- 05 Oct, 2017 3 commits
-
-
Lu Baolu authored
This adds debugfs consumer for xHCI driver. The debugfs entries read all host registers, device/endpoint contexts, command ring, event ring and various endpoint rings. With these entries, users can check the registers and memory spaces used by a host during run time, or save all the information with a simple 'cp -r' for post-mortem programs. The file hierarchy looks like this. [root of debugfs] |__usb |____[e,u,o]hci <---------[root for other HCIs] |____xhci <---------------[root for xHCI] |______0000:00:14.0 <--------------[xHCI host name] |________reg-cap <--------[capability registers] |________reg-op <-------[operational registers] |________reg-runtime <-----------[runtime registers] |________reg-ext-#cap_name <----[extended capability regs] |________command-ring <-------[root for command ring] |__________cycle <------------------[ring cycle] |__________dequeue <--------[ring dequeue pointer] |__________enqueue <--------[ring enqueue pointer] |__________trbs <-------------------[ring trbs] |________event-ring <---------[root for event ring] |__________cycle <------------------[ring cycle] |__________dequeue <--------[ring dequeue pointer] |__________enqueue <--------[ring enqueue pointer] |__________trbs <-------------------[ring trbs] |________devices <------------[root for devices] |__________#slot_id <-----------[root for a device] |____________name <-----------------[device name] |____________slot-context <----------------[slot context] |____________ep-context <-----------[endpoint contexts] |____________ep#ep_index <--------[root for an endpoint] |______________cycle <------------------[ring cycle] |______________dequeue <--------[ring dequeue pointer] |______________enqueue <--------[ring enqueue pointer] |______________trbs <-------------------[ring trbs] Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mathias Nyman authored
Shows the port speed protocol speed ID (PSID) in use. speed ID may map to custom speeds, but in most cases it uses default 1 = Full-Speed 12 MB/s 2 = Low-Speed 1.5 Mb/s 3 = High-speed 480 Mb/s 4 = SuperSpeed 5 Gb/s 5 = SuperSpeedPlus 10 Gb/s Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thang Q. Nguyen authored
XHCI specification 1.1 does not require xHCI-compliant controllers to always enable hardware USB2 LPM. However, the current xHCI driver always enable it when seeing HLC=1. This patch supports an option for users to control disabling USB2 Hardware LPM via DT/ACPI attribute. This option is needed in case user would like to disable this feature. For example, their xHCI controller has its USB2 HW LPM broken. Signed-off-by: Tung Nguyen <tunguyen@apm.com> Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 04 Oct, 2017 19 commits
-
-
Allen Pais authored
Use setup_timer function instead of initializing timer with the function and data fields. Signed-off-by: Allen Pais <allen.lkml@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Allen Pais authored
Use setup_timer function instead of initializing timer with the function and data fields. Signed-off-by: Allen Pais <allen.lkml@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Allen Pais authored
Use setup_timer function instead of initializing timer with the function and data fields. Signed-off-by: Allen Pais <allen.lkml@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Allen Pais authored
Use setup_timer function instead of initializing timer with the function and data fields. Signed-off-by: Allen Pais <allen.lkml@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Allen Pais authored
Use setup_timer function instead of initializing timer with the function and data fields. Signed-off-by: Allen Pais <allen.lkml@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Allen Pais authored
Use setup_timer function instead of initializing timer with the function and data fields. Signed-off-by: Allen Pais <allen.lkml@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Allen Pais authored
Use setup_timer function instead of initializing timer with the function and data fields. Signed-off-by: Allen Pais <allen.lkml@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Allen Pais authored
Use setup_timer function instead of initializing timer with the function and data fields. Signed-off-by: Allen Pais <allen.lkml@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Allen Pais authored
Use setup_timer function instead of initializing timer with the function and data fields. Signed-off-by: Allen Pais <allen.lkml@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Romain Izard authored
When an Atmel SoC is suspended with the backup mode, the USB bus will be powered down. As this is expected, do not return an error to the driver core when ehci_resume detects it. Signed-off-by: Romain Izard <romain.izard.pro@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
Remove the special SA1111 MMIO accessors from the ohci-sa1111 driver as their definition will be removed shortly. The SA1111 accessors are barrierless, so use the _relaxed variants. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
Convert the shutdown method to use the device_driver shutdown function pointer rather than a private bus-type shutdown. This is the only user for SA1111 bus types, so having the support code in the bus doesn't make any sense. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Russell King authored
Use the provided sa1111_get_irq() to fetch the IRQ resources for the SA1111 OHCI driver. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Heikki Krogerus authored
Driver for TI TPS65982, TPS65983 and other TPS6598x family stand alone USB Power Delivery controllers. The driver will at this stage only register the port and partners attached to it, so cables and alternate modes are not yet registered. Both power and data role swapping is supported. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Heikki Krogerus authored
This patch makes the driver work with USB Type-C Port Manager (tcpm.c) to provide USB PD functionality. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Kees Cook authored
The .data assignment appears to be redundant to the WORK_STOP bit for stopping the timer. Also, it appears this timer is entirely unused as it is only ever started under #define VERBOSE, which is explicitly undefined. Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jules Maselbas authored
Adds bindings documentation for the max3421 driver. Signed-off-by: Jules Maselbas <jules.maselbas@grenoble-inp.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jules Maselbas authored
Adds support for devicetree to the max3421 driver. Signed-off-by: Jules Maselbas <jules.maselbas@grenoble-inp.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ben Hutchings authored
usbip_host_driver.h now depends on several additional headers, which need to be installed along with it. Fixes: 021aed84 ("staging: usbip: userspace: migrate usbip_host_driver ...") Fixes: 3391ba0e ("usbip: tools: Extract generic code to be shared with ...") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Acked-by: Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 18 Sep, 2017 7 commits
-
-
Colin Ian King authored
Don't populate const arrays on the stack, instead make them static. Makes the object code smaller by over 1070 bytes: Before: text data bss dec hex filename 3505 880 0 4385 1121 drivers/usb/storage/option_ms.o After: text data bss dec hex filename 2269 1040 0 3309 ced drivers/usb/storage/option_ms.o Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Harsha Sharma authored
Make code more concise and readable Signed-off-by: Harsha Sharma <harshasharmaiitr@gmail.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Guenter Roeck authored
The driver is in good enough shape to be moved out of staging. Do it. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Guenter Roeck authored
Move tcpm (USB Type-C Port Manager) out of staging. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Guenter Roeck authored
struct pd_message is the format of a PD message as seen on the wire. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Guenter Roeck authored
Document struct tcpc_config and struct tcpc_dev. Drop unused TCPC_USB_SWITCH_RESTORE. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Guenter Roeck authored
Commented out code can be added as needed. Drop it. Also drop TODO and an obsolete XXX comment. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 16 Sep, 2017 11 commits
-
-
Linus Torvalds authored
-
git://git.infradead.org/linux-ubifsLinus Torvalds authored
Pull UBI updates from Richard Weinberger: "Minor improvements" * tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs: UBI: Fix two typos in comments ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate" ubi: pr_err() strings should end with newlines ubi: pr_err() strings should end with newlines ubi: pr_err() strings should end with newlines
-
git://git.kernel.org/pub/scm/linux/kernel/git/rw/umlLinus Torvalds authored
Pull UML updates from Richard Weinberger: - minor improvements - fixes for Debian's new gcc defaults (pie enabled by default) - fixes for XSTATE/XSAVE to make UML work again on modern systems * 'for-linus-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml: um: return negative in tuntap_open_tramp() um: remove a stray tab um: Use relative modversions with LD_SCRIPT_DYN um: link vmlinux with -no-pie um: Fix CONFIG_GCOV for modules. Fix minor typos and grammar in UML start_up help um: defconfig: Cleanup from old Kconfig options um: Fix FP register size for XSTATE/XSAVE
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix hotplug deadlock in hv_netvsc, from Stephen Hemminger. 2) Fix double-free in rmnet driver, from Dan Carpenter. 3) INET connection socket layer can double put request sockets, fix from Eric Dumazet. 4) Don't match collect metadata-mode tunnels if the device is down, from Haishuang Yan. 5) Do not perform TSO6/GSO on ipv6 packets with extensions headers in be2net driver, from Suresh Reddy. 6) Fix scaling error in gen_estimator, from Eric Dumazet. 7) Fix 64-bit statistics deadlock in systemport driver, from Florian Fainelli. 8) Fix use-after-free in sctp_sock_dump, from Xin Long. 9) Reject invalid BPF_END instructions in verifier, from Edward Cree. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits) mlxsw: spectrum_router: Only handle IPv4 and IPv6 events Documentation: link in networking docs tcp: fix data delivery rate bpf/verifier: reject BPF_ALU64|BPF_END sctp: do not mark sk dumped when inet_sctp_diag_fill returns err sctp: fix an use-after-free issue in sctp_sock_dump netvsc: increase default receive buffer size tcp: update skb->skb_mstamp more carefully net: ipv4: fix l3slave check for index returned in IP_PKTINFO net: smsc911x: Quieten netif during suspend net: systemport: Fix 64-bit stats deadlock net: vrf: avoid gcc-4.6 warning qed: remove unnecessary call to memset tg3: clean up redundant initialization of tnapi tls: make tls_sw_free_resources static sctp: potential read out of bounds in sctp_ulpevent_type_enabled() MAINTAINERS: review Renesas DT bindings as well net_sched: gen_estimator: fix scaling error in bytes/packets samples nfp: wait for the NSP resource to appear on boot nfp: wait for board state before talking to the NSP ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull more input updates from Dmitry Torokhov: "A second round of updates for the input subsystem: - a new driver for PWM-controlled vibrators - ucb1400 touchscreen driver had completely busted suspend/resume handling - we now handle "home" button found on some devices with Goodix touchscreens - assorted other fixups" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: i8042 - add Gigabyte P57 to the keyboard reset table Input: xpad - validate USB endpoint type during probe Input: ucb1400_ts - fix suspend and resume handling Input: edt-ft5x06 - fix access to non-existing register Input: elantech - make arrays debounce_packet static, reduces object code size Input: surface3_spi - make const array header static, reduces object code size Input: goodix - add support for capacitive home button Input: add a driver for PWM controllable vibrators Input: adi - make array seq static, reduces object code size
-
Markus Trippelsdorf authored
Commit 5620a0d1 ("firmware: delete in-kernel firmware") removed the entire firmware directory. Unfortunately it thereby also removed the support for built-in firmware. This restores the ability to build firmware directly into the kernel by pruning the original Makefile to the necessary minimum. The default for EXTRA_FIRMWARE_DIR is now the standard directory /lib/firmware/. Fixes: 5620a0d1 ("firmware: delete in-kernel firmware") Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de> Acked-by: Greg K-H <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Ido Schimmel authored
The driver doesn't support events from address families other than IPv4 and IPv6, so ignore them. Otherwise, we risk queueing a work item before it's initialized. This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES is enabled, as the VRF driver will try to add an l3mdev rule for the IPMR family. Fixes: 65e65ec1 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Andreas Rammhold <andreas@rammhold.de> Reported-by: Florian Klink <flokli@flokli.de> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pavel Machek authored
Fix link in filter.txt. Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Now skb->mstamp_skb is updated later, we also need to call tcp_rate_skb_sent() after the update is done. Fixes: 8c72c65b ("tcp: update skb->skb_mstamp more carefully") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds authored
Pull MIPS updates from Ralf Baechle: "This is the main pull request for 4.14 for MIPS; below a summary of the non-merge commits: CM: - Rename mips_cm_base to mips_gcr_base - Specify register size when generating accessors - Use BIT/GENMASK for register fields, order & drop shifts - Add cluster & block args to mips_cm_lock_other() CPC: - Use common CPS accessor generation macros - Use BIT/GENMASK for register fields, order & drop shifts - Introduce register modify (set/clear/change) accessors - Use change_*, set_* & clear_* where appropriate - Add CM/CPC 3.5 register definitions - Use GlobalNumber macros rather than magic numbers - Have asm/mips-cps.h include CM & CPC headers - Cluster support for topology functions - Detect CPUs in secondary clusters CPS: - Read GIC_VL_IDENT directly, not via irqchip driver DMA: - Consolidate coherent and non-coherent dma_alloc code - Don't use dma_cache_sync to implement fd_cacheflush FPU emulation / FP assist code: - Another series of 14 commits fixing corner cases such as NaN propgagation and other special input values. - Zero bits 32-63 of the result for a CLASS.D instruction. - Enhanced statics via debugfs - Do not use bools for arithmetic. GCC 7.1 moans about this. - Correct user fault_addr type Generic MIPS: - Enhancement of stack backtraces - Cleanup from non-existing options - Handle non word sized instructions when examining frame - Fix detection and decoding of ADDIUSP instruction - Fix decoding of SWSP16 instruction - Refactor handling of stack pointer in get_frame_info - Remove unreachable code from force_fcr31_sig() - Convert to using %pOF instead of full_name - Remove the R6000 support. - Move FP code from *_switch.S to *_fpu.S - Remove unused ST_OFF from r2300_switch.S - Allow platform to specify multiple its.S files - Add #includes to various files to ensure code builds reliable and without warning.. - Remove __invalidate_kernel_vmap_range - Remove plat_timer_setup - Declare various variables & functions static - Abstract CPU core & VP(E) ID access through accessor functions - Store core & VP IDs in GlobalNumber-style variable - Unify checks for sibling CPUs - Add CPU cluster number accessors - Prevent direct use of generic_defconfig - Make CONFIG_MIPS_MT_SMP default y - Add __ioread64_copy - Remove unnecessary inclusions of linux/irqchip/mips-gic.h GIC: - Introduce asm/mips-gic.h with accessor functions - Use new GIC accessor functions in mips-gic-timer - Remove counter access functions from irq-mips-gic.c - Remove gic_read_local_vp_id() from irq-mips-gic.c - Simplify shared interrupt pending/mask reads in irq-mips-gic.c - Simplify gic_local_irq_domain_map() in irq-mips-gic.c - Drop gic_(re)set_mask() functions in irq-mips-gic.c - Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(), gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c. - Convert remaining shared reg access, local int mask access and remaining local reg access to new accessors - Move GIC_LOCAL_INT_* to asm/mips-gic.h - Remove GIC_CPU_INT* macros from irq-mips-gic.c - Move various definitions to the driver - Remove gic_get_usm_range() - Remove __gic_irq_dispatch() forward declaration - Remove gic_init() - Use mips_gic_present() in place of gic_present and remove gic_present - Move gic_get_c0_*_int() to asm/mips-gic.h - Remove linux/irqchip/mips-gic.h - Inline __gic_init() - Inline gic_basic_init() - Make pcpu_masks a per-cpu variable - Use pcpu_masks to avoid reading GIC_SH_MASK* - Clean up mti, reserved-cpu-vectors handling - Use cpumask_first_and() in gic_set_affinity() - Let the core set struct irq_common_data affinity microMIPS: - Fix microMIPS stack unwinding on big endian systems MIPS-GIC: - SYNC after enabling GIC region NUMA: - Remove the unused parent_node() macro R6: - Constify r2_decoder_tables - Add accessor & bit definitions for GlobalNumber SMP: - Constify smp ops - Allow boot_secondary SMP op to return errors VDSO: - Drop gic_get_usm_range() usage - Avoid use of linux/irqchip/mips-gic.h Platform changes: Alchemy: - Add devboard machine type to cpuinfo - update cpu feature overrides - Threaded carddetect irqs for devboards AR7: - allow NULL clock for clk_get_rate BCM63xx: - Fix ENETDMA_6345_MAXBURST_REG offset - Allow NULL clock for clk_get_rate CI20: - Enable GPIO and RTC drivers in defconfig - Add ethernet and fixed-regulator nodes to DTS Generic platform: - Move Boston and NI 169445 FIT image source to their own files - Include asm/bootinfo.h for plat_fdt_relocated() - Include asm/time.h for get_c0_*_int() - Include asm/bootinfo.h for plat_fdt_relocated() - Include asm/time.h for get_c0_*_int() - Allow filtering enabled boards by requirements - Don't explicitly disable CONFIG_USB_SUPPORT - Bump default NR_CPUS to 16 JZ4700: - Probe the jz4740-rtc driver from devicetree Lantiq: - Drop check of boot select from the spi-falcon driver. - Drop check of boot select from the lantiq-flash MTD driver. - Access boot cause register in the watchdog driver through regmap - Add device tree binding documentation for the watchdog driver - Add docs for the RCU DT bindings. - Convert the fpi bus driver to a platform_driver - Remove ltq_reset_cause() and ltq_boot_select( - Switch to a proper reset driver - Switch to a new drivers/soc GPHY driver - Add an USB PHY driver for the Lantiq SoCs using the RCU module - Use of_platform_default_populate instead of __dt_register_buses - Enable MFD_SYSCON to be able to use it for the RCU MFD - Replace ltq_boot_select() with dummy implementation. Loongson 2F: - Allow NULL clock for clk_get_rate Malta: - Use new GIC accessor functions NI 169445: - Add support for NI 169445 board. - Only include in 32r2el kernels Octeon: - Add support for watchdog of 78XX SOCs. - Add support for watchdog of CN68XX SOCs. - Expose support for mips32r1, mips32r2 and mips64r1 - Enable more drivers in config file - Add support for accessing the boot vector. - Remove old boot vector code from watchdog driver - Define watchdog registers for 70xx, 73xx, 78xx, F75xx. - Make CSR functions node aware. - Allow access to CIU3 IRQ domains. - Misc cleanups in the watchdog driver Omega2+: - New board, add support and defconfig Pistachio: - Enable Root FS on NFS in defconfig Ralink: - Add Mediatek MT7628A SoC - Allow NULL clock for clk_get_rate - Explicitly request exclusive reset control in the pci-mt7620 PCI driver. SEAD3: - Only include in 32 bit kernels by default VoCore: - Add VoCore as a vendor t0 dt-bindings - Add defconfig file" * '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits) MIPS: Refactor handling of stack pointer in get_frame_info MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems MIPS: microMIPS: Fix decoding of swsp16 instruction MIPS: microMIPS: Fix decoding of addiusp instruction MIPS: microMIPS: Fix detection of addiusp instruction MIPS: Handle non word sized instructions when examining frame MIPS: ralink: allow NULL clock for clk_get_rate MIPS: Loongson 2F: allow NULL clock for clk_get_rate MIPS: BCM63XX: allow NULL clock for clk_get_rate MIPS: AR7: allow NULL clock for clk_get_rate MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset mips: Save all registers when saving the frame MIPS: Add DWARF unwinding to assembly MIPS: Make SAVE_SOME more standard MIPS: Fix issues in backtraces MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree MIPS: Ci20: Enable RTC driver watchdog: octeon-wdt: Add support for 78XX SOCs. watchdog: octeon-wdt: Add support for cn68XX SOCs. watchdog: octeon-wdt: File cleaning. ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pciLinus Torvalds authored
Pull PCI fix from Bjorn Helgaas: "Revert an attempt to fix a race while enabling upstream bridges because it broke iwlwifi firmware loading" * tag 'pci-v4.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: Revert "PCI: Avoid race while enabling upstream bridges"
-