- 23 Jul, 2020 2 commits
-
-
Douglas Anderson authored
When I have KASAN enabled on my kernel and I start stressing the touchscreen my system tends to hang. The touchscreen is one of the only things that does a lot of big i2c transfers and ends up hitting the DMA paths in the geni i2c driver. It appears that KASAN adds enough delay in my system to tickle a race condition in the DMA setup code. When the system hangs, I found that it was running the geni_i2c_irq() over and over again. It had these: m_stat = 0x04000080 rx_st = 0x30000011 dm_tx_st = 0x00000000 dm_rx_st = 0x00000000 dma = 0x00000001 Notably we're in DMA mode but are getting M_RX_IRQ_EN and M_RX_FIFO_WATERMARK_EN over and over again. Putting some traces in geni_i2c_rx_one_msg() showed that when we failed we were getting to the start of geni_i2c_rx_one_msg() but were never executing geni_se_rx_dma_prep(). I believe that the problem here is that we are starting the geni command before we run geni_se_rx_dma_prep(). If a transfer makes it far enough before we do that then we get into the state I have observed. Let's change the order, which seems to work fine. Although problems were seen on the RX path, code inspection suggests that the TX should be changed too. Change it as well. Fixes: 37692de5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller") Signed-off-by:
Douglas Anderson <dianders@chromium.org> Tested-by:
Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Reviewed-by:
Akash Asthana <akashast@codeaurora.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
Mukesh Kumar Savaliya <msavaliy@codeaurora.org> Signed-off-by:
Wolfram Sang <wsa@kernel.org>
-
Wolfram Sang authored
On R-Car Gen2, we get a timeout when reading from the address set in ICSAR, even though the slave interface is disabled. Clearing it fixes this situation. Note that Gen3 is not affected. To reproduce: bind and undbind an I2C slave on some bus, run 'i2cdetect' on that bus. Fixes: de20d185 ("i2c: rcar: add slave support") Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
Wolfram Sang <wsa@kernel.org>
-
- 22 Jul, 2020 4 commits
-
-
Ludovic Desroches authored
My colleague Codrin Ciubotariu, now, maintains this driver internally. Then I handover the mainline maintenance to him. Signed-off-by:
Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by:
Wolfram Sang <wsa@kernel.org>
-
Randy Dunlap authored
Drop the doubled word "be" in a comment. Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
Wolfram Sang <wsa@kernel.org>
-
Raviteja Narayanam authored
There are few issues on Zynq SOC observed in the stress tests causing timeout errors. Even though all the data is received, timeout error is thrown. This is due to an IP bug in which the COMP bit in ISR is not set at end of transfer and completion interrupt is not generated. This bug is seen on Zynq platforms when the following condition occurs: Master read & HOLD bit set & Transfer size register reaches '0'. One workaround is to clear the HOLD bit before the transfer size register reaches '0'. The current implementation checks for this at the start of the loop and also only for less than FIFO DEPTH case (ignoring the equal to case). So clear the HOLD bit when the data yet to receive is less than or equal to the FIFO DEPTH. This avoids the IP bug condition. Signed-off-by:
Raviteja Narayanam <raviteja.narayanam@xilinx.com> Acked-by:
Michal Simek <michal.simek@xilinx.com> Signed-off-by:
Wolfram Sang <wsa@kernel.org>
-
Raviteja Narayanam authored
This reverts commit d358def7. There are two issues with "i2c: cadence: Fix the hold bit setting" commit. 1. In case of combined message request from user space, when the HOLD bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent on the bus even before the last message is started. This is because when the HOLD bit is cleared, the FIFOS are empty and there is no pending transfer. The STOP condition should occur only after the last message is completed. 2. The code added by the commit is redundant. Driver is handling the setting/clearing of HOLD bit in right way before the commit. The setting of HOLD bit based on 'bus_hold_flag' is taken care in cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv functions. The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and cdns_i2c_recv functions based on bus_hold_flag and byte count. Since clearing of HOLD bit is done after the slave address is written to the register (writing to address register triggers the message transfer), it is ensured that STOP condition occurs at the right time after completion of the pending transfer (last message). Signed-off-by:
Raviteja Narayanam <raviteja.narayanam@xilinx.com> Acked-by:
Michal Simek <michal.simek@xilinx.com> Signed-off-by:
Wolfram Sang <wsa@kernel.org>
-
- 19 Jul, 2020 10 commits
-
-
Linus Torvalds authored
-
Linus Torvalds authored
Merge tag 'perf-tools-fixes-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into master Pull perf tooling fixes from Arnaldo Carvalho de Melo: - Update hashmap.h from libbpf and kvm.h from x86's kernel UAPI. - Set opt->set in libsubcmd's OPT_CALLBACK_SET(). This fixes 'perf record --switch-output-event event-name' usage" * tag 'perf-tools-fixes-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: tools arch kvm: Sync kvm headers with the kernel sources perf tools: Sync hashmap.h with libbpf's libsubcmd: Fix OPT_CALLBACK_SET()
-
Linus Torvalds authored
Merge tag 'x86-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master Pull x86 fixes from Thomas Gleixner: "A pile of fixes for x86: - Fix the I/O bitmap invalidation on XEN PV, which was overlooked in the recent ioperm/iopl rework. This caused the TSS and XEN's I/O bitmap to get out of sync. - Use the proper vectors for HYPERV. - Make disabling of stack protector for the entry code work with GCC builds which enable stack protector by default. Removing the option is not sufficient, it needs an explicit -fno-stack-protector to shut it off. - Mark check_user_regs() noinstr as it is called from noinstr code. The missing annotation causes it to be placed in the text section which makes it instrumentable. - Add the missing interrupt disable in exc_alignment_check() - Fixup a XEN_PV build dependency in the 32bit entry code - A few fixes to make the Clang integrated assembler happy - Move EFI stub build to the right place for out of tree builds - Make prepare_exit_to_usermode() static. It's not longer called from ASM code" * tag 'x86-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/boot: Don't add the EFI stub to targets x86/entry: Actually disable stack protector x86/ioperm: Fix io bitmap invalidation on Xen PV x86: math-emu: Fix up 'cmp' insn for clang ias x86/entry: Fix vectors to IDTENTRY_SYSVEC for CONFIG_HYPERV x86/entry: Add compatibility with IAS x86/entry/common: Make prepare_exit_to_usermode() static x86/entry: Mark check_user_regs() noinstr x86/traps: Disable interrupts in exc_aligment_check() x86/entry/32: Fix XEN_PV build dependency
-
Linus Torvalds authored
Merge tag 'timers-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master Pull timer fixes from Thomas Gleixner: "Two fixes for the timer wheel: - A timer which is already expired at enqueue time can set the base->next_expiry value backwards. As a consequence base->clk can be set back as well. This can lead to timers expiring early. Add a sanity check to prevent this. - When a timer is queued with an expiry time beyond the wheel capacity then it should be queued in the bucket of the last wheel level which is expiring last. The code adjusted the expiry time to the maximum wheel capacity, which is only correct when the wheel clock is 0. Aside of that the check whether the delta is larger than wheel capacity does not check the delta, it checks the expiry value itself. As a result timers can expire at random. Fix this by checking the right variable and adjust expiry time so it becomes base->clock plus capacity which places it into the outmost bucket in the last wheel level" * tag 'timers-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: timer: Fix wheel index calculation on last level timer: Prevent base->clk from moving backward
-
Linus Torvalds authored
Merge tag 'sched-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master Pull scheduler fixes from Thomas Gleixner: "A set of scheduler fixes: - Plug a load average accounting race which was introduced with a recent optimization casing load average to show bogus numbers. - Fix the rseq CPU id initialization for new tasks. sched_fork() does not update the rseq CPU id so the id is the stale id of the parent task, which can cause user space data corruption. - Handle a 0 return value of task_h_load() correctly in the load balancer, which does not decrease imbalance and therefore pulls until the maximum number of loops is reached, which might be all tasks just created by a fork bomb" * tag 'sched-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/fair: handle case of task_h_load() returning 0 sched: Fix unreliable rseq cpu_id for new tasks sched: Fix loadavg accounting race
-
Linus Torvalds authored
Merge tag 'irq-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master Pull irq fixes from Thomas Gleixner: "Two fixes for the interrupt subsystem: - Make the handling of the firmware node consistent and do not free the node after the domain has been created successfully. The core code stores a pointer to it which can lead to a use after free or double free. This used to "work" because the pointer was not stored when the initial code was written, but at some point later it was required to store it. Of course nobody noticed that the existing users break that way. - Handle affinity setting on inactive interrupts correctly when hierarchical irq domains are enabled. When interrupts are inactive with the modern hierarchical irqdomain design, the interrupt chips are not necessarily in a state where affinity changes can be handled. The legacy irq chip design allowed this because interrupts are immediately fully initialized at allocation time. X86 has a hacky workaround for this, but other implementations do not. This cased malfunction on GIC-V3. Instead of playing whack a mole to find all affected drivers, change the core code to store the requested affinity setting and then establish it when the interrupt is allocated, which makes the X86 hack go away" * tag 'irq-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq/affinity: Handle affinity setting on inactive interrupts correctly irqdomain/treewide: Keep firmware node unconditionally allocated
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usbLinus Torvalds authored
Pull USB fixes from Greg KH: "Here are a few small USB fixes, and one thunderbolt fix, for 5.8-rc6. Nothing huge in here, just the normal collection of gadget, dwc2/3, serial, and other minor USB driver fixes and id additions. Full details are in the shortlog. All of these have been in linux-next for a while with no reported issues" * tag 'usb-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: USB: serial: iuu_phoenix: fix memory corruption USB: c67x00: fix use after free in c67x00_giveback_urb usb: gadget: function: fix missing spinlock in f_uac1_legacy usb: gadget: udc: atmel: fix uninitialized read in debug printk usb: gadget: udc: atmel: remove outdated comment in usba_ep_disable() usb: dwc2: Fix shutdown callback in platform usb: cdns3: trace: fix some endian issues usb: cdns3: ep0: fix some endian issues usb: gadget: udc: gr_udc: fix memleak on error handling path in gr_ep_init() usb: gadget: fix langid kernel-doc warning in usbstring.c usb: dwc3: pci: add support for the Intel Jasper Lake usb: dwc3: pci: add support for the Intel Tiger Lake PCH -H variant usb: chipidea: core: add wakeup support for extcon USB: serial: option: add Quectel EG95 LTE modem thunderbolt: Fix path indices used in USB3 tunnel discovery USB: serial: ch341: add new Product ID for CH340 USB: serial: option: add GosunCn GM500 series USB: serial: cypress_m8: enable Simply Automated UPB PIM
-
git://git.infradead.org/users/hch/dma-mappingLinus Torvalds authored
Pull dma-mapping fixes from Christoph Hellwig: "Ensure we always have fully addressable memory in the dma coherent pool (Nicolas Saenz Julienne)" * tag 'dma-mapping-5.8-6' of git://git.infradead.org/users/hch/dma-mapping: dma-pool: do not allocate pool memory from CMA dma-pool: make sure atomic pool suits device dma-pool: introduce dma_guess_pool() dma-pool: get rid of dma_in_atomic_pool() dma-direct: provide function to check physical memory area validity
-
Arvind Sankar authored
vmlinux-objs-y is added to targets, which currently means that the EFI stub gets added to the targets as well. It shouldn't be added since it is built elsewhere. This confuses Makefile.build which interprets the EFI stub as a target $(obj)/$(objtree)/drivers/firmware/efi/libstub/lib.a and will create drivers/firmware/efi/libstub/ underneath arch/x86/boot/compressed, to hold this supposed target, if building out-of-tree. [0] Fix this by pulling the stub out of vmlinux-objs-y into efi-obj-y. [0] See scripts/Makefile.build near the end: # Create directories for object files if they do not exist Signed-off-by:
Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Masahiro Yamada <masahiroy@kernel.org> Acked-by:
Ard Biesheuvel <ardb@kernel.org> Link: https://lkml.kernel.org/r/20200715032631.1562882-1-nivedita@alum.mit.edu
-
Kees Cook authored
Some builds of GCC enable stack protector by default. Simply removing the arguments is not sufficient to disable stack protector, as the stack protector for those GCC builds must be explicitly disabled. Remove the argument removals and add -fno-stack-protector. Additionally include missed x32 argument updates, and adjust whitespace for readability. Fixes: 20355e5f ("x86/entry: Exclude low level entry code from sanitizing") Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/202006261333.585319CA6B@keescook
-
- 18 Jul, 2020 6 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull SCSI fix from James Bottomley: "One small driver fix. Although the one liner makes it sound like a cosmetic change, it's a regression fix for the megaraid_sas driver" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: megaraid_sas: Remove undefined ENABLE_IRQ_POLL macro
-
Linus Torvalds authored
Merge tag 'hwmon-for-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging into master Pull hwmon fixes from Guenter Roeck: - Using SCT on some Tohsiba drives causes firmware hangs. Disable its use in the drivetemp driver. - Handle potential buffer overflows in scmi and aspeed-pwm-tacho driver. - Energy reporting does not work well on all AMD CPUs. Restrict amd_energy to known working models. - Enable reading the CPU temperature on NCT6798D using undocumented registers. - Fix read errors seen if PEC is enabled in adm1275 driver. - Fix setting the pwm1_enable in emc2103 driver. * tag 'hwmon-for-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: (drivetemp) Avoid SCT usage on Toshiba DT01ACA family drives hwmon: (scmi) Fix potential buffer overflow in scmi_hwmon_probe() hwmon: (nct6775) Accept PECI Calibration as temperature source for NCT6798D hwmon: (adm1275) Make sure we are reading enough data for different chips hwmon: (emc2103) fix unable to change fan pwm1_enable attribute hwmon: (amd_energy) match for supported models hwmon: (aspeed-pwm-tacho) Avoid possible buffer overflow
-
Linus Torvalds authored
Merge tag 'riscv-for-linus-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux into master Pull RISC-V fixes from Palmer Dabbelt: "Two fixes: - 16KiB kernel stacks on rv64, which fixes a lot of crashes. - Rolling an mmiowb() into the scheduler, which when combined with Will's fix to the mmiowb()-on-spinlock should fix the PREEMPT issues we've been seeing" * tag 'riscv-for-linus-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: RISC-V: Upgrade smp_mb__after_spinlock() to iorw,iorw riscv: use 16KB kernel stack on 64-bit
-
Linus Torvalds authored
Merge tag 'powerpc-5.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux into master Pull powerpc fixes from Michael Ellerman: "Some more powerpc fixes for 5.8: - A fix to the VAS code we merged this cycle, to report the proper error code to userspace for address translation failures. And a selftest update to match. - Another fix for our pkey handling of PROT_EXEC mappings. - A fix for a crash when booting a "secure VM" under an ultravisor with certain numbers of CPUs. Thanks to: Aneesh Kumar K.V, Haren Myneni, Laurent Dufour, Sandipan Das, Satheesh Rajendran, Thiago Jung Bauermann" * tag 'powerpc-5.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: selftests/powerpc: Use proper error code to check fault address powerpc/vas: Report proper error code for address translation failure powerpc/pseries/svm: Fix incorrect check for shared_lppaca_size powerpc/book3s64/pkeys: Fix pkey_access_permitted() for execute disable pkey
-
Maciej S. Szmigiero authored
It has been observed that Toshiba DT01ACA family drives have WRITE FPDMA QUEUED command timeouts and sometimes just freeze until power-cycled under heavy write loads when their temperature is getting polled in SCT mode. The SMART mode seems to be fine, though. Let's make sure we don't use SCT mode for these drives then. While only the 3 TB model was actually caught exhibiting the problem let's play safe here to avoid data corruption and extend the ban to the whole family. Fixes: 5b46903d ("hwmon: Driver for disk and solid state drives with temperature sensors") Cc: stable@vger.kernel.org Signed-off-by:
Maciej S. Szmigiero <mail@maciej.szmigiero.name> Link: https://lore.kernel.org/r/0cb2e7022b66c6d21d3f189a12a97878d0e7511b.1595075458.git.mail@maciej.szmigiero.nameSigned-off-by:
Guenter Roeck <linux@roeck-us.net>
-
Andy Lutomirski authored
tss_invalidate_io_bitmap() wasn't wired up properly through the pvop machinery, so the TSS and Xen's io bitmap would get out of sync whenever disabling a valid io bitmap. Add a new pvop for tss_invalidate_io_bitmap() to fix it. This is XSA-329. Fixes: 22fe5b04 ("x86/ioperm: Move TSS bitmap update to exit to user work") Signed-off-by:
Andy Lutomirski <luto@kernel.org> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Juergen Gross <jgross@suse.com> Reviewed-by:
Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/d53075590e1f91c19f8af705059d3ff99424c020.1595030016.git.luto@kernel.org
-
- 17 Jul, 2020 18 commits
-
-
git://git.linux-nfs.org/projects/anna/linux-nfsLinus Torvalds authored
Pull NFS client fixes from Anna Schumaker: "A few more NFS client bugfixes for Linux 5.8: NFS: - Fix interrupted slots by using the SEQUENCE operation SUNRPC: - revert d03727b2 to fix unkillable IOs xprtrdma: - Fix double-free in rpcrdma_ep_create() - Fix recursion into rpcrdma_xprt_disconnect() - Fix return code from rpcrdma_xprt_connect() - Fix handling of connect errors - Fix incorrect header size calculations" * tag 'nfs-for-5.8-3' of git://git.linux-nfs.org/projects/anna/linux-nfs: SUNRPC reverting d03727b2 ("NFSv4 fix CLOSE not waiting for direct IO compeletion") xprtrdma: fix incorrect header size calculations NFS: Fix interrupted slots by sending a solo SEQUENCE operation xprtrdma: Fix handling of connect errors xprtrdma: Fix return code from rpcrdma_xprt_connect() xprtrdma: Fix recursion into rpcrdma_xprt_disconnect() xprtrdma: Fix double-free in rpcrdma_ep_create()
-
git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds authored
Pull ARM SoC fixes from Arnd Bergmann: "This time there are a number of actual code fixes, plus a small set of device tree issues getting addressed: Renesas: - one defconfig cleanup to allow a later Kconfig change Intel socfpga: - enable QSPI devices on some machines - fix DTC validation warnings TI OMAP: - Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module driver - A regression fix for ti-sysc no-idle handling that caused issues compared to earlier platform data based booting - A fix for memory leak for omap_hwmod_allocate_module - Fix d_can driver probe for am437x NXP i.MX: - A couple of fixes on i.MX platform device registration code to stop the use of invalid IRQ 0. - Fix a regression seen on ls1021a platform, caused by commit 52102a3b ("soc: imx: move cpu code to drivers/soc/imx"). - Fix a misconfiguration of audio SSI on imx6qdl-gw551x board. Amlogic Meson: - misc DT fixes - SoC ID fixes to detect all chips correctly" * tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema arm64: dts: stratix10: increase QSPI reg address in nand dts file arm64: dts: stratix10: add status to qspi dts node arm64: dts: agilex: add status to qspi dts node ARM: dts: Fix dcan driver probe failed on am437x platform ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST soc: imx: check ls1021a ARM: imx: Remove imx_add_imx_dma() unused irq_err argument ARM: imx: Provide correct number of resources when registering gpio devices ARM: dts: imx6qdl-gw551x: fix audio SSI bus: ti-sysc: Do not disable on suspend for no-idle bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk bus: ti-sysc: Fix wakeirq sleeping function called from invalid context ARM: dts: meson: Align L2 cache-controller nodename with dtschema arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency arm64: dts: meson: add missing gxl rng clock soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linuxLinus Torvalds authored
Pull arm64 fixes from Will Deacon: "A batch of arm64 fixes. Although the diffstat is a bit larger than we'd usually have at this stage, a decent amount of it is the addition of comments describing our syscall tracing behaviour, and also a sweep across all the modular arm64 PMU drivers to make them rebust against unloading and unbinding. There are a couple of minor things kicking around at the moment (CPU errata and module PLTs for very large modules), but I'm not expecting any significant changes now for us in 5.8. - Fix kernel text addresses for relocatable images booting using EFI and with KASLR disabled so that they match the vmlinux ELF binary. - Fix unloading and unbinding of PMU driver modules. - Fix generic mmiowb() when writeX() is called from preemptible context (reported by the riscv folks). - Fix ptrace hardware single-step interactions with signal handlers, system calls and reverse debugging. - Fix reporting of 64-bit x0 register for 32-bit tasks via 'perf_regs'. - Add comments describing syscall entry/exit tracing ABI" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: drivers/perf: Prevent forced unbinding of PMU drivers asm-generic/mmiowb: Allow mmiowb_set_pending() when preemptible() arm64: Use test_tsk_thread_flag() for checking TIF_SINGLESTEP arm64: ptrace: Use NO_SYSCALL instead of -1 in syscall_trace_enter() arm64: syscall: Expand the comment about ptrace and syscall(-1) arm64: ptrace: Add a comment describing our syscall entry/exit trap ABI arm64: compat: Ensure upper 32 bits of x0 are zero on syscall return arm64: ptrace: Override SPSR.SS when single-stepping is enabled arm64: ptrace: Consistently use pseudo-singlestep exceptions drivers/perf: Fix kernel panic when rmmod PMU modules during perf sampling efi/libstub/arm64: Retain 2MB kernel Image alignment if !KASLR
-
Thomas Gleixner authored
Setting interrupt affinity on inactive interrupts is inconsistent when hierarchical irq domains are enabled. The core code should just store the affinity and not call into the irq chip driver for inactive interrupts because the chip drivers may not be in a state to handle such requests. X86 has a hacky workaround for that but all other irq chips have not which causes problems e.g. on GIC V3 ITS. Instead of adding more ugly hacks all over the place, solve the problem in the core code. If the affinity is set on an inactive interrupt then: - Store it in the irq descriptors affinity mask - Update the effective affinity to reflect that so user space has a consistent view - Don't call into the irq chip driver This is the core equivalent of the X86 workaround and works correctly because the affinity setting is established in the irq chip when the interrupt is activated later on. Note, that this is only effective when hierarchical irq domains are enabled by the architecture. Doing it unconditionally would break legacy irq chip implementations. For hierarchial irq domains this works correctly as none of the drivers can have a dependency on affinity setting in inactive state by design. Remove the X86 workaround as it is not longer required. Fixes: 02edee15 ("x86/apic/vector: Ignore set_affinity call for inactive interrupts") Reported-by:
Ali Saidi <alisaidi@amazon.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Tested-by:
Ali Saidi <alisaidi@amazon.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200529015501.15771-1-alisaidi@amazon.com Link: https://lkml.kernel.org/r/877dv2rv25.fsf@nanos.tec.linutronix.de
-
Frederic Weisbecker authored
When an expiration delta falls into the last level of the wheel, that delta has be compared against the maximum possible delay and reduced to fit in if necessary. However instead of comparing the delta against the maximum, the code compares the actual expiry against the maximum. Then instead of fixing the delta to fit in, it sets the maximum delta as the expiry value. This can result in various undesired outcomes, the worst possible one being a timer expiring 15 days ahead to fire immediately. Fixes: 500462a9 ("timers: Switch to a non-cascading wheel") Signed-off-by:
Frederic Weisbecker <frederic@kernel.org> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20200717140551.29076-2-frederic@kernel.org
-
Olga Kornievskaia authored
Reverting commit d03727b2 "NFSv4 fix CLOSE not waiting for direct IO compeletion". This patch made it so that fput() by calling inode_dio_done() in nfs_file_release() would wait uninterruptably for any outstanding directIO to the file (but that wait on IO should be killable). The problem the patch was also trying to address was REMOVE returning ERR_ACCESS because the file is still opened, is supposed to be resolved by server returning ERR_FILE_OPEN and not ERR_ACCESS. Signed-off-by:
Olga Kornievskaia <kolga@netapp.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com>
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull io_uring fix from Jens Axboe: "Fix for a case where, with automatic buffer selection, we can leak the buffer descriptor for recvmsg" * tag 'io_uring-5.8-2020-07-17' of git://git.kernel.dk/linux-block: io_uring: fix recvmsg memory leak with buffer selection
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull block fix from Jens Axboe: "Single NVMe multipath capacity fix" * tag 'block-5.8-2020-07-17' of git://git.kernel.dk/linux-block: nvme: explicitly update mpath disk capacity on revalidation
-
Linus Torvalds authored
Merge tag 'fuse-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse into master Pull fuse fixes from Miklos Szeredi: - two regressions in this cycle caused by the conversion of writepage list to an rb_tree - two regressions in v5.4 cause by the conversion to the new mount API - saner behavior of fsconfig(2) for the reconfigure case - an ancient issue with FS_IOC_{GET,SET}FLAGS ioctls * tag 'fuse-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse: fuse: Fix parameter for FS_IOC_{GET,SET}FLAGS fuse: don't ignore errors from fuse_writepages_fill() fuse: clean up condition for writepage sending fuse: reject options on reconfigure via fsconfig(2) fuse: ignore 'data' argument of mount(..., MS_REMOUNT) fuse: use ->reconfigure() instead of ->remount_fs() fuse: fix warning in tree_insert() and clean up writepage insertion fuse: move rb_erase() before tree_insert()
-
Linus Torvalds authored
Merge tag 'ovl-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs into master Pull overlayfs fixes from Miklos Szeredi: - fix a regression introduced in v4.20 in handling a regenerated squashfs lower layer - two regression fixes for this cycle, one of which is Oops inducing - miscellaneous issues * tag 'ovl-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs: ovl: fix lookup of indexed hardlinks with metacopy ovl: fix unneeded call to ovl_change_flags() ovl: fix mount option checks for nfs_export with no upperdir ovl: force read-only sb on failure to create index dir ovl: fix regression with re-formatted lower squashfs ovl: fix oops in ovl_indexdir_cleanup() with nfs_export=on ovl: relax WARN_ON() when decoding lower directory file handle ovl: remove not used argument in ovl_check_origin ovl: change ovl_copy_up_flags static ovl: inode reference leak in ovl_is_inuse true case.
-
Linus Torvalds authored
Merge tag 'spi-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into master Pull spi fixes from Mark Brown: "A couple of small driver specific fixes for fairly minor issues" * tag 'spi-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: spi: spi-sun6i: sun6i_spi_transfer_one(): fix setting of clock rate spi: mediatek: use correct SPI_CFG2_REG MACRO
-
Linus Torvalds authored
Merge tag 'regulator-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into master Pull regulator fixes from Mark Brown: "The more substantial fix here is the rename of the da903x driver which fixes a collision with the parent MFD driver name which caused issues when things were built as modules. There's also a fix for a mislableled regulator on the pmi8994 which is quite important for systems with that device" * tag 'regulator-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: MAINTAINERS: remove obsolete entry after file renaming regulator: rename da903x to da903x-regulator regulator: qcom_smd: Fix pmi8994 label
-
Linus Torvalds authored
Merge tag 'regmap-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into master Pull regmap fixes from Mark Brown: "A couple of substantial fixes here, one from Doug which fixes the debugfs code for MMIO regmaps (fortunately not the common case) and one from Marc fixing lookups of multiple regmaps for the same device (a very unusual case). There's also a fix for Kconfig to ensure we enable SoundWire properly" * tag 'regmap-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: regmap: debugfs: Don't sleep while atomic for fast_io regmaps regmap: add missing dependency on SoundWire regmap: dev_get_regmap_match(): fix string comparison
-
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hidLinus Torvalds authored
Pull HID fixes from Jiri Kosina: - linked list race condition fix in hid-steam driver from Rodrigo Rivas Costa - assorted deviceID-specific quirks and other small cosmetic cleanups * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: HID: logitech-hidpp: avoid repeated "multiplier = " log messages HID: logitech: Use HIDPP_RECEIVER_INDEX instead of 0xff HID: quirks: Ignore Simply Automated UPB PIM HID: apple: Disable Fn-key key-re-mapping on clone keyboards MAINTAINERS: update uhid and hid-wiimote entry HID: steam: fixes race in handling device list. HID: magicmouse: do not set up autorepeat HID: alps: support devices with report id 2 HID: quirks: Always poll Obins Anne Pro 2 keyboard HID: i2c-hid: add Mediacom FlexBook edge13 to descriptor override
-
Palmer Dabbelt authored
While digging through the recent mmiowb preemption issue it came up that we aren't actually preventing IO from crossing a scheduling boundary. While it's a bit ugly to overload smp_mb__after_spinlock() with this behavior, it's what PowerPC is doing so there's some precedent. Signed-off-by:
Palmer Dabbelt <palmerdabbelt@google.com>
-
Arnd Bergmann authored
Merge tag 'socfpga_fixes_for_v5.8_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes arm/arm64: dts: socfpga: fixes for v5.8 - Add status = "okay" in QSPI - Increase QSPI size in reg property - Fix dtschema for SoCFPGA platforms * tag 'socfpga_fixes_for_v5.8_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema arm64: dts: stratix10: increase QSPI reg address in nand dts file arm64: dts: stratix10: add status to qspi dts node arm64: dts: agilex: add status to qspi dts node Link: https://lore.kernel.org/r/20200717155758.18233-1-dinguyen@kernel.orgSigned-off-by:
Arnd Bergmann <arnd@arndb.de>
-
Arnd Bergmann authored
Merge tag 'renesas-fixes-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes Renesas fixes for v5.8 - Replace CONFIG_PCIE_RCAR by CONFIG_PCIE_RCAR_HOST in the defconfig, to unblock a planned Kconfig change. * tag 'renesas-fixes-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST Link: https://lore.kernel.org/r/20200717100523.15418-1-geert+renesas@glider.beSigned-off-by:
Arnd Bergmann <arnd@arndb.de>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/soundLinus Torvalds authored
Pull sound fixes from Takashi Iwai: "No surprise here, just a few device-specific small fixes: two fixes for USB LINE6 and one for USB-audio drivers wrt syzkaller fuzzer issues, while the rest are all HD-audio Realtek quirks" * tag 'sound-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: hda/realtek - fixup for yet another Intel reference board ALSA: hda/realtek - Enable Speaker for ASUS UX563 ALSA: hda/realtek - Enable Speaker for ASUS UX533 and UX534 ALSA: hda/realtek: Enable headset mic of Acer TravelMate B311R-31 with ALC256 ALSA: hda/realtek: enable headset mic of ASUS ROG Zephyrus G14(G401) series with ALC289 ALSA: hda/realtek - change to suitable link model for ASUS platform ALSA: usb-audio: Fix race against the error recovery URB submission ALSA: line6: Sync the pending work cancel at disconnection ALSA: line6: Perform sanity check for each URB creation
-