Commit effd4d9a authored by Johannes Berg's avatar Johannes Berg Committed by John W. Linville

iwlagn: do not use interruptible waits

Since the dawn of its time, iwlwifi has used
interruptible waits to wait for synchronous
commands and firmware loading.

This leads to "interesting" bugs, because it
can't actually handle the interruptions; for
example when a command sending is interrupted
it will assume the command completed fully,
and then leave it pending, which leads to all
kinds of trouble when the command finishes
later.

Since there's no easy way to gracefully deal
with interruptions, fix the driver to not use
interruptible waits.

This at least fixes the error
iwlagn 0000:02:00.0: Error: Response NULL in  'REPLY_SCAN_ABORT_CMD'

I have seen in P2P testing, but it is likely
that there are other errors caused by this.

Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable@kernel.org [2.6.24+]
Signed-off-by: default avatarJohannes Berg <johannes.berg@intel.com>
Signed-off-by: default avatarWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
parent 7d8f2d50
......@@ -114,13 +114,8 @@ static int iwlagn_load_section(struct iwl_priv *priv, const char *name,
FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_ENDTFD);
IWL_DEBUG_FW(priv, "%s uCode section being loaded...\n", name);
ret = wait_event_interruptible_timeout(priv->shrd->wait_command_queue,
priv->ucode_write_complete, 5 * HZ);
if (ret == -ERESTARTSYS) {
IWL_ERR(priv, "Could not load the %s uCode section due "
"to interrupt\n", name);
return ret;
}
ret = wait_event_timeout(priv->shrd->wait_command_queue,
priv->ucode_write_complete, 5 * HZ);
if (!ret) {
IWL_ERR(priv, "Could not load the %s uCode section\n",
name);
......
......@@ -869,7 +869,7 @@ void iwlagn_fw_error(struct iwl_priv *priv, bool ondemand)
* commands by clearing the ready bit */
clear_bit(STATUS_READY, &priv->shrd->status);
wake_up_interruptible(&priv->shrd->wait_command_queue);
wake_up(&priv->shrd->wait_command_queue);
if (!ondemand) {
/*
......
......@@ -644,7 +644,7 @@ static void iwl_rx_card_state_notif(struct iwl_priv *priv,
wiphy_rfkill_set_hw_state(priv->hw->wiphy,
test_bit(STATUS_RF_KILL_HW, &priv->shrd->status));
else
wake_up_interruptible(&priv->shrd->wait_command_queue);
wake_up(&priv->shrd->wait_command_queue);
}
static void iwl_rx_missed_beacon_notif(struct iwl_priv *priv,
......
......@@ -657,7 +657,7 @@ static void iwl_irq_handle_error(struct iwl_trans *trans)
*/
clear_bit(STATUS_READY, &trans->shrd->status);
clear_bit(STATUS_HCMD_ACTIVE, &trans->shrd->status);
wake_up_interruptible(&priv->shrd->wait_command_queue);
wake_up(&priv->shrd->wait_command_queue);
IWL_ERR(trans, "RF is used by WiMAX\n");
return;
}
......@@ -1098,7 +1098,7 @@ void iwl_irq_tasklet(struct iwl_trans *trans)
handled |= CSR_INT_BIT_FH_TX;
/* Wake up uCode load routine, now that load is complete */
priv(trans)->ucode_write_complete = 1;
wake_up_interruptible(&trans->shrd->wait_command_queue);
wake_up(&trans->shrd->wait_command_queue);
}
if (inta & ~handled) {
......
......@@ -946,7 +946,7 @@ void iwl_tx_cmd_complete(struct iwl_trans *trans, struct iwl_rx_mem_buffer *rxb)
clear_bit(STATUS_HCMD_ACTIVE, &trans->shrd->status);
IWL_DEBUG_INFO(trans, "Clearing HCMD_ACTIVE for command %s\n",
get_cmd_string(cmd->hdr.cmd));
wake_up_interruptible(&trans->shrd->wait_command_queue);
wake_up(&trans->shrd->wait_command_queue);
}
meta->flags = 0;
......@@ -1032,7 +1032,7 @@ static int iwl_send_cmd_sync(struct iwl_trans *trans, struct iwl_host_cmd *cmd)
return ret;
}
ret = wait_event_interruptible_timeout(trans->shrd->wait_command_queue,
ret = wait_event_timeout(trans->shrd->wait_command_queue,
!test_bit(STATUS_HCMD_ACTIVE, &trans->shrd->status),
HOST_COMPLETE_TIMEOUT);
if (!ret) {
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment