fsl,usbphy is no optional property. This patch moves it to the list of
required properties.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

-ENODEV is interpreted by the generic driver probing function as a
non-matching driver. This leads to a missing probe failure message.

Also a missing USB PHY is more of an invalid configuration of the usb
driver because it is necessary.

This patch returns -EINVAL if devm_usb_get_phy_by_phandle() returned -ENODEV.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Section 4.4.7.2 "Interrupt Transfer Bandwidth Requirements" of the USB3.0 spec
says:
	A zero-length data payload is a valid transfer and may be useful for
	some implementations.

So, extend the logic of allowing URB_ZERO_PACKET to interrupt urbs too.
Otherwise, the kernel throws warning of BOGUS transfer flags.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Following sparse warnings were reported by kbuild test bot

drivers/usb/misc/lvstest.c:314:28: sparse: incorrect type in assignment (different base types)
   drivers/usb/misc/lvstest.c:314:28:    expected unsigned short [unsigned] [usertype] portchange
   drivers/usb/misc/lvstest.c:314:28:    got restricted __le16 [usertype] wPortChange
drivers/usb/misc/lvstest.c:332:40: sparse: restricted __le16 degrades to integer

This patch fixes above warnings.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The assigned IRQ should be freed before calling pci_disable_device()
when shutting down system, otherwise it will cause following warning.
[  568.879482] ------------[ cut here ]------------
[  568.884236] WARNING: CPU: 1 PID: 3300 at /home/konrad/ssd/konrad/xtt-i386/bootstrap/linux-usb/fs/proc/generic.c:521 remove_proc_entry+0x165/0x170()
[  568.897846] remove_proc_entry: removing non-empty directory 'irq/16', leaking at least 'ohci_hcd:usb4'
[  568.907430] Modules linked in: dm_multipath dm_mod iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi libcrc32c crc32c_generic sg sd_mod crct10dif_generic crc_t10dif crct10dif_common radeon fbcon tileblit ttm font bitblit softcursor ata_generic ahci libahci drm_kms_helper skge r8169 libata mii scsi_mod wmi acpi_cpufreq
[  568.938539] CPU: 1 PID: 3300 Comm: init Tainted: G        W     3.16.0-rc5upstream-01651-g03b9189 #1
[  568.947946] Hardware name: ECS A780GM-A Ultra/A780GM-A Ultra, BIOS 080015  04/01/2010
[  568.956008]  00000209 ed0f1cd0 c1617946 c175403c ed0f1d00 c1090c3f c1754084 ed0f1d2c
[  568.964068]  00000ce4 c175403c 00000209 c11f22a5 c11f22a5 f755e8c0 ed0f1d78 f755e90d
[  568.972128]  ed0f1d18 c1090cde 00000009 ed0f1d10 c1754084 ed0f1d2c ed0f1d60 c11f22a5
[  568.980194] Call Trace:
[  568.982715]  [<c1617946>] dump_stack+0x48/0x60
[  568.987294]  [<c1090c3f>] warn_slowpath_common+0x7f/0xa0
[  569.003887]  [<c1090cde>] warn_slowpath_fmt+0x2e/0x30
[  569.009092]  [<c11f22a5>] remove_proc_entry+0x165/0x170
[  569.014476]  [<c10da6ca>] unregister_irq_proc+0xaa/0xc0
[  569.019858]  [<c10d582f>] free_desc+0x1f/0x60
[  569.024346]  [<c10d58aa>] irq_free_descs+0x3a/0x80
[  569.029283]  [<c10d9e9d>] irq_dispose_mapping+0x2d/0x50
[  569.034666]  [<c1078fd3>] mp_unmap_irq+0x73/0xa0
[  569.039423]  [<c107196b>] acpi_unregister_gsi_ioapic+0x2b/0x40
[  569.045431]  [<c107180f>] acpi_unregister_gsi+0xf/0x20
[  569.050725]  [<c1339cad>] acpi_pci_irq_disable+0x4b/0x50
[  569.056196]  [<c14daa38>] pcibios_disable_device+0x18/0x20
[  569.061848]  [<c130123d>] do_pci_disable_device+0x4d/0x60
[  569.067410]  [<c13012b7>] pci_disable_device+0x47/0xb0
[  569.077814]  [<c14800b1>] usb_hcd_pci_shutdown+0x31/0x40
[  569.083285]  [<c1304b19>] pci_device_shutdown+0x19/0x50
[  569.088667]  [<c13fda64>] device_shutdown+0x14/0x120
[  569.093777]  [<c10ac29d>] kernel_restart_prepare+0x2d/0x30
[  569.099429]  [<c10ac41e>] kernel_restart+0xe/0x60
[  569.109028]  [<c10ac611>] SYSC_reboot+0x191/0x220
[  569.159269]  [<c10ac6ba>] SyS_reboot+0x1a/0x20
[  569.163843]  [<c161c718>] sysenter_do_call+0x12/0x16
[  569.168951] ---[ end trace ccc1ec4471c289c9 ]---
Tested-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Felipe writes:

usb: patches for v3.17 merge window

Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).

The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>

This patch adds an extra check to ohci-hcd's I/O watchdog routine.  If
the controller stops updating the frame counter, we will assume it is
dead.  But there has to be an exception: Some controllers stop the
frame counter when no ports are connected.  Check to make sure there
is at least one active port before deciding the controller is dead.

(This test may appear racy, but it isn't.  Enabling a newly connected
port takes several milliseconds, during which time the frame counter
must advance.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dennis New <dennisn@dennisn.linuxd.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some OHCI controllers have a bug: They fail to add completed TDs to
the done queue.  Examining this queue is the only method ohci-hcd has
for telling when a transfer is complete; failure to add a TD can
result in an URB that never completes and cannot be unlinked.

This patch adds a watchdog routine to ohci-hcd.  The routine
periodically scans the active ED and TD lists, looking for TDs which
are finished but not on the done queue.  When one is found, and it is
certain that the controller hardware will never add the TD to the done
queue, the watchdog routine manually puts the TD on the done list so
that it can be handled normally.

The watchdog routine also checks for a condition indicating the
controller has died.  If the done queue is non-empty but the
HccaDoneHead pointer hasn't been updated for a few hundred
milliseconds, we assume the controller will never update it and
therefore is dead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

URBs for a particular endpoint should complete sequentially.  That is,
we shouldn't call the completion handler for one URB until the handler
for the previous URB has returned.

When the OHCI watchdog routine is added, there will be two paths for
completing URBs: interrupt handler and watchdog routine.  Their
activities have to be synchronized so that completions don't occur in
multiple threads concurrently.

For that purpose, this patch creates an ohci_work() routine which will
be responsible for calling process_done_list() and finish_unlinks(),
the two routines that detect when an URB is complete.  Everything will
funnel through ohci_work(), and it will be careful not to run in more
than one thread at a time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch changes the way ohci-hcd handles the TD done list.  In
addition to relying on the TD pointers stored by the controller
hardware, we need to handle TDs that the hardware has forgotten about.

This means the list has to exist even while the dl_done_list() routine
isn't running.  That function essentially gets split in two:
update_done_list() reads the TD pointers stored by the hardware and
adds the TDs to the done list, and process_done_list() scans through
the list to handle URB completions.  When we detect a TD that the
hardware forgot about, we will be able to add it to the done list
manually and then process it normally.

Since the list is really a queue, and because there can be a lot of
TDs, keep the existing singly linked implementation.  To insure that
URBs are given back in order of submission, whenever a TD is added to
the done list, all the preceding TDs for the same endpoint must be
added as well (going back to the first one that isn't already on the
done list).

The done list manipulations must all be protected by the private
lock.  The scope of the lock is expanded in preparation for the
watchdog routine to be added in a later patch.

We have to be more careful about giving back unlinked URBs.  Since TDs
may be added to the done list by the watchdog routine and not in
response to a controller interrupt, we have to check explicitly to
make sure all the URB's TDs that were added to the done list have been
processed before giving back the URB.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When an URB is unlinked from a dead controller, ohci-hcd gives back
the URB with no regard for cleaning up the internal data structures.
This won't play nicely with the upcoming changes to the TD done
list.

Therefore make ohci_urb_dequeue() call finish_unlinks(), which uses
td_done() to do a proper cleanup, rather than calling finish_urb()
directly.  Also, remove the checks that urb_priv is non-NULL; the
driver guarantees that urb_priv will never be NULL for a valid URB.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch reverts the important parts of commit 89a0fd18 (USB:
OHCI handles more ZFMicro quirks), namely, the parts related to
handling orphan TDs for interrupt endpoints.  A later patch in this
series will introduce a more general mechanism that applies to all
endpoint types and all controllers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Problem Summary: Problem has been observed generally with PM states
where VBUS goes off during suspend. There are some SS USB devices which
take longer time for link training compared to many others.  Such
devices fail to reconnect with same old address which was associated
with it before suspend.

When system resumes, at some point of time (dpm_run_callback->
usb_dev_resume->usb_resume->usb_resume_both->usb_resume_device->
usb_port_resume) SW reads hub status. If device is present,
then it finishes port resume and re-enumerates device with same
address. If device is not present then, SW thinks that device was
removed during suspend and therefore does logical disconnection
and removes all the resource allocated for this device.

Now, if I put sufficient delay just before root hub status read in
usb_resume_device then, SW sees always that device is present. In normal
course(without any delay) SW sees that no device is present and then SW
removes all resource associated with the device at this port.  In the
latter case, after sometime, device says that hey I am here, now host
enumerates it, but with new address.

Problem had been reproduced when I connect verbatim USB3.0 hard disc
with my STiH407 XHCI host running with 3.10 kernel.

I see that similar problem has been reported here.
https://bugzilla.kernel.org/show_bug.cgi?id=53211
Reading above it seems that bug was not in 3.6.6 and was present in 3.8
and again it was not present for some in 3.12.6, while it was present
for few others. I tested with 3.13-FC19 running at i686 desktop, problem
was still there. However, I was failed to reproduce it with 3.16-RC4
running at same i686 machine. I would say it is just a random
observation. Problem for few devices is always there, as I am unable to
find a proper fix for the issue.

So, now question is what should be the amount of delay so that host is
always able to recognize suspended device after resume.

XHCI specs 4.19.4 says that when Link training is successful, port sets
CSC bit to 1. So if SW reads port status before successful link
training, then it will not find device to be present.  USB Analyzer log
with such buggy devices show that in some cases device switch on the
RX termination after long delay of host enabling the VBUS. In few other
cases it has been seen that device fails to negotiate link training in
first attempt. It has been reported till now that few devices take as
long as 2000 ms to train the link after host enabling its VBUS and
RX termination. This patch implements a 2000 ms timeout for CSC bit to set
ie for link training. If in a case link trains before timeout, loop will
exit earlier.

This patch implements above delay, but only for SS device and when
persist is enabled.

So, for the good device overhead is almost none. While for the bad
devices penalty could be the time which it take for link training.
But, If a device was connected before suspend, and was removed
while system was asleep, then the penalty would be the timeout ie
2000 ms.

Results:

Verbatim USB SS hard disk connected with STiH407 USB host running 3.10
Kernel resumes in 461 msecs without this patch, but hard disk is
assigned a new device address. Same system resumes in 790 msecs with
this patch, but with old device address.

Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I am removing two fix mes in this file as after dicussing then it  seems
there is no reason to check against Null for usb_device as it can never
be NULL and this is check is therefore not needed.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some laptops have an internal port for a BT device which picks
up noise when the kill switch is used, but not enough to trigger
printk_rlimit(). So we shouldn't log consecutive faults of this kind.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This `usb_reset_device` command has been around since the driver was
originally reverse engineered. It doesn't cause much issue on single
interface CP210x devices, but on the CP2105 and CP2108 with 2 and 4
interfaces respectively it will cause instability on enumeration and
delays enumeration noticably. There should be no reason to reset a device
at startup, per the CP210x AN571 spec.
Signed-off-by: Preston Fick <preston.fick@silabs.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

OTG3 and EH Compliance Plan 1.0 talks about Super Speed OTG Verification
system (SS-OVS) which consists of an excersizer and analyzer.

USB Compliance Suite from Lecroy or Ellisys can act as such SS-OVS for
Link Layer Validation (LVS).

Some modifications are needed for an embedded Linux USB host to pass all
these tests.  Most of these tests require just Link to be in U0. They do
not work with default Linux USB stack since, default stack does port
reset and then starts sending setup packet, which is not expected by
Link Layer Validation (LVS) device of Lecroy Compliance Suit.  Then,
There are many Link Layer Tests which need host to generate specific
traffic.

This patch supports specific traffic generation cases. As of now all the
host Lecroy Link Layer-USBIF tests (except TD7.26) passes
with this patch for single run using  Lecroy USB Compliance Suite
Version 1.98 Build 239 and Lecroy USB Protocol Analyzer version 4.80
Build 1603. Therefore patch seems to be a good candidate for inclusion.
Further modification can be done on top of it.

lvstest driver will not bind to any device by default. It can bind
manually to a super speed USB host controller root hub. Therefore, regular
hub driver must be unbound before this driver is bound. For example, if
2-0:1.0 is the xhci root hub, then execute following to unbind hub driver.

 echo 2-0:1.0 > /sys/bus/usb/drivers/hub/unbind

Then write Linux Foundation's vendor ID which is used by root hubs and
SS root hub's device ID into new_id file. Writing IDs into new_id file
will also bind the lvs driver with any available SS root hub interfaces.

 echo "1D6B 3" > /sys/bus/usb/drivers/lvs/new_id

Now connect LVS device with root hub port.

Test case specific traffic can be generated as follows whenever needed:

1. To issue "Get Device descriptor" command for TD.7.06:
 echo  > /sys/bus/usb/devices/2-0\:1.0/get_dev_desc

2. To set U1 timeout to 127 for TD.7.18
 echo 127 > /sys/bus/usb/devices/2-0\:1.0/u1_timeout

3. To set U2 timeout to 0 for TD.7.18
 echo 0 > /sys/bus/usb/devices/2-0\:1.0/u2_timeout

4. To issue "Hot Reset" for TD.7.29
 echo  > /sys/bus/usb/devices/2-0\:1.0/hot_reset

5. To issue "U3 Entry" for TD.7.35
 echo  > /sys/bus/usb/devices/2-0\:1.0/u3_entry

6. To issue "U3 Exit" for TD.7.36
 echo  > /sys/bus/usb/devices/2-0\:1.0/u3_exit
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_alloc_dev is used by lvstest driver now which can be built as
module. Therefore export usb_alloc_dev symbol.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a bug in ohci-hcd.  When an URB is unlinked, the
corresponding Endpoint Descriptor is added to the ed_rm_list and taken
off the hardware schedule.  Once the ED is no longer visible to the
hardware, finish_unlinks() handles the URBs that were unlinked or have
completed.  If any URBs remain attached to the ED, the ED is added
back to the hardware schedule -- but only if the controller is
running.

This fails when a controller dies.  A non-empty ED does not get added
back to the hardware schedule and does not remain on the ed_rm_list;
ohci-hcd loses track of it.  The remaining URBs cannot be unlinked,
which causes the USB stack to hang.

The patch changes finish_unlinks() so that non-empty EDs remain on
the ed_rm_list if the controller isn't running.  This requires moving
some of the existing code around, to avoid modifying the ED's hardware
fields more than once.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The debug routine fill_async_buffer() in ohci-hcd is buggy: It never
produces any output because it forgets to initialize the output buffer
size.  Also, the debug routine ohci_dump() has an unused argument.

This patch adds the correct initialization and removes the unused
argument.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Apparently nobody ever remembered to add Scatter-Gather support to
ohci-hcd.  This patch adds it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When a host controller dies, we don't need to wait for a driver to
time out.  We can shut down its URBs immediately.  Without this
change, we can end up waiting 30 seconds for a mass-storage transfer
to time out.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Gadget function files have been moved to a "function" subdirectory.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

f->os_desc_table[0].if_id is zero by default. If the actual id happens
to be different then no Feature Descriptors will be returned to the host
for this interface, so assign if_id as soon as it is known.

Cc: <stable@vger.kernel.org> # v3.16
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The pcm playback and capture sample size format was fixed
SNDRV_PCM_FMTBIT_S16_LE.

This patch respects also 16, 24 and 32 bit p_ssize and c_ssize values.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sebastian Reimers <sebastian.reimers@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

No functional changes, just fixing one easy to spot
sparse error.

While fixing that sparse error, I had to add two
includes to a header to avoid a build error.
Signed-off-by: Felipe Balbi <balbi@ti.com>

No functional changes, just fixing one easy
to spot sparse error.
Signed-off-by: Felipe Balbi <balbi@ti.com>

No functional changes, just fixing some easy
to spot sparse errors.
Signed-off-by: Felipe Balbi <balbi@ti.com>

The drivers/usb/gadget directory contains many files.
Files which are related can be distributed into separate directories.
This patch moves the USB functions implementations into a separate directory.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The drivers/usb/gadget directory contains many files.
Files which are related can be distributed into separate directories.
This patch moves the UDC drivers into a separate directory.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The drivers/usb/gadget directory contains many files.
Files which are related can be distributed into separate directories.
This patch moves the legacy gadgets (i.e. those not using configfs)
into a separate directory.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Merge tag 'usb-serial-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

Johan writes:

USB-serial updates for v3.17-rc1

Here are some minor fixes and clean-ups to the ftdi_sio, mos7840 and kl5kusb105
drivers for v3.17-rc1.
Signed-off-by: Johan Hovold <johan@kernel.org>

In preparation for DT conversion to reduce reliance on platform device
callbacks.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch try to dequeue the cdev->req to guarantee the request is not queued
before free it.
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add sw_babble_control() logic to differentiate between transient
babble and real babble condition. Also add the SW babble control
register definitions.

Babble control register logic is implemented in the latest
revision of AM335x.

Find whether we are running on newer silicon. The babble control
register reads 0x4 by default in newer silicon as opposed to 0
in old versions of AM335x. Based on this enable the sw babble
control logic.
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Currently musb_platform_reset() is only used by dsps.
In case of BABBLE interrupt for other platforms the  musb_platform_reset()
is a NOP. In such situations no need to re-initialize the endpoints.
Also in the latest silicon revision of AM335x, we do have a babble recovery
mechanism without resetting the IP block. In preperation to add that support
its better to have a rest_done return for  musb_platform_reset().
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

During babble condition both first disconnect of devices are
initiated. Make sure MUSB controller is reset and re-initialized
after all disconnects.

To acheive this schedule a delayed work for babble recovery.

While at that convert udelay to usleep_range.
Refer Documentation/timers/timers-howto.txt
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

BABBLE and RESET share the same interrupt. The interrupt
is considered to be RESET if MUSB is in peripheral mode and
as a BABBLE if MUSB is in HOST mode.

Handle babble condition iff MUSB is in HOST mode.
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Move the extcon related code to its own function.
Improve code readability, decrease the dwc3_probe() size.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Move find and set the utmi mode to its own separate function.
Improve code readability, decrease the dwc3_probe() size.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>