- 08 Apr, 2017 40 commits
-
-
Peter Xu authored
commit df630b8c upstream. When releasing the bus, let's clear the bus pointers to mark it out. If any further device unregister happens on this bus, we know that we're done if we found the bus being released already. Signed-off-by:
Peter Xu <peterx@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Uwe Kleine-König authored
commit a6040bc6 upstream. The reference manual for the i.MX28 recommends to calculate the divisor as divisor = (UARTCLK * 32) / baud rate, rounded to the nearest integer , so let's do this. For a typical setup of UARTCLK = 24 MHz and baud rate = 115200 this changes the divisor from 6666 to 6667 and so the actual baud rate improves from 115211.521 Bd (error ≅ 0.01 %) to 115194.240 Bd (error ≅ 0.005 %). Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Alan Stern authored
commit 16336820 upstream. Using KASAN, Dmitry found a bug in the rh_call_control() routine: If buffer allocation fails, the routine returns immediately without unlinking its URB from the control endpoint, eventually leading to linked-list corruption. This patch fixes the problem by jumping to the end of the routine (where the URB is unlinked) when an allocation failure occurs. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Mathias Nyman authored
commit 0ab2881a upstream. A control transfer that stopped at the status stage incorrectly warned about a "unexpected TRB Type 4", and did not set the transferred actual_length for the URB. The URB actual_length for control transfers should contain the bytes transferred in the data stage. Bytes of a partially sent setup stage and missing bytes from status stage should be left out. Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Nicolas Ferre authored
commit 497e1e16 upstream. A side effect of 89d82324 ("tty/serial: atmel_serial: BUG: stop DMA from transmitting in stop_tx") is that the console can be called with TX path disabled. Then the system would hang trying to push charecters out in atmel_console_putchar(). Signed-off-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Fixes: 89d82324 ("tty/serial: atmel_serial: BUG: stop DMA from transmitting in stop_tx") Signed-off-by:
-
Richard Genoud authored
commit 31ca2c63 upstream. If uart_flush_buffer() is called between atmel_tx_dma() and atmel_complete_tx_dma(), the circular buffer has been cleared, but not atmel_port->tx_len. That leads to a circular buffer overflow (dumping (UART_XMIT_SIZE - atmel_port->tx_len) bytes). Tested-by:
Richard Genoud <richard.genoud@gmail.com> Signed-off-by:
-
Joerg Roedel authored
commit 08f63d97 upstream. No platform-device is required for IO(x)APICs, so don't even create them. [ rjw: This fixes a problem with leaking platform device objects after IOAPIC/IOxAPIC hot-removal events.] Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Josh Poimboeuf authored
commit 61b79e16 upstream. Paul Menzel reported a warning: WARNING: CPU: 0 PID: 774 at /build/linux-ROBWaj/linux-4.9.13/kernel/trace/trace_functions_graph.c:233 ftrace_return_to_handler+0x1aa/0x1e0 Bad frame pointer: expected f6919d98, received f6919db0 from func acpi_pm_device_sleep_wake return to c43b6f9d The warning means that function graph tracing is broken for the acpi_pm_device_sleep_wake() function. That's because the ACPI Makefile unconditionally sets the '-Os' gcc flag to optimize for size. That's an issue because mcount-based function graph tracing is incompatible with '-Os' on x86, thanks to the following gcc bug: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=42109 I have another patch pending which will ensure that mcount-based function graph tracing is never used with CONFIG_CC_OPTIMIZE_FOR_SIZE on x86. But this patch is needed in addition to that one because the ACPI Makefile overrides that config option for no apparent reason. It has had this flag since the beginning of git history, and there's no related comment, so I don't know why it's there. As far as I can tell, there's no reason for it to be there. The appropriate behavior is for it to honor CONFIG_CC_OPTIMIZE_FOR_{SIZE,PERFORMANCE} like the rest of the kernel. Reported-by:
Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Helge Deller authored
commit 554bfece upstream. pa_memcpy() is the major memcpy implementation in the parisc kernel which is used to do any kind of userspace/kernel memory copies. Al Viro noticed various bugs in the implementation of pa_mempcy(), most notably that in case of faults it may report back to have copied more bytes than it actually did. Fixing those bugs is quite hard in the C-implementation, because the compiler is messing around with the registers and we are not guaranteed that specific variables are always in the same processor registers. This makes proper fault handling complicated. This patch implements pa_memcpy() in assembler. That way we have correct fault handling and adding a 64-bit copy routine was quite easy. Runtime tested with 32- and 64bit kernels. Reported-by:
Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by:
John David Anglin <dave.anglin@bell.net> Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Helge Deller authored
commit 476e75a4 upstream. Commit 73580dac ("parisc: Fix system shutdown halt") introduced an endless loop for systems which don't provide a software power off function. But the soft lockup detector will detect this and report stalled CPUs after some time. Avoid those unwanted warnings by disabling the soft lockup detector. Fixes: 73580dac ("parisc: Fix system shutdown halt") Signed-off-by:
-
Helge Deller authored
commit d19f5e41 upstream. Al Viro noticed that userspace accesses via get_user()/put_user() can be simplified a lot with regard to usage of the exception handling. This patch implements a fixup routine for get_user() and put_user() in such that the exception handler will automatically load -EFAULT into the register %r8 (the error value) in case on a fault on userspace. Additionally the fixup routine will zero the target register on fault in case of a get_user() call. The target register is extracted out of the faulting assembly instruction. This patch brings a few benefits over the old implementation: 1. Exception handling gets much cleaner, easier and smaller in size. 2. Helper functions like fixup_get_user_skip_1 (all of fixup.S) can be dropped. 3. No need to hardcode %r9 as target register for get_user() any longer. This helps the compiler register allocator and thus creates less assembler statements. 4. No dependency on the exception_data contents any longer. 5. Nested faults will be handled cleanly. Reported-by:
-
Thomas Petazzoni authored
commit 74d1cf48 upstream. Commit 52060836 ("dt-bindings: omap-rng: Document SafeXcel IP-76 device variant") update the omap_rng Device Tree binding to add support for the IP-76 variation of the IP. As part of this change, a "clocks" property was added, but is indicated as "Required", without indicated it's actually only required for some compatible strings. This commit fixes that, by explicitly stating that the clocks property is only required with the inside-secure,safexcel-eip76 compatible string. Fixes: 52060836 ("dt-bindings: omap-rng: Document SafeXcel IP-76 device variant") Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Kinglong Mee authored
commit c952cd4e upstream. Now that Ext4 and f2fs filesystems support encrypted directories and files, attempts to access those files may return ENOKEY, resulting in the following WARNING. Map ENOKEY to nfserr_perm instead of nfserr_io. [ 1295.411759] ------------[ cut here ]------------ [ 1295.411787] WARNING: CPU: 0 PID: 12786 at fs/nfsd/nfsproc.c:796 nfserrno+0x74/0x80 [nfsd] [ 1295.411806] nfsd: non-standard errno: -126 [ 1295.411816] Modules linked in: nfsd nfs_acl auth_rpcgss nfsv4 nfs lockd fscache tun bridge stp llc fuse ip_set nfnetlink vmw_vsock_vmci_transport vsock snd_seq_midi snd_seq_midi_event coretemp crct10dif_pclmul crc32_generic crc32_pclmul snd_ens1371 gameport ghash_clmulni_intel snd_ac97_codec f2fs intel_rapl_perf ac97_bus snd_seq ppdev snd_pcm snd_rawmidi snd_timer vmw_balloon snd_seq_device snd joydev soundcore parport_pc parport nfit acpi_cpufreq tpm_tis vmw_vmci tpm_tis_core tpm shpchp i2c_piix4 grace sunrpc xfs libcrc32c vmwgfx drm_kms_helper ttm drm crc32c_intel e1000 mptspi scsi_transport_spi serio_raw mptscsih mptbase ata_generic pata_acpi fjes [last unloaded: nfs_acl] [ 1295.412522] CPU: 0 PID: 12786 Comm: nfsd Tainted: G W 4.11.0-rc1+ #521 [ 1295.412959] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/02/2015 [ 1295.413814] Call Trace: [ 1295.414252] dump_stack+0x63/0x86 [ 1295.414666] __warn+0xcb/0xf0 [ 1295.415087] warn_slowpath_fmt+0x5f/0x80 [ 1295.415502] ? put_filp+0x42/0x50 [ 1295.415927] nfserrno+0x74/0x80 [nfsd] [ 1295.416339] nfsd_open+0xd7/0x180 [nfsd] [ 1295.416746] nfs4_get_vfs_file+0x367/0x3c0 [nfsd] [ 1295.417182] ? security_inode_permission+0x41/0x60 [ 1295.417591] nfsd4_process_open2+0x9b2/0x1200 [nfsd] [ 1295.418007] nfsd4_open+0x481/0x790 [nfsd] [ 1295.418409] nfsd4_proc_compound+0x395/0x680 [nfsd] [ 1295.418812] nfsd_dispatch+0xb8/0x1f0 [nfsd] [ 1295.419233] svc_process_common+0x4d9/0x830 [sunrpc] [ 1295.419631] svc_process+0xfe/0x1b0 [sunrpc] [ 1295.420033] nfsd+0xe9/0x150 [nfsd] [ 1295.420420] kthread+0x101/0x140 [ 1295.420802] ? nfsd_destroy+0x60/0x60 [nfsd] [ 1295.421199] ? kthread_park+0x90/0x90 [ 1295.421598] ret_from_fork+0x2c/0x40 [ 1295.421996] ---[ end trace 0d5a969cd7852e1f ]--- Signed-off-by:
Kinglong Mee <kinglongmee@gmail.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Olga Kornievskaia authored
commit 0e3d3e5d upstream. Commit 63d63cbf "NFSv4.1: Don't recheck delegations that have already been checked" introduced a regression where when a client received BAD_STATEID error it would not send any TEST_STATEID and instead go into an infinite loop of resending the IO that caused the BAD_STATEID. Fixes: 63d63cbf ("NFSv4.1: Don't recheck delegations that have already been checked") Signed-off-by:
Olga Kornievskaia <kolga@netapp.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Alexey Brodkin authored
commit c70c4733 upstream. As reported in STAR 9001165532, an SLC control reg read (for checking busy state) right after SLC invalidate command may incorrectly return NOT busy causing software to NOT spin-wait while operation is underway. (and for some reason this only happens if L1 cache is also disabled - as required by IOC programming model) Suggested workaround is to do an additional Control Reg read, which ensures the 2nd read gets the right status. Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> [vgupta: reworte changelog a bit] Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Eric Biggers authored
commit 9df0eb18 upstream. In the generic XTS and LRW algorithms, for input data > 128 bytes, a temporary buffer is allocated to hold the values to be XOR'ed with the data before and after encryption or decryption. If the allocation fails, the fixed-size buffer embedded in the request buffer is meant to be used as a fallback --- resulting in more calls to the ECB algorithm, but still producing the correct result. However, we weren't correctly limiting subreq->cryptlen in this case, resulting in pre_crypt() overrunning the embedded buffer. Fix this by setting subreq->cryptlen correctly. Fixes: f1c131b4 ("crypto: xts - Convert to skcipher") Fixes: 700cb3f5 ("crypto: lrw - Convert to skcipher") Reported-by:
Eric Biggers <ebiggers@google.com> Acked-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Gary R Hook authored
commit efc989fc upstream. The CCP registers its queues as channels capable of handling general DMA operations. The NTB driver will use DMA if directed, but as public channels can be reserved for use in asynchronous operations some channels should be held back as private. Since the public/private determination is handled at a device level, reserve the "other" (secondary) CCP channels as private. Add a module parameter that allows for override, to be applied to all channels on all devices. Signed-off-by:
Gary R Hook <gary.hook@amd.com> Signed-off-by:
-
Ludovic Desroches authored
commit d0918764 upstream. The controller has different timings for MMC_TIMING_UHS_DDR50 and MMC_TIMING_MMC_DDR52. Configuring the controller with SDHCI_CTRL_UHS_DDR50, when MMC_TIMING_MMC_DDR52 timings are requested, is not correct and can lead to unexpected behavior. Signed-off-by:
Ludovic Desroches <ludovic.desroches@microchip.com> Fixes: bb5f8ea4 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Hans de Goede authored
commit 923713b3 upstream. SDIO cards may need clock to send the card interrupt to the host. On a cherrytrail tablet with a RTL8723BS wifi chip, without this patch pinging the tablet results in: PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data. 64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=78.6 ms 64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1760 ms 64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=753 ms 64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=3.88 ms 64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=795 ms 64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1841 ms 64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=810 ms 64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1860 ms 64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=812 ms 64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=48.6 ms Where as with this patch I get: PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data. 64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=3.96 ms 64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1.97 ms 64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=17.2 ms 64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=2.46 ms 64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=2.83 ms 64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1.40 ms 64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=2.10 ms 64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1.40 ms 64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=2.04 ms 64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=1.40 ms Cc: Dong Aisheng <b29396@freescale.com> Cc: Ian W MORRISON <ianwmorrison@gmail.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Acked-by:
Dong Aisheng <aisheng.dong@nxp.com> Signed-off-by:
-
Aaron Armstrong Skomra authored
commit 8b407359 upstream. A previous commit (below) adds a check for already probed interfaces to Wacom's matching heuristic. Unfortunately this causes the Bamboo Pen (CTL-460) to match itself to its 'ghost' touch interface. After subsequent changes to the driver this match to the ghost causes the kernel to crash. This patch avoids calling wacom_add_shared_data() for the BAMBOO_PEN's ghost touch interface. Fixes: 41372d5d ("HID: wacom: Augment 'oVid' and 'oPid' with heuristics for HID_GENERIC") Signed-off-by:
Aaron Armstrong Skomra <aaron.skomra@wacom.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Bard Liao authored
commit f1994a9c upstream. We got rt5665 private data from wrong work. It will result in kernel panic. Signed-off-by:
Bard Liao <bardliao@realtek.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Takashi Sakamoto authored
commit d1a6fe41 upstream. In 'skl_tplg_set_module_init_data()', a pointer to 'params' member of 'struct skl_algo_data' is calculated, then casted to (u32 *) and assigned to a member of configuration data. The configuration data is passed to the other functions and used to process intel IPC. In this processing, the value of member is used to get message data, however this can bring invalid memory access in 'skl_set_module_params()' as a result of calculation of a pointer for actual message data. (sound/soc/intel/skylake/skl-topology.c) skl_tplg_init_pipe_modules() ->skl_tplg_set_module_init_data() (has this bug) ->skl_tplg_set_module_params() (sound/soc/intel/skylake/skl-messages.c) ->skl_set_module_params() ((char *)param) + data_offset This commit fixes the bug. Fixes: abb74003 ("ASoC: Intel: Skylake: Add support to configure module params") Signed-off-by:
Takashi Sakamoto <takashi.sakamoto@miraclelinux.com> Acked-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Songjun Wu authored
commit cd3ac9af upstream. Fix the audio clock rate according to the datasheet. Reported-by:
Dushara Jayasinghe <dushara@successful.com.au> Signed-off-by:
Songjun Wu <songjun.wu@microchip.com> Acked-by:
-
Hui Wang authored
commit 2f726aec upstream. On this Dell AIO machine, the lineout jack does not work. We found the pin 0x1a is assigned to lineout on this machine, and in the past, we applied ALC298_FIXUP_DELL1_MIC_NO_PRESENCE to fix the heaset-set mic problem for this machine, this fixup will redefine the pin 0x1a to headphone-mic, as a result the lineout doesn't work anymore. After consulting with Dell, they told us this machine doesn't support microphone via headset jack, so we add a new fixup which only defines the pin 0x18 as the headset-mic. [rearranged the fixup insertion position by tiwai in order to make the merge with other branches easier -- tiwai] Fixes: 59ec4b57 ("ALSA: hda - Fix headset mic detection problem for two dell machines") Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 2d7d5400 upstream. When a new event is queued while processing to resize the FIFO in snd_seq_fifo_clear(), it may lead to a use-after-free, as the old pool that is being queued gets removed. For avoiding this race, we need to close the pool to be deleted and sync its usage before actually deleting it. The issue was spotted by syzkaller. Reported-by:
-
Tomasz Nowicki authored
commit 81caa91b upstream. "CAV" is the only PNP/ACPI hardware ID vendor prefix assigned to Cavium so fix this as it should be from day one. Fixes: 44f22bd9 ("PCI: Add MCFG quirks for Cavium ThunderX pass2.x host controller") Tested-by:
Robert Richter <rrichter@cavium.com> Signed-off-by:
Tomasz Nowicki <tn@semihalf.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
-
Bjorn Helgaas authored
commit 6e347b5e upstream. The host bridge memory window resource is inserted into the iomem_resource tree and cannot be deallocated until the host bridge itself is removed. Previously, the window was on the stack, which meant the iomem_resource entry pointed into the stack and was corrupted as soon as the probe function returned, which caused memory corruption and errors like this: pcie_iproc_bcma bcma0:8: resource collision: [mem 0x40000000-0x47ffffff] conflicts with PCIe MEM space [mem 0x40000000-0x47ffffff] Move the memory window resource from the stack into struct iproc_pcie so its lifetime matches that of the host bridge. Fixes: c3245a56 ("PCI: iproc: Request host bridge window resources") Reported-and-tested-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Bart Van Assche authored
commit 7cb689fe upstream. Callers of scsi_dh_activate(), e.g. dm-mpath, assume that this function either returns an error code or calls the completion function. Make alua_activate() call the completion function even if scsi_device_get() fails. Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Tang Junhui <tang.junhui@zte.com.cn> Reviewed-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Bart Van Assche authored
commit 625fe857 upstream. Do not queue ALUA work nor call scsi_device_put() if the scsi_device_get() call fails. This patch fixes the following crash: general protection fault: 0000 [#1] SMP RIP: 0010:scsi_device_put+0xb/0x30 Call Trace: scsi_disk_put+0x2d/0x40 sd_release+0x3d/0xb0 __blkdev_put+0x29e/0x360 blkdev_put+0x49/0x170 dm_put_table_device+0x58/0xc0 [dm_mod] dm_put_device+0x70/0xc0 [dm_mod] free_priority_group+0x92/0xc0 [dm_multipath] free_multipath+0x70/0xc0 [dm_multipath] multipath_dtr+0x19/0x20 [dm_multipath] dm_table_destroy+0x67/0x120 [dm_mod] dev_suspend+0xde/0x240 [dm_mod] ctl_ioctl+0x1f5/0x520 [dm_mod] dm_ctl_ioctl+0xe/0x20 [dm_mod] do_vfs_ioctl+0x8f/0x700 SyS_ioctl+0x3c/0x70 entry_SYSCALL_64_fastpath+0x18/0xad Fixes: commit 03197b61 ("scsi_dh_alua: Use workqueue for RTPG") Signed-off-by:
-
John Garry authored
commit 9702c67c upstream. The total ata xfer length may not be calculated properly, in that we do not use the proper method to get an sg element dma length. According to the code comment, sg_dma_len() should be used after dma_map_sg() is called. This issue was found by turning on the SMMUv3 in front of the hisi_sas controller in hip07. Multiple sg elements were being combined into a single element, but the original first element length was being use as the total xfer length. Fixes: ff2aeb1e ("libata: convert to chained sg") Signed-off-by:
John Garry <john.garry@huawei.com> Signed-off-by:
-
peter chang authored
commit bf33f87d upstream. The user can control the size of the next command passed along, but the value passed to the ioctl isn't checked against the usable max command size. Signed-off-by:
Peter Chang <dpf@google.com> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Christoph Hellwig authored
commit 2fcc319d upstream. When a reflink operation causes the bmap code to allocate a btree block we're currently doing single-AG allocations due to having ->firstblock set and then try any higher AG due a little reflink quirk we've put in when adding the reflink code. But given that we do not have a minleft reservation of any kind in this AG we can still not have any space in the same or higher AG even if the file system has enough free space. To fix this use a XFS_ALLOCTYPE_FIRST_AG allocation in this fall back path instead. [And yes, we need to redo this properly instead of piling hacks over hacks. I'm working on that, but it's not going to be a small series. In the meantime this fixes the customer reported issue] Also add a warning for failing allocations to make it easier to debug. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Brian Foster authored
commit f65e6fad upstream. Commit fa7f138a ("xfs: clear delalloc and cache on buffered write failure") fixed one regression in the iomap error handling code and exposed another. The fundamental problem is that if a buffered write is a rewrite of preexisting delalloc blocks and the write fails, the failure handling code can punch out preexisting blocks with valid file data. This was reproduced directly by sub-block writes in the LTP kernel/syscalls/write/write03 test. A first 100 byte write allocates a single block in a file. A subsequent 100 byte write fails and punches out the block, including the data successfully written by the previous write. To address this problem, update the ->iomap_begin() handler to distinguish newly allocated delalloc blocks from preexisting delalloc blocks via the IOMAP_F_NEW flag. Use this flag in the ->iomap_end() handler to decide when a failed or short write should punch out delalloc blocks. This introduces the subtle requirement that ->iomap_begin() should never combine newly allocated delalloc blocks with existing blocks in the resulting iomap descriptor. This can occur when a new delalloc reservation merges with a neighboring extent that is part of the current write, for example. Therefore, drop the post-allocation extent lookup from xfs_bmapi_reserve_delalloc() and just return the record inserted into the fork. This ensures only new blocks are returned and thus that preexisting delalloc blocks are always handled as "found" blocks and not punched out on a failed rewrite. Reported-by:
Xiong Zhou <xzhou@redhat.com> Signed-off-by:
Brian Foster <bfoster@redhat.com> Reviewed-by:
-
Chandan Rajendra authored
commit d5825712 upstream. When block size is larger than inode cluster size, the call to XFS_B_TO_FSBT(mp, mp->m_inode_cluster_size) returns 0. Also, mkfs.xfs would have set xfs_sb->sb_inoalignmt to 0. Hence in xfs_set_inoalignment(), xfs_mount->m_inoalign_mask gets initialized to -1 instead of 0. However, xfs_mount->m_sinoalign would get correctly intialized to 0 because for every positive value of xfs_mount->m_dalign, the condition "!(mp->m_dalign & mp->m_inoalign_mask)" would evaluate to false. Also, xfs_imap() worked fine even with xfs_mount->m_inoalign_mask having -1 as the value because blks_per_cluster variable would have the value 1 and hence we would never have a need to use xfs_mount->m_inoalign_mask to compute the inode chunk's agbno and offset within the chunk. Signed-off-by:
Chandan Rajendra <chandan@linux.vnet.ibm.com> Reviewed-by:
-
Christoph Hellwig authored
commit 787eb485 upstream. There are two different cases of buffered I/O errors: - first we can have an already shutdown fs. In that case we should skip any on-disk operations and just clean up the appen transaction if present and destroy the ioend - a real I/O error. In that case we should cleanup any lingering COW blocks. This gets skipped in the current code and is fixed by this patch. Signed-off-by:
-
Christoph Hellwig authored
commit 3802a345 upstream. We only want to reclaim preallocations from our periodic work item. Currently this is archived by looking for a dirty inode, but that check is rather fragile. Instead add a flag to xfs_reflink_cancel_cow_* so that the caller can ask for just cancelling unwritten extents in the COW fork. Signed-off-by:
-
Christoph Hellwig authored
commit 410d17f6 upstream. In various places we currently assert that xfs_bmap_btalloc allocates from the same as the firstblock value passed in, unless it's either NULLAGNO or the dop_low flag is set. But the reflink code does not fully follow this convention as it passes in firstblock purely as a hint for the allocator without actually having previous allocations in the transaction, and without having a minleft check on the current AG, leading to the assert firing on a very full and heavily used file system. As even the reflink code only allocates from equal or higher AGs for now we can simply the check to always allow for equal or higher AGs. Note that we need to eventually split the two meanings of the firstblock value. At that point we can also allow the reflink code to allocate from any AG instead of limiting it in any way. Signed-off-by:
-
Chandan Rajendra authored
commit 8ee9fdbe upstream. On a ppc64 system, executing generic/256 test with 32k block size gives the following call trace, XFS: Assertion failed: args->maxlen > 0, file: /root/repos/linux/fs/xfs/libxfs/xfs_alloc.c, line: 2026 kernel BUG at /root/repos/linux/fs/xfs/xfs_message.c:113! Oops: Exception in kernel mode, sig: 5 [#1] SMP NR_CPUS=2048 DEBUG_PAGEALLOC NUMA pSeries Modules linked in: CPU: 2 PID: 19361 Comm: mkdir Not tainted 4.10.0-rc5 #58 task: c000000102606d80 task.stack: c0000001026b8000 NIP: c0000000004ef798 LR: c0000000004ef798 CTR: c00000000082b290 REGS: c0000001026bb090 TRAP: 0700 Not tainted (4.10.0-rc5) MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI> CR: 28004428 XER: 00000000 CFAR: c0000000004ef180 SOFTE: 1 GPR00: c0000000004ef798 c0000001026bb310 c000000001157300 ffffffffffffffea GPR04: 000000000000000a c0000001026bb130 0000000000000000 ffffffffffffffc0 GPR08: 00000000000000d1 0000000000000021 00000000ffffffd1 c000000000dd4990 GPR12: 0000000022004444 c00000000fe00800 0000000020000000 0000000000000000 GPR16: 0000000000000000 0000000043a606fc 0000000043a76c08 0000000043a1b3d0 GPR20: 000001002a35cd60 c0000001026bbb80 0000000000000000 0000000000000001 GPR24: 0000000000000240 0000000000000004 c00000062dc55000 0000000000000000 GPR28: 0000000000000004 c00000062ecd9200 0000000000000000 c0000001026bb6c0 NIP [c0000000004ef798] .assfail+0x28/0x30 LR [c0000000004ef798] .assfail+0x28/0x30 Call Trace: [c0000001026bb310] [c0000000004ef798] .assfail+0x28/0x30 (unreliable) [c0000001026bb380] [c000000000455d74] .xfs_alloc_space_available+0x194/0x1b0 [c0000001026bb410] [c00000000045b914] .xfs_alloc_fix_freelist+0x144/0x480 [c0000001026bb580] [c00000000045c368] .xfs_alloc_vextent+0x698/0xa90 [c0000001026bb650] [c0000000004a6200] .xfs_ialloc_ag_alloc+0x170/0x820 [c0000001026bb7c0] [c0000000004a9098] .xfs_dialloc+0x158/0x320 [c0000001026bb8a0] [c0000000004e628c] .xfs_ialloc+0x7c/0x610 [c0000001026bb990] [c0000000004e8138] .xfs_dir_ialloc+0xa8/0x2f0 [c0000001026bbaa0] [c0000000004e8814] .xfs_create+0x494/0x790 [c0000001026bbbf0] [c0000000004e5ebc] .xfs_generic_create+0x2bc/0x410 [c0000001026bbce0] [c0000000002b4a34] .vfs_mkdir+0x154/0x230 [c0000001026bbd70] [c0000000002bc444] .SyS_mkdirat+0x94/0x120 [c0000001026bbe30] [c00000000000b760] system_call+0x38/0xfc Instruction dump: 4e800020 60000000 7c0802a6 7c862378 3c82ffca 7ca72b78 38841c18 7c651b78 38600000 f8010010 f821ff91 4bfff94d <0fe00000> 60000000 7c0802a6 7c892378 When block size is larger than inode cluster size, the call to XFS_B_TO_FSBT(mp, mp->m_inode_cluster_size) returns 0. Also, mkfs.xfs would have set xfs_sb->sb_inoalignmt to 0. This causes xfs_ialloc_cluster_alignment() to return 0. Due to this args.minalignslop (in xfs_ialloc_ag_alloc()) gets the unsigned equivalent of -1 assigned to it. This later causes alloc_len in xfs_alloc_space_available() to have a value of 0. In such a scenario when args.total is also 0, the assert statement "ASSERT(args->maxlen > 0);" fails. This commit fixes the bug by replacing the call to XFS_B_TO_FSBT() in xfs_ialloc_cluster_alignment() with a call to xfs_icluster_size_fsb(). Suggested-by:
-
Brian Foster authored
commit 48af96ab upstream. The block reservation for the transaction allocated in xfs_shift_file_space() is an artifact of the original collapse range support. It exists to handle the case where a collapse range occurs, the initial extent is left shifted into a location that forms a contiguous boundary with the previous extent and thus the extents are merged. This code was subsequently refactored and reused for insert range (right shift) support. If an insert range occurs under low free space conditions, the extent at the starting offset is split before the first shift transaction is allocated. If the block reservation fails, this leaves separate, but contiguous extents around in the inode. While not a fatal problem, this is unexpected and will flag a warning on subsequent insert range operations on the inode. This problem has been reproduce intermittently by generic/270 running against a ramdisk device. Since right shift does not create new extent boundaries in the inode, a block reservation for extent merge is unnecessary. Update xfs_shift_file_space() to conditionally reserve fs blocks for left shift transactions only. This avoids the warning reproduced by generic/270. Reported-by:
Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by:
-
Darrick J. Wong authored
commit 93aaead5 upstream. Fix an uninitialize variable. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
-
