Previously, the flow director counter is not enabled. To improve the
maintainability for chechking whether flow director hit or not, enable
flow director counter for each function, and add debugfs query inerface
to query the counters for each function.

The debugfs command is below:
cat fd_counter
func_id    hit_times
pf         0
vf0        0
vf1        0
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Menglong Dong says:

====================
net: tipc: fix FB_MTU eat two pages and do some code cleanup

In the first patch, FB_MTU is redefined to make sure data size will not
exceed PAGE_SIZE. Besides, I removed the alignment for buf_size in
tipc_buf_acquire, because skb_alloc_fclone will do the alignment job.

In the second patch, I removed align() in msg.c and replace it with
ALIGN().

Changes since V5:
- remove blank line after Fixes in commit log in the first patch

Changes since V4:
- remove ONE_PAGE_SKB_SZ and replace it with one_page_mtu in the first
  patch.
- fix some code style problems for the second patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The function align() which is defined in msg.c is redundant, replace it
with ALIGN() and introduce a BUF_ALIGN().
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FB_MTU is used in 'tipc_msg_build()' to alloc smaller skb when memory
allocation fails, which can avoid unnecessary sending failures.

The value of FB_MTU now is 3744, and the data size will be:

  (3744 + SKB_DATA_ALIGN(sizeof(struct skb_shared_info)) + \
    SKB_DATA_ALIGN(BUF_HEADROOM + BUF_TAILROOM + 3))

which is larger than one page(4096), and two pages will be allocated.

To avoid it, replace '3744' with a calculation:

  (PAGE_SIZE - SKB_DATA_ALIGN(BUF_OVERHEAD) - \
    SKB_DATA_ALIGN(sizeof(struct skb_shared_info)))

What's more, alloc_skb_fclone() will call SKB_DATA_ALIGN for data size,
and it's not necessary to make alignment for buf_size in
tipc_buf_acquire(). So, just remove it.

Fixes: 4c94cc2d ("tipc: fall back to smaller MTU if allocation of local send skb fails")
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

/klassert/ipsec-next

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2021-06-28

1) Remove an unneeded error assignment in esp4_gro_receive().
   From Yang Li.

2) Add a new byseq state hashtable to find acquire states faster.
   From Sabrina Dubroca.

3) Remove some unnecessary variables in pfkey_create().
   From zuoqilin.

4) Remove the unused description from xfrm_type struct.
   From Florian Westphal.

5) Fix a spelling mistake in the comment of xfrm_state_ok().
   From gushengxian.

6) Replace hdr_off indirections by a small helper function.
   From Florian Westphal.

7) Remove xfrm4_output_finish and xfrm6_output_finish declarations,
   they are not used anymore.From Antony Antony.

8) Remove xfrm replay indirections.
   From Florian Westphal.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-net-next-2021-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes berg says:

====================
Lots of changes:
 * aggregation handling improvements for some drivers
 * hidden AP discovery on 6 GHz and other HE 6 GHz
   improvements
 * minstrel improvements for no-ack frames
 * deferred rate control for TXQs to improve reaction
   times
 * virtual time-based airtime scheduler
 * along with various little cleanups/fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Dan Carpenter reported an issue introduced in
commit fde56eea ("mptcp: refine mptcp_cleanup_rbuf") where a new
boolean (ack_pending) is masked with 0x9.

This is not the intention to ignore values by using a boolean. This
variable should not have a 'bool' type: we should keep the 'u8' to allow
this comparison.

Fixes: fde56eea ("mptcp: refine mptcp_cleanup_rbuf")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Guillaume Nault says:

====================
net: reset MAC header consistently across L3 virtual devices

Some virtual L3 devices, like vxlan-gpe and gre (in collect_md mode),
reset the MAC header pointer after they parsed the outer headers. This
accurately reflects the fact that the decapsulated packet is pure L3
packet, as that makes the MAC header 0 bytes long (the MAC and network
header pointers are equal).

However, many L3 devices only adjust the network header after
decapsulation and leave the MAC header pointer to its original value.
This can confuse other parts of the networking stack, like TC, which
then considers the outer headers as one big MAC header.

This patch series makes the following L3 tunnels behave like VXLAN-GPE:
bareudp, ipip, sit, gre, ip6gre, ip6tnl, gtp.

The case of gre is a bit special. It already resets the MAC header
pointer in collect_md mode, so only the classical mode needs to be
adjusted. However, gre also has a special case that expects the MAC
header pointer to keep pointing to the outer header even after
decapsulation. Therefore, patch 4 keeps an exception for this case.

Ideally, we'd centralise the call to skb_reset_mac_header() in
ip_tunnel_rcv(), to avoid manual calls in ipip (patch 2),
sit (patch 3) and gre (patch 4). That's unfortunately not feasible
currently, because of the gre special case discussed above that
precludes us from resetting the MAC header unconditionally.

The original motivation is to redirect bareudp packets to Ethernet
devices (as described in patch 1). The rest of this series aims at
bringing consistency across all L3 devices (apart from gre's special
case unfortunately).

Note: the gtp patch results from pure code inspection and has been
compiled tested only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For consistency with other L3 tunnel devices, reset the mac_header
pointer after decapsulation. This makes the mac_header 0 bytes long,
thus making it clear that this skb has no mac_header.

Compile tested only.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reset the mac_header pointer even when the tunnel transports only L3
data (in the ARPHRD_ETHER case, this is already done by eth_type_trans).
This prevents other parts of the stack from mistakenly accessing the
outer header after the packet has been decapsulated.

In practice, this allows to push an Ethernet header to ipip6, ip6ip6,
mplsip6 or ip6gre packets and redirect them to an Ethernet device:

  $ tc filter add dev ip6tnl0 ingress matchall       \
      action vlan push_eth dst_mac 00:00:5e:00:53:01 \
                           src_mac 00:00:5e:00:53:00 \
      action mirred egress redirect dev eth0

Without this patch, push_eth refuses to add an ethernet header because
the skb appears to already have a MAC header.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit e271c7b4 ("gre: do not keep the GRE header around in collect
medata mode") did reset the mac_header for the collect_md case. Let's
extend this behaviour to classical gre devices as well.

ipgre_header_parse() seems to be the only case that requires mac_header
to point to the outer header. We can detect this case accurately by
checking ->header_ops. For all other cases, we can reset mac_header.

This allows to push an Ethernet header to ipgre packets and redirect
them to an Ethernet device:

  $ tc filter add dev gre0 ingress matchall          \
      action vlan push_eth dst_mac 00:00:5e:00:53:01 \
                           src_mac 00:00:5e:00:53:00 \
      action mirred egress redirect dev eth0

Before this patch, this worked only for collect_md gre devices.
Now this works for regular gre devices as well. Only the special case
of gre devices that use ipgre_header_ops isn't supported.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even though sit transports L3 data (IPv6, IPv4 or MPLS) packets, it
needs to reset the mac_header pointer, so that other parts of the stack
don't mistakenly access the outer header after the packet has been
decapsulated. There are two rx handlers to modify: ipip6_rcv() for the
ip6ip mode and sit_tunnel_rcv() which is used to re-implement the ipip
and mplsip modes of ipip.ko.

This allows to push an Ethernet header to sit packets and redirect
them to an Ethernet device:

  $ tc filter add dev sit0 ingress matchall          \
      action vlan push_eth dst_mac 00:00:5e:00:53:01 \
                           src_mac 00:00:5e:00:53:00 \
      action mirred egress redirect dev eth0

Without this patch, push_eth refuses to add an ethernet header because
the skb appears to already have a MAC header.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even though ipip transports IPv4 or MPLS packets, it needs to reset the
mac_header pointer, so that other parts of the stack don't mistakenly
access the outer header after the packet has been decapsulated.

This allows to push an Ethernet header to ipip or mplsip packets and
redirect them to an Ethernet device:

  $ tc filter add dev ipip0 ingress matchall         \
      action vlan push_eth dst_mac 00:00:5e:00:53:01 \
                           src_mac 00:00:5e:00:53:00 \
      action mirred egress redirect dev eth0

Without this patch, push_eth refuses to add an ethernet header because
the skb appears to already have a MAC header.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even though bareudp transports L3 data (typically IP or MPLS), it needs
to reset the mac_header pointer, so that other parts of the stack don't
mistakenly access the outer header after the packet has been
decapsulated.

This allows to push an Ethernet header to bareudp packets and redirect
them to an Ethernet device:

  $ tc filter add dev bareudp0 ingress matchall      \
      action vlan push_eth dst_mac 00:00:5e:00:53:01 \
                           src_mac 00:00:5e:00:53:00 \
      action mirred egress redirect dev eth0

Without this patch, push_eth refuses to add an ethernet header because
the skb appears to already have a MAC header.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2021-06-25

This series contains updates to ice driver only.

Jesse adds support for tracepoints to aide in debugging.

Maciej adds support for PTP auxiliary pin support.

Victor removes the VSI info from the old aggregator when moving the VSI
to another aggregator.

Tony removes an unnecessary VSI assignment.

Christophe Jaillet fixes a memory leak for failed allocation in
ice_pf_dcb_cfg().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When smc_sendmsg() is called before the SMC socket initialization has
completed, smc_tx_sendmsg() will access un-initialized fields of the
SMC socket which results in a null-pointer dereference.
Fix this by checking the socket state first in smc_tx_sendmsg().

Fixes: e0e4b8fa ("net/smc: Add SMC statistics support")
Reported-by: syzbot+5dda108b672b54141857@syzkaller.appspotmail.com
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-2021-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.14

Second, and most likely the last, set of patches for v5.14. mt76 and
iwlwifi have most patches in this round, but rtw88 also has some new
features. Nothing special really standing out.

mt76

* mt7915 MSI support

* disable ASPM on mt7915

* mt7915 tx status reporting

* mt7921 decap offload

rtw88

* beacon filter support

* path diversity support

* firmware crash information via devcoredump

* quirks for disabling pci capabilities

mt7601u

* add USB ID for a XiaoDu WiFi Dongle

ath11k

* enable support for QCN9074 PCI devices

brcmfmac

* support parse country code map from DeviceTree

iwlwifi

* support for new hardware

* support for BIOS control of 11ax enablement in Russia

* support UNII4 band enablement from BIOS
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The newly implemented fwnode_mdbiobus_register turned out to be
problematic - in case the fwnode_/of_/acpi_mdio are built as
modules, a dependency cycle can be observed during the depmod phase of
modules_install, eg.:

depmod: ERROR: Cycle detected: fwnode_mdio -> of_mdio -> fwnode_mdio
depmod: ERROR: Found 2 modules in dependency cycles!

OR:

depmod: ERROR: Cycle detected: acpi_mdio -> fwnode_mdio -> acpi_mdio
depmod: ERROR: Found 2 modules in dependency cycles!

A possible solution could be to rework fwnode_mdiobus_register,
so that to merge the contents of acpi_mdiobus_register and
of_mdiobus_register. However feasible, such change would
be very intrusive and affect huge amount of the of_mdiobus_register
users.

Since there are currently 2 users of ACPI and MDIO
(xgmac_mdio and mvmdio), withdraw the fwnode_mdbiobus_register
and roll back to a simple 'if' condition in affected drivers.

Fixes: 62a6ef6a ("net: mdiobus: Introduce fwnode_mdbiobus_register()")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If this 'kzalloc()' fails we must free some resources as in all the other
error handling paths of this function.

Fixes: 348048e7 ("ice: Implement iidc operations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

ice_get_vf_vsi() is being called twice for the same VSI. Remove the
unnecessary call/assignment.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>

Remove the VSI info from previous aggregator after moving the VSI to a
new aggregator.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The E810 device supports programmable pins for enabling both input and
output events related to the PTP hardware clock. This includes both
output signals with programmable period, as well as timestamping of
events on input pins.

Add support for enabling these using the CONFIG_PTP_1588_CLOCK
interface.

This allows programming the software defined pins to take advantage of
the hardware clock features.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

This patch adds build and driver logic for the "mlxbf_gige"
Ethernet driver from Mellanox Technologies. The second
generation BlueField SoC from Mellanox supports an
out-of-band GigaBit Ethernet management port to the Arm
subsystem.  This driver supports TCP/IP network connectivity
for that port, and provides back-end routines to handle
basic ethtool requests.

The driver interfaces to the Gigabit Ethernet block of
BlueField SoC via MMIO accesses to registers, which contain
control information or pointers describing transmit and
receive resources.  There is a single transmit queue, and
the port supports transmit ring sizes of 4 to 256 entries.
There is a single receive queue, and the port supports
receive ring sizes of 32 to 32K entries. The transmit and
receive rings are allocated from DMA coherent memory. There
is a 16-bit producer and consumer index per ring to denote
software ownership and hardware ownership, respectively.

The main driver logic such as probe(), remove(), and netdev
ops are in "mlxbf_gige_main.c".  Logic in "mlxbf_gige_rx.c"
and "mlxbf_gige_tx.c" handles the packet processing for
receive and transmit respectively.

The logic in "mlxbf_gige_ethtool.c" supports the handling
of some basic ethtool requests: get driver info, get ring
parameters, get registers, and get statistics.

The logic in "mlxbf_gige_mdio.c" is the driver controlling
the Mellanox BlueField hardware that interacts with a PHY
device via MDIO/MDC pins.  This driver does the following:
  - At driver probe time, it configures several BlueField MDIO
    parameters such as sample rate, full drive, voltage and MDC
  - It defines functions to read and write MDIO registers and
    registers the MDIO bus.
  - It defines the phy interrupt handler reporting a
    link up/down status change
  - This driver's probe is invoked from the main driver logic
    while the phy interrupt handler is registered in ndo_open.

Driver limitations
  - Only supports 1Gbps speed
  - Only supports GMII protocol
  - Supports maximum packet size of 2KB
  - Does not support scatter-gather buffering

Testing
  - Successful build of kernel for ARM64, ARM32, X86_64
  - Tested ARM64 build on FastModels & Palladium
  - Tested ARM64 build on several Mellanox boards that are built with
    the BlueField-2 SoC.  The testing includes coverage in the areas
    of networking (e.g. ping, iperf, ifconfig, route), file transfers
    (e.g. SCP), and various ethtool options relevant to this driver.
Signed-off-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Liming Sun <limings@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is modeled after one by Scott Peterson for i40e.

Add tracepoints to the driver, via a new file ice_trace.h and some new
trace calls added in interesting places in the driver. Add some tracing
for DIMLIB to help debug interrupt moderation problems.

Performance should not be affected, and this can be very useful
for debugging and adding new trace events to paths in the future.

Note eBPF programs can attach to these events, as well as perf
can count them since we're attaching to the events subsystem
in the kernel.
Co-developed-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The Broadcom UniMAC MDIO bus from mdio-bcm-unimac module comes too late.
So, GENET cannot find the ethernet PHY on UniMAC MDIO bus. This leads
GENET fail to attach the PHY as following log:

bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
...
could not attach to PHY
bcmgenet fd580000.ethernet eth0: failed to connect to PHY
uart-pl011 fe201000.serial: no DMA platform data
libphy: bcmgenet MII bus: probed
...
unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus

It is not just coming too late, there is also no way for the module
loader to figure out the dependency between GENET and its MDIO bus
driver unless we provide this MODULE_SOFTDEP hint.

This patch adds the soft dependency to load mdio-bcm-unimac module
before genet module to fix this issue.

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=213485
Fixes: 9a4e7969 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

parameter dst always points to null.
Signed-off-by: zhang kai <zhangkaiheb@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simply get a pointer to the data in the register payload instead of
copying it to a temporary buffer.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

https://patchwork.kernel.org/project/netdevbpf/list/?series=506637&state=*

- Remove unused variable
- Use correct integer type for string formatting.
- Remove `inline` in C files

Fixes: 9c1a59a2 ("gve: DQO: Add ring allocation and initialization")
Fixes: a57e5de4 ("gve: DQO: Add TX path")
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: make the PLPMTUD probe more effective and efficient

As David Laight noticed, it currently takes quite some time to find
the optimal pmtu in the Search state, and also lacks the black hole
detection in the Search Complete state. This patchset is to address
them to mke the PLPMTUD probe more effective and efficient.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

These is no need to wait for 'interval' period for the next probe
if the last probe is already acked in search state. The 'interval'
period waiting should be only for probe failure timeout and the
current pmtu check when it's in search complete state.

This change will shorten the probe time a lot in search state, and
also fix the document accordingly.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the PLPMUTD probe will stop for a long period (interval * 30)
after it enters search complete state. If there's a pmtu change on the
route path, it takes a long time to be aware if the ICMP TooBig packet
is lost or filtered.

As it says in rfc8899#section-4.3:

  "A DPLPMTUD method MUST NOT rely solely on this method."
  (ICMP PTB message).

This patch is to enable the other method for search complete state:

  "A PL can use the DPLPMTUD probing mechanism to periodically
   generate probe packets of the size of the current PLPMTU."

With this patch, the probe will continue with the current pmtu every
'interval' until the PMTU_RAISE_TIMER 'timeout', which we implement
by adding raise_count to raise the probe size when it counts to 30
and removing the SCTP_PL_COMPLETE check for PMTU_RAISE_TIMER.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Document the NXP SJA1110 switch as supported

Now that most of the basic work for SJA1110 support has been done in the
sja1105 DSA driver, let's add the missing documentation bits to make it
clear that the driver can be used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Mention support for the SJA1110 in menuconfig.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Denote that the new switch generation is supported, detail its pin
strapping options (with differences compared to SJA1105) and explain how
MDIO access to the internal 100base-T1 and 100base-TX PHYs is performed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bailey Forrest says:

====================
gve: Introduce DQO descriptor format

DQO is the descriptor format for our next generation virtual NIC. The existing
descriptor format will be referred to as "GQI" in the patch set.

One major change with DQO is it uses dual descriptor rings for both TX and RX
queues.

The TX path uses a TX queue to send descriptors to HW, and receives packet
completion events on a TX completion queue.

The RX path posts buffers to HW using an RX buffer queue and receives incoming
packets on an RX queue.

One important note is that DQO descriptors and doorbells are little endian. We
continue to use the existing big endian control plane infrastructure.

The general format of the patch series is:
- Refactor existing code/data structures to be shared by DQO
- Expand admin queues to support DQO device setup
- Expand data structures and device setup to support DQO
- Add logic to setup DQO queues
- Implement datapath
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The RX queue has an array of `gve_rx_buf_state_dqo` objects. All
allocated pages have an associated buf_state object. When a buffer is
posted on the RX buffer queue, the buffer ID will be the buf_state's
index into the RX queue's array.

On packet reception, the RX queue will have one descriptor for each
buffer associated with a received packet. Each RX descriptor will have
a buffer_id that was posted on the buffer queue.

Notable mentions:

- We use a default buffer size of 2048 bytes. Based on page size, we
  may post separate sections of a single page as separate buffers.

- The driver holds an extra reference on pages passed up the receive
  path with an skb and keeps these pages on a list. When posting new
  buffers to the NIC, we check if any of these pages has only our
  reference, or another buffer sized segment of the page has no
  references. If so, it is free to reuse. This page recycling approach
  is a common netdev optimization that reduces page alloc/free calls.

- Pages in the free list have a page_count bias in order to avoid an
  atomic increment of pagecount every time we attempt to reuse a page.
  # references = page_count() - bias

- In order to track when a page is safe to reuse, we keep track of the
  last offset which had a single SKB reference. When this occurs, it
  implies that every single other offset is reusable. Otherwise, we
  don't know if offsets can be safely reused.

- We maintain two free lists of pages. List #1 (recycled_buf_states)
  contains pages we know can be reused right away. List #2
  (used_buf_states) contains pages which cannot be used right away. We
  only attempt to get pages from list #2 when list #1 is empty. We only
  attempt to use a small fixed number pages from list #2 before giving
  up and allocating a new page. Both lists are FIFOs in hope that by the
  time we attempt to reuse a page, the references were dropped.
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TX SKBs will have their buffers DMA mapped with the device. Each buffer
will have at least one TX descriptor associated. Each SKB will also have
a metadata descriptor.

Each TX queue maintains an array of `gve_tx_pending_packet_dqo` objects.
Every TX SKB will have an associated pending_packet object. A TX SKB's
descriptors will use its pending_packet's index as the completion tag,
which will be returned on the TX completion queue.

The device implements a "flow-miss model". Most packets will simply
receive a packet completion. The flow-miss system may choose to process
a packet based on its contents. A TX packet which experiences a flow
miss would receive a miss completion followed by a later reinjection
completion. The miss-completion is received when the packet starts to be
processed by the flow-miss system and the reinjection completion is
received when the flow-miss system completes processing the packet and
sends it on the wire.

Notable mentions:

- Buffers may be freed after receiving the miss-completion, but in order
  to avoid packet reordering, we do not complete the SKB until receiving
  the reinjection completion.

- The driver must robustly handle the unlikely scenario where a miss
  completion does not have an associated reinjection completion. This is
  accomplished by maintaining a list of packets which have a pending
  reinjection completion. After a short timeout (5 seconds), the
  SKB and buffers are released and the pending_packet is moved to a
  second list which has a longer timeout (60 seconds), where the
  pending_packet will not be reused. When the longer timeout elapses,
  the driver may assume the reinjection completion would never be
  received and the pending_packet may be reused.

- Completion handling is triggered by an interrupt and is done in the
  NAPI poll function. Because the TX path and completion exist in
  different threading contexts they maintain their own lists for free
  pending_packet objects. The TX path uses a lock-free approach to steal
  the list from the completion path.

- Both the TSO context and general context descriptors have metadata
  bytes. The device requires that if multiple descriptors contain the
  same field, each descriptor must have the same value set for that
  field.
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When interrupts are first enabled, we also set the ratelimits, which
will be static for the entire usage of the device.
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocate the buffer and completion ring structures. Do not populate the
rings yet. That will happen in the respective rx and tx datapath
follow-on patches
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add napi netdev device registration, interrupt handling and initial tx
and rx polling stubs. The stubs will be filled in follow-on patches.

Also:
- LRO feature advertisement and handling
- Also update ethtool logic
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>