The resource group limits for IPA v3.1 mistakenly used 6 bit wide mask
values, when the hardware actually uses 8. Out of range values were
silently ignored before, so the IPA worked as expected. However the
new generalised register definitions introduce stricter checking here,
they now cause some splats and result in the value 0 being written
instead. Fix the limit bitmask widths so that the correct values can be
written.

Fixes: 1c418c4a ("net: ipa: define resource group/type IPA register fields")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Tested-by: Jami Kettunen <jami.kettunen@somainline.org>
Link: https://lore.kernel.org/r/20221024210336.4014983-2-caleb.connolly@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Some resource limits on IPA v3.5.1 have their max values set to
255, this causes a few splats in ipa_reg_encode and prevents the
IPA from booting properly. The limits are all 6 bits wide so
adjust the max values to 63.

Fixes: 1c418c4a ("net: ipa: define resource group/type IPA register fields")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20221024210336.4014983-1-caleb.connolly@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
while unbinding device.

Fixes: 8ca86fd8 ("net: Micrel KSZ8841/2 PCI Ethernet driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221024131338.2848959-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix setting bits for specific flow_type for GLQF_HASH_INSET register.
In previous version all of the bits were set only in hena register, while
in inset only one bit was set. In order for this working correctly on all
types of cards these bits needs to be set correctly for both hena and inset
registers.

Fixes: eb0dd6e4 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-3-jacob.e.keller@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When a reset was triggered on one VF with i40e_reset_vf
global PF state __I40E_VF_DISABLE was set on a PF until
the reset finished. If immediately after triggering reset
on one VF there is a request to reset on another
it will cause a hang on VF side because VF will be notified
of incoming reset but the reset will never happen because
of this global state, we will get such error message:

[  +4.890195] iavf 0000:86:02.1: Never saw reset

and VF will hang waiting for the reset to be triggered.

Fix this by introducing new VF state I40E_VF_STATE_RESETTING
that will be set on a VF if it is currently resetting instead of
the global __I40E_VF_DISABLE PF state.

Fixes: 3ba9bcb4 ("i40e: add locking around VF reset")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-2-jacob.e.keller@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When enabling flow type for RSS hash via ethtool:

ethtool -N $pf rx-flow-hash tcp4|tcp6|udp4|udp6 s|d

the driver would fail to setup this setting on X722
device since it was using the mask on the register
dedicated for X710 devices.

Apply a different mask on the register when setting the
RSS hash for the X722 device.

When displaying the flow types enabled via ethtool:

ethtool -n $pf rx-flow-hash tcp4|tcp6|udp4|udp6

the driver would print wrong values for X722 device.

Fix this issue by testing masks for X722 device in
i40e_get_rss_hash_opts function.

Fixes: eb0dd6e4 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-1-jacob.e.keller@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Another syzbot report [1] with no reproducer hints
at a bug in ip6_gre tunnel (dev:ip6gretap0)

Since ipv6 mcast code makes sure to read dev->mtu once
and applies a sanity check on it (see commit b9b312a7
"ipv6: mcast: better catch silly mtu values"), a remaining
possibility is that a layer is able to set dev->mtu to
an underflowed value (high order bit set).

This could happen indeed in ip6gre_tnl_link_config_route(),
ip6_tnl_link_config() and ipip6_tunnel_bind_dev()

Make sure to sanitize mtu value in a local variable before
it is written once on dev->mtu, as lockless readers could
catch wrong temporary value.

[1]
skbuff: skb_over_panic: text:ffff80000b7a2f38 len:40 put:40 head:ffff000149dcf200 data:ffff000149dcf2b0 tail:0xd8 end:0xc0 dev:ip6gretap0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:120
Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
Modules linked in:
CPU: 1 PID: 10241 Comm: kworker/1:1 Not tainted 6.0.0-rc7-syzkaller-18095-gbbed346d5a96 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/30/2022
Workqueue: mld mld_ifc_work
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : skb_panic+0x4c/0x50 net/core/skbuff.c:116
lr : skb_panic+0x4c/0x50 net/core/skbuff.c:116
sp : ffff800020dd3b60
x29: ffff800020dd3b70 x28: 0000000000000000 x27: ffff00010df2a800
x26: 00000000000000c0 x25: 00000000000000b0 x24: ffff000149dcf200
x23: 00000000000000c0 x22: 00000000000000d8 x21: ffff80000b7a2f38
x20: ffff00014c2f7800 x19: 0000000000000028 x18: 00000000000001a9
x17: 0000000000000000 x16: ffff80000db49158 x15: ffff000113bf1a80
x14: 0000000000000000 x13: 00000000ffffffff x12: ffff000113bf1a80
x11: ff808000081c0d5c x10: 0000000000000000 x9 : 73f125dc5c63ba00
x8 : 73f125dc5c63ba00 x7 : ffff800008161d1c x6 : 0000000000000000
x5 : 0000000000000080 x4 : 0000000000000001 x3 : 0000000000000000
x2 : ffff0001fefddcd0 x1 : 0000000100000000 x0 : 0000000000000089
Call trace:
skb_panic+0x4c/0x50 net/core/skbuff.c:116
skb_over_panic net/core/skbuff.c:125 [inline]
skb_put+0xd4/0xdc net/core/skbuff.c:2049
ip6_mc_hdr net/ipv6/mcast.c:1714 [inline]
mld_newpack+0x14c/0x270 net/ipv6/mcast.c:1765
add_grhead net/ipv6/mcast.c:1851 [inline]
add_grec+0xa20/0xae0 net/ipv6/mcast.c:1989
mld_send_cr+0x438/0x5a8 net/ipv6/mcast.c:2115
mld_ifc_work+0x38/0x290 net/ipv6/mcast.c:2653
process_one_work+0x2d8/0x504 kernel/workqueue.c:2289
worker_thread+0x340/0x610 kernel/workqueue.c:2436
kthread+0x12c/0x158 kernel/kthread.c:376
ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:860
Code: 91011400 aa0803e1 a90027ea 94373093 (d4210000)

Fixes: c12b395a ("gre: Support GRE over IPv6")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20221024020124.3756833-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

RK3588(s) can have multiple gmac controllers.
Re-use rk3568 logic to distinguish them.

Fixes: 2f2b60a0 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20221021172422.88534-1-sebastian.reichel@collabora.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Merge tag 'ieee802154-for-net-2022-10-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan

Stefan Schmidt says:

====================
pull-request: ieee802154 for net 2022-10-24

Two fixup patches for return code changes of an earlier commit.
Wei Yongjun fixed a missed -EINVAL return on the recent change, while
Alexander Aring adds handling for unknown address type cases as well.

Miquel Raynal fixed a long standing issue with LQI value recording
which got broken 8 years ago. (It got more attention with the work
in progress enhancement in wpan).

* tag 'ieee802154-for-net-2022-10-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
  mac802154: Fix LQI recording
  net: ieee802154: fix error return code in dgram_bind()
  net: ieee802154: return -EINVAL for unknown addr type
====================

Link: https://lore.kernel.org/r/20221024102301.9433-1-stefan@datenfreihafen.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Mat Martineau says:

====================
mptcp: Fixes for 6.1

Patch 1 fixes an issue with assigning subflow IDs in cases where an
incoming MP_JOIN is processed before accept() completes on the MPTCP
socket.

Patches 2 and 3 fix a deadlock issue with fastopen code (new for 6.1) at
connection time.
====================

Link: https://lore.kernel.org/r/20221021225856.88119-1-mathew.j.martineau@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Our CI reported lockdep splat in the fastopen code:
 ======================================================
 WARNING: possible circular locking dependency detected
 6.0.0.mptcp_f5e8bfe9878d+ #1558 Not tainted
 ------------------------------------------------------
 packetdrill/1071 is trying to acquire lock:
 ffff8881bd198140 (sk_lock-AF_INET){+.+.}-{0:0}, at: inet_wait_for_connect+0x19c/0x310

 but task is already holding lock:
 ffff8881b8346540 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0xfdf/0x1740

 which lock already depends on the new lock.

 the existing dependency chain (in reverse order) is:

 -> #1 (k-sk_lock-AF_INET){+.+.}-{0:0}:
        __lock_acquire+0xb6d/0x1860
        lock_acquire+0x1d8/0x620
        lock_sock_nested+0x37/0xd0
        inet_stream_connect+0x3f/0xa0
        mptcp_connect+0x411/0x800
        __inet_stream_connect+0x3ab/0x800
        mptcp_stream_connect+0xac/0x110
        __sys_connect+0x101/0x130
        __x64_sys_connect+0x6e/0xb0
        do_syscall_64+0x59/0x90
        entry_SYSCALL_64_after_hwframe+0x63/0xcd

 -> #0 (sk_lock-AF_INET){+.+.}-{0:0}:
        check_prev_add+0x15e/0x2110
        validate_chain+0xace/0xdf0
        __lock_acquire+0xb6d/0x1860
        lock_acquire+0x1d8/0x620
        lock_sock_nested+0x37/0xd0
        inet_wait_for_connect+0x19c/0x310
        __inet_stream_connect+0x26c/0x800
        tcp_sendmsg_fastopen+0x341/0x650
        mptcp_sendmsg+0x109d/0x1740
        sock_sendmsg+0xe1/0x120
        __sys_sendto+0x1c7/0x2a0
        __x64_sys_sendto+0xdc/0x1b0
        do_syscall_64+0x59/0x90
        entry_SYSCALL_64_after_hwframe+0x63/0xcd

 other info that might help us debug this:

  Possible unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(k-sk_lock-AF_INET);
                                lock(sk_lock-AF_INET);
                                lock(k-sk_lock-AF_INET);
   lock(sk_lock-AF_INET);

  *** DEADLOCK ***

 1 lock held by packetdrill/1071:
  #0: ffff8881b8346540 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0xfdf/0x1740
 ======================================================

The problem is caused by the blocking inet_wait_for_connect() releasing
and re-acquiring the msk socket lock while the subflow socket lock is
still held and the MPTCP socket requires that the msk socket lock must
be acquired before the subflow socket lock.

Address the issue always invoking tcp_sendmsg_fastopen() in an
unblocking manner, and later eventually complete the blocking
__inet_stream_connect() as needed.

Fixes: d98a82a6 ("mptcp: handle defer connect in mptcp_sendmsg")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The current MPTCP connect implementation duplicates a bit of inet
code and does not use nor provide a struct proto->connect callback,
which in turn will not fit the upcoming fastopen implementation.

Refactor such implementation to use the common helper, moving the
MPTCP-specific bits into mptcp_connect(). Additionally, avoid an
indirect call to the subflow connect callback.

Note that the fastopen call-path invokes mptcp_connect() while already
holding the subflow socket lock. Explicitly keep track of such path
via a new MPTCP-level flag and handle the locking accordingly.

Additionally, track the connect flags in a new msk field to allow
propagating them to the subflow inet_stream_connect call.

Fixes: d98a82a6 ("mptcp: handle defer connect in mptcp_sendmsg")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The mptcp_pm_nl_get_local_id() code assumes that the msk local address
is available at that point. For passive sockets, we initialize such
address at accept() time.

Depending on the running configuration and the user-space timing, a
passive MPJ subflow can join the msk socket before accept() completes.

In such case, the PM assigns a wrong local id to the MPJ subflow
and later PM netlink operations will end-up touching the wrong/unexpected
subflow.

All the above causes sporadic self-tests failures, especially when
the host is heavy loaded.

Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/308
Fixes: 01cacb00 ("mptcp: add netlink-based PM")
Fixes: d045b9eb ("mptcp: introduce implicit endpoints")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When a frame is sent using FDMA, the skb is mapped and then the mapped
address is given to an tx dcb that is different than the last used tx
dcb. Once the HW finish with this frame, it would generate an interrupt
and then the dcb can be reused and memory can be freed. For each dcb
there is an dcb buf that contains some meta-data(is used by PTP, is
it free). There is 1 to 1 relationship between dcb and dcb_buf.
The following issue was observed. That sometimes after changing the MTU
to allocate new tx dcbs and dcbs_buf, two frames were not
transmitted. The frames were not transmitted because when reloading the
tx dcbs, it was always presuming to use the first dcb but that was not
always happening. Because it could be that the last tx dcb used before
changing MTU was first dcb and then when it tried to get the next dcb it
would take dcb 1 instead of 0. Because it is supposed to take a
different dcb than the last used one. This can be fixed simply by
changing tx->last_in_use to -1 when the fdma is disabled to reload the
new dcb and dcbs_buff.
But there could be a different issue. For example, right after the frame
is sent, the MTU is changed. Now all the dcbs and dcbs_buf will be
cleared. And now get the interrupt from HW that it finished with the
frame. So when we try to clear the skb, it is not possible because we
lost all the dcbs_buf.
The solution here is to stop replacing the tx dcbs and dcbs_buf when
changing MTU because the TX doesn't care what is the MTU size, it is
only the RX that needs this information.

Fixes: 2ea1cbac ("net: lan966x: Update FDMA to change MTU.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20221021090711.3749009-1-horatiu.vultur@microchip.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

To keep backward compatibility we used to leave attribute parsing
to the family if no policy is specified. This becomes tedious as
we move to more strict validation. Families must define reject all
policies if they don't want any attributes accepted.

Piggy back on the resv_start_op field as the switchover point.
AFAICT only ethtool has added new commands since the resv_start_op
was defined, and it has per-op policies so this should be a no-op.

Nonetheless the patch should still go into v6.1 for consistency.

Link: https://lore.kernel.org/all/20221019125745.3f2e7659@kernel.org/
Link: https://lore.kernel.org/r/20221021193532.1511293-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The similar fix as commit 46cdedf2 ("ethtool: pse-pd: fix null-deref on
genl_info in dump") is also needed for ethtool eeprom.

Fixes: c781ff12 ("ethtool: Allow network drivers to dump arbitrary EEPROM data")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/5575919a2efc74cd9ad64021880afc3805c54166.1666362167.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf.

  The net-memcg fix stands out, the rest is very run-off-the-mill. Maybe
  I'm biased.

  Current release - regressions:

   - eth: fman: re-expose location of the MAC address to userspace,
     apparently some udev scripts depended on the exact value

  Current release - new code bugs:

   - bpf:
       - wait for busy refill_work when destroying bpf memory allocator
       - allow bpf_user_ringbuf_drain() callbacks to return 1
       - fix dispatcher patchable function entry to 5 bytes nop

  Previous releases - regressions:

   - net-memcg: avoid stalls when under memory pressure

   - tcp: fix indefinite deferral of RTO with SACK reneging

   - tipc: fix a null-ptr-deref in tipc_topsrv_accept

   - eth: macb: specify PHY PM management done by MAC

   - tcp: fix a signed-integer-overflow bug in tcp_add_backlog()

  Previous releases - always broken:

   - eth: amd-xgbe: SFP fixes and compatibility improvements

  Misc:

   - docs: netdev: offer performance feedback to contributors"

* tag 'net-6.1-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
  net-memcg: avoid stalls when under memory pressure
  tcp: fix indefinite deferral of RTO with SACK reneging
  tcp: fix a signed-integer-overflow bug in tcp_add_backlog()
  net: lantiq_etop: don't free skb when returning NETDEV_TX_BUSY
  net: fix UAF issue in nfqnl_nf_hook_drop() when ops_init() failed
  docs: netdev: offer performance feedback to contributors
  kcm: annotate data-races around kcm->rx_wait
  kcm: annotate data-races around kcm->rx_psock
  net: fman: Use physical address for userspace interfaces
  net/mlx5e: Cleanup MACsec uninitialization routine
  atlantic: fix deadlock at aq_nic_stop
  nfp: only clean `sp_indiff` when application firmware is unloaded
  amd-xgbe: add the bit rate quirk for Molex cables
  amd-xgbe: fix the SFP compliance codes check for DAC cables
  amd-xgbe: enable PLL_CTL for fixed PHY modes only
  amd-xgbe: use enums for mailbox cmd and sub_cmds
  amd-xgbe: Yellow carp devices do not need rrc
  bpf: Use __llist_del_all() whenever possbile during memory draining
  bpf: Wait for busy refill_work when destroying bpf memory allocator
  MAINTAINERS: add keyword match on PTP
  ...

Merge tag 'rcu-urgent.2022.10.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu

Pull RCU fix from Paul McKenney:
 "Fix a regression caused by commit bf95b2bc ("rcu: Switch polled
  grace-period APIs to ->gp_seq_polled"), which could incorrectly leave
  interrupts enabled after an early-boot call to synchronize_rcu().

  Such synchronize_rcu() calls must acquire leaf rcu_node locks in order
  to properly interact with polled grace periods, but the code did not
  take into account the possibility of synchronize_rcu() being invoked
  from the portion of the boot sequence during which interrupts are
  disabled.

  This commit therefore switches the lock acquisition and release from
  irq to irqsave/irqrestore"

* tag 'rcu-urgent.2022.10.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
  rcu: Keep synchronize_rcu() from enabling irqs in early boot

Merge tag 'linux-kselftest-kunit-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull KUnit fixes from Shuah Khan:
 "One single fix to update alloc_string_stream() callers to check for
  IS_ERR() instead of NULL to be in sync with alloc_string_stream()
  returning an ERR_PTR()"

* tag 'linux-kselftest-kunit-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  kunit: update NULL vs IS_ERR() tests

Merge tag 'linux-kselftest-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fixes from Shuah Khan:

 - futex, intel_pstate, kexec build fixes

 - ftrace dynamic_events dependency check fix

 - memory-hotplug fix to remove redundant warning from test report

* tag 'linux-kselftest-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/ftrace: fix dynamic_events dependency check
  selftests/memory-hotplug: Remove the redundant warning information
  selftests/kexec: fix build for ARCH=x86_64
  selftests/intel_pstate: fix build for ARCH=x86_64
  selftests/futex: fix build for clang

Pull pin control fixes from Linus Walleij:

 - Fix typos in UART1 and MMC in the Ingenic driver

 - A really well researched glitch bug fix to the Qualcomm driver that
   was tracked down and fixed by Dough Anderson from Chromium. Hats off
   for this one!

 - Revert two patches on the Xilinx ZynqMP driver: this needs a proper
   solution making use of firmware version information to adapt to
   different firmware releases

 - Fix interrupt triggers in the Ocelot driver

* tag 'pinctrl-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: ocelot: Fix incorrect trigger of the interrupt.
  Revert "dt-bindings: pinctrl-zynqmp: Add output-enable configuration"
  Revert "pinctrl: pinctrl-zynqmp: Add support for output-enable and bias-high-impedance"
  pinctrl: qcom: Avoid glitching lines when we first mux to output
  pinctrl: Ingenic: JZ4755 bug fixes

As Shakeel explains the commit under Fixes had the unintended
side-effect of no longer pre-loading the cached memory allowance.
Even tho we previously dropped the first packet received when
over memory limit - the consecutive ones would get thru by using
the cache. The charging was happening in batches of 128kB, so
we'd let in 128kB (truesize) worth of packets per one drop.

After the change we no longer force charge, there will be no
cache filling side effects. This causes significant drops and
connection stalls for workloads which use a lot of page cache,
since we can't reclaim page cache under GFP_NOWAIT.

Some of the latency can be recovered by improving SACK reneg
handling but nowhere near enough to get back to the pre-5.15
performance (the application I'm experimenting with still
sees 5-10x worst latency).

Apply the suggested workaround of using GFP_ATOMIC. We will now
be more permissive than previously as we'll drop _no_ packets
in softirq when under pressure. But I can't think of any good
and simple way to address that within networking.

Link: https://lore.kernel.org/all/20221012163300.795e7b86@kernel.org/Suggested-by: Shakeel Butt <shakeelb@google.com>
Fixes: 4b1327be ("net-memcg: pass in gfp_t mask to mem_cgroup_charge_skmem()")
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Link: https://lore.kernel.org/r/20221021160304.1362511-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This commit fixes a bug that can cause a TCP data sender to repeatedly
defer RTOs when encountering SACK reneging.

The bug is that when we're in fast recovery in a scenario with SACK
reneging, every time we get an ACK we call tcp_check_sack_reneging()
and it can note the apparent SACK reneging and rearm the RTO timer for
srtt/2 into the future. In some SACK reneging scenarios that can
happen repeatedly until the receive window fills up, at which point
the sender can't send any more, the ACKs stop arriving, and the RTO
fires at srtt/2 after the last ACK. But that can take far too long
(O(10 secs)), since the connection is stuck in fast recovery with a
low cwnd that cannot grow beyond ssthresh, even if more bandwidth is
available.

This fix changes the logic in tcp_check_sack_reneging() to only rearm
the RTO timer if data is cumulatively ACKed, indicating forward
progress. This avoids this kind of nearly infinite loop of RTO timer
re-arming. In addition, this meets the goals of
tcp_check_sack_reneging() in handling Windows TCP behavior that looks
temporarily like SACK reneging but is not really.

Many thanks to Jakub Kicinski and Neil Spring, who reported this issue
and provided critical packet traces that enabled root-causing this
issue. Also, many thanks to Jakub Kicinski for testing this fix.

Fixes: 5ae344c9 ("tcp: reduce spurious retransmits due to transient SACK reneging")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Reported-by: Neil Spring <ntspring@fb.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Tested-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221021170821.1093930-1-ncardwell.kernel@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Alexei Starovoitov says:

====================
pull-request: bpf 2022-10-23

We've added 7 non-merge commits during the last 18 day(s) which contain
a total of 8 files changed, 69 insertions(+), 5 deletions(-).

The main changes are:

1) Wait for busy refill_work when destroying bpf memory allocator, from Hou.

2) Allow bpf_user_ringbuf_drain() callbacks to return 1, from David.

3) Fix dispatcher patchable function entry to 5 bytes nop, from Jiri.

4) Prevent decl_tag from being referenced in func_proto, from Stanislav.

* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  bpf: Use __llist_del_all() whenever possbile during memory draining
  bpf: Wait for busy refill_work when destroying bpf memory allocator
  bpf: Fix dispatcher patchable function entry to 5 bytes nop
  bpf: prevent decl_tag from being referenced in func_proto
  selftests/bpf: Add reproducer for decl_tag in func_proto return type
  selftests/bpf: Make bpf_user_ringbuf_drain() selftest callback return 1
  bpf: Allow bpf_user_ringbuf_drain() callbacks to return 1
====================

Link: https://lore.kernel.org/r/20221023192244.81137-1-alexei.starovoitov@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The type of sk_rcvbuf and sk_sndbuf in struct sock is int, and
in tcp_add_backlog(), the variable limit is caculated by adding
sk_rcvbuf, sk_sndbuf and 64 * 1024, it may exceed the max value
of int and overflow. This patch reduces the limit budget by
halving the sndbuf to solve this issue since ACK packets are much
smaller than the payload.

Fixes: c9c33212 ("tcp: add tcp_add_backlog()")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ndo_start_xmit() method must not free skb when returning
NETDEV_TX_BUSY, since caller is going to requeue freed skb.

Fixes: 504d4721 ("MIPS: Lantiq: Add ethernet driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the ops_init() interface is invoked to initialize the net, but
ops->init() fails, data is released. However, the ptr pointer in
net->gen is invalid. In this case, when nfqnl_nf_hook_drop() is invoked
to release the net, invalid address access occurs.

The process is as follows:
setup_net()
	ops_init()
		data = kzalloc(...)   ---> alloc "data"
		net_assign_generic()  ---> assign "date" to ptr in net->gen
		...
		ops->init()           ---> failed
		...
		kfree(data);          ---> ptr in net->gen is invalid
	...
	ops_exit_list()
		...
		nfqnl_nf_hook_drop()
			*q = nfnl_queue_pernet(net) ---> q is invalid

The following is the Call Trace information:
BUG: KASAN: use-after-free in nfqnl_nf_hook_drop+0x264/0x280
Read of size 8 at addr ffff88810396b240 by task ip/15855
Call Trace:
<TASK>
dump_stack_lvl+0x8e/0xd1
print_report+0x155/0x454
kasan_report+0xba/0x1f0
nfqnl_nf_hook_drop+0x264/0x280
nf_queue_nf_hook_drop+0x8b/0x1b0
__nf_unregister_net_hook+0x1ae/0x5a0
nf_unregister_net_hooks+0xde/0x130
ops_exit_list+0xb0/0x170
setup_net+0x7ac/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK>

Allocated by task 15855:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
__kasan_kmalloc+0xa1/0xb0
__kmalloc+0x49/0xb0
ops_init+0xe7/0x410
setup_net+0x5aa/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0

Freed by task 15855:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x40
____kasan_slab_free+0x155/0x1b0
slab_free_freelist_hook+0x11b/0x220
__kmem_cache_free+0xa4/0x360
ops_init+0xb9/0x410
setup_net+0x5aa/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0

Fixes: f875bae0 ("net: Automatically allocate per namespace data.")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of us gotten used to producing large quantities of peer feedback
at work, every 3 or 6 months. Extending the same courtesy to community
members seems like a logical step. It may be hard for some folks to
get validation of how important their work is internally, especially
at smaller companies which don't employ many kernel experts.

The concept of "peer feedback" may be a hyperscaler / silicon valley
thing so YMMV. Hopefully we can build more context as we go.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
kcm: annotate data-races

This series address two different syzbot reports for KCM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

kcm->rx_psock can be read locklessly in kcm_rfree().
Annotate the read and writes accordingly.

syzbot reported:

BUG: KCSAN: data-race in kcm_rcv_strparser / kcm_rfree

write to 0xffff88810784e3d0 of 1 bytes by task 1823 on cpu 1:
reserve_rx_kcm net/kcm/kcmsock.c:283 [inline]
kcm_rcv_strparser+0x250/0x3a0 net/kcm/kcmsock.c:363
__strp_recv+0x64c/0xd20 net/strparser/strparser.c:301
strp_recv+0x6d/0x80 net/strparser/strparser.c:335
tcp_read_sock+0x13e/0x5a0 net/ipv4/tcp.c:1703
strp_read_sock net/strparser/strparser.c:358 [inline]
do_strp_work net/strparser/strparser.c:406 [inline]
strp_work+0xe8/0x180 net/strparser/strparser.c:415
process_one_work+0x3d3/0x720 kernel/workqueue.c:2289
worker_thread+0x618/0xa70 kernel/workqueue.c:2436
kthread+0x1a9/0x1e0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306

read to 0xffff88810784e3d0 of 1 bytes by task 17869 on cpu 0:
kcm_rfree+0x121/0x220 net/kcm/kcmsock.c:181
skb_release_head_state+0x8e/0x160 net/core/skbuff.c:841
skb_release_all net/core/skbuff.c:852 [inline]
__kfree_skb net/core/skbuff.c:868 [inline]
kfree_skb_reason+0x5c/0x260 net/core/skbuff.c:891
kfree_skb include/linux/skbuff.h:1216 [inline]
kcm_recvmsg+0x226/0x2b0 net/kcm/kcmsock.c:1161
____sys_recvmsg+0x16c/0x2e0
___sys_recvmsg net/socket.c:2743 [inline]
do_recvmmsg+0x2f1/0x710 net/socket.c:2837
__sys_recvmmsg net/socket.c:2916 [inline]
__do_sys_recvmmsg net/socket.c:2939 [inline]
__se_sys_recvmmsg net/socket.c:2932 [inline]
__x64_sys_recvmmsg+0xde/0x160 net/socket.c:2932
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

value changed: 0x01 -> 0x00

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 17869 Comm: syz-executor.2 Not tainted 6.1.0-rc1-syzkaller-00010-gbb1a1146-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022

Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kcm->rx_psock can be read locklessly in kcm_rfree().
Annotate the read and writes accordingly.

We do the same for kcm->rx_wait in the following patch.

syzbot reported:
BUG: KCSAN: data-race in kcm_rfree / unreserve_rx_kcm

write to 0xffff888123d827b8 of 8 bytes by task 2758 on cpu 1:
unreserve_rx_kcm+0x72/0x1f0 net/kcm/kcmsock.c:313
kcm_rcv_strparser+0x2b5/0x3a0 net/kcm/kcmsock.c:373
__strp_recv+0x64c/0xd20 net/strparser/strparser.c:301
strp_recv+0x6d/0x80 net/strparser/strparser.c:335
tcp_read_sock+0x13e/0x5a0 net/ipv4/tcp.c:1703
strp_read_sock net/strparser/strparser.c:358 [inline]
do_strp_work net/strparser/strparser.c:406 [inline]
strp_work+0xe8/0x180 net/strparser/strparser.c:415
process_one_work+0x3d3/0x720 kernel/workqueue.c:2289
worker_thread+0x618/0xa70 kernel/workqueue.c:2436
kthread+0x1a9/0x1e0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306

read to 0xffff888123d827b8 of 8 bytes by task 5859 on cpu 0:
kcm_rfree+0x14c/0x220 net/kcm/kcmsock.c:181
skb_release_head_state+0x8e/0x160 net/core/skbuff.c:841
skb_release_all net/core/skbuff.c:852 [inline]
__kfree_skb net/core/skbuff.c:868 [inline]
kfree_skb_reason+0x5c/0x260 net/core/skbuff.c:891
kfree_skb include/linux/skbuff.h:1216 [inline]
kcm_recvmsg+0x226/0x2b0 net/kcm/kcmsock.c:1161
____sys_recvmsg+0x16c/0x2e0
___sys_recvmsg net/socket.c:2743 [inline]
do_recvmmsg+0x2f1/0x710 net/socket.c:2837
__sys_recvmmsg net/socket.c:2916 [inline]
__do_sys_recvmmsg net/socket.c:2939 [inline]
__se_sys_recvmmsg net/socket.c:2932 [inline]
__x64_sys_recvmmsg+0xde/0x160 net/socket.c:2932
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

value changed: 0xffff88812971ce00 -> 0x0000000000000000

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 5859 Comm: syz-executor.3 Not tainted 6.0.0-syzkaller-12189-g19d17ab7-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022

Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before 262f2b78 ("net: fman: Map the base address once"), the
physical address of the MAC was exposed to userspace in two places: via
sysfs and via SIOCGIFMAP. While this is not best practice, it is an
external ABI which is in use by userspace software.

The aforementioned commit inadvertently modified these addresses and
made them virtual. This constitutes and ABI break.  Additionally, it
leaks the kernel's memory layout to userspace. Partially revert that
commit, reintroducing the resource back into struct mac_device, while
keeping the intended changes (the rework of the address mapping).

Fixes: 262f2b78 ("net: fman: Map the base address once")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mlx5e_macsec_cleanup() routine has NULL pointer dereferencing if mlx5
device doesn't support MACsec (priv->macsec will be NULL).

While at it delete comment line, assignment and extra blank lines, so fix
everything in one patch.

Fixes: 1f53da67 ("net/mlx5e: Create advanced steering operation (ASO) object for MACsec")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NIC is stopped with rtnl_lock held, and during the stop it cancels the
'service_task' work and free irqs.

However, if CONFIG_MACSEC is set, rtnl_lock is acquired both from
aq_nic_service_task and aq_linkstate_threaded_isr. Then a deadlock
happens if aq_nic_stop tries to cancel/disable them when they've already
started their execution.

As the deadlock is caused by rtnl_lock, it causes many other processes
to stall, not only atlantic related stuff.

Fix it by introducing a mutex that protects each NIC's macsec related
data, and locking it instead of the rtnl_lock from the service task and
the threaded IRQ.

Before this patch, all macsec data was protected with rtnl_lock, but
maybe not all of it needs to be protected. With this new mutex, further
efforts can be made to limit the protected data only to that which
requires it. However, probably it doesn't worth it because all macsec's
data accesses are infrequent, and almost all are done from macsec_ops
or ethtool callbacks, called holding rtnl_lock, so macsec_mutex won't
never be much contended.

The issue appeared repeteadly attaching and deattaching the NIC to a
bond interface. Doing that after this patch I cannot reproduce the bug.

Fixes: 62c1c2e6 ("net: atlantic: MACSec offload skeleton")
Reported-by: Li Liang <liali@redhat.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Back in 2014, the LQI was saved in the skb control buffer (skb->cb, or
mac_cb(skb)) without any actual reset of this area prior to its use.

As part of a useful rework of the use of this region, 32edc40a
("ieee802154: change _cb handling slightly") introduced mac_cb_init() to
basically memset the cb field to 0. In particular, this new function got
called at the beginning of mac802154_parse_frame_start(), right before
the location where the buffer got actually filled.

What went through unnoticed however, is the fact that the very first
helper called by device drivers in the receive path already used this
area to save the LQI value for later extraction. Resetting the cb field
"so late" led to systematically zeroing the LQI.

If we consider the reset of the cb field needed, we can make it as soon
as we get an skb from a device driver, right before storing the LQI,
as is the very first time we need to write something there.

Cc: stable@vger.kernel.org
Fixes: 32edc40a ("ieee802154: change _cb handling slightly")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20221020142535.1038885-1-miquel.raynal@bootlin.comSigned-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

Pull kvm fixes from Paolo Bonzini:
 "RISC-V:

   - Fix compilation without RISCV_ISA_ZICBOM

   - Fix kvm_riscv_vcpu_timer_pending() for Sstc

  ARM:

   - Fix a bug preventing restoring an ITS containing mappings for very
     large and very sparse device topology

   - Work around a relocation handling error when compiling the nVHE
     object with profile optimisation

   - Fix for stage-2 invalidation holding the VM MMU lock for too long
     by limiting the walk to the largest block mapping size

   - Enable stack protection and branch profiling for VHE

   - Two selftest fixes

  x86:

   - add compat implementation for KVM_X86_SET_MSR_FILTER ioctl

  selftests:

   - synchronize includes between include/uapi and tools/include/uapi"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  tools: include: sync include/api/linux/kvm.h
  KVM: x86: Add compat handler for KVM_X86_SET_MSR_FILTER
  KVM: x86: Copy filter arg outside kvm_vm_ioctl_set_msr_filter()
  kvm: Add support for arch compat vm ioctls
  RISC-V: KVM: Fix kvm_riscv_vcpu_timer_pending() for Sstc
  RISC-V: Fix compilation without RISCV_ISA_ZICBOM
  KVM: arm64: vgic: Fix exit condition in scan_its_table()
  KVM: arm64: nvhe: Fix build with profile optimization
  KVM: selftests: Fix number of pages for memory slot in memslot_modification_stress_test
  KVM: arm64: selftests: Fix multiple versions of GIC creation
  KVM: arm64: Enable stack protection and branch profiling for VHE
  KVM: arm64: Limit stage2_apply_range() batch size to largest block
  KVM: arm64: Work out supported block level at compile time

This reverts commit 72a95859.

It broke reboots on big-endian MIPS and MIPS64 malta QEMU instances,
which use the syscon driver.  Little-endian is not effected, which means
likely it's important to handle regmap_get_val_endian() in this function
after all.

Fixes: 72a95859 ("mfd: syscon: Remove repetition of the regmap_get_val_endian()")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit bfca3dd3 ("kernel/utsname_sysctl.c: print kernel arch") added
a new entry to the uts_kern_table[] array, but didn't update the
UTS_PROC_xyz enumerators of older entries, breaking anything that used
them.

Which is admittedly not many cases: it's really just the two uses of
uts_proc_notify() in kernel/sys.c.  But apparently journald-systemd
actually uses this to detect hostname changes.
Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Fixes: bfca3dd3 ("kernel/utsname_sysctl.c: print kernel arch")
Link: https://lore.kernel.org/lkml/0c2b92a6-0f25-9538-178f-eee3b06da23f@secunet.com/
Link: https://linux-regtracking.leemhuis.info/regzbot/regression/0c2b92a6-0f25-9538-178f-eee3b06da23f@secunet.com/
Cc: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull perf fixes from Borislav Petkov:

 - Fix raw data handling when perf events are used in bpf

 - Rework how SIGTRAPs get delivered to events to address a bunch of
   problems with it. Add a selftest for that too

* tag 'perf_urgent_for_v6.1_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  bpf: Fix sample_flags for bpf_perf_event_output
  selftests/perf_events: Add a SIGTRAP stress test with disables
  perf: Fix missing SIGTRAPs