Merge tag 'v4.17-rockchip-dts64-1' of...

Merge tag 'v4.17-rockchip-dts64-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Pull "Rockchip dts64 changes for 4.17" from Heiko Stübner:

The rk3399 gained support its Cadence displayport controller and some
minor additions like pins for 2ch i2s0 and the cif test clocks as well
as a default rate for ACLK_VIO that should be 400MHz according to the TRM.

The rk3328 got uart dmas fixed - a non-critical fix, as nobody was using
that so far.

New boards are the rk3328-based roc-rk3328-cc, the rk3368-based Lion-SOM
+ baseborad from Theobroma Systems and a standalone variant of the Sapphire
board, as a lot of people where using that without the Exkavator baseboard.

Sapphire also saw a lot of small cleanups of things that are not part
of the actual Sapphire board, but the baseboard instead. The rk3399-puma
board got i2s and tsadc support and Gru got its DP node enabled.

* tag 'v4.17-rockchip-dts64-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  arm64: dts: rockchip: remove keep-power-in-suspend from sdhci of rk3399-sapphire
  arm64: dts: rockchip: assign clock rate for ACLK_VIO on rk3399
  arm64: dts: rockchip: add a standalone version of the rk3399 sapphire
  arm64: dts: rockchip: move rk3399-sapphire pwr_btn to daughterboard
  arm64: dts: rockchip: move rk3399-sapphire i2s2 to daughterboard
  arm64: dts: rockchip: move rk3399-sapphire sdio to excavator baseboard
  arm64: dts: rockchip: enable I2S codec on rk3399-puma-haikou
  arm64: dts: rockchip: move i2s0 node from baseboard to SoM on rk3399-puma
  arm64: dts: rockchip: vdd_log on rk3399-sapphire is not an i2c slave
  arm64: dts: rockchip: add Haikou baseboard with RK3368-uQ7 SoM
  arm64: dts: rockchip: add RK3368-uQ7 (Lion) SoM
  dt-bindings: add RK3368-uQ7 SoM and EVK base board
  arm64: dts: rockchip: Fix RK3328 UART DMAs
  arm64: dts: rockchip: enable DP for rk3399-gru
  arm64: dts: rockchip: add cdn-dp node for rk3399.
  arm64: dts: rockchip: add i2s0-2ch-bus pins on rk3399
  arm64: dts: rockchip: enable tsadc on rk3399-puma
  arm64: dts: rockchip: add roc-rk3328-cc board
  arm64: dts: rockchip: Add cif test clocks for rk3399

Documentation/devicetree/bindings/arm/rockchip.txt

@@ -50,6 +50,10 @@ Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "firefly,firefly-rk3399", "rockchip,rk3399";
 
+- Firefly roc-rk3328-cc board:
+    Required root node properties:
+      - compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328";
+
 - ChipSPARK PopMetal-RK3288 board:
     Required root node properties:
       - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
@@ -181,10 +185,18 @@ Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
 
+- Rockchip RK3399 Sapphire board standalone:
+    Required root node properties:
+      - compatible = "rockchip,rk3399-sapphire", "rockchip,rk3399";
+
 - Rockchip RK3399 Sapphire Excavator board:
     Required root node properties:
       - compatible = "rockchip,rk3399-sapphire-excavator", "rockchip,rk3399";
 
+- Theobroma Systems RK3368-uQ7 Haikou Baseboard:
+    Required root node properties:
+      - compatible = "tsd,rk3368-uq7-haikou", "rockchip,rk3368";
+
 - Theobroma Systems RK3399-Q7 Haikou Baseboard:
     Required root node properties:
       - compatible = "tsd,rk3399-q7-haikou", "rockchip,rk3399";

arch/arm64/boot/dts/rockchip/Makefile

 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-lion-haikou.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
@@ -10,4 +12,5 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-kevin.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb

arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
+ */
+
+/dts-v1/;
+#include "rk3328.dtsi"
+
+/ {
+	model = "Firefly roc-rk3328-cc";
+	compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328";
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac_clkin: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac_clkin";
+		#clock-cells = <0>;
+	};
+
+	dc_12v: dc-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_12v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc0m1_gpio>;
+		regulator-name = "vcc_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb20_host_drv>;
+		regulator-name = "vcc_host1_5v";
+		regulator-always-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_sys: vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc_phy: vcc-phy-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_phy";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+	status = "okay";
+};
+
+&gmac2io {
+	assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+	assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_phy>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmiim1_pins>;
+	snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	tx_delay = <0x25>;
+	rx_delay = <0x11>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	rk805: pmic@18 {
+		compatible = "rockchip,rk805";
+		reg = <0x18>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk805-clkout2";
+		gpio-controller;
+		#gpio-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_io>;
+		vcc6-supply = <&vcc_io>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-min-microvolt = <712500>;
+				regulator-max-microvolt = <1450000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vdd_arm: DCDC_REG2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <712500>;
+				regulator-max-microvolt = <1450000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <950000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-name = "vcc_io";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_18: LDO_REG1 {
+				regulator-name = "vcc_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_emmc: LDO_REG2 {
+				regulator-name = "vcc18_emmc";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-name = "vdd_10";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb2 {
+		usb20_host_drv: usb20-host-drv {
+			rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
+	vmmc-supply = <&vcc_sd>;
+	status = "okay";
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&u2phy {
+	status = "okay";
+};
+
+&u2phy_host {
+	status = "okay";
+};
+
+&u2phy_otg {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb20_otg {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};

arch/arm64/boot/dts/rockchip/rk3328.dtsi

@@ -318,7 +318,7 @@ uart0: serial@ff110000 {
 		clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
 		clock-names = "baudclk", "apb_pclk";
 		dmas = <&dmac 2>, <&dmac 3>;
-		#dma-cells = <2>;
+		dma-names = "tx", "rx";
 		pinctrl-names = "default";
 		pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
 		reg-io-width = <4>;
@@ -333,7 +333,7 @@ uart1: serial@ff120000 {
 		clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
 		clock-names = "sclk_uart", "pclk_uart";
 		dmas = <&dmac 4>, <&dmac 5>;
-		#dma-cells = <2>;
+		dma-names = "tx", "rx";
 		pinctrl-names = "default";
 		pinctrl-0 = <&uart1_xfer &uart1_cts &uart1_rts>;
 		reg-io-width = <4>;
@@ -348,7 +348,7 @@ uart2: serial@ff130000 {
 		clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
 		clock-names = "baudclk", "apb_pclk";
 		dmas = <&dmac 6>, <&dmac 7>;
-		#dma-cells = <2>;
+		dma-names = "tx", "rx";
 		pinctrl-names = "default";
 		pinctrl-0 = <&uart2m1_xfer>;
 		reg-io-width = <4>;

arch/arm64/boot/dts/rockchip/rk3368-lion-haikou.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Theobroma Systems Design und Consulting GmbH
+ */
+
+/dts-v1/;
+#include "rk3368-lion.dtsi"
+
+/ {
+	model = "Theobroma Systems RK3368-uQ7 Baseboard";
+	compatible = "tsd,rk3368-lion-haikou", "rockchip,rk3368";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	i2cmux2 {
+		i2c@0 {
+			eeprom: eeprom@50 {
+				compatible = "atmel,24c01";
+				pagesize = <8>;
+				reg = <0x50>;
+			};
+		};
+	};
+
+	leds {
+		pinctrl-0 = <&led_pins_module>, <&led_sd_haikou>;
+
+		sd-card-led {
+			label = "sd_card_led";
+			gpios = <&gpio0 RK_PD2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+	};
+
+	dc_12v: dc-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_12v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	vcc3v3_baseboard: vcc3v3-baseboard {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_baseboard";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_otg: vcc5v0-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&otg_vbus_drv>;
+		regulator-name = "vcc5v0_otg";
+		regulator-always-on;
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio2 RK_PB3 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <25000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
+	rockchip,default-sample-phase = <90>;
+	vmmc-supply = <&vcc3v3_baseboard>;
+	status = "okay";
+};
+
+&spi2 {
+	cs-gpios = <0>, <&gpio2 RK_PC3 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+	status = "okay";
+};
+
+&uart1 {
+	/* alternate function of GPIO5/6 */
+	status = "disabled";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&haikou_pin_hog>;
+
+	hog {
+		haikou_pin_hog: haikou-pin-hog {
+			rockchip,pins =
+				/* LID_BTN */
+				<RK_GPIO3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
+				/* BATLOW# */
+				<RK_GPIO0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>,
+				/* SLP_BTN# */
+				<RK_GPIO3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
+				/* BIOS_DISABLE# */
+				<RK_GPIO3 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	leds {
+		led_sd_haikou: led-sd-gpio {
+			rockchip,pins =
+				<RK_GPIO0 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_cd_gpio: sdmmc-cd-gpio {
+			rockchip,pins =
+				<RK_GPIO2 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb_otg {
+		otg_vbus_drv: otg-vbus-drv {
+			rockchip,pins =
+				<RK_GPIO0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};

arch/arm64/boot/dts/rockchip/rk3368-lion.dtsi

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Theobroma Systems Design und Consulting GmbH
+ */
+
+/dts-v1/;
+#include "rk3368.dtsi"
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ext_gmac: gmac-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+		#clock-cells = <0>;
+	};
+
+	i2cmux1 {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c1>;
+		mux-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
+
+		/* Q7_GPO_I2C */
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		/* Q7_SMB */
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2cmux2 {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c2>;
+		mux-gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_HIGH>;
+
+		/* Q7_LVDS_BLC_I2C */
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fan: fan@18 {
+				compatible = "ti,amc6821";
+				reg = <0x18>;
+				cooling-min-state = <0>;
+				cooling-max-state = <9>;
+				#cooling-cells = <2>;
+			};
+
+			rtc_twi: rtc@6f {
+				compatible = "isil,isl1208";
+				reg = <0x6f>;
+			};
+		};
+
+		/* Q7_GP2_I2C */
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_module>;
+
+		module_led1 {
+			label = "module_led1";
+			gpios = <&gpio2 RK_PB5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			panic-indicator;
+		};
+
+		module_led2 {
+			label = "module_led2";
+			gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	vcc_sys: vcc-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_b2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_b3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	bus-width = <8>;
+	clock-frequency = <150000000>;
+	disable-wp;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&vcc33_io>;
+	vqmmc-supply = <&vcc18_io>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_bus8>;
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	clock_in_out = "input";
+	phy-supply = <&vcc33_io>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	snps,reset-gpio = <&gpio3 RK_PB3 GPIO_ACTIVE_HIGH>;
+	tx_delay = <0x10>;
+	rx_delay = <0x10>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA5 IRQ_TYPE_LEVEL_LOW>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+		#clock-cells = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>, <&pmic_sleep>;
+		rockchip,system-power-controller;
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_sys>;
+		vcc9-supply = <&vcc_sys>;
+		vcc10-supply = <&vcc_sys>;
+		vcc11-supply = <&vcc_sys>;
+		vcc12-supply = <&vcc_sys>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-name = "vdd_cpu";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd_log: DCDC_REG2 {
+				regulator-name = "vdd_log";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vcc33_io: DCDC_REG4 {
+				regulator-name = "vcc33_io";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vcc33_video: LDO_REG2 {
+				regulator-name = "vcc33_video";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vdd10_pll: LDO_REG3 {
+				regulator-name = "vdd10_pll";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vcc18_io: LDO_REG4 {
+				regulator-name = "vcc18_io";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+			};
+
+			vdd10_video: LDO_REG6 {
+				regulator-name = "vdd10_video";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vcc18_video: LDO_REG8 {
+				regulator-name = "vcc18_video";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&pinctrl {
+	leds {
+		led_pins_module: led-module-gpio {
+			rockchip,pins =
+				<RK_GPIO2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>,
+				<RK_GPIO3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <RK_GPIO0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		pmic_sleep: pmic-sleep {
+			rockchip,pins = <RK_GPIO0 RK_PA0 RK_FUNC_2 &pcfg_pull_none>;
+		};
+	};
+};
+
+&spi1 {
+	status = "okay";
+
+	norflash: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};

arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi

@@ -515,10 +515,15 @@ sound {
 		compatible = "rockchip,rk3399-gru-sound";
 		rockchip,cpu = <&i2s0 &i2s2>;
 		rockchip,codec = <&max98357a &headsetcodec
-				  &codec &wacky_spi_audio>;
+				  &codec &wacky_spi_audio &cdn_dp>;
 	};
 };
 
+&cdn_dp {
+	status = "okay";
+	extcon = <&usbc_extcon0>, <&usbc_extcon1>;
+};
+
 /*
  * Set some suspend operating points to avoid OVP in suspend
  *
@@ -581,7 +586,8 @@ &cru {
 		<&cru PCLK_PERIHP>,
 		<&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
 		<&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
-		<&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>;
+		<&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>,
+		<&cru ACLK_VIO>;
 	assigned-clock-rates =
 		<600000000>, <800000000>,
 		<1000000000>,
@@ -589,7 +595,8 @@ &cru {
 		<37500000>,
 		<100000000>, <100000000>,
 		<50000000>, <800000000>,
-		<100000000>, <50000000>;
+		<100000000>, <50000000>,
+		<400000000>;
 };
 
 &emmc_phy {

arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts

@@ -61,6 +61,30 @@ sd-card-led {
 		};
 	};
 
+	i2s0-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Haikou,I2S-codec";
+		simple-audio-card,mclk-fs = <512>;
+
+		simple-audio-card,codec {
+			clocks = <&sgtl5000_clk>;
+			sound-dai = <&sgtl5000>;
+		};
+
+		simple-audio-card,cpu {
+			bitclock-master;
+			frame-master;
+			sound-dai = <&i2s0>;
+		};
+	};
+
+	sgtl5000_clk: sgtl5000-oscillator  {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency  = <24576000>;
+	};
+
 	dc_12v: dc-12v {
 		compatible = "regulator-fixed";
 		regulator-name = "dc_12v";
@@ -80,6 +104,16 @@ vcc3v3_baseboard: vcc3v3-baseboard {
 		vin-supply = <&dc_12v>;
 	};
 
+	vcc5v0_baseboard: vcc5v0-baseboard {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_baseboard";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
 	vcc5v0_otg: vcc5v0-otg-regulator {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -89,6 +123,24 @@ vcc5v0_otg: vcc5v0-otg-regulator {
 		regulator-name = "vcc5v0_otg";
 		regulator-always-on;
 	};
+
+	vdda_codec: vdda-codec {
+		compatible = "regulator-fixed";
+		regulator-name = "vdda_codec";
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_baseboard>;
+	};
+
+	vddd_codec: vddd-codec {
+		compatible = "regulator-fixed";
+		regulator-name = "vddd_codec";
+		regulator-boot-on;
+		regulator-min-microvolt = <1600000>;
+		regulator-max-microvolt = <1600000>;
+		vin-supply = <&vcc5v0_baseboard>;
+	};
 };
 
 &i2c1 {
@@ -110,6 +162,17 @@ &i2c3 {
 &i2c4 {
 	status = "okay";
 	clock-frequency = <400000>;
+
+	sgtl5000: codec@0a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		clocks = <&sgtl5000_clk>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&vdda_codec>;
+		VDDIO-supply = <&vdda_codec>;
+		VDDD-supply = <&vddd_codec>;
+		status = "okay";
+	};
 };
 
 &i2c6 {
@@ -117,14 +180,6 @@ &i2c6 {
 	clock-frequency = <400000>;
 };
 
-&i2s0 {
-	status = "okay";
-	rockchip,playback-channels = <8>;
-	rockchip,capture-channels = <8>;
-	#sound-dai-cells = <0>;
-	status = "okay";
-};
-
 &pcie_phy {
 	status = "okay";
 };

arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi

@@ -435,6 +435,28 @@ vdd_cpu_b: regulator@60 {
 	};
 };
 
+&i2s0 {
+	pinctrl-0 = <&i2s0_2ch_bus>;
+	rockchip,playback-channels = <2>;
+	rockchip,capture-channels = <2>;
+	#sound-dai-cells = <0>;
+	status = "okay";
+};
+
+/*
+ * As Q7 does not specify neither a global nor a RX clock for I2S these
+ * signals are not used. Furthermore I2S0_LRCK_RX is used as GPIO.
+ * Therefore we have to redefine the i2s0_2ch_bus definition to prevent
+ * conflicts.
+ */
+&i2s0_2ch_bus {
+	rockchip,pins =
+		<RK_GPIO3 RK_PD0 RK_FUNC_1 &pcfg_pull_none>,
+		<RK_GPIO3 RK_PD2 RK_FUNC_1 &pcfg_pull_none>,
+		<RK_GPIO3 RK_PD3 RK_FUNC_1 &pcfg_pull_none>,
+		<RK_GPIO3 RK_PD7 RK_FUNC_1 &pcfg_pull_none>;
+};
+
 &io_domains {
 	status = "okay";
 	bt656-supply = <&vcc_1v8>;
@@ -505,6 +527,12 @@ norflash: flash@0 {
 	};
 };
 
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <1>;
+	status = "okay";
+};
+
 &u2phy1 {
 	status = "okay";
 

arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts

@@ -41,7 +41,6 @@
  */
 
 /dts-v1/;
-#include <dt-bindings/input/input.h>
 #include "rk3399-sapphire.dtsi"
 
 / {
@@ -95,22 +94,6 @@ panel_in_edp: endpoint {
 		};
 	};
 
-	keys: gpio-keys {
-		compatible = "gpio-keys";
-		autorepeat;
-
-		power {
-			debounce-interval = <100>;
-			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
-			label = "GPIO Power";
-			linux,code = <KEY_POWER>;
-			linux,input-type = <1>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pwr_btn>;
-			wakeup-source;
-		};
-	};
-
 	rt5651-sound {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "realtek,rt5651-codec";
@@ -207,18 +190,7 @@ &i2s0 {
 	status = "okay";
 };
 
-&i2s2 {
-	#sound-dai-cells = <0>;
-	status = "okay";
-};
-
 &pinctrl {
-	buttons {
-		pwr_btn: pwr-btn {
-			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
-		};
-	};
-
 	sdio-pwrseq {
 		wifi_enable_h: wifi-enable-h {
 			rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
@@ -232,6 +204,22 @@ lcd_panel_reset: lcd-panel-reset {
 	};
 };
 
+&sdio0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	clock-frequency = <50000000>;
+	disable-wp;
+	keep-power-in-suspend;
+	max-frequency = <50000000>;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
 &spdif {
 	i2c-scl-rising-time-ns = <450>;
 	i2c-scl-falling-time-ns = <15>;

arch/arm64/boot/dts/rockchip/rk3399-sapphire.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Fuzhou Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+#include "rk3399-sapphire.dtsi"
+
+/ {
+	model = "Sapphire-RK3399 Board";
+	compatible = "rockchip,rk3399-sapphire", "rockchip,rk3399";
+};

arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi

@@ -41,6 +41,7 @@
  */
 
 #include "dt-bindings/pwm/pwm.h"
+#include "dt-bindings/input/input.h"
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
 
@@ -102,6 +103,22 @@ dc_12v: dc-12v {
 		regulator-max-microvolt = <12000000>;
 	};
 
+	keys: gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		power {
+			debounce-interval = <100>;
+			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+			label = "GPIO Power";
+			linux,code = <KEY_POWER>;
+			linux,input-type = <1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwr_btn>;
+			wakeup-source;
+		};
+	};
+
 	/* switched by pmic_sleep */
 	vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
 		compatible = "regulator-fixed";
@@ -143,6 +160,17 @@ vcc5v0_host: vcc5v0-host-regulator {
 		regulator-always-on;
 		vin-supply = <&vcc_sys>;
 	};
+
+	vdd_log: vdd-log {
+		compatible = "pwm-regulator";
+		pwms = <&pwm2 0 25000 1>;
+		regulator-name = "vdd_log";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1400000>;
+		vin-supply = <&vcc_sys>;
+	};
 };
 
 &cpu_l0 {
@@ -421,17 +449,6 @@ regulator-state-mem {
 			regulator-off-in-suspend;
 		};
 	};
-
-	vdd_log: vdd-log {
-		compatible = "pwm-regulator";
-		pwms = <&pwm2 0 25000 1>;
-		regulator-name = "vdd_log";
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <800000>;
-		regulator-max-microvolt = <1400000>;
-		vin-supply = <&vcc_sys>;
-	};
 };
 
 &i2c3 {
@@ -440,6 +457,11 @@ &i2c3 {
 	status = "okay";
 };
 
+&i2s2 {
+	#sound-dai-cells = <0>;
+	status = "okay";
+};
+
 &io_domains {
 	status = "okay";
 
@@ -470,6 +492,12 @@ &pmu_io_domains {
 };
 
 &pinctrl {
+	buttons {
+		pwr_btn: pwr-btn {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
 	pmic {
 		pmic_int_l: pmic-int-l {
 			rockchip,pins =
@@ -513,29 +541,12 @@ &saradc {
 
 &sdhci {
 	bus-width = <8>;
-	keep-power-in-suspend;
 	mmc-hs400-1_8v;
 	mmc-hs400-enhanced-strobe;
 	non-removable;
 	status = "okay";
 };
 
-&sdio0 {
-	bus-width = <4>;
-	cap-sd-highspeed;
-	cap-sdio-irq;
-	clock-frequency = <50000000>;
-	disable-wp;
-	keep-power-in-suspend;
-	max-frequency = <50000000>;
-	mmc-pwrseq = <&sdio_pwrseq>;
-	non-removable;
-	pinctrl-names = "default";
-	pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
-	sd-uhs-sdr104;
-	status = "okay";
-};
-
 &sdmmc {
 	bus-width = <4>;
 	cap-mmc-highspeed;

arch/arm64/boot/dts/rockchip/rk3399.dtsi

@@ -457,6 +457,42 @@ usbdrd_dwc3_1: dwc3 {
 		};
 	};
 
+	cdn_dp: dp@fec00000 {
+		compatible = "rockchip,rk3399-cdn-dp";
+		reg = <0x0 0xfec00000 0x0 0x100000>;
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
+		assigned-clocks = <&cru SCLK_DP_CORE>;
+		assigned-clock-rates = <100000000>;
+		clocks = <&cru SCLK_DP_CORE>, <&cru PCLK_DP_CTRL>,
+			 <&cru SCLK_SPDIF_REC_DPTX>, <&cru PCLK_VIO_GRF>;
+		clock-names = "core-clk", "pclk", "spdif", "grf";
+		phys = <&tcphy0_dp>, <&tcphy1_dp>;
+		power-domains = <&power RK3399_PD_HDCP>;
+		resets = <&cru SRST_DPTX_SPDIF_REC>, <&cru SRST_P_UPHY0_DPTX>,
+			 <&cru SRST_P_UPHY0_APB>, <&cru SRST_DP_CORE>;
+		reset-names = "spdif", "dptx", "apb", "core";
+		rockchip,grf = <&grf>;
+		#sound-dai-cells = <1>;
+		status = "disabled";
+
+		ports {
+			dp_in: port {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				dp_in_vopb: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&vopb_out_dp>;
+				};
+
+				dp_in_vopl: endpoint@1 {
+					reg = <1>;
+					remote-endpoint = <&vopl_out_dp>;
+				};
+			};
+		};
+	};
+
 	gic: interrupt-controller@fee00000 {
 		compatible = "arm,gic-v3";
 		#interrupt-cells = <4>;
@@ -1286,7 +1322,8 @@ cru: clock-controller@ff760000 {
 			<&cru PCLK_PERIHP>,
 			<&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
 			<&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
-			<&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>;
+			<&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>,
+			<&cru ACLK_VIO>;
 		assigned-clock-rates =
 			 <594000000>,  <800000000>,
 			<1000000000>,
@@ -1294,7 +1331,8 @@ cru: clock-controller@ff760000 {
 			  <37500000>,
 			 <100000000>,  <100000000>,
 			  <50000000>, <600000000>,
-			 <100000000>,   <50000000>;
+			 <100000000>,   <50000000>,
+			 <400000000>;
 	};
 
 	grf: syscon@ff770000 {
@@ -1547,6 +1585,11 @@ vopl_out_mipi1: endpoint@3 {
 				reg = <3>;
 				remote-endpoint = <&mipi1_in_vopl>;
 			};
+
+			vopl_out_dp: endpoint@4 {
+				reg = <4>;
+				remote-endpoint = <&dp_in_vopl>;
+			};
 		};
 	};
 
@@ -1599,6 +1642,11 @@ vopb_out_mipi1: endpoint@3 {
 				reg = <3>;
 				remote-endpoint = <&mipi1_in_vopb>;
 			};
+
+			vopb_out_dp: endpoint@4 {
+				reg = <4>;
+				remote-endpoint = <&dp_in_vopb>;
+			};
 		};
 	};
 
@@ -2043,6 +2091,16 @@ i2c8_xfer: i2c8-xfer {
 		};
 
 		i2s0 {
+			i2s0_2ch_bus: i2s0-2ch-bus {
+				rockchip,pins =
+					<3 24 RK_FUNC_1 &pcfg_pull_none>,
+					<3 25 RK_FUNC_1 &pcfg_pull_none>,
+					<3 26 RK_FUNC_1 &pcfg_pull_none>,
+					<3 27 RK_FUNC_1 &pcfg_pull_none>,
+					<3 31 RK_FUNC_1 &pcfg_pull_none>,
+					<4 0 RK_FUNC_1 &pcfg_pull_none>;
+			};
+
 			i2s0_8ch_bus: i2s0-8ch-bus {
 				rockchip,pins =
 					<3 24 RK_FUNC_1 &pcfg_pull_none>,
@@ -2293,6 +2351,23 @@ spi5_tx: spi5-tx {
 			};
 		};
 
+		testclk {
+			test_clkout0: test-clkout0 {
+				rockchip,pins =
+					<0 0 RK_FUNC_1 &pcfg_pull_none>;
+			};
+
+			test_clkout1: test-clkout1 {
+				rockchip,pins =
+					<2 25 RK_FUNC_2 &pcfg_pull_none>;
+			};
+
+			test_clkout2: test-clkout2 {
+				rockchip,pins =
+					<0 8 RK_FUNC_3 &pcfg_pull_none>;
+			};
+		};
+
 		tsadc {
 			otp_gpio: otp-gpio {
 				rockchip,pins = <1 6 RK_FUNC_GPIO &pcfg_pull_none>;