Commit ee302767 authored by Daniel Drake's avatar Daniel Drake Committed by Jeff Garzik

[PATCH] zd1211rw: Consistency for address space constants

The zd1211rw address space has confused me once too many times. This
patch introduces the following naming notation:

Memory space is split into segments (cr, fw, eeprom) and segments may
contain components (e.g. boot code inside eeprom). These names are
arbitrary and only for the description below:

x_START: Absolute address of segment start
(previously these were named such as CR_BASE_OFFSET, but they weren't
really offsets unless you were considering them as an offset to 0)

x_LEN: Segment length

x_y_LEN: Length of component y of segment x

x_y_OFFSET: Relative address of component y into segment x. The absolute
address for this component is (x_START + x_y_OFFSET)

I also renamed EEPROM registers to EEPROM data. These 'registers' can't
be written to using standard I/O and really represent predefined data
from the vendor.
Signed-off-by: default avatarDaniel Drake <dsd@gentoo.org>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
parent a2bdcc67
......@@ -594,49 +594,49 @@
/*
* Upper 16 bit contains the regulatory domain.
*/
#define E2P_SUBID E2P_REG(0x00)
#define E2P_POD E2P_REG(0x02)
#define E2P_MAC_ADDR_P1 E2P_REG(0x04)
#define E2P_MAC_ADDR_P2 E2P_REG(0x06)
#define E2P_PWR_CAL_VALUE1 E2P_REG(0x08)
#define E2P_PWR_CAL_VALUE2 E2P_REG(0x0a)
#define E2P_PWR_CAL_VALUE3 E2P_REG(0x0c)
#define E2P_PWR_CAL_VALUE4 E2P_REG(0x0e)
#define E2P_PWR_INT_VALUE1 E2P_REG(0x10)
#define E2P_PWR_INT_VALUE2 E2P_REG(0x12)
#define E2P_PWR_INT_VALUE3 E2P_REG(0x14)
#define E2P_PWR_INT_VALUE4 E2P_REG(0x16)
#define E2P_SUBID E2P_DATA(0x00)
#define E2P_POD E2P_DATA(0x02)
#define E2P_MAC_ADDR_P1 E2P_DATA(0x04)
#define E2P_MAC_ADDR_P2 E2P_DATA(0x06)
#define E2P_PWR_CAL_VALUE1 E2P_DATA(0x08)
#define E2P_PWR_CAL_VALUE2 E2P_DATA(0x0a)
#define E2P_PWR_CAL_VALUE3 E2P_DATA(0x0c)
#define E2P_PWR_CAL_VALUE4 E2P_DATA(0x0e)
#define E2P_PWR_INT_VALUE1 E2P_DATA(0x10)
#define E2P_PWR_INT_VALUE2 E2P_DATA(0x12)
#define E2P_PWR_INT_VALUE3 E2P_DATA(0x14)
#define E2P_PWR_INT_VALUE4 E2P_DATA(0x16)
/* Contains a bit for each allowed channel. It gives for Europe (ETSI 0x30)
* also only 11 channels. */
#define E2P_ALLOWED_CHANNEL E2P_REG(0x18)
#define E2P_PHY_REG E2P_REG(0x1a)
#define E2P_DEVICE_VER E2P_REG(0x20)
#define E2P_36M_CAL_VALUE1 E2P_REG(0x28)
#define E2P_36M_CAL_VALUE2 E2P_REG(0x2a)
#define E2P_36M_CAL_VALUE3 E2P_REG(0x2c)
#define E2P_36M_CAL_VALUE4 E2P_REG(0x2e)
#define E2P_11A_INT_VALUE1 E2P_REG(0x30)
#define E2P_11A_INT_VALUE2 E2P_REG(0x32)
#define E2P_11A_INT_VALUE3 E2P_REG(0x34)
#define E2P_11A_INT_VALUE4 E2P_REG(0x36)
#define E2P_48M_CAL_VALUE1 E2P_REG(0x38)
#define E2P_48M_CAL_VALUE2 E2P_REG(0x3a)
#define E2P_48M_CAL_VALUE3 E2P_REG(0x3c)
#define E2P_48M_CAL_VALUE4 E2P_REG(0x3e)
#define E2P_48M_INT_VALUE1 E2P_REG(0x40)
#define E2P_48M_INT_VALUE2 E2P_REG(0x42)
#define E2P_48M_INT_VALUE3 E2P_REG(0x44)
#define E2P_48M_INT_VALUE4 E2P_REG(0x46)
#define E2P_54M_CAL_VALUE1 E2P_REG(0x48) /* ??? */
#define E2P_54M_CAL_VALUE2 E2P_REG(0x4a)
#define E2P_54M_CAL_VALUE3 E2P_REG(0x4c)
#define E2P_54M_CAL_VALUE4 E2P_REG(0x4e)
#define E2P_54M_INT_VALUE1 E2P_REG(0x50)
#define E2P_54M_INT_VALUE2 E2P_REG(0x52)
#define E2P_54M_INT_VALUE3 E2P_REG(0x54)
#define E2P_54M_INT_VALUE4 E2P_REG(0x56)
#define E2P_ALLOWED_CHANNEL E2P_DATA(0x18)
#define E2P_PHY_REG E2P_DATA(0x1a)
#define E2P_DEVICE_VER E2P_DATA(0x20)
#define E2P_36M_CAL_VALUE1 E2P_DATA(0x28)
#define E2P_36M_CAL_VALUE2 E2P_DATA(0x2a)
#define E2P_36M_CAL_VALUE3 E2P_DATA(0x2c)
#define E2P_36M_CAL_VALUE4 E2P_DATA(0x2e)
#define E2P_11A_INT_VALUE1 E2P_DATA(0x30)
#define E2P_11A_INT_VALUE2 E2P_DATA(0x32)
#define E2P_11A_INT_VALUE3 E2P_DATA(0x34)
#define E2P_11A_INT_VALUE4 E2P_DATA(0x36)
#define E2P_48M_CAL_VALUE1 E2P_DATA(0x38)
#define E2P_48M_CAL_VALUE2 E2P_DATA(0x3a)
#define E2P_48M_CAL_VALUE3 E2P_DATA(0x3c)
#define E2P_48M_CAL_VALUE4 E2P_DATA(0x3e)
#define E2P_48M_INT_VALUE1 E2P_DATA(0x40)
#define E2P_48M_INT_VALUE2 E2P_DATA(0x42)
#define E2P_48M_INT_VALUE3 E2P_DATA(0x44)
#define E2P_48M_INT_VALUE4 E2P_DATA(0x46)
#define E2P_54M_CAL_VALUE1 E2P_DATA(0x48) /* ??? */
#define E2P_54M_CAL_VALUE2 E2P_DATA(0x4a)
#define E2P_54M_CAL_VALUE3 E2P_DATA(0x4c)
#define E2P_54M_CAL_VALUE4 E2P_DATA(0x4e)
#define E2P_54M_INT_VALUE1 E2P_DATA(0x50)
#define E2P_54M_INT_VALUE2 E2P_DATA(0x52)
#define E2P_54M_INT_VALUE3 E2P_DATA(0x54)
#define E2P_54M_INT_VALUE4 E2P_DATA(0x56)
/* All 16 bit values */
#define FW_FIRMWARE_VER FW_REG(0)
......@@ -653,20 +653,33 @@
/* 0x2 - link led on? */
enum {
CR_BASE_OFFSET = 0x9000,
FW_START_OFFSET = 0xee00,
FW_BASE_ADDR_OFFSET = FW_START_OFFSET + 0x1d,
EEPROM_START_OFFSET = 0xf800,
EEPROM_SIZE = 0x800, /* words */
LOAD_CODE_SIZE = 0xe, /* words */
LOAD_VECT_SIZE = 0x10000 - 0xfff7, /* words */
EEPROM_REGS_OFFSET = LOAD_CODE_SIZE + LOAD_VECT_SIZE,
EEPROM_REGS_SIZE = 0x7e, /* words */
E2P_BASE_OFFSET = EEPROM_START_OFFSET +
EEPROM_REGS_OFFSET,
};
/* CONTROL REGISTERS */
CR_START = 0x9000,
/* FIRMWARE */
FW_START = 0xee00,
/* The word at this offset contains the base address of the FW_REG
* registers */
FW_REGS_ADDR_OFFSET = 0x1d,
#define FW_REG_TABLE_ADDR USB_ADDR(FW_START_OFFSET + 0x1d)
/* EEPROM */
E2P_START = 0xf800,
E2P_LEN = 0x800,
/* EEPROM layout */
E2P_LOAD_CODE_LEN = 0xe, /* base 0xf800 */
E2P_LOAD_VECT_LEN = 0x9, /* base 0xf80e */
/* E2P_DATA indexes into this */
E2P_DATA_LEN = 0x7e, /* base 0xf817 */
E2P_BOOT_CODE_LEN = 0x760, /* base 0xf895 */
E2P_INTR_VECT_LEN = 0xb, /* base 0xfff5 */
/* Some precomputed offsets into the EEPROM */
E2P_DATA_OFFSET = E2P_LOAD_CODE_LEN + E2P_LOAD_VECT_LEN,
E2P_BOOT_CODE_OFFSET = E2P_DATA_OFFSET + E2P_DATA_LEN,
};
enum {
/* indices for ofdm_cal_values */
......
......@@ -55,7 +55,7 @@ enum {
#define ZD_NULL_ADDR ((zd_addr_t)0)
#define USB_REG(offset) ZD_ADDR(USB_BASE, offset) /* word addressing */
#define CTL_REG(offset) ZD_ADDR(CR_BASE, offset) /* byte addressing */
#define E2P_REG(offset) ZD_ADDR(E2P_BASE, offset) /* word addressing */
#define E2P_DATA(offset) ZD_ADDR(E2P_BASE, offset) /* word addressing */
#define FW_REG(offset) ZD_ADDR(FW_BASE, offset) /* word addressing */
static inline zd_addr_t zd_inc_word(zd_addr_t addr)
......
......@@ -152,10 +152,10 @@ static u16 usb_addr(struct zd_usb *usb, zd_addr_t addr)
switch (base) {
case CR_BASE:
offset += CR_BASE_OFFSET;
offset += CR_START;
break;
case E2P_BASE:
offset += E2P_BASE_OFFSET;
offset += E2P_START + E2P_DATA_OFFSET;
break;
case FW_BASE:
offset += usb->fw_base_offset;
......@@ -297,14 +297,13 @@ static int handle_version_mismatch(struct usb_device *udev, u8 device_type,
if (r)
goto error;
r = upload_code(udev, ur_fw->data, ur_fw->size, FW_START_OFFSET,
REBOOT);
r = upload_code(udev, ur_fw->data, ur_fw->size, FW_START, REBOOT);
if (r)
goto error;
offset = ((EEPROM_REGS_OFFSET + EEPROM_REGS_SIZE) * sizeof(u16));
offset = (E2P_BOOT_CODE_OFFSET * sizeof(u16));
r = upload_code(udev, ub_fw->data + offset, ub_fw->size - offset,
E2P_BASE_OFFSET + EEPROM_REGS_SIZE, REBOOT);
E2P_START + E2P_BOOT_CODE_OFFSET, REBOOT);
/* At this point, the vendor driver downloads the whole firmware
* image, hacks around with version IDs, and uploads it again,
......@@ -333,7 +332,7 @@ static int upload_firmware(struct usb_device *udev, u8 device_type)
if (r)
goto error;
fw_bcdDevice = get_word(ub_fw->data, EEPROM_REGS_OFFSET);
fw_bcdDevice = get_word(ub_fw->data, E2P_DATA_OFFSET);
if (fw_bcdDevice != bcdDevice) {
dev_info(&udev->dev,
......@@ -359,8 +358,7 @@ static int upload_firmware(struct usb_device *udev, u8 device_type)
if (r)
goto error;
r = upload_code(udev, uph_fw->data, uph_fw->size, FW_START_OFFSET,
REBOOT);
r = upload_code(udev, uph_fw->data, uph_fw->size, FW_START, REBOOT);
if (r) {
dev_err(&udev->dev,
"Could not upload firmware code uph. Error number %d\n",
......@@ -899,7 +897,7 @@ int zd_usb_init_hw(struct zd_usb *usb)
ZD_ASSERT(mutex_is_locked(&chip->mutex));
r = zd_ioread16_locked(chip, &usb->fw_base_offset,
USB_REG((u16)FW_BASE_ADDR_OFFSET));
USB_REG(FW_START + FW_REGS_ADDR_OFFSET));
if (r)
return r;
dev_dbg_f(zd_usb_dev(usb), "fw_base_offset: %#06hx\n",
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment