Normally the native AXP288 fg/charger drivers are preferred but one some
devices the ACPI drivers should be used instead.

The ACPI battery/ac drivers use the acpi_quirk_skip_acpi_ac_and_battery()
helper to determine if they should skip loading because native fuel-gauge/
charger drivers like the AXP288 drivers will be used.

The new acpi_quirk_skip_acpi_ac_and_battery() helper includes a list of
exceptions for boards where the ACPI drivers should be used instead.

Use this new helper to avoid loading on such boards. Note this requires
adding a Kconfig dependency on ACPI, this is not a problem because ACPI
should be enabled on all boards with an AXP288 PMIC anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Use devm_work_autocancel() instead of hand writing it.
It saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Use devm_delayed_work_autocancel() instead of hand writing it.
It saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

This driver only uses managed resources, except for the delayed work, if
it is used.

Use devm_delayed_work_autocancel() to also manage the delayed work.
The error handling path of the probe and the remove function can both be
removed.

This saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

This driver can use an interrupt or polling in order get the charger's
status.

When using polling, a delayed work is used.

However, the remove() function unconditionally call
cancel_delayed_work_sync(), even if the delayed work is not used and is not
initialized.

In order to fix it, use devm_delayed_work_autocancel() and remove the now
useless remove() function.

Fixes: feb583e3 ("power: supply: add sbs-charger driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Adds a brief desciption of the "Long Life" charge type and adds "Long Life"
to the list of valid values.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

This patch remaps the bypass operation from POWER_SUPPLY_CHARGE_TYPE_FAST
to POWER_SUPPLY_CHARGE_TYPE_BYPASS.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Adds a POWER_SUPPLY_CHARGE_TYPE_BYPASS option to the POWER_SUPPLY_PROP_CHARGE_TYPE
property to facilitate bypass charging operation.

In bypass charging operation, the charger bypasses the charging path around the
integrated converter allowing for a "smart" wall adaptor to perform the power
conversion externally.

This operational mode is critical for the USB PPS standard of power adaptors and is
becoming a common feature in modern charging ICs such as:

- BQ25980
- BQ25975
- BQ25960
- LN8000
- LN8410
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Use devm_work_autocancel() instead of hand-writing it.
This saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The smb347 has a very sparse register map (the maximum register is 0x3f but
less than 10% of the possible registers appear to be defined) and doesn't
have any hardware defaults specified so the sparser data structure of an
rbtree is a better fit for it's needs than a flat cache. Since it uses I2C
for the control interface there is no performance concern with the slightly
more involved code so let's convert it.

This will mean we avoid any issues created by assuming that any previously
unaccessed registers hold a value that doesn't match what's in the hardware
(eg, an _update_bits() suppressing a write).
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The AXP288's recommended and factory default Vhold value (minimum
input voltage below which the input current draw will be reduced)
is 4.4V. This lines up with other charger IC's such as the TI
bq2419x/bq2429x series which use 4.36V or 4.44V.

For some reason some BIOS-es initialize Vhold to 4.6V or even 4.7V
which combined with the typical voltage drop over typically low
wire gauge micro-USB cables leads to the input-current getting
capped below 1A (with a 2A capable dedicated charger) based on Vhold.

This leads to slow charging, or even to the device slowly discharging
if the device is in heavy use.

As the Linux AXP288 drivers use the builtin BC1.2 charger detection
and send the input-current-limit according to the detected charger
there really is no reason not to use the recommended 4.4V Vhold.

Set Vhold to 4.4V to fix the slow charging issue on various devices.

There is one exception, the special-case of the HP X2 2-in-1s which
combine this BC1.2 capable PMIC with a Type-C port and a 5V/3A factory
provided charger with a Type-C plug which does not do BC1.2. These
have their input-current-limit hardcoded to 3A (like under Windows)
and use a higher Vhold on purpose to limit the current when used
with other chargers. To avoid touching Vhold on these HP X2 laptops
the code setting Vhold is added to an else branch of the if checking
for these models.

Note this also fixes the sofar unused VBUS_ISPOUT_VHOLD_SET_MASK
define, which was wrong.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Remove unneeded variable used to store return value.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Replace dev_err() with dev_err_probe() in probe() and extend register
access failure messages. dev_err()s in _reset() are removed as they
are redundant: register access wrappers already log the error.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Replace two divisions with a subtraction+shift for a small code size
improvement and less brackets.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

fix the comment typo: "interrupts", "structcure"
Signed-off-by: Hong Peng <elicec@foxmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

kobject_init_and_add() takes reference even when it fails.
According to the doc of kobject_init_and_add()：

   If this function returns an error, kobject_put() must be called to
   properly clean up the memory associated with the object.

Fix memory leak by calling kobject_put().

Fixes: 8c0984e5 ("power: move power supply drivers to power/supply")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

This change makes the PCHG driver receive device events through
MKBP protocol since CrOS EC switched to deliver all peripheral
charge events to the MKBP protocol. This will unify PCHG event
handling on X86 and ARM.
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

When using USB charging, the AB8500 charger is periodically
checking VBAT for a threshold at 3.8V.

This crashes badly, as the class_for_each_device() was passed
the wrong argument. I think this has maybe worked by chance
in the past because of how the structs were arranged but it
is leading to crashes now.

Fix this up and also switch to using microvolts for the
voltages like the rest of the code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The AB8505 only has two ADC channels: the voltage and current
provided from VBUS (USB). It does not support AC charging at all.
Make sure we don't try to retrieve the non-existing channels.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

There is a sysfs ABI to enable/disable charging of different
types (AC/USB).

Since we don't have any userspace for this code, this sits
unused and it is not used on production products either.

Drop this code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

There is a sysfs ABI to change the "charging step" of the
charger i.e. limit how much we charge from userspace.

Since we don't have any userspace for this code, this sits
unused and it is not used on production products either.

Drop this code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

All calls to ab8500_fg_calc_cap_discharge_voltage() require
compensation and pass true as the second argument so just drop
this argument.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

In some cases when the platform is dissapating more than
500mA the voltage measurements and compensation will become
instable. Add a parameter to bail out of the voltage
measurement if this happens.

This code was found in a Samsung vendor tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Break out the part of the function providing the load compensated
capacity that provides the load compensated voltage and use
that to get the load compensated capacity.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

In the Samsung code tree we find that it can happen that this
measurement loop goes on for a long time, and it seems like a
good idea to break it after 70 iterations if it goes on for
too long.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Instead of providing our own homebrewn thermal measurement
code for an NTC and passing tables, we put the NTC thermistor
into the device tree, create a passive thermal zone, and poll
this thermal zone for the temperature.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

We should terminate charging when we reach the voltage_max_design_uv
not overvoltage_limit_uv, this is an abuse of that struct member.

The overvoltage limit is actually not configurable on the AB8500,
it is fixed to 4.75 V so drop a comment about that in the code.

Fixes: 2a5f4183 ("power: supply: ab8500: Standardize voltages")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

The BATCTRL mode reads the temperature of the battery by
enabling a certain probing current (7-20 mA) and then measure
the voltage of the NTC mounted inside the battery.

None of the AB8500 product or the reference designs use this
mode. What we use is the so-called BATTEMP mode which enables
an internal 230 kOhm pull-up to 1.8 V to the external NTC on
pin BatTemp (N16) and then measures the voltage over the NTC
using the ADC:

        1.8V (VTVOUT)
         |
        [ ] 230 kOhm
         |
BatTemp  +---------------- ADC
Pin N16  | _
         |/
        [/] NTC
       _/|
         |
        GND

Cut out the BATCTRL code to clear the forest and stop
maintaining code we can never test.

The current inducing method is still used to probe for the
battery type using the internal BTI (battery type indicator)
on the BatCtrl (C3) pin in a separate code path.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Use device_property_string_array_count() to get number of strings
in a string array property.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

When ret is not zero there were already one or two error messages emitted
about a problem (because rt9455_register_reset() emits a message in most
cases then). Passing on that error code to the i2c core only results in
another error message. Suppress that by returning zero unconditionally.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Use devm_bitmap_zalloc() instead of hand writing it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add a new battery driver for the uPI uG3105 battery monitor.

Note the uG3105 is not a full-featured autonomous fuel-gauge. Instead it
is expected to be use in combination with some always on microcontroller
reading its coulomb-counter before it can wrap (must be read every 400
seconds!).

Since Linux does not monitor coulomb-counter changes while the device is
off or suspended, the coulomb counter is not used atm.

So far this driver is only used on x86/ACPI (non devicetree) devs
(also note there is no of_match table). Therefor there is no devicetree
bindings documentation for this driver's "upisemi,rsns-microohm" property
since this is not used in actual devicetree files and the dt bindings
maintainers have requested properties with no actual dt users to
_not_ be added to the dt bindings.

The property's name has been chosen so that it should not need to be
changed if/when devicetree enumeration support gets added later, as it
mirrors "maxim,rsns-microohm" from the "maxim,max17042" bindings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

If the fwnode data as parsed by power_supply_get_battery_info() provides
max values for ccc_ireg and cvc_vreg then do not allow the user to later
set these to higher values then those specified by the firmware,
otherwise the battery might get damaged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

So far the bq24190_charger driver has been relying on either the chips
default constant_charge_current_max_ua and constant_charge_voltage_max_uv
values, or on the BIOS or bootloader to program these for us.

This does not happen on all boards, causing e.g. the wrong (too low)
values to be used on Lenovo Yoga Tablet 2 830F/L and 1050F/L tablets.

If power_supply_get_battery_info() provides us with values for these
settings, then program the charger accordingly.

And if the user later overrides these values then save the user-values
so that these will be restored after a suspend/resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Store ichg-max and vreg-max in bq24190_dev_info once from
bq24190_get_config() and drop the bq24190_charger_get_current_max() and
bq24190_charger_get_voltage_max() helpers.

This is a preparation patch for honoring the
constant_charge_current_max_ua and constant_charge_voltage_max_uv
values from power_supply_get_battery_info().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

power_supply_get_battery_info() now also supports getting battery_info
on boards not using dt/of. Remove the of_node check. If neither of nor
other battery-info is present the function will fail making this change
a no-op in that case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Turn off the 5V boost regulator on shutdown, there are 3 reasons for
doing this:

1. It drains he battery if left on
2. If left on the device will not charge when plugged into a charger
3. If left on and the powered peripheral attached to a Type-C port is
   removed before the next boot, then the Type-C port-controller will
   see VBus being present while nothing is attached confusing the
   TCPM state-machine.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Add support to power_supply_get_battery_info() to read the properties from
other fwnode types such as swnodes added by platform code on x86 devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

Switch power_supply_get_battery_info() over to use the generic
fwnode_property_*() property read functions. This is a preparation patch
for adding support for reading properties from other fwnode types such
as swnode properties added by platform code on x86 devices.

Note the parsing of the 2d matrix "ocv-capacity-table-%d" and
"resistance-temp-table" properties is not converted since this depends on
the raw of_get_property() accessor function of which there is no
fwnode_property_*() equivalent AFAICT. This means that these properties
will not be supported in swnodes for now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>

There is a spelling mistake in a MODULE_PARM_DESC description. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>