This patch converts the sh architecture to use the generic
read_persistent_clock and update_persistent_clock interfaces, reducing
the amount of arch specific code we have to maintain, and allowing for
further cleanups in the future.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

... so the "sh_debugfs_root" is already available. Previously it
wasn't and in result its path was "/sys/kernel/debug/pmb" instead of
"/sys/kernel/debug/sh/pmb".
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

flush_cache_all() uses broadcast IPIs, so we can't wrap in to that when
IRQs are disabled. The local cache flush manages to do what we need here
anyways, so just switch to that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Presently we run in to issues with the MMU resetting the CPU when
variable sized mappings are employed. This takes a slightly more
aggressive approach to keeping the TLB and cache state sane before
establishing the mappings in order to cut down on races observed on
SMP configurations.

At the same time, we bump the VMA range up to the 0xb000...0xc000 range,
as there still seems to be some undocumented behaviour in setting up
variable mappings in the 0xa000...0xb000 range, resulting in reset by the
TLB.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

In the case of NUMA emulation when in range PPNs are being used for
secondary nodes, we need to make sure that the PMB has a mapping for it
before setting up the pgdat. This prevents the MMU from resetting.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

When entries are being bolted unconditionally it's possible that the boot
loader has established mappings that are within range that we don't want
to clobber. Perform some basic validation to ensure that the new mapping
is out of range before allowing the entry setup to take place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This moves the pmb_remap_caller() mapping logic out in to
pmb_bolt_mapping(), which enables us to establish fixed mappings in
places such as the NUMA code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This plugs in an early_param for permitting transparent PMB-backed
ioremapping to be enabled/disabled. For the time being, we use a
default-disabled policy.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This implements a fairly significant overhaul of the dynamic PMB mapping
code. The primary change here is that the PMB gets its own VMA that
follows the uncached mapping and we attempt to be a bit more intelligent
with dynamic sizing, multi-entry mapping, and so forth.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Trivial build fix, following the change from asm-generic/topology.h.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The recent sh-sci DMA support introduces a number of trivial build
warnings, clean them up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

ctrl_read/writeX are deprecated, this converts them over to their
__raw_read/write() counterparts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Support using DMA for sending and receiving data over SCI(F) interfaces of
various SH SoCs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch extends the .device_terminate_all() method of the shdma driver
to return number of bytes transfered in the current descriptor.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

DMA CHCR register layout is equal on sh7722 and sh7724, reuse definitions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Provided platforms implement runtime PM, this disables the controller, when not
in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Separate SH DMA headers into ones, commonly used by both drivers, and ones,
specific to each of them. This will make the future development of the
dmaengine driver easier.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The shdma dmaengine driver currently uses numerous macros to support various
platforms, selected by ifdef's. Convert it to use platform device resources and
lists of channel descriptors to specify register locations, interrupt numbers
and other system-specific configuration variants. Unavoidably, we have to
simultaneously convert all shdma users to provide those resources.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Present DMA error ISR in shdma.c is bogus, it locks the system hard in multiple
ways. Fix it to abort all queued transactions on all channels on the affected
controller and giving submitters a chance to get a DMA_ERROR status for aborted
transactions. Afterwards further functionality is again possible without the
need to re-load the driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Configure SIU port B pins and register the WM8978 audio codec.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch is required to use the SIU ASoC driver on sh7722 systems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Merge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci

* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits)
  DaVinci DM365: Adding support for SPI EEPROM
  DaVinci DM365: Adding DM365 SPI support
  DaVinci DM355: Modifications to DM355 SPI support
  DaVinci: SPI: Adding header file for SPI support.
  davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup
  davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table()
  DaVinci: DM365: Voice codec support for the DM365 SoC
  davinci: clock: let clk->set_rate function sleep
  Add SDA and SCL pin numbers to i2c platform data
  davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138
  davinci: build list of unused EDMA events dynamically
  davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case
  davinci: Keep count of channel controllers on a platform
  davinci: Correct return value of edma_alloc_channel api
  davinci: add CDCE949 support on DM6467 EVM
  davinci: add support for CDCE949 clock synthesizer
  davinci: da850/omap-l138 EVM: register for suspend support
  davinci: da850/omap-l138: add support for SoC suspend
  davinci: add power management support
  DaVinci: DM365: Changing default queue for DM365.
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (38 commits)
  sata_via: Delay on vt6420 when starting ATAPI DMA write
  ata: Detect Delkin Devices compact flash
  pata_efar: Enable parallel scanning
  pata_atiixp: enable parallel scan
  [libata] pata_atiixp: add locking for parallel scanning
  [libata] pata_efar: add locking for parallel scanning
  libata: Pass host flags into the pci helper
  [libata] pata_marvell: CONFIG_AHCI is really CONFIG_SATA_AHCI
  libata: Allow pata_legacy to be built on non-ISA but PCI systems
  pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsets
  pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cards
  [libata] pata_at91: fix backslash-continued string
  pata_via: store UDMA masks in via_isa_bridges table
  pata_via: fix address setup timings underlocking
  pata_serverworks: fix error message
  pata_serverworks: fix PIO setup for the second channel
  pata_efar: fix secondary port support
  pata_cypress: fix PIO timings underclocking
  pata_cs5535: use correct values for PIO1 and PIO2 data timings
  pata_cmd64x: remove unused definitions
  ...

When writing a disc on certain lite-on dvd-writers (also rebadged
as optiarc/LG/...) connected to a vt6420, the ATAPI CDB ends
up in the datastream and on the disc, causing silent corruption.
Delaying between sending the CDB and starting DMA seems to
prevent this.

I do not know if there are burners that do not suffer from
this, but the patch should be safe for those as well.

There are many reports of this issue, but AFAICT no solution was
found before. For example:
http://lkml.indiana.edu/hypermail/linux/kernel/0802.3/0561.htmlSigned-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

I have a Delkin Devices compact flash card that isn't being recognized using the
SATA/PATA drivers.
The card is recognized and works with the deprecated ATA drivers.

The error I am seeing is:
ata1.00: failed to IDENTIFY (device reports invalid type, err_mask=0x0)

I tracked it down to ata_id_is_cfa() in include/linux/ata.h.
The Delkin card has id[0] set to 0x844a and id[83] set to 0.
This isn't what the kernel expects and is probably incorrect.

The simplest work-around is to add a check for 0x844a to ata_id_is_cfa().
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Again originally proposed by Bartlomiej but this does it by using the
generic helper logic instead.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This was originally proposed by Bartlomiej but as a device specific
expansion of the init_one function rather than making the helper more
generic.

Enable the parallel scan via the generic flags.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This is similar change as commit 60c3be38 for ata_piix host driver
and while pata_atiixp doesn't enable parallel scan yet the race
could probably also be triggered by requesting re-scanning of both
ports at the same time using SCSI sysfs interface.

[Ported to current tree without other patch dependancies by Alan Cox]

Original is
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This one is
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Add clearing of UDMA enable bit also for PIO modes and then add
extra locking for parallel scanning.

This is similar change as commit 60c3be38 for ata_piix host driver
and while pata_efar doesn't enable parallel scan yet the race could
probably also be triggered by requesting re-scanning of both ports
at the same time using SCSI sysfs interface.

[Ported to current kernel without other patch dependancies by
 Alan Cox]

Original is
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This one is
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This allows parallel scan and the like to be set without having to stop
using the existing full helper functions. This patch merely adds the argument
and fixes up the callers. It doesn't undo the special cases already in the
tree or add any new parallel callers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The marvell driver comtains a fallback to ahci for the sata ports
which is incorrectly checked as CONFIG_AHCI while the only AHCI config
item is actually called SATA_AHCI (which also sounds sensible
considering it's a fallback for the sata ports).
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This is needed for some unsupported hardware setups on strange 64bit
mainboards where crazy stuff has been done like putting flash ata adapters
on the LPC bus, or where the real hardware is hidden/confused.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

PDC2026x chipsets need the same treatment as PDC20246 one.

This is completely untested but will hopefully fix UDMA issues
that people have been reporting against pata_pdc202xx_old for
the last couple of years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

On Monday 04 January 2010 02:30:24 pm Russell King wrote:

> Found the problem - getting rid of the read of the alt status register
> after the command has been written fixes the UDMA CRC errors on write:
>
> @@ -676,7 +676,8 @@ void ata_sff_exec_command(struct ata_port *ap, const struct
> ata_taskfile *tf)
>         DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
>
>         iowrite8(tf->command, ap->ioaddr.command_addr);
> -       ata_sff_pause(ap);
> +       ndelay(400);
> +//     ata_sff_pause(ap);
>  }
>  EXPORT_SYMBOL_GPL(ata_sff_exec_command);
>
>
> This rather makes sense.  The PDC20247 handles the UDMA part of the
> protocol.  It has no way to tell the PDC20246 to wait while it suspends
> UDMA, so that a normal register access can take place - the 246 ploughs
> on with the register access without any regard to the state of the 247.
>
> If the drive immediately starts the UDMA protocol after a write to the
> command register (as it probably will for the DMA WRITE command), then
> we'll be accessing the taskfile in the middle of the UDMA setup, which
> can't be good.  It's certainly a violation of the ATA specs.

Fix it by adding custom ->sff_exec_command method for UDMA33 chipsets.
Debugged-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Noticed and rough patch by Joe Perches.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

* store UDMA masks in via_isa_bridges[] and while at it make "flags"
  field to be u8 instead of u16

* convert the driver to use UDMA masks from via_isa_bridges[]

* remove no longer needed VIA_UDMA* defines

Make some minor documentation and CodingStyle fixes while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Correct via_do_set_mode() documentation while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>