	dev_vdbg(&ch->phy->dev, "%s: %08x, %d, %d\n", __func__, val, dp, dm);
@@ -114,7 +113,7 @@ static void rcar_gen3_set_linectrl(struct rcar_gen3_chan *ch, int dp, int dm)
 
 static void rcar_gen3_enable_vbus_ctrl(struct rcar_gen3_chan *ch, int vbus)
 {
-	void __iomem *usb2_base = ch->usb2.base;
+	void __iomem *usb2_base = ch->base;
 	u32 val = readl(usb2_base + USB2_ADPCTRL);
 
 	dev_vdbg(&ch->phy->dev, "%s: %08x, %d\n", __func__, val, vbus);
@@ -130,6 +129,9 @@ static void rcar_gen3_init_for_host(struct rcar_gen3_chan *ch)
 	rcar_gen3_set_linectrl(ch, 1, 1);
 	rcar_gen3_set_host_mode(ch, 1);
 	rcar_gen3_enable_vbus_ctrl(ch, 1);
+
+	extcon_set_cable_state_(ch->extcon, EXTCON_USB_HOST, true);
+	extcon_set_cable_state_(ch->extcon, EXTCON_USB, false);
 }
 
 static void rcar_gen3_init_for_peri(struct rcar_gen3_chan *ch)
@@ -137,17 +139,20 @@ static void rcar_gen3_init_for_peri(struct rcar_gen3_chan *ch)
 	rcar_gen3_set_linectrl(ch, 0, 1);
 	rcar_gen3_set_host_mode(ch, 0);
 	rcar_gen3_enable_vbus_ctrl(ch, 0);
+
+	extcon_set_cable_state_(ch->extcon, EXTCON_USB_HOST, false);
+	extcon_set_cable_state_(ch->extcon, EXTCON_USB, true);
 }
 
 static bool rcar_gen3_check_vbus(struct rcar_gen3_chan *ch)
 {
-	return !!(readl(ch->usb2.base + USB2_ADPCTRL) &
+	return !!(readl(ch->base + USB2_ADPCTRL) &
 		  USB2_ADPCTRL_OTGSESSVLD);
 }
 
 static bool rcar_gen3_check_id(struct rcar_gen3_chan *ch)
 {
-	return !!(readl(ch->usb2.base + USB2_ADPCTRL) & USB2_ADPCTRL_IDDIG);
+	return !!(readl(ch->base + USB2_ADPCTRL) & USB2_ADPCTRL_IDDIG);
 }
 
 static void rcar_gen3_device_recognition(struct rcar_gen3_chan *ch)
@@ -166,7 +171,7 @@ static void rcar_gen3_device_recognition(struct rcar_gen3_chan *ch)
 
 static void rcar_gen3_init_otg(struct rcar_gen3_chan *ch)
 {
-	void __iomem *usb2_base = ch->usb2.base;
+	void __iomem *usb2_base = ch->base;
 	u32 val;
 
 	val = readl(usb2_base + USB2_VBCTRL);
@@ -187,7 +192,7 @@ static void rcar_gen3_init_otg(struct rcar_gen3_chan *ch)
 static int rcar_gen3_phy_usb2_init(struct phy *p)
 {
 	struct rcar_gen3_chan *channel = phy_get_drvdata(p);
-	void __iomem *usb2_base = channel->usb2.base;
+	void __iomem *usb2_base = channel->base;
 
 	/* Initialize USB2 part */
 	writel(USB2_INT_ENABLE_INIT, usb2_base + USB2_INT_ENABLE);
@@ -205,7 +210,7 @@ static int rcar_gen3_phy_usb2_exit(struct phy *p)
 {
 	struct rcar_gen3_chan *channel = phy_get_drvdata(p);
 
-	writel(0, channel->usb2.base + USB2_INT_ENABLE);
+	writel(0, channel->base + USB2_INT_ENABLE);
 
 	return 0;
 }
@@ -213,8 +218,15 @@ static int rcar_gen3_phy_usb2_exit(struct phy *p)
 static int rcar_gen3_phy_usb2_power_on(struct phy *p)
 {
 	struct rcar_gen3_chan *channel = phy_get_drvdata(p);
-	void __iomem *usb2_base = channel->usb2.base;
+	void __iomem *usb2_base = channel->base;
 	u32 val;
+	int ret;
+
+	if (channel->vbus) {
+		ret = regulator_enable(channel->vbus);
+		if (ret)
+			return ret;
+	}
 
 	val = readl(usb2_base + USB2_USBCTR);
 	val |= USB2_USBCTR_PLL_RST;
@@ -225,17 +237,29 @@ static int rcar_gen3_phy_usb2_power_on(struct phy *p)
 	return 0;
 }
 
+static int rcar_gen3_phy_usb2_power_off(struct phy *p)
+{
+	struct rcar_gen3_chan *channel = phy_get_drvdata(p);
+	int ret = 0;
+
+	if (channel->vbus)
+		ret = regulator_disable(channel->vbus);
+
+	return ret;
+}
+
 static struct phy_ops rcar_gen3_phy_usb2_ops = {
 	.init		= rcar_gen3_phy_usb2_init,
 	.exit		= rcar_gen3_phy_usb2_exit,
 	.power_on	= rcar_gen3_phy_usb2_power_on,
+	.power_off	= rcar_gen3_phy_usb2_power_off,
 	.owner		= THIS_MODULE,
 };
 
 static irqreturn_t rcar_gen3_phy_usb2_irq(int irq, void *_ch)
 {
 	struct rcar_gen3_chan *ch = _ch;
-	void __iomem *usb2_base = ch->usb2.base;
+	void __iomem *usb2_base = ch->base;
 	u32 status = readl(usb2_base + USB2_OBINTSTA);
 	irqreturn_t ret = IRQ_NONE;
 
@@ -251,10 +275,17 @@ static irqreturn_t rcar_gen3_phy_usb2_irq(int irq, void *_ch)
 
 static const struct of_device_id rcar_gen3_phy_usb2_match_table[] = {
 	{ .compatible = "renesas,usb2-phy-r8a7795" },
+	{ .compatible = "renesas,rcar-gen3-usb2-phy" },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, rcar_gen3_phy_usb2_match_table);
 
+static const unsigned int rcar_gen3_phy_cable[] = {
+	EXTCON_USB,
+	EXTCON_USB_HOST,
+	EXTCON_NONE,
+};
+
 static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -273,18 +304,30 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	channel->usb2.base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(channel->usb2.base))
-		return PTR_ERR(channel->usb2.base);
+	channel->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(channel->base))
+		return PTR_ERR(channel->base);
 
 	/* call request_irq for OTG */
 	irq = platform_get_irq(pdev, 0);
 	if (irq >= 0) {
+		int ret;
+
 		irq = devm_request_irq(dev, irq, rcar_gen3_phy_usb2_irq,
 				       IRQF_SHARED, dev_name(dev), channel);
 		if (irq < 0)
 			dev_err(dev, "No irq handler (%d)\n", irq);
 		channel->has_otg = true;
+		channel->extcon = devm_extcon_dev_allocate(dev,
+							rcar_gen3_phy_cable);
+		if (IS_ERR(channel->extcon))
+			return PTR_ERR(channel->extcon);
+
+		ret = devm_extcon_dev_register(dev, channel->extcon);
+		if (ret < 0) {
+			dev_err(dev, "Failed to register extcon\n");
+			return ret;
+		}
 	}
 
 	/* devm_phy_create() will call pm_runtime_enable(dev); */
@@ -294,6 +337,13 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev)
 		return PTR_ERR(channel->phy);
 	}
 
+	channel->vbus = devm_regulator_get_optional(dev, "vbus");
+	if (IS_ERR(channel->vbus)) {
+		if (PTR_ERR(channel->vbus) == -EPROBE_DEFER)
+			return PTR_ERR(channel->vbus);
+		channel->vbus = NULL;
+	}
+
 	phy_set_drvdata(channel->phy, channel);
 
 	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);

drivers/phy/phy-rockchip-usb.c

@@ -216,7 +216,7 @@ static int rockchip_usb_phy_init(struct rockchip_usb_phy_base *base,
 			init.parent_names = &clk_name;
 			init.num_parents = 1;
 		} else {
-			init.flags = CLK_IS_ROOT;
+			init.flags = 0;
 			init.parent_names = NULL;
 			init.num_parents = 0;
 		}

include/linux/bcma/bcma.h

@@ -4,6 +4,7 @@
 #include <linux/pci.h>
 #include <linux/mod_devicetable.h>
 
+#include <linux/bcma/bcma_driver_arm_c9.h>
 #include <linux/bcma/bcma_driver_chipcommon.h>
 #include <linux/bcma/bcma_driver_pci.h>
 #include <linux/bcma/bcma_driver_pcie2.h>

include/linux/bcma/bcma_driver_arm_c9.h

+#ifndef LINUX_BCMA_DRIVER_ARM_C9_H_
+#define LINUX_BCMA_DRIVER_ARM_C9_H_
+
+/* DMU (Device Management Unit) */
+#define BCMA_DMU_CRU_USB2_CONTROL			0x0164
+#define  BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_NDIV_MASK	0x00000FFC
+#define  BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_NDIV_SHIFT	2
+#define  BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_PDIV_MASK	0x00007000
+#define  BCMA_DMU_CRU_USB2_CONTROL_USB_PLL_PDIV_SHIFT	12
+#define BCMA_DMU_CRU_CLKSET_KEY				0x0180
+#define BCMA_DMU_CRU_STRAPS_CTRL			0x02A0
+#define  BCMA_DMU_CRU_STRAPS_CTRL_USB3			0x00000010
+#define  BCMA_DMU_CRU_STRAPS_CTRL_4BYTE			0x00008000
+
+#endif /* LINUX_BCMA_DRIVER_ARM_C9_H_ */

include/linux/mfd/syscon/exynos5-pmu.h

@@ -38,6 +38,9 @@
 
 /* Exynos5433 specific register definitions */
 #define EXYNOS5433_USBHOST30_PHY_CONTROL	(0x728)
+#define EXYNOS5433_MIPI_PHY0_CONTROL		(0x710)
+#define EXYNOS5433_MIPI_PHY1_CONTROL		(0x714)
+#define EXYNOS5433_MIPI_PHY2_CONTROL		(0x718)
 
 #define EXYNOS5_PHY_ENABLE			BIT(0)