- 26 Jul, 2019 40 commits
-
-
Krzysztof Kozlowski authored
commit 16da0eb5 upstream. On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750 mV, not 600 mV. Using wrong minimal value caused shifting of these regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was reported as 1.2 V). On most of the boards these regulators are left in default state so this was only affecting reported voltage. However if any driver wanted to change them, then effectively it would set voltage 150 mV higher than intended. Cc: <stable@vger.kernel.org> Fixes: cb74685e ("regulator: s2mps11: Add samsung s2mps11 regulator driver") Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Hui Wang authored
commit 771a081e upstream. In the function alps_is_cs19_trackpoint(), we check if the param[1] is in the 0x20~0x2f range, but the code we wrote for this checking is not correct: (param[1] & 0x20) does not mean param[1] is in the range of 0x20~0x2f, it also means the param[1] is in the range of 0x30~0x3f, 0x60~0x6f... Now fix it with a new condition checking ((param[1] & 0xf0) == 0x20). Fixes: 7e4935cc ("Input: alps - don't handle ALPS cs19 trackpoint-only device") Cc: stable@vger.kernel.org Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Nick Black authored
commit 1976d7d2 upstream. Adds the Lenovo T580 to the SMBus intertouch list for Synaptics touchpads. I've tested with this for a week now, and it seems a great improvement. It's also nice to have the complaint gone from dmesg. Signed-off-by:
Nick Black <dankamongmen@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Hui Wang authored
commit 7e4935cc upstream. On a latest Lenovo laptop, the trackpoint and 3 buttons below it don't work at all, when we move the trackpoint or press those 3 buttons, the kernel will print out: "Rejected trackstick packet from non DualPoint device" This device is identified as an alps touchpad but the packet has trackpoint format, so the alps.c drops the packet and prints out the message above. According to XiaoXiao's explanation, this device is named cs19 and is trackpoint-only device, its firmware is only for trackpoint, it is independent of touchpad and is a device completely different from DualPoint ones. To drive this device with mininal changes to the existing driver, we just let the alps driver not handle this device, then the trackpoint.c will be the driver of this device if the trackpoint driver is enabled. (if not, this device will fallback to a bare PS/2 device) With the trackpoint.c, this trackpoint and 3 buttons all work well, they have all features that the trackpoint should have, like scrolling-screen, drag-and-drop and frame-selection. Signed-off-by:
XiaoXiao Liu <sliuuxiaonxiao@gmail.com> Signed-off-by:
Pali Rohár <pali.rohar@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Grant Hernandez authored
commit 2a017fd8 upstream. The GTCO tablet input driver configures itself from an HID report sent via USB during the initial enumeration process. Some debugging messages are generated during the parsing. A debugging message indentation counter is not bounds checked, leading to the ability for a specially crafted HID report to cause '-' and null bytes be written past the end of the indentation array. As long as the kernel has CONFIG_DYNAMIC_DEBUG enabled, this code will not be optimized out. This was discovered during code review after a previous syzkaller bug was found in this driver. Signed-off-by:
Grant Hernandez <granthernandez@google.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Coly Li authored
commit f54d801d upstream. Commit 9baf3097 ("bcache: fix for gc and write-back race") added a new work queue dc->writeback_write_wq, but forgot to destroy it in the error condition when creating dc->writeback_thread failed. This patch destroys dc->writeback_write_wq if kthread_create() returns error pointer to dc->writeback_thread, then a memory leak is avoided. Fixes: 9baf3097 ("bcache: fix for gc and write-back race") Signed-off-by:
Coly Li <colyli@suse.de> Cc: stable@vger.kernel.org Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Coly Li authored
commit 54619998 upstream. In bch_cached_dev_files[] from driver/md/bcache/sysfs.c, sysfs_errors is incorrectly inserted in. The correct entry should be sysfs_io_errors. This patch fixes the problem and now I/O errors of cached device can be read from /sys/block/bcache<N>/bcache/io_errors. Fixes: c7b7bd07 ("bcache: add io_disable to struct cached_dev") Signed-off-by:
-
Coly Li authored
commit 578df99b upstream. When md raid device (e.g. raid456) is used as backing device, read-ahead requests on a degrading and recovering md raid device might be failured immediately by md raid code, but indeed this md raid array can still be read or write for normal I/O requests. Therefore such failed read-ahead request are not real hardware failure. Further more, after degrading and recovering accomplished, read-ahead requests will be handled by md raid array again. For such condition, I/O failures of read-ahead requests don't indicate real health status (because normal I/O still be served), they should not be counted into I/O error counter dc->io_errors. Since there is no simple way to detect whether the backing divice is a md raid device, this patch simply ignores I/O failures for read-ahead bios on backing device, to avoid bogus backing device failure on a degrading md raid array. Suggested-and-tested-by:
Thorsten Knabe <linux@thorsten-knabe.de> Signed-off-by:
-
Coly Li authored
commit ba82c1ac upstream. This reverts commit 6268dc2c. This patch depends on commit c4dc2497 ("bcache: fix high CPU occupancy during journal") which is reverted in previous patch. So revert this one too. Fixes: 6268dc2c ("bcache: free heap cache_set->flush_btree in bch_journal_free") Signed-off-by:
-
Coly Li authored
commit 249a5f6d upstream. This reverts commit c4dc2497. This patch enlarges a race between normal btree flush code path and flush_btree_write(), which causes deadlock when journal space is exhausted. Reverts this patch makes the race window from 128 btree nodes to only 1 btree nodes. Fixes: c4dc2497 ("bcache: fix high CPU occupancy during journal") Signed-off-by:
-
Coly Li authored
commit 695277f1 upstream. This reverts commit 6147305c. Although this patch helps the failed bcache device to stop faster when too many I/O errors detected on corresponding cached device, setting CACHE_SET_IO_DISABLE bit to cache set c->flags was not a good idea. This operation will disable all I/Os on cache set, which means other attached bcache devices won't work neither. Without this patch, the failed bcache device can also be stopped eventually if internal I/O accomplished (e.g. writeback). Therefore here I revert it. Fixes: 6147305c ("bcache: set CACHE_SET_IO_DISABLE in bch_cached_dev_error()") Reported-by:
Yong Li <mr.liyong@qq.com> Signed-off-by:
-
Wen Yang authored
commit 95566aa7 upstream. There is a possible double free issue in ppc4xx_trng_probe(): 85: dev->trng_base = of_iomap(trng, 0); 86: of_node_put(trng); ---> released here 87: if (!dev->trng_base) 88: goto err_out; ... 110: ierr_out: 111: of_node_put(trng); ---> double released here ... This issue was detected by using the Coccinelle software. We fix it by removing the unnecessary of_node_put(). Fixes: 5343e674 ("crypto4xx: integrate ppc4xx-rng into crypto4xx") Signed-off-by:
Wen Yang <wen.yang99@zte.com.cn> Cc: <stable@vger.kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Allison Randal <allison@lohutok.net> Cc: Armijn Hemel <armijn@tjaldur.nl> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: linux-crypto@vger.kernel.org Cc: linux-kernel@vger.kernel.org Acked-by:
Julia Lawall <julia.lawall@lip6.fr> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Cfir Cohen authored
commit 538a5a07 upstream. Avoid leaking GCM tag through timing side channel. Fixes: 36cf515b ("crypto: ccp - Enable support for AES GCM on v5 CCPs") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by:
Cfir Cohen <cfir@google.com> Acked-by:
Gary R Hook <ghook@amd.com> Signed-off-by:
-
Hook, Gary authored
commit 20e833dc upstream. The AES GCM function reuses an 'op' data structure, which members contain values that must be cleared for each (re)use. This fix resolves a crypto self-test failure: alg: aead: gcm-aes-ccp encryption test failed (wrong result) on test vector 2, cfg="two even aligned splits" Fixes: 36cf515b ("crypto: ccp - Enable support for AES GCM on v5 CCPs") Cc: <stable@vger.kernel.org> Signed-off-by:
Gary R Hook <gary.hook@amd.com> Signed-off-by:
-
Christian Lamparter authored
commit 0f7a8137 upstream. The hardware automatically zero pads incomplete block ciphers blocks without raising any errors. This is a screw-up. This was noticed by CONFIG_CRYPTO_MANAGER_EXTRA_TESTS tests that sent a incomplete blocks and expect them to fail. This fixes: cbc-aes-ppc4xx encryption unexpectedly succeeded on test vector "random: len=2409 klen=32"; expected_error=-22, cfg="random: may_sleep use_digest src_divs=[96.90%@+2295, 2.34%@+4066, 0.32%@alignmask+12, 0.34%@+4087, 0.9%@alignmask+1787, 0.1%@+3767] iv_offset=6" ecb-aes-ppc4xx encryption unexpectedly succeeded on test vector "random: len=1011 klen=32"; expected_error=-22, cfg="random: may_sleep use_digest src_divs=[100.0%@alignmask+20] dst_divs=[3.12%@+3001, 96.88%@+4070]" Cc: Eric Biggers <ebiggers@kernel.org> Cc: stable@vger.kernel.org [4.19, 5.0 and 5.1] Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Christian Lamparter authored
commit 70c4997f upstream. While the hardware consider them to be blockciphers, the reference implementation defines them as streamciphers. Do the right thing and set the blocksize to 1. This was found by CONFIG_CRYPTO_MANAGER_EXTRA_TESTS. This fixes the following issues: skcipher: blocksize for ofb-aes-ppc4xx (16) doesn't match generic impl (1) skcipher: blocksize for cfb-aes-ppc4xx (16) doesn't match generic impl (1) Cc: Eric Biggers <ebiggers@kernel.org> Cc: stable@vger.kernel.org Fixes: f2a13e7c ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads") Signed-off-by:
-
Christian Lamparter authored
commit bfa2ba7d upstream. This patch fixes a issue with crypto4xx's ctr(aes) that was discovered by libcapi's kcapi-enc-test.sh test. The some of the ctr(aes) encryptions test were failing on the non-power-of-two test: kcapi-enc - Error: encryption failed with error 0 kcapi-enc - Error: decryption failed with error 0 [FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits): original file (1d100e..cc96184c) and generated file (e3b0c442..1b7852b855) [FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits) (openssl generated CT): original file (e3b0..5) and generated file (3..8e) [PASSED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits) (openssl generated PT) [FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (password): original file (1d1..84c) and generated file (e3b..852b855) But the 16, 32, 512, 65536 tests always worked. Thankfully, this isn't a hidden hardware problem like previously, instead this turned out to be a copy and paste issue. With this patch, all the tests are passing with and kcapi-enc-test.sh gives crypto4xx's a clean bill of health: "Number of failures: 0" :). Cc: stable@vger.kernel.org Fixes: 98e87e3d ("crypto: crypto4xx - add aes-ctr support") Fixes: f2a13e7c ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads") Signed-off-by:
-
Eric Biggers authored
commit 7545b6c2 upstream. Clear the CRYPTO_TFM_REQ_MAY_SLEEP flag when the chacha20poly1305 operation is being continued from an async completion callback, since sleeping may not be allowed in that context. This is basically the same bug that was recently fixed in the xts and lrw templates. But, it's always been broken in chacha20poly1305 too. This was found using syzkaller in combination with the updated crypto self-tests which actually test the MAY_SLEEP flag now. Reproducer: python -c 'import socket; socket.socket(socket.AF_ALG, 5, 0).bind( ("aead", "rfc7539(cryptd(chacha20-generic),poly1305-generic)"))' Kernel output: BUG: sleeping function called from invalid context at include/crypto/algapi.h:426 in_atomic(): 1, irqs_disabled(): 0, pid: 1001, name: kworker/2:2 [...] CPU: 2 PID: 1001 Comm: kworker/2:2 Not tainted 5.2.0-rc2 #5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-20181126_142135-anatol 04/01/2014 Workqueue: crypto cryptd_queue_worker Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x4d/0x6a lib/dump_stack.c:113 ___might_sleep kernel/sched/core.c:6138 [inline] ___might_sleep.cold.19+0x8e/0x9f kernel/sched/core.c:6095 crypto_yield include/crypto/algapi.h:426 [inline] crypto_hash_walk_done+0xd6/0x100 crypto/ahash.c:113 shash_ahash_update+0x41/0x60 crypto/shash.c:251 shash_async_update+0xd/0x10 crypto/shash.c:260 crypto_ahash_update include/crypto/hash.h:539 [inline] poly_setkey+0xf6/0x130 crypto/chacha20poly1305.c:337 poly_init+0x51/0x60 crypto/chacha20poly1305.c:364 async_done_continue crypto/chacha20poly1305.c:78 [inline] poly_genkey_done+0x15/0x30 crypto/chacha20poly1305.c:369 cryptd_skcipher_complete+0x29/0x70 crypto/cryptd.c:279 cryptd_skcipher_decrypt+0xcd/0x110 crypto/cryptd.c:339 cryptd_queue_worker+0x70/0xa0 crypto/cryptd.c:184 process_one_work+0x1ed/0x420 kernel/workqueue.c:2269 worker_thread+0x3e/0x3a0 kernel/workqueue.c:2415 kthread+0x11f/0x140 kernel/kthread.c:255 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352 Fixes: 71ebc4d1 ("crypto: chacha20poly1305 - Add a ChaCha20-Poly1305 AEAD construction, RFC7539") Cc: <stable@vger.kernel.org> # v4.2+ Cc: Martin Willi <martin@strongswan.org> Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
-
Elena Petrova authored
commit 6bd934de upstream. The sha256-ce finup implementation for ARM64 produces wrong digest for empty input (len=0). Expected: the actual digest, result: initial value of SHA internal state. The error is in sha256_ce_finup: for empty data `finalize` will be 1, so the code is relying on sha2_ce_transform to make the final round. However, in sha256_base_do_update, the block function will not be called when len == 0. Fix it by setting finalize to 0 if data is empty. Fixes: 03802f6a ("crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer") Cc: stable@vger.kernel.org Signed-off-by:
Elena Petrova <lenaptr@google.com> Reviewed-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
-
Elena Petrova authored
commit 1d4aaf16 upstream. The sha1-ce finup implementation for ARM64 produces wrong digest for empty input (len=0). Expected: da39a3ee..., result: 67452301... (initial value of SHA internal state). The error is in sha1_ce_finup: for empty data `finalize` will be 1, so the code is relying on sha1_ce_transform to make the final round. However, in sha1_base_do_update, the block function will not be called when len == 0. Fix it by setting finalize to 0 if data is empty. Fixes: 07eb54d3 ("crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer") Cc: stable@vger.kernel.org Signed-off-by:
-
Hook, Gary authored
commit 52393d61 upstream. The error code read from the queue status register is only 6 bits wide, but we need to verify its value is within range before indexing the error messages. Fixes: 81422bad ("crypto: ccp - Make syslog errors human-readable") Cc: <stable@vger.kernel.org> Reported-by:
-
Eric Biggers authored
commit 5c6bc4df upstream. Changing ghash_mod_init() to be subsys_initcall made it start running before the alignment fault handler has been installed on ARM. In kernel builds where the keys in the ghash test vectors happened to be misaligned in the kernel image, this exposed the longstanding bug that ghash_setkey() is incorrectly casting the key buffer (which can have any alignment) to be128 for passing to gf128mul_init_4k_lle(). Fix this by memcpy()ing the key to a temporary buffer. Don't fix it by setting an alignmask on the algorithm instead because that would unnecessarily force alignment of the data too. Fixes: 2cdc6899 ("crypto: ghash - Add GHASH digest algorithm for GCM") Reported-by:
Peter Robinson <pbrobinson@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Finn Thain authored
commit 78ff751f upstream. A system bus error during a PDMA transfer can mess up the calculation of the transfer residual (the PDMA handshaking hardware lacks a byte counter). This results in data corruption. The algorithm in this patch anticipates a bus error by starting each transfer with a MOVE.B instruction. If a bus error is caught the transfer will be retried. If a bus error is caught later in the transfer (for a MOVE.W instruction) the transfer gets failed and subsequent requests for that target will use PIO instead of PDMA. This avoids the "!REQ and !ACK" error so the severity level of that message is reduced to KERN_DEBUG. Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: stable@vger.kernel.org # v4.14+ Fixes: 3a0f64bf ("mac_scsi: Fix pseudo DMA implementation") Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Reported-by:
Chris Jones <chris@martin-jones.com> Tested-by:
Stan Johnson <userm57@yahoo.com> Tested-by:
Michael Schmitz <schmitzmic@gmail.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Finn Thain authored
commit 7398cee4 upstream. Some targets introduce delays when handshaking the response to certain commands. For example, a disk may send a 96-byte response to an INQUIRY command (or a 24-byte response to a MODE SENSE command) too slowly. Apparently the first 12 or 14 bytes are handshaked okay but then the system bus error timeout is reached while transferring the next word. Since the scsi bus phase hasn't changed, the driver then sets the target borken flag to prevent further PDMA transfers. The driver also logs the warning, "switching to slow handshake". Raise the PDMA threshold to 512 bytes so that PIO transfers will be used for these commands. This default is sufficiently low that PDMA will still be used for READ and WRITE commands. The existing threshold (16 bytes) was chosen more or less at random. However, best performance requires the threshold to be as low as possible. Those systems that don't need the PIO workaround at all may benefit from mac_scsi.setup_use_pdma=1 Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org # v4.14+ Fixes: 3a0f64bf ("mac_scsi: Fix pseudo DMA implementation") Signed-off-by:
-
Shivasharan S authored
commit c8f96df5 upstream. In megasas_get_target_prop(), driver is incorrectly calculating the target ID for devices with channel 1 and 3. Due to this, firmware will either fail the command (if there is no device with the target id sent from driver) or could return the properties for a target which was not intended. Devices could end up with the wrong queue depth due to this. Fix target id calculation for channel 1 and 3. Fixes: 96188a89 ("scsi: megaraid_sas: NVME interface target prop added") Cc: stable@vger.kernel.org Signed-off-by:
Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by:
-
Ming Lei authored
commit f9b0530f upstream. When scsi_init_sense_cache(host) is called concurrently from different hosts, each code path may find that no cache has been created and allocate a new one. The lack of locking can lead to potentially overriding a cache allocated by a different host. Fix the issue by moving 'mutex_lock(&scsi_sense_cache_mutex)' before scsi_select_sense_cache(). Fixes: 0a6ac4ee ("scsi: respect unchecked_isa_dma for blk-mq") Cc: Stable <stable@vger.kernel.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Ewan D. Milne <emilne@redhat.com> Signed-off-by:
Ming Lei <ming.lei@redhat.com> Signed-off-by:
-
Finn Thain authored
commit 25fcf94a upstream. This reverts commit 4822827a. The purpose of that commit was to suppress a timeout warning message which appeared to be caused by target latency. But suppressing the warning is undesirable as the warning may indicate a messed up transfer count. Another problem with that commit is that 15 ms is too long to keep interrupts disabled as interrupt latency can cause system clock drift and other problems. Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org Fixes: 4822827a ("scsi: ncr5380: Increase register polling limit") Signed-off-by:
-
Finn Thain authored
commit 57f31326 upstream. The reselection interrupt gets disabled during selection and must be re-enabled when hostdata->connected becomes NULL. If it isn't re-enabled a disconnected command may time-out or the target may wedge the bus while trying to reselect the host. This can happen after a command is aborted. Fix this by enabling the reselection interrupt in NCR5380_main() after calls to NCR5380_select() and NCR5380_information_transfer() return. Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org # v4.9+ Fixes: 8b00c3d5 ("ncr5380: Implement new eh_abort_handler") Signed-off-by:
-
Finn Thain authored
commit 6a162836 upstream. Replace a 'goto' statement with a simple 'return' where possible. This improves readability. No functional change. Tested-by:
-
Juergen Gross authored
commit a1078e82 upstream. Instead of trying to allocate pages with GFP_USER in add_ballooned_pages() check the available free memory via si_mem_available(). GFP_USER is far less limiting memory exhaustion than the test via si_mem_available(). This will avoid dom0 running out of memory due to excessive foreign page mappings especially on ARM and on x86 in PVH mode, as those don't have a pre-ballooned area which can be used for foreign mappings. As the normal ballooning suffers from the same problem don't balloon down more than si_mem_available() pages in one iteration. At the same time limit the default maximum number of retries. This is part of XSA-300. Signed-off-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Denis Efremov authored
[ Upstream commit da99466a ] This fixes a global out-of-bounds read access in the copy_buffer function of the floppy driver. The FDDEFPRM ioctl allows one to set the geometry of a disk. The sect and head fields (unsigned int) of the floppy_drive structure are used to compute the max_sector (int) in the make_raw_rw_request function. It is possible to overflow the max_sector. Next, max_sector is passed to the copy_buffer function and used in one of the memcpy calls. An unprivileged user could trigger the bug if the device is accessible, but requires a floppy disk to be inserted. The patch adds the check for the .sect * .head multiplication for not overflowing in the set_geometry function. The bug was found by syzkaller. Signed-off-by:
Denis Efremov <efremov@ispras.ru> Tested-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Denis Efremov authored
[ Upstream commit 9b04609b ] This fixes the invalid pointer dereference in the drive_name function of the floppy driver. The native_format field of the struct floppy_drive_params is used as floppy_type array index in the drive_name function. Thus, the field should be checked the same way as the autodetect field. To trigger the bug, one could use a value out of range and set the drive parameters with the FDSETDRVPRM ioctl. Next, FDGETDRVTYP ioctl should be used to call the drive_name. A floppy disk is not required to be inserted. CAP_SYS_ADMIN is required to call FDSETDRVPRM. The patch adds the check for a value of the native_format field to be in the '0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array indices. The bug was found by syzkaller. Signed-off-by:
-
Denis Efremov authored
[ Upstream commit 5635f897 ] This fixes a global out-of-bounds read access in the next_valid_format function of the floppy driver. The values from autodetect field of the struct floppy_drive_params are used as indices for the floppy_type array in the next_valid_format function 'floppy_type[DP->autodetect[probed_format]].sect'. To trigger the bug, one could use a value out of range and set the drive parameters with the FDSETDRVPRM ioctl. A floppy disk is not required to be inserted. CAP_SYS_ADMIN is required to call FDSETDRVPRM. The patch adds the check for values of the autodetect field to be in the '0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array indices. The bug was found by syzkaller. Signed-off-by:
-
Denis Efremov authored
[ Upstream commit f3554aeb ] This fixes a divide by zero error in the setup_format_params function of the floppy driver. Two consecutive ioctls can trigger the bug: The first one should set the drive geometry with such .sect and .rate values for the F_SECT_PER_TRACK to become zero. Next, the floppy format operation should be called. A floppy disk is not required to be inserted. An unprivileged user could trigger the bug if the device is accessible. The patch checks F_SECT_PER_TRACK for a non-zero value in the set_geometry function. The proper check should involve a reasonable upper limit for the .sect and .rate fields, but it could change the UAPI. The patch also checks F_SECT_PER_TRACK in the setup_format_params, and cancels the formatting operation in case of zero. The bug was found by syzkaller. Signed-off-by:
-
Colin Ian King authored
[ Upstream commit 9fe06a51 ] A recent commit efa14c39 ("iavf: allow null RX descriptors") added a null pointer sanity check on rx_buffer, however, rx_buffer is being dereferenced before that check, which implies a null pointer dereference bug can potentially occur. Fix this by only dereferencing rx_buffer until after the null pointer check. Addresses-Coverity: ("Dereference before null check") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Josua Mayer authored
[ Upstream commit 433a06d7 ] Defer probing of the orion-mdio interface when getting a clock returns EPROBE_DEFER. This avoids locking up the Armada 8k SoC when mdio is used before all clocks have been enabled. Signed-off-by:
Josua Mayer <josua@solid-run.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Taehee Yoo authored
[ Upstream commit a2bed907 ] Current gtp_newlink() could be called after unregister_pernet_subsys(). gtp_newlink() uses gtp_net but it can be destroyed by unregister_pernet_subsys(). So unregister_pernet_subsys() should be called after rtnl_link_unregister(). Test commands: #SHELL 1 while : do for i in {1..5} do ./gtp-link add gtp$i & done killall gtp-link done #SHELL 2 while : do modprobe -rv gtp done Splat looks like: [ 753.176631] BUG: KASAN: use-after-free in gtp_newlink+0x9b4/0xa5c [gtp] [ 753.177722] Read of size 8 at addr ffff8880d48f2458 by task gtp-link/7126 [ 753.179082] CPU: 0 PID: 7126 Comm: gtp-link Tainted: G W 5.2.0-rc6+ #50 [ 753.185801] Call Trace: [ 753.186264] dump_stack+0x7c/0xbb [ 753.186863] ? gtp_newlink+0x9b4/0xa5c [gtp] [ 753.187583] print_address_description+0xc7/0x240 [ 753.188382] ? gtp_newlink+0x9b4/0xa5c [gtp] [ 753.189097] ? gtp_newlink+0x9b4/0xa5c [gtp] [ 753.189846] __kasan_report+0x12a/0x16f [ 753.190542] ? gtp_newlink+0x9b4/0xa5c [gtp] [ 753.191298] kasan_report+0xe/0x20 [ 753.191893] gtp_newlink+0x9b4/0xa5c [gtp] [ 753.192580] ? __netlink_ns_capable+0xc3/0xf0 [ 753.193370] __rtnl_newlink+0xb9f/0x11b0 [ ... ] [ 753.241201] Allocated by task 7186: [ 753.241844] save_stack+0x19/0x80 [ 753.242399] __kasan_kmalloc.constprop.3+0xa0/0xd0 [ 753.243192] __kmalloc+0x13e/0x300 [ 753.243764] ops_init+0xd6/0x350 [ 753.244314] register_pernet_operations+0x249/0x6f0 [ ... ] [ 753.251770] Freed by task 7178: [ 753.252288] save_stack+0x19/0x80 [ 753.252833] __kasan_slab_free+0x111/0x150 [ 753.253962] kfree+0xc7/0x280 [ 753.254509] ops_free_list.part.11+0x1c4/0x2d0 [ 753.255241] unregister_pernet_operations+0x262/0x390 [ ... ] [ 753.285883] list_add corruption. next->prev should be prev (ffff8880d48f2458), but was ffff8880d497d878. (next. [ 753.287241] ------------[ cut here ]------------ [ 753.287794] kernel BUG at lib/list_debug.c:25! [ 753.288364] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI [ 753.289099] CPU: 0 PID: 7126 Comm: gtp-link Tainted: G B W 5.2.0-rc6+ #50 [ 753.291036] RIP: 0010:__list_add_valid+0x74/0xd0 [ 753.291589] Code: 48 39 da 75 27 48 39 f5 74 36 48 39 dd 74 31 48 83 c4 08 b8 01 00 00 00 5b 5d c3 48 89 d9 48b [ 753.293779] RSP: 0018:ffff8880cae8f398 EFLAGS: 00010286 [ 753.294401] RAX: 0000000000000075 RBX: ffff8880d497d878 RCX: 0000000000000000 [ 753.296260] RDX: 0000000000000075 RSI: 0000000000000008 RDI: ffffed10195d1e69 [ 753.297070] RBP: ffff8880cd250ae0 R08: ffffed101b4bff21 R09: ffffed101b4bff21 [ 753.297899] R10: 0000000000000001 R11: ffffed101b4bff20 R12: ffff8880d497d878 [ 753.298703] R13: 0000000000000000 R14: ffff8880cd250ae0 R15: ffff8880d48f2458 [ 753.299564] FS: 00007f5f79805740(0000) GS:ffff8880da400000(0000) knlGS:0000000000000000 [ 753.300533] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 753.301231] CR2: 00007fe8c7ef4f10 CR3: 00000000b71a6006 CR4: 00000000000606f0 [ 753.302183] Call Trace: [ 753.302530] gtp_newlink+0x5f6/0xa5c [gtp] [ 753.303037] ? __netlink_ns_capable+0xc3/0xf0 [ 753.303576] __rtnl_newlink+0xb9f/0x11b0 [ 753.304092] ? rtnl_link_unregister+0x230/0x230 Fixes: 459aa660 ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
Taehee Yoo authored
[ Upstream commit 1788b856 ] gtp_encap_destroy() is called twice. 1. When interface is deleted. 2. When udp socket is destroyed. either gtp->sk0 or gtp->sk1u could be freed by sock_put() in gtp_encap_destroy(). so, when gtp_encap_destroy() is called again, it would uses freed sk pointer. patch makes gtp_encap_destroy() to set either gtp->sk0 or gtp->sk1u to null. in addition, both gtp->sk0 and gtp->sk1u pointer are protected by rtnl_lock. so, rtnl_lock() is added. Test command: gtp-link add gtp1 & killall gtp-link ip link del gtp1 Splat looks like: [ 83.182767] BUG: KASAN: use-after-free in __lock_acquire+0x3a20/0x46a0 [ 83.184128] Read of size 8 at addr ffff8880cc7d5360 by task ip/1008 [ 83.185567] CPU: 1 PID: 1008 Comm: ip Not tainted 5.2.0-rc6+ #50 [ 83.188469] Call Trace: [ ... ] [ 83.200126] lock_acquire+0x141/0x380 [ 83.200575] ? lock_sock_nested+0x3a/0xf0 [ 83.201069] _raw_spin_lock_bh+0x38/0x70 [ 83.201551] ? lock_sock_nested+0x3a/0xf0 [ 83.202044] lock_sock_nested+0x3a/0xf0 [ 83.202520] gtp_encap_destroy+0x18/0xe0 [gtp] [ 83.203065] gtp_encap_disable.isra.14+0x13/0x50 [gtp] [ 83.203687] gtp_dellink+0x56/0x170 [gtp] [ 83.204190] rtnl_delete_link+0xb4/0x100 [ ... ] [ 83.236513] Allocated by task 976: [ 83.236925] save_stack+0x19/0x80 [ 83.237332] __kasan_kmalloc.constprop.3+0xa0/0xd0 [ 83.237894] kmem_cache_alloc+0xd8/0x280 [ 83.238360] sk_prot_alloc.isra.42+0x50/0x200 [ 83.238874] sk_alloc+0x32/0x940 [ 83.239264] inet_create+0x283/0xc20 [ 83.239684] __sock_create+0x2dd/0x540 [ 83.240136] __sys_socket+0xca/0x1a0 [ 83.240550] __x64_sys_socket+0x6f/0xb0 [ 83.240998] do_syscall_64+0x9c/0x450 [ 83.241466] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 83.242061] [ 83.242249] Freed by task 0: [ 83.242616] save_stack+0x19/0x80 [ 83.243013] __kasan_slab_free+0x111/0x150 [ 83.243498] kmem_cache_free+0x89/0x250 [ 83.244444] __sk_destruct+0x38f/0x5a0 [ 83.245366] rcu_core+0x7e9/0x1c20 [ 83.245766] __do_softirq+0x213/0x8fa Fixes: 1e3a3abd ("gtp: make GTP sockets in gtp_newlink optional") Signed-off-by:
-
Taehee Yoo authored
[ Upstream commit 3f167e19 ] ipv4_pdp_add() is called in RCU read-side critical section. So GFP_KERNEL should not be used in the function. This patch make ipv4_pdp_add() to use GFP_ATOMIC instead of GFP_KERNEL. Test commands: gtp-link add gtp1 & gtp-tunnel add gtp1 v1 100 200 1.1.1.1 2.2.2.2 Splat looks like: [ 130.618881] ============================= [ 130.626382] WARNING: suspicious RCU usage [ 130.626994] 5.2.0-rc6+ #50 Not tainted [ 130.627622] ----------------------------- [ 130.628223] ./include/linux/rcupdate.h:266 Illegal context switch in RCU read-side critical section! [ 130.629684] [ 130.629684] other info that might help us debug this: [ 130.629684] [ 130.631022] [ 130.631022] rcu_scheduler_active = 2, debug_locks = 1 [ 130.632136] 4 locks held by gtp-tunnel/1025: [ 130.632925] #0: 000000002b93c8b7 (cb_lock){++++}, at: genl_rcv+0x15/0x40 [ 130.634159] #1: 00000000f17bc999 (genl_mutex){+.+.}, at: genl_rcv_msg+0xfb/0x130 [ 130.635487] #2: 00000000c644ed8e (rtnl_mutex){+.+.}, at: gtp_genl_new_pdp+0x18c/0x1150 [gtp] [ 130.636936] #3: 0000000007a1cde7 (rcu_read_lock){....}, at: gtp_genl_new_pdp+0x187/0x1150 [gtp] [ 130.638348] [ 130.638348] stack backtrace: [ 130.639062] CPU: 1 PID: 1025 Comm: gtp-tunnel Not tainted 5.2.0-rc6+ #50 [ 130.641318] Call Trace: [ 130.641707] dump_stack+0x7c/0xbb [ 130.642252] ___might_sleep+0x2c0/0x3b0 [ 130.642862] kmem_cache_alloc_trace+0x1cd/0x2b0 [ 130.643591] gtp_genl_new_pdp+0x6c5/0x1150 [gtp] [ 130.644371] genl_family_rcv_msg+0x63a/0x1030 [ 130.645074] ? mutex_lock_io_nested+0x1090/0x1090 [ 130.645845] ? genl_unregister_family+0x630/0x630 [ 130.646592] ? debug_show_all_locks+0x2d0/0x2d0 [ 130.647293] ? check_flags.part.40+0x440/0x440 [ 130.648099] genl_rcv_msg+0xa3/0x130 [ ... ] Fixes: 459aa660 ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by:
-
Taehee Yoo authored
[ Upstream commit e198987e ] gtp_encap_enable_socket() and gtp_encap_destroy() are not protected by rcu_read_lock(). and it's not safe to write sk->sk_user_data. This patch make these functions to use lock_sock() instead of rcu_dereference_sk_user_data(). Test commands: gtp-link add gtp1 Splat looks like: [ 83.238315] ============================= [ 83.239127] WARNING: suspicious RCU usage [ 83.239702] 5.2.0-rc6+ #49 Not tainted [ 83.240268] ----------------------------- [ 83.241205] drivers/net/gtp.c:799 suspicious rcu_dereference_check() usage! [ 83.243828] [ 83.243828] other info that might help us debug this: [ 83.243828] [ 83.246325] [ 83.246325] rcu_scheduler_active = 2, debug_locks = 1 [ 83.247314] 1 lock held by gtp-link/1008: [ 83.248523] #0: 0000000017772c7f (rtnl_mutex){+.+.}, at: __rtnl_newlink+0x5f5/0x11b0 [ 83.251503] [ 83.251503] stack backtrace: [ 83.252173] CPU: 0 PID: 1008 Comm: gtp-link Not tainted 5.2.0-rc6+ #49 [ 83.253271] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 83.254562] Call Trace: [ 83.254995] dump_stack+0x7c/0xbb [ 83.255567] gtp_encap_enable_socket+0x2df/0x360 [gtp] [ 83.256415] ? gtp_find_dev+0x1a0/0x1a0 [gtp] [ 83.257161] ? memset+0x1f/0x40 [ 83.257843] gtp_newlink+0x90/0xa21 [gtp] [ 83.258497] ? __netlink_ns_capable+0xc3/0xf0 [ 83.259260] __rtnl_newlink+0xb9f/0x11b0 [ 83.260022] ? rtnl_link_unregister+0x230/0x230 [ ... ] Fixes: 1e3a3abd ("gtp: make GTP sockets in gtp_newlink optional") Signed-off-by:
-
