Merge branch 'topic/st_fdma' of...

Merge branch 'topic/st_fdma' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/slave-dma into rproc-next

Documentation/devicetree/bindings/dma/st_fdma.txt

+* STMicroelectronics Flexible Direct Memory Access Device Tree bindings
+
+The FDMA is a general-purpose direct memory access controller capable of
+supporting 16 independent DMA channels. It accepts up to 32 DMA requests.
+The FDMA is based on a Slim processor which requires a firmware.
+
+* FDMA Controller
+
+Required properties:
+- compatible	: Should be one of
+		 - st,stih407-fdma-mpe31-11, "st,slim-rproc";
+		 - st,stih407-fdma-mpe31-12, "st,slim-rproc";
+		 - st,stih407-fdma-mpe31-13, "st,slim-rproc";
+- reg		: Should contain an entry for each name in reg-names
+- reg-names	: Must contain "slimcore", "dmem", "peripherals", "imem" entries
+- interrupts	: Should contain one interrupt shared by all channels
+- dma-channels	: Number of channels supported by the controller
+- #dma-cells	: Must be <3>. See DMA client section below
+- clocks	: Must contain an entry for each clock
+See: Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+
+Example:
+
+	fdma0: dma-controller@8e20000 {
+		compatible = "st,stih407-fdma-mpe31-11", "st,slim-rproc";
+		reg = <0x8e20000 0x8000>,
+		      <0x8e30000 0x3000>,
+		      <0x8e37000 0x1000>,
+		      <0x8e38000 0x8000>;
+		reg-names = "slimcore", "dmem", "peripherals", "imem";
+		clocks = <&clk_s_c0_flexgen CLK_FDMA>,
+			 <&clk_s_c0_flexgen CLK_EXT2F_A9>,
+			 <&clk_s_c0_flexgen CLK_EXT2F_A9>,
+			 <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+		interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>;
+		dma-channels = <16>;
+		#dma-cells = <3>;
+	};
+
+* DMA client
+
+Required properties:
+- dmas: Comma separated list of dma channel requests
+- dma-names: Names of the aforementioned requested channels
+
+Each dmas request consists of 4 cells:
+1. A phandle pointing to the FDMA controller
+2. The request line number
+3. A 32bit mask specifying (see include/linux/platform_data/dma-st-fdma.h)
+ -bit 2-0: Holdoff value, dreq will be masked for
+	0x0: 0-0.5us
+	0x1: 0.5-1us
+	0x2: 1-1.5us
+ -bit 17: data swap
+	0x0: disabled
+	0x1: enabled
+ -bit 21: Increment Address
+	0x0: no address increment between transfers
+	0x1: increment address between transfers
+ -bit 22: 2 STBus Initiator Coprocessor interface
+	0x0: high priority port
+	0x1: low priority port
+4. transfers type
+ 0 free running
+ 1 paced
+
+Example:
+
+	sti_uni_player2: sti-uni-player@2 {
+		compatible = "st,sti-uni-player";
+		status = "disabled";
+		#sound-dai-cells = <0>;
+		st,syscfg = <&syscfg_core>;
+		clocks = <&clk_s_d0_flexgen CLK_PCM_2>;
+		assigned-clocks = <&clk_s_d0_flexgen CLK_PCM_2>;
+		assigned-clock-parents = <&clk_s_d0_quadfs 2>;
+		assigned-clock-rates = <50000000>;
+		reg = <0x8D82000 0x158>;
+		interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
+		dmas = <&fdma0 4 0 1>;
+		dai-name = "Uni Player #1 (DAC)";
+		dma-names = "tx";
+		st,uniperiph-id = <2>;
+		st,version = <5>;
+		st,mode = "PCM";
+	};

MAINTAINERS

@@ -1774,6 +1774,7 @@ F:	drivers/char/hw_random/st-rng.c
 F:	drivers/clocksource/arm_global_timer.c
 F:	drivers/clocksource/clksrc_st_lpc.c
 F:	drivers/cpufreq/sti-cpufreq.c
+F:	drivers/dma/st_fdma*
 F:	drivers/i2c/busses/i2c-st.c
 F:	drivers/media/rc/st_rc.c
 F:	drivers/media/platform/sti/c8sectpfe/
@@ -1784,6 +1785,7 @@ F:	drivers/phy/phy-stih407-usb.c
 F:	drivers/phy/phy-stih41x-usb.c
 F:	drivers/pinctrl/pinctrl-st.c
 F:	drivers/remoteproc/st_remoteproc.c
+F:	drivers/remoteproc/st_slim_rproc.c
 F:	drivers/reset/sti/
 F:	drivers/rtc/rtc-st-lpc.c
 F:	drivers/tty/serial/st-asc.c
@@ -1792,6 +1794,7 @@ F:	drivers/usb/host/ehci-st.c
 F:	drivers/usb/host/ohci-st.c
 F:	drivers/watchdog/st_lpc_wdt.c
 F:	drivers/ata/ahci_st.c
+F:	include/linux/remoteproc/st_slim_rproc.h
 
 ARM/STM32 ARCHITECTURE
 M:	Maxime Coquelin <mcoquelin.stm32@gmail.com>

arch/arm/configs/multi_v7_defconfig

@@ -649,6 +649,9 @@ CONFIG_SND_SOC_AK4642=m
 CONFIG_SND_SOC_SGTL5000=m
 CONFIG_SND_SOC_SPDIF=m
 CONFIG_SND_SOC_WM8978=m
+CONFIG_SND_SOC_STI=m
+CONFIG_SND_SOC_STI_SAS=m
+CONFIG_SND_SIMPLE_CARD=m
 CONFIG_USB=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_MVEBU=y
@@ -790,6 +793,7 @@ CONFIG_DMA_OMAP=y
 CONFIG_QCOM_BAM_DMA=y
 CONFIG_XILINX_DMA=y
 CONFIG_DMA_SUN6I=y
+CONFIG_ST_FDMA=m
 CONFIG_STAGING=y
 CONFIG_SENSORS_ISL29018=y
 CONFIG_SENSORS_ISL29028=y
@@ -823,6 +827,8 @@ CONFIG_HWSPINLOCK_QCOM=y
 CONFIG_ROCKCHIP_IOMMU=y
 CONFIG_TEGRA_IOMMU_GART=y
 CONFIG_TEGRA_IOMMU_SMMU=y
+CONFIG_REMOTEPROC=m
+CONFIG_ST_REMOTEPROC=m
 CONFIG_PM_DEVFREQ=y
 CONFIG_ARM_TEGRA_DEVFREQ=m
 CONFIG_MEMORY=y

drivers/dma/Kconfig

@@ -435,6 +435,19 @@ config STE_DMA40
 	help
 	  Support for ST-Ericsson DMA40 controller
 
+config ST_FDMA
+	tristate "ST FDMA dmaengine support"
+	depends on ARCH_STI
+	select ST_SLIM_REMOTEPROC
+	select DMA_ENGINE
+	select DMA_VIRTUAL_CHANNELS
+	help
+	  Enable support for ST FDMA controller.
+	  It supports 16 independent DMA channels, accepts up to 32 DMA requests
+
+	  Say Y here if you have such a chipset.
+	  If unsure, say N.
+
 config STM32_DMA
 	bool "STMicroelectronics STM32 DMA support"
 	depends on ARCH_STM32 || COMPILE_TEST

drivers/dma/Makefile

@@ -67,6 +67,7 @@ obj-$(CONFIG_TI_DMA_CROSSBAR) += ti-dma-crossbar.o
 obj-$(CONFIG_TI_EDMA) += edma.o
 obj-$(CONFIG_XGENE_DMA) += xgene-dma.o
 obj-$(CONFIG_ZX_DMA) += zx296702_dma.o
+obj-$(CONFIG_ST_FDMA) += st_fdma.o
 
 obj-y += qcom/
 obj-y += xilinx/

drivers/dma/st_fdma.h

+/*
+ * DMA driver header for STMicroelectronics STi FDMA controller
+ *
+ * Copyright (C) 2014 STMicroelectronics
+ *
+ * Author: Ludovic Barre <Ludovic.barre@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef __DMA_ST_FDMA_H
+#define __DMA_ST_FDMA_H
+
+#include <linux/dmaengine.h>
+#include <linux/dmapool.h>
+#include <linux/io.h>
+#include <linux/remoteproc/st_slim_rproc.h>
+#include "virt-dma.h"
+
+#define ST_FDMA_NR_DREQS 32
+#define FW_NAME_SIZE 30
+#define DRIVER_NAME "st-fdma"
+
+/**
+ * struct st_fdma_generic_node - Free running/paced generic node
+ *
+ * @length: Length in bytes of a line in a 2D mem to mem
+ * @sstride: Stride, in bytes, between source lines in a 2D data move
+ * @dstride: Stride, in bytes, between destination lines in a 2D data move
+ */
+struct st_fdma_generic_node {
+	u32 length;
+	u32 sstride;
+	u32 dstride;
+};
+
+/**
+ * struct st_fdma_hw_node - Node structure used by fdma hw
+ *
+ * @next: Pointer to next node
+ * @control: Transfer Control Parameters
+ * @nbytes: Number of Bytes to read
+ * @saddr: Source address
+ * @daddr: Destination address
+ *
+ * @generic: generic node for free running/paced transfert type
+ * 2 others transfert type are possible, but not yet implemented
+ *
+ * The NODE structures must be aligned to a 32 byte boundary
+ */
+struct st_fdma_hw_node {
+	u32 next;
+	u32 control;
+	u32 nbytes;
+	u32 saddr;
+	u32 daddr;
+	union {
+		struct st_fdma_generic_node generic;
+	};
+} __aligned(32);
+
+/*
+ * node control parameters
+ */
+#define FDMA_NODE_CTRL_REQ_MAP_MASK	GENMASK(4, 0)
+#define FDMA_NODE_CTRL_REQ_MAP_FREE_RUN	0x0
+#define FDMA_NODE_CTRL_REQ_MAP_DREQ(n)	((n)&FDMA_NODE_CTRL_REQ_MAP_MASK)
+#define FDMA_NODE_CTRL_REQ_MAP_EXT		FDMA_NODE_CTRL_REQ_MAP_MASK
+#define FDMA_NODE_CTRL_SRC_MASK		GENMASK(6, 5)
+#define FDMA_NODE_CTRL_SRC_STATIC	BIT(5)
+#define FDMA_NODE_CTRL_SRC_INCR		BIT(6)
+#define FDMA_NODE_CTRL_DST_MASK		GENMASK(8, 7)
+#define FDMA_NODE_CTRL_DST_STATIC	BIT(7)
+#define FDMA_NODE_CTRL_DST_INCR		BIT(8)
+#define FDMA_NODE_CTRL_SECURE		BIT(15)
+#define FDMA_NODE_CTRL_PAUSE_EON	BIT(30)
+#define FDMA_NODE_CTRL_INT_EON		BIT(31)
+
+/**
+ * struct st_fdma_sw_node - descriptor structure for link list
+ *
+ * @pdesc: Physical address of desc
+ * @node: link used for putting this into a channel queue
+ */
+struct st_fdma_sw_node {
+	dma_addr_t pdesc;
+	struct st_fdma_hw_node *desc;
+};
+
+#define NAME_SZ 10
+
+struct st_fdma_driverdata {
+	u32 id;
+	char name[NAME_SZ];
+};
+
+struct st_fdma_desc {
+	struct virt_dma_desc vdesc;
+	struct st_fdma_chan *fchan;
+	bool iscyclic;
+	unsigned int n_nodes;
+	struct st_fdma_sw_node node[];
+};
+
+enum st_fdma_type {
+	ST_FDMA_TYPE_FREE_RUN,
+	ST_FDMA_TYPE_PACED,
+};
+
+struct st_fdma_cfg {
+	struct device_node *of_node;
+	enum st_fdma_type type;
+	dma_addr_t dev_addr;
+	enum dma_transfer_direction dir;
+	int req_line; /* request line */
+	long req_ctrl; /* Request control */
+};
+
+struct st_fdma_chan {
+	struct st_fdma_dev *fdev;
+	struct dma_pool *node_pool;
+	struct dma_slave_config scfg;
+	struct st_fdma_cfg cfg;
+
+	int dreq_line;
+
+	struct virt_dma_chan vchan;
+	struct st_fdma_desc *fdesc;
+	enum dma_status	status;
+};
+
+struct st_fdma_dev {
+	struct device *dev;
+	const struct st_fdma_driverdata *drvdata;
+	struct dma_device dma_device;
+
+	struct st_slim_rproc *slim_rproc;
+
+	int irq;
+
+	struct st_fdma_chan *chans;
+
+	spinlock_t dreq_lock;
+	unsigned long dreq_mask;
+
+	u32 nr_channels;
+	char fw_name[FW_NAME_SIZE];
+};
+
+/* Peripheral Registers*/
+
+#define FDMA_CMD_STA_OFST	0xFC0
+#define FDMA_CMD_SET_OFST	0xFC4
+#define FDMA_CMD_CLR_OFST	0xFC8
+#define FDMA_CMD_MASK_OFST	0xFCC
+#define FDMA_CMD_START(ch)		(0x1 << (ch << 1))
+#define FDMA_CMD_PAUSE(ch)		(0x2 << (ch << 1))
+#define FDMA_CMD_FLUSH(ch)		(0x3 << (ch << 1))
+
+#define FDMA_INT_STA_OFST	0xFD0
+#define FDMA_INT_STA_CH			0x1
+#define FDMA_INT_STA_ERR		0x2
+
+#define FDMA_INT_SET_OFST	0xFD4
+#define FDMA_INT_CLR_OFST	0xFD8
+#define FDMA_INT_MASK_OFST	0xFDC
+
+#define fdma_read(fdev, name) \
+	readl((fdev)->slim_rproc->peri + name)
+
+#define fdma_write(fdev, val, name) \
+	writel((val), (fdev)->slim_rproc->peri + name)
+
+/* fchan interface (dmem) */
+#define FDMA_CH_CMD_OFST	0x200
+#define FDMA_CH_CMD_STA_MASK		GENMASK(1, 0)
+#define FDMA_CH_CMD_STA_IDLE		(0x0)
+#define FDMA_CH_CMD_STA_START		(0x1)
+#define FDMA_CH_CMD_STA_RUNNING		(0x2)
+#define FDMA_CH_CMD_STA_PAUSED		(0x3)
+#define FDMA_CH_CMD_ERR_MASK		GENMASK(4, 2)
+#define FDMA_CH_CMD_ERR_INT		(0x0 << 2)
+#define FDMA_CH_CMD_ERR_NAND		(0x1 << 2)
+#define FDMA_CH_CMD_ERR_MCHI		(0x2 << 2)
+#define FDMA_CH_CMD_DATA_MASK		GENMASK(31, 5)
+#define fchan_read(fchan, name) \
+	readl((fchan)->fdev->slim_rproc->mem[ST_SLIM_DMEM].cpu_addr \
+			+ (fchan)->vchan.chan.chan_id * 0x4 \
+			+ name)
+
+#define fchan_write(fchan, val, name) \
+	writel((val), (fchan)->fdev->slim_rproc->mem[ST_SLIM_DMEM].cpu_addr \
+			+ (fchan)->vchan.chan.chan_id * 0x4 \
+			+ name)
+
+/* req interface */
+#define FDMA_REQ_CTRL_OFST	0x240
+#define dreq_write(fchan, val, name) \
+	writel((val), (fchan)->fdev->slim_rproc->mem[ST_SLIM_DMEM].cpu_addr \
+			+ fchan->dreq_line * 0x04 \
+			+ name)
+/* node interface */
+#define FDMA_NODE_SZ 128
+#define FDMA_PTRN_OFST		0x800
+#define FDMA_CNTN_OFST		0x808
+#define FDMA_SADDRN_OFST	0x80c
+#define FDMA_DADDRN_OFST	0x810
+#define fnode_read(fchan, name) \
+	readl((fchan)->fdev->slim_rproc->mem[ST_SLIM_DMEM].cpu_addr \
+			+ (fchan)->vchan.chan.chan_id * FDMA_NODE_SZ \
+			+ name)
+
+#define fnode_write(fchan, val, name) \
+	writel((val), (fchan)->fdev->slim_rproc->mem[ST_SLIM_DMEM].cpu_addr \
+			+ (fchan)->vchan.chan.chan_id * FDMA_NODE_SZ \
+			+ name)
+
+/*
+ * request control bits
+ */
+#define FDMA_REQ_CTRL_NUM_OPS_MASK	GENMASK(31, 24)
+#define FDMA_REQ_CTRL_NUM_OPS(n)	(FDMA_REQ_CTRL_NUM_OPS_MASK & \
+					((n) << 24))
+#define FDMA_REQ_CTRL_INITIATOR_MASK	BIT(22)
+#define FDMA_REQ_CTRL_INIT0		(0x0 << 22)
+#define FDMA_REQ_CTRL_INIT1		(0x1 << 22)
+#define FDMA_REQ_CTRL_INC_ADDR_ON	BIT(21)
+#define FDMA_REQ_CTRL_DATA_SWAP_ON	BIT(17)
+#define FDMA_REQ_CTRL_WNR		BIT(14)
+#define FDMA_REQ_CTRL_OPCODE_MASK	GENMASK(7, 4)
+#define FDMA_REQ_CTRL_OPCODE_LD_ST1	(0x0 << 4)
+#define FDMA_REQ_CTRL_OPCODE_LD_ST2	(0x1 << 4)
+#define FDMA_REQ_CTRL_OPCODE_LD_ST4	(0x2 << 4)
+#define FDMA_REQ_CTRL_OPCODE_LD_ST8	(0x3 << 4)
+#define FDMA_REQ_CTRL_OPCODE_LD_ST16	(0x4 << 4)
+#define FDMA_REQ_CTRL_OPCODE_LD_ST32	(0x5 << 4)
+#define FDMA_REQ_CTRL_OPCODE_LD_ST64	(0x6 << 4)
+#define FDMA_REQ_CTRL_HOLDOFF_MASK	GENMASK(2, 0)
+#define FDMA_REQ_CTRL_HOLDOFF(n)	((n) & FDMA_REQ_CTRL_HOLDOFF_MASK)
+
+/* bits used by client to configure request control */
+#define FDMA_REQ_CTRL_CFG_MASK (FDMA_REQ_CTRL_HOLDOFF_MASK | \
+				FDMA_REQ_CTRL_DATA_SWAP_ON | \
+				FDMA_REQ_CTRL_INC_ADDR_ON | \
+				FDMA_REQ_CTRL_INITIATOR_MASK)
+
+#endif	/* __DMA_ST_FDMA_H */

drivers/remoteproc/Kconfig

 menu "Remoteproc drivers"
 
-# REMOTEPROC gets selected by whoever wants it
 config REMOTEPROC
-	tristate
+	tristate "Support for Remote Processor subsystem"
 	depends on HAS_DMA
 	select CRC32
 	select FW_LOADER
 	select VIRTIO
 	select VIRTUALIZATION
 
+if REMOTEPROC
+
 config OMAP_REMOTEPROC
 	tristate "OMAP remoteproc support"
 	depends on HAS_DMA
 	depends on ARCH_OMAP4 || SOC_OMAP5
 	depends on OMAP_IOMMU
-	select REMOTEPROC
+	depends on REMOTEPROC
 	select MAILBOX
 	select OMAP2PLUS_MBOX
 	select RPMSG_VIRTIO
@@ -34,7 +35,7 @@ config OMAP_REMOTEPROC
 config STE_MODEM_RPROC
 	tristate "STE-Modem remoteproc support"
 	depends on HAS_DMA
-	select REMOTEPROC
+	depends on REMOTEPROC
 	default n
 	help
 	  Say y or m here to support STE-Modem shared memory driver.
@@ -44,7 +45,7 @@ config STE_MODEM_RPROC
 config WKUP_M3_RPROC
 	tristate "AMx3xx Wakeup M3 remoteproc support"
 	depends on SOC_AM33XX || SOC_AM43XX
-	select REMOTEPROC
+	depends on REMOTEPROC
 	help
 	  Say y here to support Wakeup M3 remote processor on TI AM33xx
 	  and AM43xx family of SoCs.
@@ -57,8 +58,8 @@ config WKUP_M3_RPROC
 config DA8XX_REMOTEPROC
 	tristate "DA8xx/OMAP-L13x remoteproc support"
 	depends on ARCH_DAVINCI_DA8XX
+	depends on REMOTEPROC
 	select CMA if MMU
-	select REMOTEPROC
 	select RPMSG_VIRTIO
 	help
 	  Say y here to support DA8xx/OMAP-L13x remote processors via the
@@ -95,9 +96,9 @@ config QCOM_Q6V5_PIL
 	tristate "Qualcomm Hexagon V5 Peripherial Image Loader"
 	depends on OF && ARCH_QCOM
 	depends on QCOM_SMEM
+	depends on REMOTEPROC
 	select MFD_SYSCON
 	select QCOM_MDT_LOADER
-	select REMOTEPROC
 	help
 	  Say y here to support the Qualcomm Peripherial Image Loader for the
 	  Hexagon V5 based remote processors.
@@ -106,9 +107,9 @@ config QCOM_WCNSS_PIL
 	tristate "Qualcomm WCNSS Peripheral Image Loader"
 	depends on OF && ARCH_QCOM
 	depends on QCOM_SMEM
+	depends on REMOTEPROC
 	select QCOM_MDT_LOADER
 	select QCOM_SCM
-	select REMOTEPROC
 	help
 	  Say y here to support the Peripheral Image Loader for the Qualcomm
 	  Wireless Connectivity Subsystem.
@@ -116,10 +117,16 @@ config QCOM_WCNSS_PIL
 config ST_REMOTEPROC
 	tristate "ST remoteproc support"
 	depends on ARCH_STI
-	select REMOTEPROC
+	depends on REMOTEPROC
 	help
 	  Say y here to support ST's adjunct processors via the remote
 	  processor framework.
 	  This can be either built-in or a loadable module.
 
+config ST_SLIM_REMOTEPROC
+	tristate
+	depends on REMOTEPROC
+
+endif # REMOTEPROC
+
 endmenu

drivers/remoteproc/Makefile

@@ -19,3 +19,4 @@ obj-$(CONFIG_QCOM_WCNSS_PIL)		+= qcom_wcnss_pil.o
 qcom_wcnss_pil-y			+= qcom_wcnss.o
 qcom_wcnss_pil-y			+= qcom_wcnss_iris.o
 obj-$(CONFIG_ST_REMOTEPROC)		+= st_remoteproc.o
+obj-$(CONFIG_ST_SLIM_REMOTEPROC)	+= st_slim_rproc.o

drivers/remoteproc/st_slim_rproc.c

+/*
+ * SLIM core rproc driver
+ *
+ * Copyright (C) 2016 STMicroelectronics
+ *
+ * Author: Peter Griffin <peter.griffin@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/remoteproc.h>
+#include <linux/remoteproc/st_slim_rproc.h>
+#include "remoteproc_internal.h"
+
+/* SLIM core registers */
+#define SLIM_ID_OFST		0x0
+#define SLIM_VER_OFST		0x4
+
+#define SLIM_EN_OFST		0x8
+#define SLIM_EN_RUN			BIT(0)
+
+#define SLIM_CLK_GATE_OFST	0xC
+#define SLIM_CLK_GATE_DIS		BIT(0)
+#define SLIM_CLK_GATE_RESET		BIT(2)
+
+#define SLIM_SLIM_PC_OFST	0x20
+
+/* DMEM registers */
+#define SLIM_REV_ID_OFST	0x0
+#define SLIM_REV_ID_MIN_MASK		GENMASK(15, 8)
+#define SLIM_REV_ID_MIN(id)		((id & SLIM_REV_ID_MIN_MASK) >> 8)
+#define SLIM_REV_ID_MAJ_MASK		GENMASK(23, 16)
+#define SLIM_REV_ID_MAJ(id)		((id & SLIM_REV_ID_MAJ_MASK) >> 16)
+
+
+/* peripherals registers */
+#define SLIM_STBUS_SYNC_OFST	0xF88
+#define SLIM_STBUS_SYNC_DIS		BIT(0)
+
+#define SLIM_INT_SET_OFST	0xFD4
+#define SLIM_INT_CLR_OFST	0xFD8
+#define SLIM_INT_MASK_OFST	0xFDC
+
+#define SLIM_CMD_CLR_OFST	0xFC8
+#define SLIM_CMD_MASK_OFST	0xFCC
+
+static const char *mem_names[ST_SLIM_MEM_MAX] = {
+	[ST_SLIM_DMEM]	= "dmem",
+	[ST_SLIM_IMEM]	= "imem",
+};
+
+static int slim_clk_get(struct st_slim_rproc *slim_rproc, struct device *dev)
+{
+	int clk, err;
+
+	for (clk = 0; clk < ST_SLIM_MAX_CLK; clk++) {
+		slim_rproc->clks[clk] = of_clk_get(dev->of_node, clk);
+		if (IS_ERR(slim_rproc->clks[clk])) {
+			err = PTR_ERR(slim_rproc->clks[clk]);
+			if (err == -EPROBE_DEFER)
+				goto err_put_clks;
+			slim_rproc->clks[clk] = NULL;
+			break;
+		}
+	}
+
+	return 0;
+
+err_put_clks:
+	while (--clk >= 0)
+		clk_put(slim_rproc->clks[clk]);
+
+	return err;
+}
+
+static void slim_clk_disable(struct st_slim_rproc *slim_rproc)
+{
+	int clk;
+
+	for (clk = 0; clk < ST_SLIM_MAX_CLK && slim_rproc->clks[clk]; clk++)
+		clk_disable_unprepare(slim_rproc->clks[clk]);
+}
+
+static int slim_clk_enable(struct st_slim_rproc *slim_rproc)
+{
+	int clk, ret;
+
+	for (clk = 0; clk < ST_SLIM_MAX_CLK && slim_rproc->clks[clk]; clk++) {
+		ret = clk_prepare_enable(slim_rproc->clks[clk]);
+		if (ret)
+			goto err_disable_clks;
+	}
+
+	return 0;
+
+err_disable_clks:
+	while (--clk >= 0)
+		clk_disable_unprepare(slim_rproc->clks[clk]);
+
+	return ret;
+}
+
+/*
+ * Remoteproc slim specific device handlers
+ */
+static int slim_rproc_start(struct rproc *rproc)
+{
+	struct device *dev = &rproc->dev;
+	struct st_slim_rproc *slim_rproc = rproc->priv;
+	unsigned long hw_id, hw_ver, fw_rev;
+	u32 val;
+
+	/* disable CPU pipeline clock & reset CPU pipeline */
+	val = SLIM_CLK_GATE_DIS | SLIM_CLK_GATE_RESET;
+	writel(val, slim_rproc->slimcore + SLIM_CLK_GATE_OFST);
+
+	/* disable SLIM core STBus sync */
+	writel(SLIM_STBUS_SYNC_DIS, slim_rproc->peri + SLIM_STBUS_SYNC_OFST);
+
+	/* enable cpu pipeline clock */
+	writel(!SLIM_CLK_GATE_DIS,
+		slim_rproc->slimcore + SLIM_CLK_GATE_OFST);
+
+	/* clear int & cmd mailbox */
+	writel(~0U, slim_rproc->peri + SLIM_INT_CLR_OFST);
+	writel(~0U, slim_rproc->peri + SLIM_CMD_CLR_OFST);
+
+	/* enable all channels cmd & int */
+	writel(~0U, slim_rproc->peri + SLIM_INT_MASK_OFST);
+	writel(~0U, slim_rproc->peri + SLIM_CMD_MASK_OFST);
+
+	/* enable cpu */
+	writel(SLIM_EN_RUN, slim_rproc->slimcore + SLIM_EN_OFST);
+
+	hw_id = readl_relaxed(slim_rproc->slimcore + SLIM_ID_OFST);
+	hw_ver = readl_relaxed(slim_rproc->slimcore + SLIM_VER_OFST);
+
+	fw_rev = readl(slim_rproc->mem[ST_SLIM_DMEM].cpu_addr +
+			SLIM_REV_ID_OFST);
+
+	dev_info(dev, "fw rev:%ld.%ld on SLIM %ld.%ld\n",
+		 SLIM_REV_ID_MAJ(fw_rev), SLIM_REV_ID_MIN(fw_rev),
+		 hw_id, hw_ver);
+
+	return 0;
+}
+
+static int slim_rproc_stop(struct rproc *rproc)
+{
+	struct st_slim_rproc *slim_rproc = rproc->priv;
+	u32 val;
+
+	/* mask all (cmd & int) channels */
+	writel(0UL, slim_rproc->peri + SLIM_INT_MASK_OFST);
+	writel(0UL, slim_rproc->peri + SLIM_CMD_MASK_OFST);
+
+	/* disable cpu pipeline clock */
+	writel(SLIM_CLK_GATE_DIS, slim_rproc->slimcore + SLIM_CLK_GATE_OFST);
+
+	writel(!SLIM_EN_RUN, slim_rproc->slimcore + SLIM_EN_OFST);
+
+	val = readl(slim_rproc->slimcore + SLIM_EN_OFST);
+	if (val & SLIM_EN_RUN)
+		dev_warn(&rproc->dev, "Failed to disable SLIM");
+
+	dev_dbg(&rproc->dev, "slim stopped\n");
+
+	return 0;
+}
+
+static void *slim_rproc_da_to_va(struct rproc *rproc, u64 da, int len)
+{
+	struct st_slim_rproc *slim_rproc = rproc->priv;
+	void *va = NULL;
+	int i;
+
+	for (i = 0; i < ST_SLIM_MEM_MAX; i++) {
+		if (da != slim_rproc->mem[i].bus_addr)
+			continue;
+
+		if (len <= slim_rproc->mem[i].size) {
+			/* __force to make sparse happy with type conversion */
+			va = (__force void *)slim_rproc->mem[i].cpu_addr;
+			break;
+		}
+	}
+
+	dev_dbg(&rproc->dev, "da = 0x%llx len = 0x%x va = 0x%p\n", da, len, va);
+
+	return va;
+}
+
+static struct rproc_ops slim_rproc_ops = {
+	.start		= slim_rproc_start,
+	.stop		= slim_rproc_stop,
+	.da_to_va       = slim_rproc_da_to_va,
+};
+
+/*
+ * Firmware handler operations: sanity, boot address, load ...
+ */
+
+static struct resource_table empty_rsc_tbl = {
+	.ver = 1,
+	.num = 0,
+};
+
+static struct resource_table *slim_rproc_find_rsc_table(struct rproc *rproc,
+					       const struct firmware *fw,
+					       int *tablesz)
+{
+	*tablesz = sizeof(empty_rsc_tbl);
+	return &empty_rsc_tbl;
+}
+
+static struct rproc_fw_ops slim_rproc_fw_ops = {
+	.find_rsc_table = slim_rproc_find_rsc_table,
+};
+
+/**
+ * st_slim_rproc_alloc() - allocate and initialise slim rproc
+ * @pdev: Pointer to the platform_device struct
+ * @fw_name: Name of firmware for rproc to use
+ *
+ * Function for allocating and initialising a slim rproc for use by
+ * device drivers whose IP is based around the SLIM core. It
+ * obtains and enables any clocks required by the SLIM core and also
+ * ioremaps the various IO.
+ *
+ * Returns st_slim_rproc pointer or PTR_ERR() on error.
+ */
+
+struct st_slim_rproc *st_slim_rproc_alloc(struct platform_device *pdev,
+				char *fw_name)
+{
+	struct device *dev = &pdev->dev;
+	struct st_slim_rproc *slim_rproc;
+	struct device_node *np = dev->of_node;
+	struct rproc *rproc;
+	struct resource *res;
+	int err, i;
+	const struct rproc_fw_ops *elf_ops;
+
+	if (!fw_name)
+		return ERR_PTR(-EINVAL);
+
+	if (!of_device_is_compatible(np, "st,slim-rproc"))
+		return ERR_PTR(-EINVAL);
+
+	rproc = rproc_alloc(dev, np->name, &slim_rproc_ops,
+			fw_name, sizeof(*slim_rproc));
+	if (!rproc)
+		return ERR_PTR(-ENOMEM);
+
+	rproc->has_iommu = false;
+
+	slim_rproc = rproc->priv;
+	slim_rproc->rproc = rproc;
+
+	elf_ops = rproc->fw_ops;
+	/* Use some generic elf ops */
+	slim_rproc_fw_ops.load = elf_ops->load;
+	slim_rproc_fw_ops.sanity_check = elf_ops->sanity_check;
+
+	rproc->fw_ops = &slim_rproc_fw_ops;
+
+	/* get imem and dmem */
+	for (i = 0; i < ARRAY_SIZE(mem_names); i++) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						mem_names[i]);
+
+		slim_rproc->mem[i].cpu_addr = devm_ioremap_resource(dev, res);
+		if (IS_ERR(slim_rproc->mem[i].cpu_addr)) {
+			dev_err(&pdev->dev, "devm_ioremap_resource failed\n");
+			err = PTR_ERR(slim_rproc->mem[i].cpu_addr);
+			goto err;
+		}
+		slim_rproc->mem[i].bus_addr = res->start;
+		slim_rproc->mem[i].size = resource_size(res);
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "slimcore");
+	slim_rproc->slimcore = devm_ioremap_resource(dev, res);
+	if (IS_ERR(slim_rproc->slimcore)) {
+		dev_err(&pdev->dev, "failed to ioremap slimcore IO\n");
+		err = PTR_ERR(slim_rproc->slimcore);
+		goto err;
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "peripherals");
+	slim_rproc->peri = devm_ioremap_resource(dev, res);
+	if (IS_ERR(slim_rproc->peri)) {
+		dev_err(&pdev->dev, "failed to ioremap peripherals IO\n");
+		err = PTR_ERR(slim_rproc->peri);
+		goto err;
+	}
+
+	err = slim_clk_get(slim_rproc, dev);
+	if (err)
+		goto err;
+
+	err = slim_clk_enable(slim_rproc);
+	if (err) {
+		dev_err(dev, "Failed to enable clocks\n");
+		goto err_clk_put;
+	}
+
+	/* Register as a remoteproc device */
+	err = rproc_add(rproc);
+	if (err) {
+		dev_err(dev, "registration of slim remoteproc failed\n");
+		goto err_clk_dis;
+	}
+
+	return slim_rproc;
+
+err_clk_dis:
+	slim_clk_disable(slim_rproc);
+err_clk_put:
+	for (i = 0; i < ST_SLIM_MAX_CLK && slim_rproc->clks[i]; i++)
+		clk_put(slim_rproc->clks[i]);
+err:
+	rproc_put(rproc);
+	return ERR_PTR(err);
+}
+EXPORT_SYMBOL(st_slim_rproc_alloc);
+
+/**
+  * st_slim_rproc_put() - put slim rproc resources
+  * @slim_rproc: Pointer to the st_slim_rproc struct
+  *
+  * Function for calling respective _put() functions on slim_rproc resources.
+  *
+  */
+void st_slim_rproc_put(struct st_slim_rproc *slim_rproc)
+{
+	int clk;
+
+	if (!slim_rproc)
+		return;
+
+	slim_clk_disable(slim_rproc);
+
+	for (clk = 0; clk < ST_SLIM_MAX_CLK && slim_rproc->clks[clk]; clk++)
+		clk_put(slim_rproc->clks[clk]);
+
+	rproc_del(slim_rproc->rproc);
+	rproc_put(slim_rproc->rproc);
+}
+EXPORT_SYMBOL(st_slim_rproc_put);
+
+MODULE_AUTHOR("Peter Griffin <peter.griffin@linaro.org>");
+MODULE_DESCRIPTION("STMicroelectronics SLIM core rproc driver");
+MODULE_LICENSE("GPL v2");

include/linux/remoteproc/st_slim_rproc.h

+/*
+ * SLIM core rproc driver header
+ *
+ * Copyright (C) 2016 STMicroelectronics
+ *
+ * Author: Peter Griffin <peter.griffin@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+#ifndef _ST_REMOTEPROC_SLIM_H
+#define _ST_REMOTEPROC_SLIM_H
+
+#define ST_SLIM_MEM_MAX 2
+#define ST_SLIM_MAX_CLK 4
+
+enum {
+	ST_SLIM_DMEM,
+	ST_SLIM_IMEM,
+};
+
+/**
+ * struct st_slim_mem - slim internal memory structure
+ * @cpu_addr: MPU virtual address of the memory region
+ * @bus_addr: Bus address used to access the memory region
+ * @size: Size of the memory region
+ */
+struct st_slim_mem {
+	void __iomem *cpu_addr;
+	phys_addr_t bus_addr;
+	size_t size;
+};
+
+/**
+ * struct st_slim_rproc - SLIM slim core
+ * @rproc: rproc handle
+ * @mem: slim memory information
+ * @slimcore: slim slimcore regs
+ * @peri: slim peripheral regs
+ * @clks: slim clocks
+ */
+struct st_slim_rproc {
+	struct rproc *rproc;
+	struct st_slim_mem mem[ST_SLIM_MEM_MAX];
+	void __iomem *slimcore;
+	void __iomem *peri;
+
+	/* st_slim_rproc private */
+	struct clk *clks[ST_SLIM_MAX_CLK];
+};
+
+struct st_slim_rproc *st_slim_rproc_alloc(struct platform_device *pdev,
+					char *fw_name);
+void st_slim_rproc_put(struct st_slim_rproc *slim_rproc);
+
+#endif