Commit f35f6d8c authored by Mark Brown's avatar Mark Brown

Merge series "Really implement Qualcomm LAB/IBB regulators" from...

Merge series "Really implement Qualcomm LAB/IBB regulators" from AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>:

Okay, the title may be a little "aggressive"? However, the qcom-labibb
driver wasn't really .. doing much.
The current form of this driver is only taking care of enabling or
disabling the regulators, which is pretty useless if they were not
pre-set from the bootloader, which sets them only if continuous
splash is enabled.
Moreover, some bootloaders are setting a higher voltage and/or a higher
current limit compared to what's actually required by the attached
hardware (which is, in 99.9% of the cases, a display) and this produces
a higher power consumption, higher heat output and a risk of actually
burning the display if kept up for a very long time: for example, this
is true on at least some Sony Xperia MSM8998 (Yoshino platform) and
especially on some Sony Xperia SDM845 (Tama platform) smartphones.

In any case, the main reason why this change was necessary for us is
that, during the bringup of Sony Xperia MSM8998 phones, we had an issue
with the bootloader not turning on the display and not setting the lab
and ibb regulators before booting the kernel, making it impossible to
powerup the display.

With this said, this patchset enables setting voltage, current limiting,
overcurrent and short-circuit protection.. and others, on the LAB/IBB
regulators.
Each commit in this patch series provides as many informations as
possible about what's going on and testing methodology.

Changes in v2:
 - From Mark Brown review:
   - Replaced some if branches with switch statements
   - Moved irq get and request in probe function
   - Changed short conditionals to full ones
   - Removed useless check for ocp_irq_requested
 -  Fixed issues with YAML documentation

AngeloGioacchino Del Regno (7):
  regulator: qcom-labibb: Implement voltage selector ops
  regulator: qcom-labibb: Implement current limiting
  regulator: qcom-labibb: Implement pull-down, softstart, active
    discharge
  dt-bindings: regulator: qcom-labibb: Document soft start properties
  regulator: qcom-labibb: Implement short-circuit and over-current IRQs
  dt-bindings: regulator: qcom-labibb: Document SCP/OCP interrupts
  arm64: dts: pmi8998: Add the right interrupts for LAB/IBB SCP and OCP

 .../regulator/qcom-labibb-regulator.yaml      |  30 +-
 arch/arm64/boot/dts/qcom/pmi8998.dtsi         |   8 +-
 drivers/regulator/qcom-labibb-regulator.c     | 661 +++++++++++++++++-
 3 files changed, 686 insertions(+), 13 deletions(-)

--
2.29.2
parents 475a5d85 dd582369
...@@ -19,6 +19,12 @@ ...@@ -19,6 +19,12 @@
#define PMI8998_IBB_REG_BASE 0xdc00 #define PMI8998_IBB_REG_BASE 0xdc00
#define REG_LABIBB_STATUS1 0x08 #define REG_LABIBB_STATUS1 0x08
#define REG_LABIBB_VOLTAGE 0x41
#define LABIBB_VOLTAGE_OVERRIDE_EN BIT(7)
#define LAB_VOLTAGE_SET_MASK GENMASK(3, 0)
#define IBB_VOLTAGE_SET_MASK GENMASK(5, 0)
#define REG_LABIBB_ENABLE_CTL 0x46 #define REG_LABIBB_ENABLE_CTL 0x46
#define LABIBB_STATUS1_VREG_OK_BIT BIT(7) #define LABIBB_STATUS1_VREG_OK_BIT BIT(7)
#define LABIBB_CONTROL_ENABLE BIT(7) #define LABIBB_CONTROL_ENABLE BIT(7)
...@@ -51,6 +57,10 @@ static const struct regulator_ops qcom_labibb_ops = { ...@@ -51,6 +57,10 @@ static const struct regulator_ops qcom_labibb_ops = {
.enable = regulator_enable_regmap, .enable = regulator_enable_regmap,
.disable = regulator_disable_regmap, .disable = regulator_disable_regmap,
.is_enabled = regulator_is_enabled_regmap, .is_enabled = regulator_is_enabled_regmap,
.set_voltage_sel = regulator_set_voltage_sel_regmap,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.list_voltage = regulator_list_voltage_linear_range,
.map_voltage = regulator_map_voltage_linear_range,
}; };
static const struct regulator_desc pmi8998_lab_desc = { static const struct regulator_desc pmi8998_lab_desc = {
...@@ -59,9 +69,18 @@ static const struct regulator_desc pmi8998_lab_desc = { ...@@ -59,9 +69,18 @@ static const struct regulator_desc pmi8998_lab_desc = {
.enable_val = LABIBB_CONTROL_ENABLE, .enable_val = LABIBB_CONTROL_ENABLE,
.enable_time = LAB_ENABLE_TIME, .enable_time = LAB_ENABLE_TIME,
.poll_enabled_time = LABIBB_POLL_ENABLED_TIME, .poll_enabled_time = LABIBB_POLL_ENABLED_TIME,
.vsel_reg = (PMI8998_LAB_REG_BASE + REG_LABIBB_VOLTAGE),
.vsel_mask = LAB_VOLTAGE_SET_MASK,
.apply_reg = (PMI8998_LAB_REG_BASE + REG_LABIBB_VOLTAGE),
.apply_bit = LABIBB_VOLTAGE_OVERRIDE_EN,
.off_on_delay = LABIBB_OFF_ON_DELAY, .off_on_delay = LABIBB_OFF_ON_DELAY,
.owner = THIS_MODULE, .owner = THIS_MODULE,
.type = REGULATOR_VOLTAGE, .type = REGULATOR_VOLTAGE,
.linear_ranges = (struct linear_range[]) {
REGULATOR_LINEAR_RANGE(4600000, 0, 15, 100000),
},
.n_linear_ranges = 1,
.n_voltages = 16,
.ops = &qcom_labibb_ops, .ops = &qcom_labibb_ops,
}; };
...@@ -71,9 +90,18 @@ static const struct regulator_desc pmi8998_ibb_desc = { ...@@ -71,9 +90,18 @@ static const struct regulator_desc pmi8998_ibb_desc = {
.enable_val = LABIBB_CONTROL_ENABLE, .enable_val = LABIBB_CONTROL_ENABLE,
.enable_time = IBB_ENABLE_TIME, .enable_time = IBB_ENABLE_TIME,
.poll_enabled_time = LABIBB_POLL_ENABLED_TIME, .poll_enabled_time = LABIBB_POLL_ENABLED_TIME,
.vsel_reg = (PMI8998_IBB_REG_BASE + REG_LABIBB_VOLTAGE),
.vsel_mask = IBB_VOLTAGE_SET_MASK,
.apply_reg = (PMI8998_IBB_REG_BASE + REG_LABIBB_VOLTAGE),
.apply_bit = LABIBB_VOLTAGE_OVERRIDE_EN,
.off_on_delay = LABIBB_OFF_ON_DELAY, .off_on_delay = LABIBB_OFF_ON_DELAY,
.owner = THIS_MODULE, .owner = THIS_MODULE,
.type = REGULATOR_VOLTAGE, .type = REGULATOR_VOLTAGE,
.linear_ranges = (struct linear_range[]) {
REGULATOR_LINEAR_RANGE(1400000, 0, 63, 100000),
},
.n_linear_ranges = 1,
.n_voltages = 64,
.ops = &qcom_labibb_ops, .ops = &qcom_labibb_ops,
}; };
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment