- 14 Sep, 2010 26 commits
-
-
Stanislaw Gruszka authored
Assure (partially) we call ieee80211_scan_completed() only once when scan was requested from mac80211. Code path that first clear STATUS_SCANNING bit is responsible to call ieee80211_scan_completed(). Before the call, we check if mac80211 really request the scan. Still persist some cases when we behave wrong, that will be addressed in the next patches. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Acked-by:
Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Stanislaw Gruszka authored
Since on timeout version of iwl_scan_cancel procedure we can sleep, do not have to schedule abort_scan work to begin and perform scanning, can do this directly. Also now, as we do not queue abort_scan from restart work anymore, we can queue abort_scan to priv->workqueue. Don't drop mutex when waiting for scan complete. Use STATUS_HW_SCAN bit to check if scanning is currently pending, because STATUS_SCANNING will be cleared only with priv->mutex taken. Signed-off-by:
-
Stanislaw Gruszka authored
When we are not able to send abort command to firmware, notify mac80211 that we complete scan, as we will newer do it lately. Check for all possible errors that low level sending command procedure does not check, to assure we catch all failures cases. Patch fix one of the causes of wdev_cleanup_work warning reported at https://bugzilla.redhat.com/show_bug.cgi?id=593566Signed-off-by:
-
Stanislaw Gruszka authored
Always cancel scan when stooping device and scan is currently pending, we should newer have scan running after down device. To assure we start scan cancel from restart work we have to schedule abort_scan to different workqueue than priv->workqueue. Patch fix not cancel scanning when restarting firmware, what is one of the causes of wdev_cleanup_work warning (together with permanent network connection lost) reported at https://bugzilla.redhat.com/show_bug.cgi?id=593566Signed-off-by:
-
Johannes Berg authored
Move the scan completed flags handling so that we can notify mac80211 about aborted scans with the correct status. Also queue the scan_completed work before the BT status update so that it won't see the bits still set (unless a new scan was started in which case that's fine.) Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
Rather than duplicating all the checks and even in case of errors accepting the scan request from mac80211, we can push the checks to the caller and in all error cases reject the scan request right away (rather than accepting and then saying it was aborted). Signed-off-by:
-
Johannes Berg authored
There are a number of conf variables that are unused, remove them. Signed-off-by:
-
Steve deRosier authored
hdr pointer is left dangling after call to ieee80211_skb_resize. This can cause guards around mesh path selection to fail. Signed-off-by:
Steve deRosier <steve@cozybit.com> Signed-off-by:
-
Bill Jordan authored
There is a path in nl80211_set_wiphy where result is tested but uninitialized. I am hitting this path when I attempt: sh# iw dev wlan0 set channel 10 command failed: Unknown error 1069727332 (-1069727332) Signed-off-by:
William Jordan <bjordan@rajant.com> Signed-off-by:
-
Nikitas Angelinas authored
Replace sizeof(rtap_namespace_sizes) / sizeof(rtap_namespace_sizes[0]) with ARRAY_SIZE(rtap_namespace_sizes) in net/wireless/radiotap.c Signed-off-by:
Nikitas Angelinas <nikitasangelinas@gmail.com> Signed-off-by:
-
Nikitas Angelinas authored
Replace (sizeof(ofdm_level_table)/sizeof(ofdm_level_table[0]) with ARRAY_SIZE(ofdm_level_table), and (sizeof(cck_level_table)/ sizeof(cck_level_table[0]) with ARRAY_SIZE(cck_level_table) in drivers/net/wireless/ath/ath9k/ani.c Signed-off-by:
-
Fabio Rossi authored
Don't generate calibration errors messages when not needed. Signed-off-by:
Fabio Rossi <rossi.f@inwind.it> Acked-by:
Bruno Randolf <br1@einfach.org> Signed-off-by:
-
Helmut Schaa authored
Fix a typo introduced in "rt2x00: Add helper function for reporting tx status" that results in an oops in rt2x00lib_txdone. Reported-by:
Pavel Roskin <proski@gnu.org> Signed-off-by:
Helmut Schaa <helmut.schaa@googlemail.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Helmut Schaa authored
We're handling both, the CSR_BEACON_DONE and the CSR_TWAKEUP interrupts in rt61pci. However, these interrupts are masked out by default. Fix this. Found via pure code inspection. Signed-off-by:
-
Helmut Schaa authored
We don't use all available interrupts in rt2800pci. Mask out all unused interrupts to avoid waking up without having anything to do. Signed-off-by:
-
Helmut Schaa authored
Previously rt2x00 was always updating all erp related config variables even though mac80211 might only have changed one. Hence, pass the changed flags to the config_erp driver callback so that the driver can limit the changes to the correct values. This fixes an issue in AP mode where the beacon interval is not initialized (and thus zero) but still sent to the hardware causing an interrupt storm on rt2800pci hanging the system. Signed-off-by:
-
Helmut Schaa authored
Since we're not using the AMPDU_BA_WINSIZE register to force the BlockAck window size (we specify it in every TXWI) we should initialize it to 0. Signed-off-by:
-
Lars Ericsson authored
The test if antenna diversity is at all enabled uses a local variable 'flags' to prepare the test condition, but uses 'ant->flags' when the test is evaluated. The effect is that the diversity evaluation will never start. I can see two solutions, use the 'flag' in the test condition or revert the local flag change. My attached patch took alternative two. Then the evaluation start but it will still not switch antenna. The problem is a code section in rt2x00lib_config_antenna (). The effect of that code section is that any change the diversity function perform will be effectively shorten and no antenna selection command issued. The attached patch will filter out any ANTENNA_SW_DIVERSITY setting but forward all other Signed-off-by:
Lars Ericsson <lars_ericsson@telia.com> Signed-off-by:
-
Rajkumar Manoharan authored
To reduce scan time, enable fastcc for AR7010 (fastcc == fast channel change -- JWL) Signed-off-by:
Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by:
-
Ohad Ben-Cohen authored
Do not maintain a persistent sdio_claim_host state. Instead, claim host before doing IO and release host soon after. This fixes several mmc deadlock scenarios, e.g. during suspend/resume. Signed-off-by:
Ohad Ben-Cohen <ohad@wizery.com> Acked-by:
Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by:
-
Christian Lamparter authored
Signed-off-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
Christian Lamparter authored
Signed-off-by:
-
Christian Lamparter authored
Signed-off-by:
-
Christian Lamparter authored
Signed-off-by:
-
Christian Lamparter authored
Signed-off-by:
-
Christian Lamparter authored
Signed-off-by:
-
- 11 Sep, 2010 10 commits
-
-
Wey-Yi Guy authored
Move the duplicated code into single static function. Signed-off-by: -
Wey-Yi Guy authored
Clear the "start calib" flag only for new association, The flag will be set in post_associate function to trigger the runtime calibration. Set this flag to "0" will stop the runtime sensitivity calibration Signed-off-by: -
Johannes Berg authored
The iwl_adjust_beacon_interval function is a bit of black magic, so add comments to it describing what it does. Also, in the case when there's no beacon interval set, program the default into the device (instead of adjusting, which results in the max) since using the max in that case interacts badly with dual-mode/PAN parameters. Also update the PAN parameters accordingly and use the same constant as here. Signed-off-by:
-
Johannes Berg authored
In dual-mode, a number of scenarios need to be considered, and the firmware can be very picky about them. Adjust the timing (most importantly the beacon interval) according to the different modes. Signed-off-by:
-
Johannes Berg authored
When the PAN context is unused, there's no need to continually update it in the device. So track which contexts are active (with the special case that the WLAN context is always active ...) and only send their commands to the device when needed. Signed-off-by:
-
Wey-Yi Guy authored
Even driver use rts/cts protection mode for aggregation packets by default. Allow the protection mode to be configure through debugfs Signed-off-by: -
Johannes Berg authored
When the beacon interval needs to be changed, all we need to do is send updated timing to the device. Signed-off-by:
-
Johannes Berg authored
When only the PAN side was active, we gave no time to the WLAN context, which is OK unless we are scanning, which always happens on the WLAN context. Fix this. Signed-off-by:
-
Wey-Yi Guy authored
When sysassert happen, uCode will report the error code, driver dump the information to dmesg. Here also remember the last error code for future reference. Signed-off-by: -
Tomas Winkler authored
The default LQ is filled decreasingly using iwl_get_prev_ieee_rate from a starting rate. Since the starting rate is already the lowest one for a specific band it should be actually filled evenly with the starting rate: 1M and 6M for 5.2GHZ and 2.4GH respectively. The bug is that for for A or G-only it decreases to CCK rates which are not supported. iwl_get_prev_ieee_rate function is just not band aware. This affects broadcast station which lq table is not updated by rs algorithm G-only scenario is not treated by this patch iwl_get_prev_ieee_rate is removed completely as it is not used in other contexts Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
-
- 07 Sep, 2010 4 commits
-
-
Julia Lawall authored
The function has an unsigned return type, but returns a negative constant to indicate an error condition. Another error condition in the same function is indicated by returning 0, and indeed the only call to the function checks for 0 to detect errors, so the return of a negative value it converted to a return of 0. A sematic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @exists@ identifier f; constant C; @@ unsigned f(...) { <+... * return -C; ...+> } // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Michael Büsch authored
This adds an error message for the eeprom request failure case. This way it's easier for the user to figure out what went wrong. Signed-off-by:
Michael Büsch <mb@bu3sch.de> Acked-by:
-
Rajkumar Manoharan authored
For AR9271 chips, if partial reset is done while scanning, the cycpwrThr1 will be set to maximum. This causes the degrade in DL throughput. So restore the ANI registers to default during the partial reset. Signed-off-by:
-
Rajkumar Manoharan authored
By enabling fastcc, the scan time reduced to half. Signed-off-by:
-
