[ Upstream commit 3e3380d0 ]

Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have leading "0x"

and

Warning (unit_address_format): Node /XXX unit name should not have leading 0s

Converted using the following command:

find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +

For simplicity, two sed expressions were used to solve each warnings
separately.

To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the opening curly brace:

https://elinux.org/Device_Tree_Linux#Linux_conventions

This will solve as a side effect warning:

Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"

This is a follow up to commit 4c9847b7 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[vzapolskiy: fixed commit message to pass checkpatch.pl test]
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5de0fef0 ]

The EFI memory attributes code cross-references the EFI memory map with
the more granular EFI memory attributes table to ensure that they are in
sync before applying the strict permissions to the regions it describes.

Since we always install virtual mappings for the EFI runtime regions to
which these strict permissions apply, we currently perform a sanity check
on the EFI memory descriptor, and ensure that the EFI_MEMORY_RUNTIME bit
is set, and that the virtual address has been assigned.

However, in cases where a runtime region exists at physical address 0x0,
and the virtual mapping equals the physical mapping, e.g., when running
in mixed mode on x86, we encounter a memory descriptor with the runtime
attribute and virtual address 0x0, and incorrectly draw the conclusion
that a runtime region exists for which no virtual mapping was installed,
and give up altogether. The consequence of this is that firmware mappings
retain their read-write-execute permissions, making the system more
vulnerable to attacks.

So let's only bail if the virtual address of 0x0 has been assigned to a
physical region that does not reside at address 0x0.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 10f0d2f5 ("efi: Implement generic support for the Memory ...")
Link: http://lkml.kernel.org/r/20190202094119.13230-4-ard.biesheuvel@linaro.orgSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 11907e9d ]

The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: Wen Yang <yellowriver2010@hotmil.com>
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0f9e980b ]

I'm seeing series of e1000e resets (sometimes endless) at system boot
if something generates tx traffic at this time. In my case this is
netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states
have been disabled in order to enable jumbo frames" from e1000e itself.
As result e1000_watchdog_task sees used tx buffer while carrier is off
and start this reset cycle again.

[   17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[   17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000
[   23.033336] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[   27.174495] 8021q: 802.1Q VLAN Support v1.8
[   27.174513] 8021q: adding VLAN 0 to HW filter on device eth1
[   30.671724] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
[   30.898564] netpoll: netconsole: local port 6666
[   30.898566] netpoll: netconsole: local IPv6 address 2a02:6b8:0:80b:beae:c5ff:fe28:23f8
[   30.898567] netpoll: netconsole: interface 'eth1'
[   30.898568] netpoll: netconsole: remote port 6666
[   30.898568] netpoll: netconsole: remote IPv6 address 2a02:6b8:b000:605c:e61d:2dff:fe03:3790
[   30.898569] netpoll: netconsole: remote ethernet address b0:a8:6e:f4:ff:c0
[   30.917747] console [netcon0] enabled
[   30.917749] netconsole: network logging started
[   31.453353] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.185730] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.321840] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.465822] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.597423] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.745417] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   34.877356] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.005441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.157376] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.289362] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   35.417441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[   37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None

This patch flushes tx buffers only once when carrier is off
rather than at each watchdog iteration.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f25191bb ]

The following traceback is sometimes seen when booting an image in qemu:

[   54.608293] cdrom: Uniform CD-ROM driver Revision: 3.20
[   54.611085] Fusion MPT base driver 3.04.20
[   54.611877] Copyright (c) 1999-2008 LSI Corporation
[   54.616234] Fusion MPT SAS Host driver 3.04.20
[   54.635139] sysctl duplicate entry: /dev/cdrom//info
[   54.639578] CPU: 0 PID: 266 Comm: kworker/u4:5 Not tainted 5.0.0-rc5 #1
[   54.639578] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
[   54.641273] Workqueue: events_unbound async_run_entry_fn
[   54.641273] Call Trace:
[   54.641273]  dump_stack+0x67/0x90
[   54.641273]  __register_sysctl_table+0x50b/0x570
[   54.641273]  ? rcu_read_lock_sched_held+0x6f/0x80
[   54.641273]  ? kmem_cache_alloc_trace+0x1c7/0x1f0
[   54.646814]  __register_sysctl_paths+0x1c8/0x1f0
[   54.646814]  cdrom_sysctl_register.part.7+0xc/0x5f
[   54.646814]  register_cdrom.cold.24+0x2a/0x33
[   54.646814]  sr_probe+0x4bd/0x580
[   54.646814]  ? __driver_attach+0xd0/0xd0
[   54.646814]  really_probe+0xd6/0x260
[   54.646814]  ? __driver_attach+0xd0/0xd0
[   54.646814]  driver_probe_device+0x4a/0xb0
[   54.646814]  ? __driver_attach+0xd0/0xd0
[   54.646814]  bus_for_each_drv+0x73/0xc0
[   54.646814]  __device_attach+0xd6/0x130
[   54.646814]  bus_probe_device+0x9a/0xb0
[   54.646814]  device_add+0x40c/0x670
[   54.646814]  ? __pm_runtime_resume+0x4f/0x80
[   54.646814]  scsi_sysfs_add_sdev+0x81/0x290
[   54.646814]  scsi_probe_and_add_lun+0x888/0xc00
[   54.646814]  ? scsi_autopm_get_host+0x21/0x40
[   54.646814]  __scsi_add_device+0x116/0x130
[   54.646814]  ata_scsi_scan_host+0x93/0x1c0
[   54.646814]  async_run_entry_fn+0x34/0x100
[   54.646814]  process_one_work+0x237/0x5e0
[   54.646814]  worker_thread+0x37/0x380
[   54.646814]  ? rescuer_thread+0x360/0x360
[   54.646814]  kthread+0x118/0x130
[   54.646814]  ? kthread_create_on_node+0x60/0x60
[   54.646814]  ret_from_fork+0x3a/0x50

The only sensible explanation is that cdrom_sysctl_register() is called
twice, once from the module init function and once from register_cdrom().
cdrom_sysctl_register() is not mutex protected and may happily execute
twice if the second call is made before the first call is complete.

Use a static atomic to ensure that the function is executed exactly once.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a5399db1 ]

There is no clipping on the x or y axis for logos larger that the framebuffer
size. Therefore: a logo bigger than screen size leads to invalid memory access:

[    1.254664] Backtrace:
[    1.254728] [<c02714e0>] (cfb_imageblit) from [<c026184c>] (fb_show_logo+0x620/0x684)
[    1.254763]  r10:00000003 r9:00027fd8 r8:c6a40000 r7:c6a36e50 r6:00000000 r5:c06b81e4
[    1.254774]  r4:c6a3e800
[    1.254810] [<c026122c>] (fb_show_logo) from [<c026c1e4>] (fbcon_switch+0x3fc/0x46c)
[    1.254842]  r10:c6a3e824 r9:c6a3e800 r8:00000000 r7:c6a0c000 r6:c070b014 r5:c6a3e800
[    1.254852]  r4:c6808c00
[    1.254889] [<c026bde8>] (fbcon_switch) from [<c029c8f8>] (redraw_screen+0xf0/0x1e8)
[    1.254918]  r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:c070d5a0 r5:00000080
[    1.254928]  r4:c6808c00
[    1.254961] [<c029c808>] (redraw_screen) from [<c029d264>] (do_bind_con_driver+0x194/0x2e4)
[    1.254991]  r9:00000000 r8:00000000 r7:00000014 r6:c070d5a0 r5:c070d5a0 r4:c070d5a0

So prevent displaying a logo bigger than screen size and avoid invalid
memory access.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f368ff18 ]

When an application aborts the connection by moving QP from RTS to ERROR,
then iw_cxgb4's modify_rc_qp() RTS->ERROR logic sets the
*srqidxp to 0 via t4_set_wq_in_error(&qhp->wq, 0), and aborts the
connection by calling c4iw_ep_disconnect().

c4iw_ep_disconnect() does the following:
 1. sends up a close_complete_upcall(ep, -ECONNRESET) to libcxgb4.
 2. sends abort request CPL to hw.

But, since the close_complete_upcall() is sent before sending the
ABORT_REQ to hw, libcxgb4 would fail to release the srqidx if the
connection holds one. Because, the srqidx is passed up to libcxgb4 only
after corresponding ABORT_RPL is processed by kernel in abort_rpl().

This patch handle the corner-case by moving the call to
close_complete_upcall() from c4iw_ep_disconnect() to abort_rpl().  So that
libcxgb4 is notified about the -ECONNRESET only after abort_rpl(), and
libcxgb4 can relinquish the srqidx properly.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1136b072 ]

Waiman reported that on large systems with a large amount of interrupts the
readout of /proc/stat takes a long time to sum up the interrupt
statistics. In principle this is not a problem. but for unknown reasons
some enterprise quality software reads /proc/stat with a high frequency.

The reason for this is that interrupt statistics are accounted per cpu. So
the /proc/stat logic has to sum up the interrupt stats for each interrupt.

This can be largely avoided for interrupts which are not marked as
'PER_CPU' interrupts by simply adding a per interrupt summation counter
which is incremented along with the per interrupt per cpu counter.

The PER_CPU interrupts need to avoid that and use only per cpu accounting
because they share the interrupt number and the interrupt descriptor and
concurrent updates would conflict or require unwanted synchronization.
Reported-by: Waiman Long <longman@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Waiman Long <longman@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Daniel Colascione <dancol@google.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Link: https://lkml.kernel.org/r/20190208135020.925487496@linutronix.de

8<-------------

v2: Undo the unintentional layout change of struct irq_desc.

 include/linux/irqdesc.h |    1 +
 kernel/irq/chip.c       |   12 ++++++++++--
 kernel/irq/internals.h  |    8 +++++++-
 kernel/irq/irqdesc.c    |    7 ++++++-
 4 files changed, 24 insertions(+), 4 deletions(-)
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 596b5a5d ]

Currently sysfs_strtoul_clamp() is defined as,
 82 #define sysfs_strtoul_clamp(file, var, min, max)                   \
 83 do {                                                               \
 84         if (attr == &sysfs_ ## file)                               \
 85                 return strtoul_safe_clamp(buf, var, min, max)      \
 86                         ?: (ssize_t) size;                         \
 87 } while (0)

The problem is, if bit width of var is less then unsigned long, min and
max may not protect var from integer overflow, because overflow happens
in strtoul_safe_clamp() before checking min and max.

To fix such overflow in sysfs_strtoul_clamp(), to make min and max take
effect, this patch adds an unsigned long variable, and uses it to macro
strtoul_safe_clamp() to convert an unsigned long value in range defined
by [min, max]. Then assign this value to var. By this method, if bit
width of var is less than unsigned long, integer overflow won't happen
before min and max are checking.

Now sysfs_strtoul_clamp() can properly handle smaller data type like
unsigned int, of cause min and max should be defined in range of
unsigned int too.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8c27a395 ]

People may set sequential_cutoff of a cached device via sysfs file,
but current code does not check input value overflow. E.g. if value
4294967295 (UINT_MAX) is written to file sequential_cutoff, its value
is 4GB, but if 4294967296 (UINT_MAX + 1) is written into, its value
will be 0. This is an unexpected behavior.

This patch replaces d_strtoi_h() by sysfs_strtoul_clamp() to convert
input string to unsigned integer value, and limit its range in
[0, UINT_MAX]. Then the input overflow can be fixed.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a91fbda4 ]

Cache set sysfs entry io_error_halflife is used to set c->error_decay.
c->error_decay is in type unsigned int, and it is converted by
strtoul_or_return(), therefore overflow to c->error_decay is possible
for a large input value.

This patch fixes the overflow by using strtoul_safe_clamp() to convert
input string to an unsigned long value in range [0, UINT_MAX], then
divides by 88 and set it to c->error_decay.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 54f64d5c ]

Since the 5.0 merge window opened, I've been seeing frequent
crashes on suspend and reboot with the trace:

[   36.911170] Unable to handle kernel paging request at virtual address ffffff801153d660
[   36.912769] Unable to handle kernel paging request at virtual address ffffff800004b564
...
[   36.950666] Call trace:
[   36.950670]  queued_spin_lock_slowpath+0x1cc/0x2c8
[   36.950681]  _raw_spin_lock_irqsave+0x64/0x78
[   36.950692]  complete+0x28/0x70
[   36.950703]  ffs_epfile_io_complete+0x3c/0x50
[   36.950713]  usb_gadget_giveback_request+0x34/0x108
[   36.950721]  dwc3_gadget_giveback+0x50/0x68
[   36.950723]  dwc3_thread_interrupt+0x358/0x1488
[   36.950731]  irq_thread_fn+0x30/0x88
[   36.950734]  irq_thread+0x114/0x1b0
[   36.950739]  kthread+0x104/0x130
[   36.950747]  ret_from_fork+0x10/0x1c

I isolated this down to in ffs_epfile_io():
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/usb/gadget/function/f_fs.c#n1065

Where the completion done is setup on the stack:
  DECLARE_COMPLETION_ONSTACK(done);

Then later we setup a request and queue it, and wait for it:
  if (unlikely(wait_for_completion_interruptible(&done))) {
    /*
    * To avoid race condition with ffs_epfile_io_complete,
    * dequeue the request first then check
    * status. usb_ep_dequeue API should guarantee no race
    * condition with req->complete callback.
    */
    usb_ep_dequeue(ep->ep, req);
    interrupted = ep->status < 0;
  }

The problem is, that we end up being interrupted, dequeue the
request, and exit.

But then the irq triggers and we try calling complete() on the
context pointer which points to now random stack space, which
results in the panic.

Alan Stern pointed out there is a bug here, in that the snippet
above "assumes that usb_ep_dequeue() waits until the request has
been completed." And that:

    wait_for_completion(&done);

Is needed right after the usb_ep_dequeue().

Thus this patch implements that change. With it I no longer see
the crashes on suspend or reboot.

This issue seems to have been uncovered by behavioral changes in
the dwc3 driver in commit fec9095b ("usb: dwc3: gadget:
remove wait_end_transfer").

Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Zeng Tao <prime.zeng@hisilicon.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Thinh Nguyen <thinh.nguyen@synopsys.com>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Jerry Zhang <zhangjerry@google.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Vincent Pelletier <plr.vincent@gmail.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d9c0b2af ]

BE dai links only have internal PCM's and their substream ops may
not be set. Suspending these PCM's will result in their
 ops->trigger() being invoked and cause a kernel oops.
So skip suspending PCM's if their ops are NULL.

[ NOTE: this change is required now for following the recent PCM core
  change to get rid of snd_pcm_suspend() call.  Since DPCM BE takes
  the runtime carried from FE while keeping NULL ops, it can hit this
  bug.  See details at:
     https://github.com/thesofproject/linux/pull/582
  -- tiwai ]
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit de9c0d49 ]

While building arm32 allyesconfig, I ran into the following errors:

  arch/arm/lib/xor-neon.c:17:2: error: You should compile this file with
  '-mfloat-abi=softfp -mfpu=neon'

  In file included from lib/raid6/neon1.c:27:
  /home/nathan/cbl/prebuilt/lib/clang/8.0.0/include/arm_neon.h:28:2:
  error: "NEON support not enabled"

Building V=1 showed NEON_FLAGS getting passed along to Clang but
__ARM_NEON__ was not getting defined. Ultimately, it boils down to Clang
only defining __ARM_NEON__ when targeting armv7, rather than armv6k,
which is the '-march' value for allyesconfig.

>From lib/Basic/Targets/ARM.cpp in the Clang source:

  // This only gets set when Neon instructions are actually available, unlike
  // the VFP define, hence the soft float and arch check. This is subtly
  // different from gcc, we follow the intent which was that it should be set
  // when Neon instructions are actually available.
  if ((FPU & NeonFPU) && !SoftFloat && ArchVersion >= 7) {
    Builder.defineMacro("__ARM_NEON", "1");
    Builder.defineMacro("__ARM_NEON__");
    // current AArch32 NEON implementations do not support double-precision
    // floating-point even when it is present in VFP.
    Builder.defineMacro("__ARM_NEON_FP",
                        "0x" + Twine::utohexstr(HW_FP & ~HW_FP_DP));
  }

Ard Biesheuvel recommended explicitly adding '-march=armv7-a' at the
beginning of the NEON_FLAGS definitions so that __ARM_NEON__ always gets
definined by Clang. This doesn't functionally change anything because
that code will only run where NEON is supported, which is implicitly
armv7.

Link: https://github.com/ClangBuiltLinux/linux/issues/287Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 02106f88 ]

Since kprobe breakpoing handler is using bsearch(), probing on this
routine can cause recursive breakpoint problem.

int3
 ->do_int3()
   ->ftrace_int3_handler()
     ->ftrace_location()
       ->ftrace_location_range()
         ->bsearch() -> int3

Prohibit probing on bsearch().
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/154998813406.31052.8791425358974650922.stgit@devboxSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit cecf3e3e ]

This commit refactors the chassis-type detection introduced by
commit 53fa1f6e ("ACPI / video: Only default only_lcd to true on
Win8-ready _desktops_") (where desktop means anything without a builtin
screen).

The DMI chassis_type is an unsigned integer, so rather then doing a
whole bunch of string-compares on it, convert it to an int and feed
the result to a switch case.

Note the switch case uses hex values, this is done because the spec
uses hex values too. This changes the check for "Main Server Chassis"
from checking for 11 decimal to 11 hexadecimal, this is a bug fix,
the original check for 11 decimal was wrong.

Fixes: 53fa1f6e ("ACPI / video: Only default only_lcd to true ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[ rjw: Drop redundant return statements ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c6ac9f9f ]

Allocator swaps the pending requests with 0 when it starts
working. This means that relying on it n RX path to decide if
to move to emergency is not always a good idea, since it may
be zero, but there are still a lot of unallocated RBs in the
system. Change allocator to decrement the pending requests on
real time. It is more expensive since it accesses the atomic
variable more times, but it gives the RX path a better idea
of the system's status.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 868a1e86 ("iwlwifi: pcie: avoid empty free RB queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5ddb0869 ]

I've stumbled upon a kernel crash and the logs
pointed me towards the lp5562 driver:

> <4>[306013.841294] lp5562 0-0030: Direct firmware load for lp5562 failed with error -2
> <4>[306013.894990] lp5562 0-0030: Falling back to user helper
> ...
> <3>[306073.924886] lp5562 0-0030: firmware request failed
> <1>[306073.939456] Unable to handle kernel NULL pointer dereference at virtual address 00000000
> <4>[306074.251011] PC is at _raw_spin_lock+0x1c/0x58
> <4>[306074.255539] LR is at release_firmware+0x6c/0x138
> ...

After taking a look I noticed firmware_release()
could be called with either NULL or a dangling
pointer.

Fixes: 10c06d17 ("leds-lp55xx: support firmware interface")
Signed-off-by: Michal Kazior <michal@plume.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0d28f494 ]

When performing a warm reset in ishtp bus driver, the ishtp_cl_device
will not be removed, its fw_client still points to the already freed
ishtp_device.fw_clients array.

Later after driver finishing ishtp client enumeration, this dangling
pointer may cause driver to bind the wrong ishtp_cl_device to the new
client, causing wrong callback to be called for messages intended for
the new client.

This helps in development of firmware where frequent switching of
firmwares is required without Linux reboot.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Tested-by: Hongyan Song <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit cc4b1242 ]

The preadv2 and pwritev2 syscalls are supposed to emulate the readv and
writev syscalls when offset == -1. Therefore the compat code should
check for offset before calling do_compat_preadv64 and
do_compat_pwritev64. This is the case for the preadv2 and pwritev2
syscalls, but handling of offset == -1 is missing in their 64-bit
equivalent.

This patch fixes that, calling do_compat_readv and do_compat_writev when
offset == -1. This fixes the following glibc tests on x32:
 - misc/tst-preadvwritev2
 - misc/tst-preadvwritev64v2

Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8d20dcef ]

Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:

 v4l2_m2m_next_buf
 v4l2_m2m_last_buf
 v4l2_m2m_buf_remove
 v4l2_m2m_next_src_buf
 v4l2_m2m_next_dst_buf
 v4l2_m2m_last_src_buf
 v4l2_m2m_last_dst_buf
 v4l2_m2m_src_buf_remove
 v4l2_m2m_dst_buf_remove

return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.

Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 30fa627b ]

Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:

 v4l2_m2m_next_buf
 v4l2_m2m_last_buf
 v4l2_m2m_buf_remove
 v4l2_m2m_next_src_buf
 v4l2_m2m_next_dst_buf
 v4l2_m2m_last_src_buf
 v4l2_m2m_last_dst_buf
 v4l2_m2m_src_buf_remove
 v4l2_m2m_dst_buf_remove

return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.

Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4a88f898 ]

Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:

 v4l2_m2m_next_buf
 v4l2_m2m_last_buf
 v4l2_m2m_buf_remove
 v4l2_m2m_next_src_buf
 v4l2_m2m_next_dst_buf
 v4l2_m2m_last_src_buf
 v4l2_m2m_last_dst_buf
 v4l2_m2m_src_buf_remove
 v4l2_m2m_dst_buf_remove

return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.

Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 43c14519 ]

Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:

 v4l2_m2m_next_buf
 v4l2_m2m_last_buf
 v4l2_m2m_buf_remove
 v4l2_m2m_next_src_buf
 v4l2_m2m_next_dst_buf
 v4l2_m2m_last_src_buf
 v4l2_m2m_last_dst_buf
 v4l2_m2m_src_buf_remove
 v4l2_m2m_dst_buf_remove

return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.

Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8fa857da ]

The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.

Detected by coccinelle with the following warnings:
./sound/soc/fsl/imx-sgtl5000.c:169:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
./sound/soc/fsl/imx-sgtl5000.c:177:1-7: ERROR: missing put_device;
call of_find_device_by_node on line 105, but without a corresponding
object release within this function.
Signed-off-by: Wen Yang <yellowriver2010@hotmail.com>
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 03d30971 ]

Commit 489338a7 ("perf tests evsel-tp-sched: Fix bitwise operator")
causes test case 14 "Parse sched tracepoints fields" to fail on s390.

This test succeeds on x86.

In fact this test now fails on all architectures with type char treated
as type unsigned char.

The root cause is the signed-ness of character arrays in the tracepoints
sched_switch for structure members prev_comm and next_comm.

On s390 the output of:

 [root@m35lp76 perf]# cat /sys/kernel/debug/tracing/events/sched/sched_switch/format
 name: sched_switch
 ID: 287
 format:
   field:unsigned short common_type; offset:0; size:2;	signed:0;
   ...
   field:char prev_comm[16]; offset:8; size:16;	signed:0;
   ...
   field:char next_comm[16]; offset:40; size:16; signed:0;

reveals the character arrays prev_comm and next_comm are per
default unsigned char and have values in the range of 0..255.

On x86 both fields are signed as this output shows:
 [root@f29]# cat /sys/kernel/debug/tracing/events/sched/sched_switch/format
 name: sched_switch
 ID: 287
 format:
   field:unsigned short common_type; offset:0; size:2;	signed:0;
   ...
   field:char prev_comm[16]; offset:8; size:16;	signed:1;
   ...
   field:char next_comm[16]; offset:40; size:16; signed:1;

and the character arrays prev_comm and next_comm are per default signed
char and have values in the range of -1..127.  The implementation of
type char is architecture specific.

Since the character arrays in both tracepoints sched_switch and
sched_wakeup should contain ascii characters, simply omit the check for
signedness in the test case.

Output before:

  [root@m35lp76 perf]# ./perf test -F 14
  14: Parse sched tracepoints fields                        :
  --- start ---
  sched:sched_switch: "prev_comm" signedness(0) is wrong, should be 1
  sched:sched_switch: "next_comm" signedness(0) is wrong, should be 1
  sched:sched_wakeup: "comm" signedness(0) is wrong, should be 1
  ---- end ----
  14: Parse sched tracepoints fields                        : FAILED!
  [root@m35lp76 perf]#

Output after:

  [root@m35lp76 perf]# ./perf test -Fv 14
  14: Parse sched tracepoints fields                        :
  --- start ---
  ---- end ----
  Parse sched tracepoints fields: Ok
  [root@m35lp76 perf]#

Fixes: 489338a7 ("perf tests evsel-tp-sched: Fix bitwise operator")
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20190219153639.31267-1-tmricht@linux.ibm.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bcf3b67d ]

when create DMA pool for cmd frames failed, we should return -ENOMEM,
instead of 0.
In some case in:

    megasas_init_adapter_fusion()

    -->megasas_alloc_cmds()
       -->megasas_create_frame_pool
          create DMA pool failed,
        --> megasas_free_cmds() [1]

    -->megasas_alloc_cmds_fusion()
       failed, then goto fail_alloc_cmds.
    -->megasas_free_cmds() [2]

we will call megasas_free_cmds twice, [1] will kfree cmd_list,
[2] will use cmd_list.it will cause a problem:

Unable to handle kernel NULL pointer dereference at virtual address
00000000
pgd = ffffffc000f70000
[00000000] *pgd=0000001fbf893003, *pud=0000001fbf893003,
*pmd=0000001fbf894003, *pte=006000006d000707
Internal error: Oops: 96000005 [#1] SMP
 Modules linked in:
 CPU: 18 PID: 1 Comm: swapper/0 Not tainted
 task: ffffffdfb9290000 ti: ffffffdfb923c000 task.ti: ffffffdfb923c000
 PC is at megasas_free_cmds+0x30/0x70
 LR is at megasas_free_cmds+0x24/0x70
 ...
 Call trace:
 [<ffffffc0005b779c>] megasas_free_cmds+0x30/0x70
 [<ffffffc0005bca74>] megasas_init_adapter_fusion+0x2f4/0x4d8
 [<ffffffc0005b926c>] megasas_init_fw+0x2dc/0x760
 [<ffffffc0005b9ab0>] megasas_probe_one+0x3c0/0xcd8
 [<ffffffc0004a5abc>] local_pci_probe+0x4c/0xb4
 [<ffffffc0004a5c40>] pci_device_probe+0x11c/0x14c
 [<ffffffc00053a5e4>] driver_probe_device+0x1ec/0x430
 [<ffffffc00053a92c>] __driver_attach+0xa8/0xb0
 [<ffffffc000538178>] bus_for_each_dev+0x74/0xc8
  [<ffffffc000539e88>] driver_attach+0x28/0x34
 [<ffffffc000539a18>] bus_add_driver+0x16c/0x248
 [<ffffffc00053b234>] driver_register+0x6c/0x138
 [<ffffffc0004a5350>] __pci_register_driver+0x5c/0x6c
 [<ffffffc000ce3868>] megasas_init+0xc0/0x1a8
 [<ffffffc000082a58>] do_one_initcall+0xe8/0x1ec
 [<ffffffc000ca7be8>] kernel_init_freeable+0x1c8/0x284
 [<ffffffc0008d90b8>] kernel_init+0x1c/0xe4
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2612d723 ]

Using CX-3 virtual functions, either from a bare-metal machine or
pass-through from a VM, MAD packets are proxied through the PF driver.

Since the VF drivers have separate name spaces for MAD Transaction Ids
(TIDs), the PF driver has to re-map the TIDs and keep the book keeping
in a cache.

Following the RDMA Connection Manager (CM) protocol, it is clear when
an entry has to evicted form the cache. But life is not perfect,
remote peers may die or be rebooted. Hence, it's a timeout to wipe out
a cache entry, when the PF driver assumes the remote peer has gone.

During workloads where a high number of QPs are destroyed concurrently,
excessive amount of CM DREQ retries has been observed

The problem can be demonstrated in a bare-metal environment, where two
nodes have instantiated 8 VFs each. This using dual ported HCAs, so we
have 16 vPorts per physical server.

64 processes are associated with each vPort and creates and destroys
one QP for each of the remote 64 processes. That is, 1024 QPs per
vPort, all in all 16K QPs. The QPs are created/destroyed using the
CM.

When tearing down these 16K QPs, excessive CM DREQ retries (and
duplicates) are observed. With some cat/paste/awk wizardry on the
infiniband_cm sysfs, we observe as sum of the 16 vPorts on one of the
nodes:

cm_rx_duplicates:
      dreq  2102
cm_rx_msgs:
      drep  1989
      dreq  6195
       rep  3968
       req  4224
       rtu  4224
cm_tx_msgs:
      drep  4093
      dreq 27568
       rep  4224
       req  3968
       rtu  3968
cm_tx_retries:
      dreq 23469

Note that the active/passive side is equally distributed between the
two nodes.

Enabling pr_debug in cm.c gives tons of:

[171778.814239] <mlx4_ib> mlx4_ib_multiplex_cm_handler: id{slave:
1,sl_cm_id: 0xd393089f} is NULL!

By increasing the CM_CLEANUP_CACHE_TIMEOUT from 5 to 30 seconds, the
tear-down phase of the application is reduced from approximately 90 to
50 seconds. Retries/duplicates are also significantly reduced:

cm_rx_duplicates:
      dreq  2460
[]
cm_tx_retries:
      dreq  3010
       req    47

Increasing the timeout further didn't help, as these duplicates and
retries stems from a too short CMA timeout, which was 20 (~4 seconds)
on the systems. By increasing the CMA timeout to 22 (~17 seconds), the
numbers fell down to about 10 for both of them.

Adjustment of the CMA timeout is not part of this commit.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ab2c4e25 ]

Give precision identifiers to the two snprintf() formatting the priority
and TC strings to avoid producing these two warnings:

drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_prio_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:37: warning: '%d'
directive output may be truncated writing between 1 and 3 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
                                     ^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:3: note: 'snprintf'
output between 3 and 36 bytes into a destination of size 32
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     mlxsw_sp_port_hw_prio_stats[i].str, prio);
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_tc_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:37: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
                                     ^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:3: note: 'snprintf'
output between 3 and 44 bytes into a destination of size 32
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     mlxsw_sp_port_hw_tc_stats[i].str, tc);
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 135e7245 ]

Provide precision hints to snprintf() since we know the destination
buffer size of the RX/TX ring names are IFNAMSIZ + 5 - 1. This fixes the
following warnings:

drivers/net/ethernet/intel/e1000e/netdev.c: In function
'e1000_request_msix':
drivers/net/ethernet/intel/e1000e/netdev.c:2109:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
     "%s-rx-0", netdev->name);
             ^
drivers/net/ethernet/intel/e1000e/netdev.c:2107:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
   snprintf(adapter->rx_ring->name,
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     sizeof(adapter->rx_ring->name) - 1,
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     "%s-rx-0", netdev->name);
     ~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/e1000e/netdev.c:2125:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
     "%s-tx-0", netdev->name);
             ^
drivers/net/ethernet/intel/e1000e/netdev.c:2123:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
   snprintf(adapter->tx_ring->name,
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     sizeof(adapter->tx_ring->name) - 1,
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     "%s-tx-0", netdev->name);
     ~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a6327b5e ]

When running OMAP1 kernel on QEMU, MMC access is annoyingly noisy:

	MMC: CTO of 0xff and 0xfe cannot be used!
	MMC: CTO of 0xff and 0xfe cannot be used!
	MMC: CTO of 0xff and 0xfe cannot be used!
	[ad inf.]

Emulator warnings appear to be valid. The TI document SPRU680 [1]
("OMAP5910 Dual-Core Processor MultiMedia Card/Secure Data Memory Card
(MMC/SD) Reference Guide") page 36 states that the maximum timeout is 253
cycles and "0xff and 0xfe cannot be used".

Fix by using 0xfd as the maximum timeout.

Tested using QEMU 2.5 (Siemens SX1 machine, OMAP310), and also checked on
real hardware using Palm TE (OMAP310), Nokia 770 (OMAP1710) and Nokia N810
(OMAP2420) that MMC works as before.

[1] http://www.ti.com/lit/ug/spru680/spru680.pdf

Fixes: 730c9b7e ("[MMC] Add OMAP MMC host driver")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 032ebd85 ]

L1 tables are allocated with __get_dma_pages, and therefore already
ignored by kmemleak.

Without this, the kernel would print this error message on boot,
when the first L1 table is allocated:

[    2.810533] kmemleak: Trying to color unknown object at 0xffffffd652388000 as Black
[    2.818190] CPU: 5 PID: 39 Comm: kworker/5:0 Tainted: G S                4.19.16 #8
[    2.831227] Workqueue: events deferred_probe_work_func
[    2.836353] Call trace:
...
[    2.852532]  paint_ptr+0xa0/0xa8
[    2.855750]  kmemleak_ignore+0x38/0x6c
[    2.859490]  __arm_v7s_alloc_table+0x168/0x1f4
[    2.863922]  arm_v7s_alloc_pgtable+0x114/0x17c
[    2.868354]  alloc_io_pgtable_ops+0x3c/0x78
...

Fixes: e5fc9753 ("iommu/io-pgtable: Add ARMv7 short descriptor support")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 74ffe79a ]

Mostly unwind is done with irqs enabled however SLUB may call it with
irqs disabled while creating a new SLUB cache.

I had system freeze while loading a module which called
kmem_cache_create() on init. That means SLUB's __slab_alloc() disabled
interrupts and then

->new_slab_objects()
 ->new_slab()
  ->setup_object()
   ->setup_object_debug()
    ->init_tracking()
     ->set_track()
      ->save_stack_trace()
       ->save_stack_trace_tsk()
        ->walk_stackframe()
         ->unwind_frame()
          ->unwind_find_idx()
           =>spin_lock_irqsave(&unwind_lock);
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5666dfd1 ]

SDM845 has ETMv4.2 and can use the existing etm4x driver.
But the current etm driver checks only for ETMv4.0 and
errors out for other etm4x versions. This patch adds this
missing support to enable SoC's with ETMv4x to use same
driver by checking only the ETM architecture major version
number.

Without this change, we get below error during etm probe:

/ # dmesg | grep etm
[    6.660093] coresight-etm4x: probe of 7040000.etm failed with error -22
[    6.666902] coresight-etm4x: probe of 7140000.etm failed with error -22
[    6.673708] coresight-etm4x: probe of 7240000.etm failed with error -22
[    6.680511] coresight-etm4x: probe of 7340000.etm failed with error -22
[    6.687313] coresight-etm4x: probe of 7440000.etm failed with error -22
[    6.694113] coresight-etm4x: probe of 7540000.etm failed with error -22
[    6.700914] coresight-etm4x: probe of 7640000.etm failed with error -22
[    6.707717] coresight-etm4x: probe of 7740000.etm failed with error -22

With this change, etm probe is successful:

/ # dmesg | grep etm
[    6.659198] coresight-etm4x 7040000.etm: CPU0: ETM v4.2 initialized
[    6.665848] coresight-etm4x 7140000.etm: CPU1: ETM v4.2 initialized
[    6.672493] coresight-etm4x 7240000.etm: CPU2: ETM v4.2 initialized
[    6.679129] coresight-etm4x 7340000.etm: CPU3: ETM v4.2 initialized
[    6.685770] coresight-etm4x 7440000.etm: CPU4: ETM v4.2 initialized
[    6.692403] coresight-etm4x 7540000.etm: CPU5: ETM v4.2 initialized
[    6.699024] coresight-etm4x 7640000.etm: CPU6: ETM v4.2 initialized
[    6.705646] coresight-etm4x 7740000.etm: CPU7: ETM v4.2 initialized
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1749ef00 ]

We had a test-report where, under memory pressure, adding LUNs to the
systems would fail (the tests add LUNs strictly in sequence):

[ 5525.853432] scsi 0:0:1:1088045124: Direct-Access     IBM      2107900          .148 PQ: 0 ANSI: 5
[ 5525.853826] scsi 0:0:1:1088045124: alua: supports implicit TPGS
[ 5525.853830] scsi 0:0:1:1088045124: alua: device naa.6005076303ffd32700000000000044da port group 0 rel port 43
[ 5525.853931] sd 0:0:1:1088045124: Attached scsi generic sg10 type 0
[ 5525.854075] sd 0:0:1:1088045124: [sdk] Disabling DIF Type 1 protection
[ 5525.855495] sd 0:0:1:1088045124: [sdk] 2097152 512-byte logical blocks: (1.07 GB/1.00 GiB)
[ 5525.855606] sd 0:0:1:1088045124: [sdk] Write Protect is off
[ 5525.855609] sd 0:0:1:1088045124: [sdk] Mode Sense: ed 00 00 08
[ 5525.855795] sd 0:0:1:1088045124: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5525.857838]  sdk: sdk1
[ 5525.859468] sd 0:0:1:1088045124: [sdk] Attached SCSI disk
[ 5525.865073] sd 0:0:1:1088045124: alua: transition timeout set to 60 seconds
[ 5525.865078] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015070] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015213] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.587439] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
[ 5526.588562] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured

Looking at the code of scsi_alloc_sdev(), and all the calling contexts,
there seems to be no reason to use GFP_ATMOIC here. All the different
call-contexts use a mutex at some point, and nothing in between that
requires no sleeping, as far as I could see. Additionally, the code that
later allocates the block queue for the device (scsi_mq_alloc_queue())
already uses GFP_KERNEL.

There are similar allocations in two other functions:
scsi_probe_and_add_lun(), and scsi_add_lun(),; that can also be done with
GFP_KERNEL.

Here is the contexts for the three functions so far:

    scsi_alloc_sdev()
        scsi_probe_and_add_lun()
            scsi_sequential_lun_scan()
                __scsi_scan_target()
                    scsi_scan_target()
                        mutex_lock()
                    scsi_scan_channel()
                        scsi_scan_host_selected()
                            mutex_lock()
            scsi_report_lun_scan()
                __scsi_scan_target()
    	            ...
            __scsi_add_device()
                mutex_lock()
            __scsi_scan_target()
                ...
        scsi_report_lun_scan()
            ...
        scsi_get_host_dev()
            mutex_lock()

    scsi_probe_and_add_lun()
        ...

    scsi_add_lun()
        scsi_probe_and_add_lun()
            ...

So replace all these, and give them a bit of a better chance to succeed,
with more chances of reclaim.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 68ef2362 ]

According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.

This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.

Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.

When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8c2b43d2 ]

Add an of_node_put when a tested device node is not available.

The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):

// <smpl>
@@
identifier f;
local idexpression e;
expression x;
@@

e = f(...);
... when != of_node_put(e)
    when != x = e
    when != e = x
    when any
if (<+...of_device_is_available(e)...+>) {
  ... when != of_node_put(e)
(
  return e;
|
+ of_node_put(e);
  return ...;
)
}
// </smpl>

Fixes: 5343e674 ("crypto4xx: integrate ppc4xx-rng into crypto4xx")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit de77a53c ]

ies1 or ies2 might be null when code inside
_wil_cfg80211_merge_extra_ies access them.
Add explicit check for null and make sure ies1/ies2 are not
accessed in such a case.

spos might be null and be accessed inside
_wil_cfg80211_merge_extra_ies.
Add explicit check for null in the while condition statement
and make sure spos is not accessed in such a case.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7c5b019e ]

Fix buffer overflow observed when running perf test.

The overflow is when trying to evaluate "1ULL << (64 - 1)" which is
resulting in -9223372036854775808 which overflows the 20 character
buffer.

If is possible this bug has been reported before but I still don't see
any fix checked in:

See: https://www.spinics.net/lists/linux-perf-users/msg07714.htmlReported-by: Michael Sartain <mikesart@fastmail.com>
Reported-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Tony Jones <tonyj@suse.de>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Fixes: f7d82350 ("tools/events: Add files to create libtraceevent.a")
Link: http://lkml.kernel.org/r/20190228015532.8941-1-tonyj@suse.deSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit dce30ca9 ]

guard_bio_eod() can truncate a segment in bio to allow it to do IO on
odd last sectors of a device.

It already checks if the IO starts past EOD, but it does not consider
the possibility of an IO request starting within device boundaries can
contain more than one segment past EOD.

In such cases, truncated_bytes can be bigger than PAGE_SIZE, and will
underflow bvec->bv_len.

Fix this by checking if truncated_bytes is lower than PAGE_SIZE.

This situation has been found on filesystems such as isofs and vfat,
which doesn't check the device size before mount, if the device is
smaller than the filesystem itself, a readahead on such filesystem,
which spans EOD, can trigger this situation, leading a call to
zero_user() with a wrong size possibly corrupting memory.

I didn't see any crash, or didn't let the system run long enough to
check if memory corruption will be hit somewhere, but adding
instrumentation to guard_bio_end() to check truncated_bytes size, was
enough to see the error.

The following script can trigger the error.

MNT=/mnt
IMG=./DISK.img
DEV=/dev/loop0

mkfs.vfat $IMG
mount $IMG $MNT
cp -R /etc $MNT &> /dev/null
umount $MNT

losetup -D

losetup --find --show --sizelimit 16247280 $IMG
mount $DEV $MNT

find $MNT -type f -exec cat {} + >/dev/null

Kudos to Eric Sandeen for coming up with the reproducer above
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>