drivers: PL011: refactor pl011_set_termios()

Split the pl011_set_termios() function into smaller chunks to allow
easier reuse later when adding SBSA support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/amba-pl011.c

@@ -1705,6 +1705,38 @@ static void pl011_shutdown(struct uart_port *port)
 		uap->port.ops->flush_buffer(port);
 }
 
+static void
+pl011_setup_status_masks(struct uart_port *port, struct ktermios *termios)
+{
+	port->read_status_mask = UART011_DR_OE | 255;
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |= UART011_DR_FE | UART011_DR_PE;
+	if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
+		port->read_status_mask |= UART011_DR_BE;
+
+	/*
+	 * Characters to ignore
+	 */
+	port->ignore_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		port->ignore_status_mask |= UART011_DR_FE | UART011_DR_PE;
+	if (termios->c_iflag & IGNBRK) {
+		port->ignore_status_mask |= UART011_DR_BE;
+		/*
+		 * If we're ignoring parity and break indicators,
+		 * ignore overruns too (for real raw support).
+		 */
+		if (termios->c_iflag & IGNPAR)
+			port->ignore_status_mask |= UART011_DR_OE;
+	}
+
+	/*
+	 * Ignore all characters if CREAD is not set.
+	 */
+	if ((termios->c_cflag & CREAD) == 0)
+		port->ignore_status_mask |= UART_DUMMY_DR_RX;
+}
+
 static void
 pl011_set_termios(struct uart_port *port, struct ktermios *termios,
 		     struct ktermios *old)
@@ -1769,33 +1801,7 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios,
 	 */
 	uart_update_timeout(port, termios->c_cflag, baud);
 
-	port->read_status_mask = UART011_DR_OE | 255;
-	if (termios->c_iflag & INPCK)
-		port->read_status_mask |= UART011_DR_FE | UART011_DR_PE;
-	if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
-		port->read_status_mask |= UART011_DR_BE;
-
-	/*
-	 * Characters to ignore
-	 */
-	port->ignore_status_mask = 0;
-	if (termios->c_iflag & IGNPAR)
-		port->ignore_status_mask |= UART011_DR_FE | UART011_DR_PE;
-	if (termios->c_iflag & IGNBRK) {
-		port->ignore_status_mask |= UART011_DR_BE;
-		/*
-		 * If we're ignoring parity and break indicators,
-		 * ignore overruns too (for real raw support).
-		 */
-		if (termios->c_iflag & IGNPAR)
-			port->ignore_status_mask |= UART011_DR_OE;
-	}
-
-	/*
-	 * Ignore all characters if CREAD is not set.
-	 */
-	if ((termios->c_cflag & CREAD) == 0)
-		port->ignore_status_mask |= UART_DUMMY_DR_RX;
+	pl011_setup_status_masks(port, termios);
 
 	if (UART_ENABLE_MS(port, termios->c_cflag))
 		pl011_enable_ms(port);