Commit ebd10e07 authored by Virupax Sadashivpetimath's avatar Virupax Sadashivpetimath Committed by Ben Dooks

i2c-nomadik: add code to retry on timeout failure

It is seen that i2c-nomadik controller randomly stops generating the
interrupts leading to a i2c timeout. As a workaround to this problem,
add retries to the on going transfer on failure.
Signed-off-by: default avatarVirupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: default avatarJonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: default avatarBen Dooks <ben-linux@fluff.org>
parent b0e751a9
......@@ -255,8 +255,6 @@ static int init_hw(struct nmk_i2c_dev *dev)
{
int stat;
clk_enable(dev->clk);
stat = flush_i2c_fifo(dev);
if (stat)
goto exit;
......@@ -271,8 +269,6 @@ static int init_hw(struct nmk_i2c_dev *dev)
dev->cli.operation = I2C_NO_OPERATION;
exit:
/* TODO: Why disable clocks after init hw? */
clk_disable(dev->clk);
/*
* TODO: What is this delay for?
* Must be pretty pointless since the hw block
......@@ -572,6 +568,7 @@ static int nmk_i2c_xfer(struct i2c_adapter *i2c_adap,
u32 cause;
struct nmk_i2c_dev *dev = i2c_get_adapdata(i2c_adap);
u32 i2c_sr;
int j;
dev->busy = true;
......@@ -579,63 +576,67 @@ static int nmk_i2c_xfer(struct i2c_adapter *i2c_adap,
regulator_enable(dev->regulator);
pm_runtime_get_sync(&dev->pdev->dev);
clk_enable(dev->clk);
status = init_hw(dev);
if (status)
goto out2;
goto out;
clk_enable(dev->clk);
/* setup the i2c controller */
setup_i2c_controller(dev);
for (j = 0; j < 3; j++) {
/* setup the i2c controller */
setup_i2c_controller(dev);
for (i = 0; i < num_msgs; i++) {
if (unlikely(msgs[i].flags & I2C_M_TEN)) {
dev_err(&dev->pdev->dev, "10 bit addressing"
"not supported\n");
for (i = 0; i < num_msgs; i++) {
if (unlikely(msgs[i].flags & I2C_M_TEN)) {
dev_err(&dev->pdev->dev, "10 bit addressing"
"not supported\n");
status = -EINVAL;
goto out;
}
dev->cli.slave_adr = msgs[i].addr;
dev->cli.buffer = msgs[i].buf;
dev->cli.count = msgs[i].len;
dev->stop = (i < (num_msgs - 1)) ? 0 : 1;
dev->result = 0;
if (msgs[i].flags & I2C_M_RD) {
/* it is a read operation */
dev->cli.operation = I2C_READ;
status = read_i2c(dev);
} else {
/* write operation */
dev->cli.operation = I2C_WRITE;
status = write_i2c(dev);
}
if (status || (dev->result)) {
i2c_sr = readl(dev->virtbase + I2C_SR);
/*
* Check if the controller I2C operation status is set
* to ABORT(11b).
*/
if (((i2c_sr >> 2) & 0x3) == 0x3) {
/* get the abort cause */
cause = (i2c_sr >> 4)
& 0x7;
dev_err(&dev->pdev->dev, "%s\n", cause >=
ARRAY_SIZE(abort_causes) ?
status = -EINVAL;
goto out;
}
dev->cli.slave_adr = msgs[i].addr;
dev->cli.buffer = msgs[i].buf;
dev->cli.count = msgs[i].len;
dev->stop = (i < (num_msgs - 1)) ? 0 : 1;
dev->result = 0;
if (msgs[i].flags & I2C_M_RD) {
/* it is a read operation */
dev->cli.operation = I2C_READ;
status = read_i2c(dev);
} else {
/* write operation */
dev->cli.operation = I2C_WRITE;
status = write_i2c(dev);
}
if (status || (dev->result)) {
i2c_sr = readl(dev->virtbase + I2C_SR);
/*
* Check if the controller I2C operation status
* is set to ABORT(11b).
*/
if (((i2c_sr >> 2) & 0x3) == 0x3) {
/* get the abort cause */
cause = (i2c_sr >> 4)
& 0x7;
dev_err(&dev->pdev->dev, "%s\n", cause
>= ARRAY_SIZE(abort_causes) ?
"unknown reason" :
abort_causes[cause]);
}
}
status = status ? status : dev->result;
goto out;
status = status ? status : dev->result;
break;
}
udelay(I2C_DELAY);
}
udelay(I2C_DELAY);
if (status == 0)
break;
}
out:
clk_disable(dev->clk);
out2:
pm_runtime_put_sync(&dev->pdev->dev);
if (dev->regulator)
regulator_disable(dev->regulator);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment