dt-bindings: qcom_nandc: IPQ4019 QPIC NAND documentation

1. Qualcom IPQ4019 SoC uses QPIC NAND controller version 1.4.0
   which uses BAM DMA Engine while IPQ806x uses EBI2 NAND
   which uses ADM DMA Engine.
2. QPIC NAND will 3 BAM channels: command, data tx and data rx
   while EBI2 NAND uses only single ADM channel.
3. CRCI is only required for ADM DMA and its not required for
   BAM DMA.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Documentation/devicetree/bindings/mtd/qcom_nandc.txt

 * Qualcomm NAND controller
 
 Required properties:
-- compatible:		should be "qcom,ipq806x-nand"
+- compatible:		must be one of the following:
+    * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x
+			    SoC and it uses ADM DMA
+    * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in
+                            IPQ4019 SoC and it uses BAM DMA
+
 - reg:			MMIO address range
 - clocks:		must contain core clock and always on clock
 - clock-names:		must contain "core" for the core clock and "aon" for the
 			always on clock
+
+EBI2 specific properties:
 - dmas:			DMA specifier, consisting of a phandle to the ADM DMA
 			controller node and the channel number to be used for
 			NAND. Refer to dma.txt and qcom_adm.txt for more details
@@ -16,6 +23,12 @@ Required properties:
 - qcom,data-crci:	must contain the ADM data type CRCI block instance
 			number specified for the NAND controller on the given
 			platform
+
+QPIC specific properties:
+- dmas:			DMA specifier, consisting of a phandle to the BAM DMA
+			and the channel number to be used for NAND. Refer to
+			dma.txt, qcom_bam_dma.txt for more details
+- dma-names:		must contain all 3 channel names : "tx", "rx", "cmd"
 - #address-cells:	<1> - subnodes give the chip-select number
 - #size-cells:		<0>
 
@@ -82,3 +95,43 @@ nand-controller@1ac00000 {
 		};
 	};
 };
+
+nand-controller@79b0000 {
+	compatible = "qcom,ipq4019-nand";
+	reg = <0x79b0000 0x1000>;
+
+	clocks = <&gcc GCC_QPIC_CLK>,
+		<&gcc GCC_QPIC_AHB_CLK>;
+	clock-names = "core", "aon";
+
+	dmas = <&qpicbam 0>,
+		<&qpicbam 1>,
+		<&qpicbam 2>;
+	dma-names = "tx", "rx", "cmd";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	nand@0 {
+		reg = <0>;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "boot-nand";
+				reg = <0 0x58a0000>;
+			};
+
+			partition@58a0000 {
+				label = "fs-nand";
+				reg = <0x58a0000 0x4000000>;
+			};
+		};
+	};
+};