This SoC features an ARM CCI-400 IP: add the required node and
assign the cci control ports to the CPU cores.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-9-angelogioacchino.delregno@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add the timer node, enabling two GPTs, of which one will be used as
sched_clock.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-8-angelogioacchino.delregno@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Remove the RTC and UART fixed clocks, as these were introduced to
temporarily provide a dummy clock to devices: since the two 26M/32K
fixed oscillators clocks (which do really exist in the SoC) have
been added, there's no reason to keep the aforementioned (and now
redundant) dummies in this devicetree.

In order to remove the uart dummy clock, it was necessary to also
reassign the clock of all UART nodes to clk26m.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-7-angelogioacchino.delregno@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add the 32kHz and 26MHz oscillators as fixed clocks in devicetree to
provide a good initial clock spec, since this SoC features two always
on oscillators running at the aforementioned frequencies.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-6-angelogioacchino.delregno@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

At least on commercial devices like some smartphones, the bootloader
will initialize the SoC watchdog and set it to reboot the board when
it times out. The last pet that this watchdog is getting is right
before booting the kernel and left it enabled as a protection against
boot failure: this means that Linux is expected to initialize this
device and pet as soon as possible, or it will bark and reset the AP.

In order to prevent that, add the required watchdog node as default
enabled: this will have no side effects on boards that are not
performing the aforementioned watchdog setup before booting Linux.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-5-angelogioacchino.delregno@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add the required nodes to enable the PMU on this SoC.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-4-angelogioacchino.delregno@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

This SoC is HMP and has two clusters with four Cortex-A53 cores each:
declare a cpu map and, while at it, also add the next-level-cache
properties.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-3-angelogioacchino.delregno@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

MMIO devices should be inside of a soc bus node, as it's done for the
vast majority of ARM64 devicetrees, and for almost all MTK devicetrees.
Create a simple-bus soc node and move all devices with a MMIO address
space in there.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220609112303.117928-2-angelogioacchino.delregno@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

gpio-keys (regular, not polling) does not use "poll-interval" property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220617232124.7022-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

The IOMMU driver now looks for the "mediatek,infracfg" phandle as a
new way to retrieve a syscon to that:
even though the old way is retained, it has been deprecated and the
driver will write a message in kmsg advertising to use the phandle
way instead.

For this reason, assign the right phandle to mediatek,infracfg in
the iommu node.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220616110830.26037-5-angelogioacchino.delregno@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

The IOMMU driver now looks for the "mediatek,infracfg" phandle as a
new way to retrieve a syscon to that:
even though the old way is retained, it has been deprecated and the
driver will write a message in kmsg advertising to use the phandle
way instead.

For this reason, assign the right phandle to mediatek,infracfg in
the iommu node.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220616110830.26037-4-angelogioacchino.delregno@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Use the fixed "efuse" name for efuse nodes according to its yaml file
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220617093132.22578-4-chunfeng.yun@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Need also provide a specific compatible "mediatek,mt8192-efuse" at
the same time when use the generic compatible "mediatek,efuse".
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220617093132.22578-3-chunfeng.yun@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

The entry-method property of the idle-states node should be "psci" as
described in the idle-states binding, since this is already the value of
enable-method in the CPU nodes. Fix it to get rid of a dtbs_check
warning.

Fixes: 9260918d ("arm64: dts: mt8192: Add cpu-idle-states")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220617233150.2466344-3-nfraprado@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Tweak the name of the idle-states subnodes so that they follow the
binding pattern, getting rid of dtbs_check warnings.

Only the usage of "-" in the name was necessary, but "off" was also
exchanged for "sleep" since that seems to be a more common wording in
other dts files.

Fixes: 9260918d ("arm64: dts: mt8192: Add cpu-idle-states")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220617233150.2466344-2-nfraprado@collabora.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

As explained in Documentation/devicetree/bindings/mmc/mmc-controller.yaml,
the 'enable-sdio-wakeup' property is considered deprecated.

Replace it with the 'wakeup-source' property instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220621124435.121740-1-festevam@gmail.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

We will use mediatek clock reset as infracfg_ao reset instead of
ti-syscon. To support this, remove property of ti reset and add
property of #reset-cells for mediatek clock reset.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220503093856.22250-17-rex-bc.chen@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

To support reset of infra, we add property of #reset-cells.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220503093856.22250-16-rex-bc.chen@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

In order to allow modules with latency requirements such as MDP3
to set registers through CMDQ, add the relevant dts property.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://lore.kernel.org/r/20220610063424.7800-6-moudy.ho@mediatek.com
[mb: fix commit subject]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

The node names should be generic and DT schema expects certain pattern
with 'led'.  Use generic color properties instead of the node name.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-16-krzysztof.kozlowski@linaro.orgSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-15-krzysztof.kozlowski@linaro.orgSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment.  No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220526204402.832393-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Enable USB remote wakeup of all four xHCI controller
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220617072344.21461-2-chunfeng.yun@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add efuse node and cells used by t-phy to fix the bit shift issue
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220617072344.21461-1-chunfeng.yun@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add compatible/reg/irq/clock/efuse setting in svs node.
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20220516004311.18358-3-roger.lu@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add mediatek,cci property to support MediaTek CCI feature.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220516111130.13325-4-rex-bc.chen@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add MediaTek CCI devfreq node for MT8183.
Signed-off-by: Andrew-sh.Cheng <andrew-sh.cheng@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220516111130.13325-3-rex-bc.chen@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

- Add cpufreq opp table.
- Add MediaTek cci opp table.
- Add property of opp table and clock fro cpufreq.
Signed-off-by: Andrew-sh.Cheng <andrew-sh.cheng@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220516111130.13325-2-rex-bc.chen@mediatek.comSigned-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Pull file descriptor fix from Al Viro:
 "Fix for breakage in #work.fd this window"

* tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix the breakage in close_fd_get_file() calling conventions change

Pull mm hotfixes from Andrew Morton:
 "Fixups for various recently-added and longer-term issues and a few
  minor tweaks:

   - fixes for material merged during this merge window

   - cc:stable fixes for more longstanding issues

   - minor mailmap and MAINTAINERS updates"

* tag 'mm-hotfixes-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  mm/oom_kill.c: fix vm_oom_kill_table[] ifdeffery
  x86/kexec: fix memory leak of elf header buffer
  mm/memremap: fix missing call to untrack_pfn() in pagemap_range()
  mm: page_isolation: use compound_nr() correctly in isolate_single_pageblock()
  mm: hugetlb_vmemmap: fix CONFIG_HUGETLB_PAGE_FREE_VMEMMAP_DEFAULT_ON
  MAINTAINERS: add maintainer information for z3fold
  mailmap: update Josh Poimboeuf's email

Pull delay-accounting update from Andrew Morton:
 "A single featurette for delay accounting.

  Delayed a bit because, unusually, it had dependencies on both the
  mm-stable and mm-nonmm-stable queues"

* tag 'mm-nonmm-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  delayacct: track delays from write-protect copy

The bluetooth code uses our bitmap infrastructure for the two bits (!)
of connection setup flags, and in the process causes odd problems when
it converts between a bitmap and just the regular values of said bits.

It's completely pointless to do things like bitmap_to_arr32() to convert
a bitmap into a u32.  It shoudln't have been a bitmap in the first
place.  The reason to use bitmaps is if you have arbitrary number of
bits you want to manage (not two!), or if you rely on the atomicity
guarantees of the bitmap setting and clearing.

The code could use an "atomic_t" and use "atomic_or/andnot()" to set and
clear the bit values, but considering that it then copies the bitmaps
around with "bitmap_to_arr32()" and friends, there clearly cannot be a
lot of atomicity requirements.

So just use a regular integer.

In the process, this avoids the warnings about erroneous use of
bitmap_from_u64() which were triggered on 32-bit architectures when
conversion from a u64 would access two words (and, surprise, surprise,
only one word is needed - and indeed overkill - for a 2-bit bitmap).

That was always problematic, but the compiler seems to notice it and
warn about the invalid pattern only after commit 0a97953f ("lib: add
bitmap_{from,to}_arr64") changed the exact implementation details of
'bitmap_from_u64()', as reported by Sudip Mukherjee and Stephen Rothwell.

Fixes: fe92ee64 ("Bluetooth: hci_core: Rework hci_conn_params flags")
Link: https://lore.kernel.org/all/YpyJ9qTNHJzz0FHY@debian/
Link: https://lore.kernel.org/all/20220606080631.0c3014f2@canb.auug.org.au/
Link: https://lore.kernel.org/all/20220605162537.1604762-1-yury.norov@gmail.com/Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It used to grab an extra reference to struct file rather than
just transferring to caller the one it had removed from descriptor
table.  New variant doesn't, and callers need to be adjusted.

Reported-and-tested-by: syzbot+47dd250f527cb7bebf24@syzkaller.appspotmail.com
Fixes: 6319194e ("Unify the primitives for file descriptor closing")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull x86 SGX fix from Thomas Gleixner:
 "A single fix for x86/SGX to prevent that memory which is allocated for
  an SGX enclave is accounted to the wrong memory control group"

* tag 'x86-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/sgx: Set active memcg prior to shmem allocation

Pull x86 mm cleanup from Thomas Gleixner:
 "Use PAGE_ALIGNED() instead of open coding it in the x86/mm code"

* tag 'x86-mm-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Use PAGE_ALIGNED(x) instead of IS_ALIGNED(x, PAGE_SIZE)

Pull x86 microcode updates from Thomas Gleixner:

 - Disable late microcode loading by default. Unless the HW people get
   their act together and provide a required minimum version in the
   microcode header for making a halfways informed decision its just
   lottery and broken.

 - Warn and taint the kernel when microcode is loaded late

 - Remove the old unused microcode loader interface

 - Remove a redundant perf callback from the microcode loader

* tag 'x86-microcode-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode: Remove unnecessary perf callback
  x86/microcode: Taint and warn on late loading
  x86/microcode: Default-disable late loading
  x86/microcode: Rip out the OLD_INTERFACE

Pull x86 cleanups from Thomas Gleixner:
 "A set of small x86 cleanups:

   - Remove unused headers in the IDT code

   - Kconfig indendation and comment fixes

   - Fix all 'the the' typos in one go instead of waiting for bots to
     fix one at a time"

* tag 'x86-cleanups-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: Fix all occurences of the "the the" typo
  x86/idt: Remove unused headers
  x86/Kconfig: Fix indentation of arch/x86/Kconfig.debug
  x86/Kconfig: Fix indentation and add endif comments to arch/x86/Kconfig

Pull x86 boot update from Thomas Gleixner:
 "Use strlcpy() instead of strscpy() in arch_setup()"

* tag 'x86-boot-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/setup: Use strscpy() to replace deprecated strlcpy()

Pull clockevent/clocksource updates from Thomas Gleixner:

 - Device tree bindings for MT8186

 - Tell the kernel that the RISC-V SBI timer stops in deeper power
   states

 - Make device tree parsing in sp804 more robust

 - Dead code removal and tiny fixes here and there

 - Add the missing SPDX identifiers

* tag 'timers-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
  clocksource/drivers/timer-ti-dm: Remove unnecessary NULL check
  clocksource/drivers/timer-sun5i: Convert to SPDX identifier
  clocksource/drivers/timer-sun4i: Convert to SPDX identifier
  clocksource/drivers/pistachio: Convert to SPDX identifier
  clocksource/drivers/orion: Convert to SPDX identifier
  clocksource/drivers/lpc32xx: Convert to SPDX identifier
  clocksource/drivers/digicolor: Convert to SPDX identifier
  clocksource/drivers/armada-370-xp: Convert to SPDX identifier
  clocksource/drivers/mips-gic-timer: Convert to SPDX identifier
  clocksource/drivers/jcore: Convert to SPDX identifier
  clocksource/drivers/bcm_kona: Convert to SPDX identifier
  clocksource/drivers/sp804: Avoid error on multiple instances
  clocksource/drivers/riscv: Events are stopped during CPU suspend
  clocksource/drivers/ixp4xx: Drop boardfile probe path
  dt-bindings: timer: Add compatible for Mediatek MT8186