tsc->polling is write only and the poll local is meaningless
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

With device core now able to setup the default pin configuration,
the pin configuration code based on the deprecated Samsung specific
gpio bindings is removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Added MAP_TRIGGERS_TO_BUTTONS for Mad Catz Street Fighter IV FightPad
device. This controller model was already supported by the xpad
driver, but none of the buttons work correctly without this change.

Tested on kernel version 3.9.5.
Signed-off-by: Shawn Joseph <jms.576@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Several drivers don't build on s390 with CONFIG_PCI disabled as
they require MMIO functions.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org # 3.9
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The command and status register in the driver were swapped with
respect to the order specified in the datasheet (CY8CTMA140).
Confirmed with Cypress that the order in the datasheet is correct.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

For the devices that has blocking with timeout communication, these
extra handshakes will prevent one timeout delay in startup sequence

Tested-by: Ferruh Yigit <fery@cypress.com> on TMA300-DVK
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

memcpy param is wrong because of offset in bl_cmd, this may corrupt the
stack which may cause a crash.

Tested-by: Ferruh Yigit <fery@cypress.com> on TMA300-DVK
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

And make the lines easier to read.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In summary, the symptom is intermittent key events lost after resume
on some machines with synaptics touchpad (seems this is synaptics _only_),
and key events loss is due to serio port reconnect after psmouse sync lost.
Removing psmouse and inserting it back during the suspend/resume process
is able to work around the issue, so the difference between psmouse_connect()
and psmouse_reconnect() is the key to the root cause of this problem.

After comparing the two different paths, synaptics driver has its own
implementation of synaptics_reconnect(), and the missing psmouse_probe()
seems significant, the patch below added psmouse_probe() to the reconnect
process, and has been verified many times that the issue could not be reliably
reproduced.

There are two PS/2 commands in psmouse_probe():

  1. PSMOUSE_CMD_GETID
  2. PSMOUSE_CMD_RESET_DIS

Only the PSMOUSE_CMD_GETID seems to be significant. The
PSMOUSE_CMD_RESET_DIS is irrelevant to this issue after trying
several times.  So we have only implemented this patch to issue
the PSMOUSE_CMD_GETID so far.
Tested-by: Daniel Manrique <daniel.manrique@canonical.com>
Signed-off-by: James M Leddy <james.leddy@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

plus send begin and end of express keys events for
Cintiq 13HD and DTH2242/DTK2241
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add new styli for Cintiq 13HD and 22HD. Update comments for
for tools. Check whole 10 nibbles of tool ID for tool
types. Remove unuecessary tool type for Intuos series PAD.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Cintiq 13HD, DTK 2241, and Cintiq 22HDT are supported.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The egalax_ts touchscreen modul not report ABS_MT_POSITION_Y proper.
As result it may be, that upper software levels only receive x coordinates well.
Signed-off-by: Heiko Abraham <abrahamh@web.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare first set of updates for 3.10 merge window.

The trackpoint driver sets various parameter default values, all of
which happen to be power-on defaults (Source: IBM TrackPoint Engineering
Specification, Version 4.0. Also confirmed by empirical data).

By sending the power-on reset command to reset all parameters to
power-on state, we can skip the lengthy process of programming all
parameters. In testing, ~2.5 secs of time writing parameters was reduced
to .35 seconds waiting for power-on reset to complete.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Same as Cintiq 24HDT, DTH2242 has two interfaces sharing one configuration.
This patch ignores the second interface.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This form is more concise.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We no longer need to set up the reset pin for the st1232 in the board
code, but can pass the GPIO number via the platform data to the driver.
This results in a cleaner grouping of the device setup.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We add the possibility to hand over a GPIO number for the reset pin.
This way we can remove existing board code that takes care of it and
group this information properly in the platform data or in the device
tree configuration.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use the devm_* managed functions to allocate resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Reported-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The MFT device in the Cintiq 24HDT has two interfaces sharing the
same configuration. Without this patch, the driver attempts to
make use of both interfaces, even though the second interface is
not compatible with this driver.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Most semi-mt drivers use the slots in a manual way, but really only
need to treat the finger count manually. With this patch, a semi-mt
driver may use the input-mt core for everything else.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some devices have too few buttons, which it makes it hard to have
a reset combo that won't trigger automatically.  As such a
timeout functionality that requires the combination to be held for
a given amount of time before triggering is introduced.

If a key combo is recognized and held for a 'timeout' amount of time,
the system triggers a reset.  If the timeout value is omitted the
driver simply ignores the functionality.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

NVIDIA's Tegra20 and Tegra30 supports the 16x8 keyboard matrix and T114
support the 11x8 Key matrix.

Add support for defining the maximum row/columns based on SoC through
proper compatibility.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Using devm_ functions can make the code cleaner and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add match table for device tree binding and dts binding doc.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Event value is wrong. Should be in range -2048 to 2047, but is in
range 0 to 4095.  Use s8 to int conversion and remove 0xfff mask.
Signed-off-by: Sebastien Royen <sebastien.royen@armadeus.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

'pdata' is already dereferenced earlier. Hence this check is
meaningless.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

kfree on a null pointer is a no-op. Hence null check is not
necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.

drivers/input/misc/ad714x-i2c.c:17:12: warning: 'ad714x_i2c_suspend' defined but not used [-Wunused-function]
drivers/input/misc/ad714x-i2c.c:22:12: warning: 'ad714x_i2c_resume' defined but not used [-Wunused-function]
drivers/input/misc/ad714x-spi.c:20:12: warning: 'ad714x_spi_suspend' defined but not used [-Wunused-function]
drivers/input/misc/ad714x-spi.c:25:12: warning: 'ad714x_spi_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.

drivers/input/misc/adxl34x-spi.c:98:12: warning: 'adxl34x_spi_suspend' defined but not used [-Wunused-function]
drivers/input/misc/adxl34x-spi.c:108:12: warning: 'adxl34x_spi_resume' defined but not used [-Wunused-function]
drivers/input/misc/adxl34x-i2c.c:109:12: warning: 'adxl34x_i2c_suspend' defined but not used [-Wunused-function]
drivers/input/misc/adxl34x-i2c.c:119:12: warning: 'adxl34x_i2c_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch converts the drivers to use the
module_platform_driver_probe() macro which makes the code smaller and
a bit simpler.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>