- 07 Nov, 2012 10 commits
-
-
Ming Lei authored
This patch introduces the below two helpers to prepare for solving the usbnet runtime PM problem, which may cause some network utilities (ifconfig, ethtool,...) touch a suspended device. usbnet_read_cmd_nopm() usbnet_write_cmd_nopm() The above two helpers should be called by usbnet resume/suspend callback to avoid deadlock. Signed-off-by:
Ming Lei <ming.lei@canonical.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Rob Herring authored
On gcc 4.7, we will get alignment traps in the ip stack if we don't align the ip headers on receive. The h/w can support this, so use ip aligned allocations. Cut down the unnecessary padding on the allocation. The buffer can start on any byte alignment, but the size including the begining offset must be 8 byte aligned. So the h/w buffer size must include the NET_IP_ALIGN offset. Thanks to Eric Dumazet for the initial patch highlighting the padding issues. Signed-off-by:
Rob Herring <rob.herring@calxeda.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Rob Herring authored
Only generate tx interrupts on every ring size / 4 descriptors. Move the netif_stop_queue call to the end of the xmit function rather than checking at the beginning. Signed-off-by:
-
Rob Herring authored
The interrupts have already been cleared, so we don't need to clear them again. Also, we could miss interrupts if they are cleared, but we don't process the packet. Signed-off-by:
-
Rob Herring authored
The standard readl/writel accessors involve a spinlock and cache sync operation on ARM platforms with an outer cache. Only DMA triggering accesses need this, so use the raw variants instead in the critical paths. The relaxed variants would be more appropriate, but don't exist on all arches. Signed-off-by:
-
Rob Herring authored
New received frames will trigger the rx DMA to poll the DMA descriptors, so there is no need to tell the h/w to poll. We also want to enable dropping frames from the fifo when there is no buffer. Signed-off-by:
-
Rob Herring authored
Enable the tx dma to start reading the next frame while sending the current frame. Signed-off-by:
-
Eric Dumazet authored
Commit 56b765b7 (htb: improved accuracy at high rates) introduced two bugs : 1) one bstats_update() was inadvertently removed from htb_dequeue_tree(), breaking statistics/rate estimation. 2) Missing qdisc_put_rtab() calls in htb_change_class(), leaking kernel memory, now struct htb_class no longer retains pointers to qdisc_rate_table structs. Since only rate is used, dont use qdisc_get_rtab() calls copying data we ignore anyway. Signed-off-by:
-
Nithin Nayak Sujir authored
instead of making separate tg3_napi_disable() and netif_tx_disable() calls. Update version to 3.126. Signed-off-by:
Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Michael Chan authored
Add support for 5717C0 which is a 5720A0 with special bonds-out option. Signed-off-by:
-
- 06 Nov, 2012 5 commits
-
-
Jean-Christophe PLAGNIOL-VILLARD authored
If no pinctrl available just report a warning as some architecture may not need to do anything. Signed-off-by:
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Tested-by:
Joachim Eastwood <manabian@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: netdev@vger.kernel.org Signed-off-by:
-
Jean-Christophe PLAGNIOL-VILLARD authored
Signed-off-by:
-
Kumar Amit Mehta authored
Fixed some coding style issues. Signed-off-by:
Kumar Amit Mehta <gmate.amit@gmail.com> Acked-by:
Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by:
-
Kumar Amit Mehta authored
checkpatch.pl throws error message for the current code. This patch fixes this coding style issue. Signed-off-by:
Jitendra Kalsaria <Jitendra.kalsaria@qlogic.com> Signed-off-by:
-
Daniel Borkmann authored
This patch is a follow-up for patch "net: filter: add vlan tag access" to support the new VLAN_TAG/VLAN_TAG_PRESENT accessors in BPF JIT. Signed-off-by:
Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch> Signed-off-by:
-
- 04 Nov, 2012 2 commits
-
-
hayeswang authored
The following chips need to enable internal settings to let ASPM and clock request work. RTL8111E-VL, RTL8111F, RTL8411, RTL8111G RTL8105, RTL8402, RTL8106 Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
Lee Jones authored
Instead of issuing (0) statements when !CONFIG_SYSFS which will cause 'warning: ', we'll use inline statements instead. This will effectively do the same thing, but suppress any unnecessary warnings. Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: bridge@lists.linux-foundation.org Cc: netdev@vger.kernel.org Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
- 03 Nov, 2012 23 commits
-
-
Julia Lawall authored
Use WARN rather than printk followed by WARN_ON(1), for conciseness. A simplified version of the semantic patch that makes this transformation is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression list es; @@ -printk( +WARN(1, es); -WARN_ON(1); // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Paul Bolle authored
Building atp.o triggers this GCC warning: drivers/net/ethernet/realtek/atp.c: In function ‘set_rx_mode’: drivers/net/ethernet/realtek/atp.c:871:26: warning: ‘mc_filter[0]’ may be used uninitialized in this function [-Wuninitialized] GCC is correct. In promiscuous mode 'mc_filter' will be used uninitialized in set_rx_mode_8012(), which is apparently inlined into set_rx_mode(). But it turns out set_rx_mode_8012() will never be called, since net_local.chip_type will always be RTL8002. So we can just remove set_rx_mode_8012() and do some related cleanups. Signed-off-by:Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
Richard Cochran authored
The CPSW driver remaps two different IO regions, but fails to unmap them both. This patch fixes the issue by calling iounmap in the appropriate places. Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Richard Cochran authored
The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch changes the names to conform to the published Technical Reference Manual from TI, in order to make working on the code less confusing. Signed-off-by:
-
John Fastabend authored
The bridge notify hook rtnl_bridge_notify() was not handling the case where the master flags was set or with both flags set. First flags are not being passed correctly and second the logic to parse them is broken. This patch passes the original flags value and fixes the logic. Reported-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
John Fastabend <john.r.fastabend@intel.com> Signed-off-by:
-
Vitalii Demianets authored
When underlying phy driver restores its state very fast after being brought down and up so that macb driver function macb_handle_link_change() was never called with link state "down", driver's internal representation of phy speed and duplex (bp->speed and bp->duplex) didn't change. So, macb driver sees no reason to perform actual write to the NCFGR register, although the speed and duplex settings in that register were reset when interface was brought down and up. In that case actual phy speed and duplex differ from NCFGR settings. The patch fixes that by keeping internal driver representation of speed and duplex in sync with actual content of NCFGR. Signed-off-by:
Vitalii Demianets <vitas@nppfactor.kiev.ua> Signed-off-by:
-
YOSHIFUJI Hideaki / 吉藤英明 authored
Signed-off-by:
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by:
-
YOSHIFUJI Hideaki / 吉藤英明 authored
Signed-off-by:
-
Richard Cochran authored
Ben Hutchings recently came up with a better way to handle the kconfig dependencies for the PTP hardware clocks. This patch converts one new and one older driver to the new scheme. Signed-off-by:
-
Vimalkumar authored
Current HTB (and TBF) uses rate table computed by the "tc" userspace program, which has the following issue: The rate table has 256 entries to map packet lengths to token (time units). With TSO sized packets, the 256 entry granularity leads to loss/gain of rate, making the token bucket inaccurate. Thus, instead of relying on rate table, this patch explicitly computes the time and accounts for packet transmission times with nanosecond granularity. This greatly improves accuracy of HTB with a wide range of packet sizes. Example: tc qdisc add dev $dev root handle 1: \ htb default 1 tc class add dev $dev classid 1:1 parent 1: \ rate 5Gbit mtu 64k Here is an example of inaccuracy: $ iperf -c host -t 10 -i 1 With old htb: eth4: 34.76 Mb/s In 5827.98 Mb/s Out - 65836.0 p/s In 481273.0 p/s Out [SUM] 9.0-10.0 sec 669 MBytes 5.61 Gbits/sec [SUM] 0.0-10.0 sec 6.50 GBytes 5.58 Gbits/sec With new htb: eth4: 28.36 Mb/s In 5208.06 Mb/s Out - 53704.0 p/s In 430076.0 p/s Out [SUM] 9.0-10.0 sec 594 MBytes 4.98 Gbits/sec [SUM] 0.0-10.0 sec 5.80 GBytes 4.98 Gbits/sec The bits per second on the wire is still 5200Mb/s with new HTB because qdisc accounts for packet length using skb->len, which is smaller than total bytes on the wire if GSO is used. But that is for another patch regardless of how time is accounted. Many thanks to Eric Dumazet for review and feedback. Signed-off-by:Vimalkumar <j.vimal@gmail.com> Signed-off-by:
-
Vincent Bernat authored
"ip link add ... type vxlan ... ttl X" allows a user to set the TTL used by a VXLAN for encapsulation. The provided value was ignored by vxlan module and the default value of 1 was used when encapsulating multicast packets. Signed-off-by:
Vincent Bernat <bernat@luffy.cx> Acked-by:
Stephen Hemminger <shemminger@vyatta.com> Signed-off-by:
-
Steve Glendinning authored
This patch adds support for wol wakeup on unicast, broadcast, multicast and arp frames. Signed-off-by:
Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by:
-
Antonio Quartulli authored
Add Ethertype 0x4305 (not an officially registered id). This Ethertype is used by every frame generated by B.A.T.M.A.N.-Advanced. Its definition is currently batman-adv local only and since it is not officially registered it is better to make its definition kernel-wide so that we avoid collisions given by future unofficial uses of the same Ethertype. Signed-off-by:
Antonio Quartulli <ordex@autistici.org> Signed-off-by:
-
Kirill Smelkov authored
After d58d46b5 (r8169: jumbo fixes.) max frame len is stored in rtl_chip_infos[].jumbo_max for each chip and SafeMtu should be gone. Signed-off-by:
Kirill Smelkov <kirr@mns.spb.ru> Signed-off-by:
-
Amerigo Wang authored
As suggested by Eric, we could introduce a helper function for ipv6 too, to avoid checking if rt is NULL before dst_release(). Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
Cong Wang <amwang@redhat.com> Signed-off-by:
-
Eric Dumazet authored
We can save a test in ip_rt_put(), considering dst_release() accepts a NULL parameter, and dst is first element in rtable. Add a BUILD_BUG_ON() to catch any change that could break this assertion. Signed-off-by:
-
Neil Horman authored
Lots of points in the sctp_cmd_interpreter function treat the sctp_cmd_t arg as a void pointer, even though they are written as various other types. Theres no need for this as doing so just leads to possible type-punning issues that could cause crashes, and if we remain type-consistent we can actually just remove the void * member of the union entirely. Change Notes: v2) * Dropped chunk that modified SCTP_NULL to create a marker pattern should anyone try to use a SCTP_NULL() assigned sctp_arg_t, Assigning to .zero provides the same effect and should be faster, per Vlad Y. v3) * Reverted part of V2, opting to use memset instead of .zero, so that the entire union is initalized thus avoiding the i164 speculative load problems previously encountered, per Dave M.. Also rewrote SCTP_[NO]FORCE so as to use common infrastructure a little more Signed-off-by: Neil Horman <nhorman@tuxdriver.com CC: Vlad Yasevich <vyasevich@gmail.com> CC: "David S. Miller" <davem@davemloft.net> CC: linux-sctp@vger.kernel.org Signed-off-by: -
Amerigo Wang authored
In dev_forward_change(), it is useless to check if idev->dev is NULL, it is always non-NULL here. Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
-
Daniel Borkmann authored
Some years ago, the ktime_t helper functions ktime_now() and ktime_lt() have been introduced. Instead of defining them inside pktgen.c, they should either use ktime_t library functions or, if not available, they should be defined in ktime.h, so that also others can benefit from them. ktime_compare() is introduced with a similar notion as in timespec_compare(). Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Eric Dumazet authored
For passive TCP connections using TCP_DEFER_ACCEPT facility, we incorrectly increment req->retrans each time timeout triggers while no SYNACK is sent. SYNACK are not sent for TCP_DEFER_ACCEPT that were established (for which we received the ACK from client). Only the last SYNACK is sent so that we can receive again an ACK from client, to move the req into accept queue. We plan to change this later to avoid the useless retransmit (and potential problem as this SYNACK could be lost) TCP_INFO later gives wrong information to user, claiming imaginary retransmits. Decouple req->retrans field into two independent fields : num_retrans : number of retransmit num_timeout : number of timeouts num_timeout is the counter that is incremented at each timeout, regardless of actual SYNACK being sent or not, and used to compute the exponential timeout. Introduce inet_rtx_syn_ack() helper to increment num_retrans only if ->rtx_syn_ack() succeeded. Use inet_rtx_syn_ack() from tcp_check_req() to increment num_retrans when we re-send a SYNACK in answer to a (retransmitted) SYN. Prior to this patch, we were not counting these retransmits. Change tcp_v[46]_rtx_synack() to increment TCP_MIB_RETRANSSEGS only if a synack packet was successfully queued. Reported-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
-
Ben Hutchings authored
Commit e5a55a89 ('net: create generic bridge ops') broke the handling of a non-zero starting index in rtnl_bridge_getlink() (based on the old br_dump_ifinfo()). When the starting index is non-zero, we need to increment the current index for each entry that we are skipping. Also, we need to check the index before both cases, since we may previously have stopped iteration between getting information about a device from its master and from itself. Signed-off-by:
-
Nicolas Dichtel authored
fib6_add_rt2node() will reject the nexthop if this flag is set, so we perform the check only for the first nexthop. Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Ben Hutchings authored
Since this array is no longer part of the bridge driver, it should have an 'eth' prefix not 'br'. We also assume that either it's 16-bit-aligned or the architecture has efficient unaligned access. Ensure the first of these is true by explicitly aligning it. Signed-off-by:
-
