During hci down we observed IBS sleep commands are queued in the Tx
buffer and hci_uart_write_work is sending data to the chip which is
not required as the chip is powered off. This patch will disable IBS
and flush the Tx buffer before we turn off the chip.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch will help to stop frame reassembly errors while changing
the baudrate. This is because host send a change baudrate request
command to the chip with 115200 bps, Whereas chip will change their
UART clocks to the enable for new baudrate and sends the response
for the change request command with newer baudrate, On host side
we are still operating in 115200 bps which results of reading garbage
data. Here we are pulling RTS line, so that chip we will wait to send data
to host until host change its baudrate.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

wcn3990 requires a power pulse to turn ON/OFF along with
regulators. Sometimes we are observing the power pulses are sent
out with some time delay, due to queuing these commands. This is
causing synchronization issues with chip, which intern delay the
chip setup or may end up with communication issues.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Variable count is never zero inside the loop so the check if count is
zero is redundant and can be removed. Fix this.

Detected by CoverityScan, CID#1466880 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When releasing socket, it is possible to enter hci_sock_release() and
hci_sock_dev_event(HCI_DEV_UNREG) at the same time in different thread.
The reference count of hdev should be decremented only once from one of
them but if storing hdev to local variable in hci_sock_release() before
detached from socket and setting to NULL in hci_sock_dev_event(),
hci_dev_put(hdev) is unexpectedly called twice. This is resolved by
referencing hdev from socket after bt_sock_unlink() in
hci_sock_release().

Reported-by: syzbot+fdc00003f4efff43bc5b@syzkaller.appspotmail.com
Signed-off-by: Myungho Jung <mhjungk@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If BT operations (BREDR inquiry/LE scan) were triggered
through the stack, followed by BT turn off through
'hciconfig hci0 down', the controller would still be active
and consume power.
Also, there is a possibility that a race condition/
synchronization issue might arise on the subsequent BT turn
on, as the controller might try to push the
events that were queued up before processing the HCI Reset
command.

btusb_shutdown_intel_new routine shall reset the controller
and stop all BT operation.
Advantages:
	1. Power save on the platform
	2. Host and controller will be in Sync.
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The btusb_intel_cmd_timeout() is called from workqueue contexts,
so use the helper functions that can sleep.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Realtek bluetooth may not work after reboot:
[   12.446130] Bluetooth: hci0: RTL: rtl: unknown IC info, lmp subver a99e, hci rev 826c, hci ver 0008

This is a regression introduced by commit 26503ad2 ("Bluetooth:
btrtl: split the device initialization into smaller parts"). The new
logic errors out early when no matching IC info can be found, in this
case it means the firmware is already loaded.

So let's assume the firmware is already loaded when we can't find
matching IC info, like the old logic did.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201921
Fixes: 26503ad2 ("Bluetooth: btrtl: split the device initialization into smaller parts")
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Don't populate the const array hw_err on the stack but instead make
it static. Makes the object code smaller by 45 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
 100880	  21090	   1088	 123058	  1e0b2	linux/net/bluetooth/hci_core.o

After:
   text	   data	    bss	    dec	    hex	filename
 100739	  21186	   1088	 123013	  1e085	linux/net/bluetooth/hci_core.o

(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If the platform provides it, use the reset gpio to reset the Intel BT
chip, as part of cmd_timeout handling. This has been found helpful on
Intel bluetooth controllers where the firmware gets stuck and the only
way out is a hard reset pin provided by the platform.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Add a hook to allow the BT driver to do device or command specific
handling in case of timeouts. This is to be used by Intel driver to
reset the device after certain number of timeouts.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

USB devices permanently connected to USB ports may be described in ACPI
tables and share ACPI devices with ports they are connected to. See [1]
for details.

This will allow us to describe sideband resources for devices, such as,
for example, hard reset line for BT USB controllers.

[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/bringup/other-acpi-namespace-objects#acpi-namespace-hierarchy-and-adr-for-embedded-usb-devicesSigned-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Rajat Jain <rajatja@google.com> (changed how we get the usb_port)
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In preparation for handling embedded USB devices let's split
usb_acpi_find_companion() into usb_acpi_find_companion_for_device() and
usb_acpi_find_companion_for_port().
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

This patch fixes the following warnings:

net/bluetooth/rfcomm/core.c:479:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
net/bluetooth/l2cap_core.c:4223:6: warning: this statement may fall through [-Wimplicit-fallthrough=]

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The function l2cap_get_conf_opt will return L2CAP_CONF_OPT_SIZE + opt->len
as length value. The opt->len however is in control over the remote user
and can be used by an attacker to gain access beyond the bounds of the
actual packet.

To prevent any potential leak of heap memory, it is enough to check that
the resulting len calculation after calling l2cap_get_conf_opt is not
below zero. A well formed packet will always return >= 0 here and will
end with the length value being zero after the last option has been
parsed. In case of malformed packets messing with the opt->len field the
length value will become negative. If that is the case, then just abort
and ignore the option.

In case an attacker uses a too short opt->len value, then garbage will
be parsed, but that is protected by the unknown option handling and also
the option parameter size checks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

When doing option parsing for standard type values of 1, 2 or 4 octets,
the value is converted directly into a variable instead of a pointer. To
avoid being tricked into being a pointer, check that for these option
types that sizes actually match. In L2CAP every option is fixed size and
thus it is prudent anyway to ensure that the remote side sends us the
right option size along with option paramters.

If the option size is not matching the option type, then that option is
silently ignored. It is a protocol violation and instead of trying to
give the remote attacker any further hints just pretend that option is
not present and proceed with the default values. Implementation
following the specification and its qualification procedures will always
use the correct size and thus not being impacted here.

To keep the code readable and consistent accross all options, a few
cosmetic changes were also required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

I can't see that these drivers use the old GPIO inlcudes in any
way, drop <linux/gpio.h> and <linux/of_gpio.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

With commit e1633762 ("Bluetooth: Handle bt_accept_enqueue() socket
atomically") lock_sock[_nested]() is used to acquire the socket lock
before manipulating the socket. lock_sock[_nested]() may block, which
is problematic since bt_accept_enqueue() can be called in bottom half
context (e.g. from rfcomm_connect_ind()):

[<ffffff80080d81ec>] __might_sleep+0x4c/0x80
[<ffffff800876c7b0>] lock_sock_nested+0x24/0x58
[<ffffff8000d7c27c>] bt_accept_enqueue+0x48/0xd4 [bluetooth]
[<ffffff8000e67d8c>] rfcomm_connect_ind+0x190/0x218 [rfcomm]

Add a parameter to bt_accept_enqueue() to indicate whether the
function is called from BH context, and acquire the socket lock
with bh_lock_sock_nested() if that's the case.

Also adapt all callers of bt_accept_enqueue() to pass the new
parameter:

- l2cap_sock_new_connection_cb()
  - uses lock_sock() to lock the parent socket => process context

- rfcomm_connect_ind()
  - acquires the parent socket lock with bh_lock_sock() => BH
    context

- __sco_chan_add()
  - called from sco_chan_add(), which is called from sco_connect().
    parent is NULL, hence bt_accept_enqueue() isn't called in this
    code path and we can ignore it
  - also called from sco_conn_ready(). uses bh_lock_sock() to acquire
    the parent lock => BH context

Fixes: e1633762 ("Bluetooth: Handle bt_accept_enqueue() socket atomically")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

This patch adds support for 8977 chipset to mwifiex with SDIO
interface. Register offsets and supported feature flags are
updated. Firmware image used will be mrvl/sd8977_uapsta.bin.
Signed-off-by: Hemantkumar Suthar <shemant@marvell.com>
Signed-off-by: Rakesh Parmar <rakeshp@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

h4_recv_buf() callers store the return value to socket buffer and
recursively pass the buffer to h4_recv_buf() without protection. So,
ERR_PTR returned from h4_recv_buf() can be dereferenced, if called again
before setting the socket buffer to NULL from previous error. Check if
skb is ERR_PTR in h4_recv_buf().

Reported-by: syzbot+017a32f149406df32703@syzkaller.appspotmail.com
Signed-off-by: Myungho Jung <mhjungk@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The platform specific wake-up interrupt is optional. Don't print
an error message in case it is missing, merely inform the user in
this case.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Use dev_* variants to print messages in drivers.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.

Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().

Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.

Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().

Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch add qca_set_bdaddr() to set the device
address for latest Qualcomm Bluetooth chipset wcn3990 and above.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Completely minor snmp doc conflict.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull pstore fixes from Kees Cook:

 - Fix console ramoops to show the previous boot logs (Sai Prakash
   Ranjan)

 - Avoid allocation and leak of platform data

* tag 'pstore-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore/ram: Avoid allocation and leak of platform data
  pstore/ram: Fix console ramoops to show the previous boot logs

Pull gcc-plugins fixes from Kees Cook:
 "Fix ARM per-task stack protector plugin under GCC 9 (Ard Biesheuvel)"

* tag 'gcc-plugins-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  gcc-plugins: arm_ssp_per_task_plugin: fix for GCC 9+
  gcc-plugins: arm_ssp_per_task_plugin: sign extend the SP mask

Pull networking fixes from David Miller:

 1) Fix endless loop in nf_tables, from Phil Sutter.

 2) Fix cross namespace ip6_gre tunnel hash list corruption, from
    Olivier Matz.

 3) Don't be too strict in phy_start_aneg() otherwise we might not allow
    restarting auto negotiation. From Heiner Kallweit.

 4) Fix various KMSAN uninitialized value cases in tipc, from Ying Xue.

 5) Memory leak in act_tunnel_key, from Davide Caratti.

 6) Handle chip errata of mv88e6390 PHY, from Andrew Lunn.

 7) Remove linear SKB assumption in fou/fou6, from Eric Dumazet.

 8) Missing udplite rehash callbacks, from Alexey Kodanev.

 9) Log dirty pages properly in vhost, from Jason Wang.

10) Use consume_skb() in neigh_probe() as this is a normal free not a
    drop, from Yang Wei. Likewise in macvlan_process_broadcast().

11) Missing device_del() in mdiobus_register() error paths, from Thomas
    Petazzoni.

12) Fix checksum handling of short packets in mlx5, from Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (96 commits)
  bpf: in __bpf_redirect_no_mac pull mac only if present
  virtio_net: bulk free tx skbs
  net: phy: phy driver features are mandatory
  isdn: avm: Fix string plus integer warning from Clang
  net/mlx5e: Fix cb_ident duplicate in indirect block register
  net/mlx5e: Fix wrong (zero) TX drop counter indication for representor
  net/mlx5e: Fix wrong error code return on FEC query failure
  net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames
  tools: bpftool: Cleanup license mess
  bpf: fix inner map masking to prevent oob under speculation
  bpf: pull in pkt_sched.h header for tooling to fix bpftool build
  selftests: forwarding: Add a test case for externally learned FDB entries
  selftests: mlxsw: Test FDB offload indication
  mlxsw: spectrum_switchdev: Do not treat static FDB entries as sticky
  net: bridge: Mark FDB entries that were added by user as such
  mlxsw: spectrum_fid: Update dummy FID index
  mlxsw: pci: Return error on PCI reset timeout
  mlxsw: pci: Increase PCI SW reset timeout
  mlxsw: pci: Ring CQ's doorbell before RDQ's
  MAINTAINERS: update email addresses of liquidio driver maintainers
  ...

Yue Hu noticed that when parsing device tree the allocated platform data
was never freed. Since it's not used beyond the function scope, this
switches to using a stack variable instead.
Reported-by: Yue Hu <huyue2@yulong.com>
Fixes: 35da6094 ("pstore/ram: add Device Tree bindings")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>

GCC 9 reworks the way the references to the stack canary are
emitted, to prevent the value from being spilled to the stack
before the final comparison in the epilogue, defeating the
purpose, given that the spill slot is under control of the
attacker that we are protecting ourselves from.

Since our canary value address is obtained without accessing
memory (as opposed to pre-v7 code that will obtain it from a
literal pool), it is unlikely (although not guaranteed) that
the compiler will spill the canary value in the same way, so
let's just disable this improvement when building with GCC9+.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>

The ARM per-task stack protector GCC plugin hits an assert in
the compiler in some case, due to the fact the the SP mask
expression is not sign-extended as it should be. So fix that.
Suggested-by: Kugan Vivekanandarajah <kugan.vivekanandarajah@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>

Ido Schimmel says:

====================
mlxsw: spectrum_router: Add GRE tunnel support for Spectrum-2

Nir says:

In Spectrum-2, HW implementation of layer 3 tunnels differs from
Spectrum-1 when it comes to the underlay routing table selection.
Spectrum-2 uses a dedicated RIF that points to the virtual router used
for forwarding the encapsulated packets, while Spectrum-1 explicitly
specifies the virtual router itself.

Patches #1 and #2 add additional fields in RITR - Router interface table
register and RTDP - Routing tunnel decap properties respectively, the
fields are required for the new underlay RIF needed for Spectrum-2.

Patches #3-4 allow different set of RIF operations per ASIC type. The
first patch splits the operations and the following patch sets RIF ops
according to ASIC type.

Patches #5-9 introduce small changes to existing code to allow existence
of a dedicated underlay RIF along with the underlay virtual router, and
to support that new type of RIF that has no device.

Patch #10 takes care of updating the tunnel decap properties egress
underlay RIF required for Spectrum-2.

Patch #11 adds the implementation of Spectrum-2 specific RIF operations
and essentially enables layer 3 GRE tunnels on Spectrum-2.

Finally patches #12-18 add tests for GRE IP-in-IP tunnels, both in flat
and hierarchical topologies.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on hierarchical topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where a key is set. This test is based on hierarchical topology described
in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
based on hierarchical topology described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on flat topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where a key is set. This test is based on flat topology described in file
ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
based on flat topology described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>