To cleanup the code, this patch adds a function to write the UGCTRL2
register.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

On rk3288-veyron devices on Chrome OS it was found that plugging in an
Arduino-based USB device could cause the system to lockup, especially
if the CPU Frequency was at one of the slower operating points (like
100 MHz / 200 MHz).

Upon tracing, I found that the following was happening:
* The USB device (full speed) was connected to a high speed hub and
  then to the rk3288.  Thus, we were dealing with split transactions,
  which is all handled in software on dwc2.
* Userspace was initiating a BULK IN transfer
* When we sent the SSPLIT (to start the split transaction), we got an
  ACK.  Good.  Then we issued the CSPLIT.
* When we sent the CSPLIT, we got back a NAK.  We immediately (from
  the interrupt handler) started to retry and sent another SSPLIT.
* The device kept NAKing our CSPLIT, so we kept ping-ponging between
  sending a SSPLIT and a CSPLIT, each time sending from the interrupt
  handler.
* The handling of the interrupts was (because of the low CPU speed and
  the inefficiency of the dwc2 interrupt handler) was actually taking
  _longer_ than it took the other side to send the ACK/NAK.  Thus we
  were _always_ in the USB interrupt routine.
* The fact that USB interrupts were always going off was preventing
  other things from happening in the system.  This included preventing
  the system from being able to transition to a higher CPU frequency.

As I understand it, there is no requirement to retry super quickly
after a NAK, we just have to retry sometime in the future.  Thus one
solution to the above is to just add a delay between getting a NAK and
retrying the transmission.  If this delay is sufficiently long to get
out of the interrupt routine then the rest of the system will be able
to make forward progress.  Even a 25 us delay would probably be
enough, but we'll be extra conservative and try to delay 1 ms (the
exact amount depends on HZ and the accuracy of the jiffy and how close
the current jiffy is to ticking, but could be as much as 20 ms or as
little as 1 ms).

Presumably adding a delay like this could impact the USB throughput,
so we only add the delay with repeated NAKs.

NOTE: Upon further testing of a pl2303 serial adapter, I found that
this fix may help with problems there.  Specifically I found that the
pl2303 serial adapters tend to respond with a NAK when they have
nothing to say and thus we end with this same sequence.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The dwc2 USB controller in Stratix10 has an additional ECC reset bit that
needs to get de-asserted in order for the controller to work properly.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch uses usbhs_pipe_clear_without_sequence() instead of
usbhsf_fifo_clear() because usbhsf_fifo_clear() may not clear the pipe
buffer completely. This patch also changes the clearing condition from
DMA only to both DMA and PIO.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds usbhs_pipe_clear_without_sequence() function.
The controller has the pipe buffer and the PIPEnCTR.ACLRM can clear
it completely. But, it's also clear the data sequence. So, the driver
needs to get the sequence before.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The datasheet doesn't mention that needs to poll of FRDY is set or not.
So, this patch removes such handling in the usbhsf_fifo_barrier().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Factor out the guts of usb charger initialization into usb_charger_init()
function, to make the usb_add_extcon() only do the extcon related things.
Meanwhile we also should initialize the USB charger before registering
the extcon device, in case the extcon notification was issued earlier than
usb charger initialization.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Some platforms (e.g. TI's DRA7 USB2 instance) have more trouble
with the metastability workaround as it supports only
a High-Speed PHY and the PHY can enter into an Erratic state [1]
when the controller is set in SuperSpeed mode as part of
the metastability workaround.

This causes upto 2 seconds delay in enumeration on DRA7's USB2
instance in gadget mode.

If these platforms can be better off without the workaround,
provide a device tree property to suggest that so the workaround
is avoided.

[1] Device mode enumeration trace showing PHY Erratic Error.
     irq/90-dwc3-969   [000] d...    52.323145: dwc3_event: event (00000901): Erratic Error [U0]
     irq/90-dwc3-969   [000] d...    52.560646: dwc3_event: event (00000901): Erratic Error [U0]
     irq/90-dwc3-969   [000] d...    52.798144: dwc3_event: event (00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The UDC core ensures that .udc_set_speed() is called with
a speed that is a minimum of the max speeds supported
by the gadget function driver and the UDC driver.

We can now use the speed argument as is.

Get rid of the debug print as that condition will never happen.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There will never be a case when gadget.speed isn't already
USB_SPEED_FULL if connection is not USB-3 and gadget.speed
is not USB_SPEED_HIGH or USB_SPEED_LOW.

Remove the unnecessary code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add a jump target so that a specific error message is stored only once
at the end of this function implementation.
Replace two calls of the function "dev_err" by goto statements.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Variable is_short is set to zero but this value is never read as it is
overwritten with a new value later on, hence it is a redundant
assignment and can be removed.  Pointer dev is assigned a value that
is not read and it is updated a few statements later, this too is
redundant and can be removed. Cleans up clan warnings:

drivers/usb/gadget/udc/pxa27x_udc.c:986:3: warning: Value stored
to 'is_short' is never read
drivers/usb/gadget/udc/pxa27x_udc.c:1141:2: warning: Value stored
to 'dev' is never read
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pointer udc is assigned but never read, hence it is redundant and
can be removed. Cleans up clang warning:

drivers/usb/gadget/udc/udc-xilinx.c:974:2: warning: Value stored
to 'udc' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The variable value is being assigned to zero but that value is never being
read.  Either value is being reassigned in the following if condition, or
it is never read and the function returns. In both cases the assignment is
redundant and can be removed. Cleans up clang warning:

drivers/usb/gadget/legacy/inode.c:1473:4: warning: Value stored to 'value'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Trival fix to spelling mistake in ERR message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Silences the following warnings:
drivers/usb/gadget/function/f_fs.c:1253:37: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/gadget/function/f_fs.c:1253:37:    expected void [noderef] <asn:1>*to
drivers/usb/gadget/function/f_fs.c:1253:37:    got void *<noident>
drivers/usb/gadget/function/f_fs.c:2322:23: warning: cast to restricted __le32
drivers/usb/gadget/function/f_fs.c:2876:38: warning: cast to restricted __le32
drivers/usb/gadget/function/f_fs.c:272:12: warning: context imbalance in '__ffs_ep0_queue_wait' - unexpected unlock
drivers/usb/gadget/function/f_fs.c:450:17: warning: context imbalance in 'ffs_ep0_write' - different lock contexts for basic block
drivers/usb/gadget/function/f_fs.c:490:24: warning: context imbalance in '__ffs_ep0_read_events' - unexpected unlock
drivers/usb/gadget/function/f_fs.c:496:16: warning: context imbalance in 'ffs_ep0_read' - different lock contexts for basic block

Also, add an "unlocks spinlock" comment for consistency with existing ones.
No behaviour change is intended.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The kernel FIFO implementation, kfifo, provides interfaces to manipulate
a first-in-first-out circular buffer.  Use kfifo instead of the homemade
one to make the code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Fixes the following warnings:
drivers/usb/dwc3/io.h:43:31: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/io.h:43:31:    expected void *base
drivers/usb/dwc3/io.h:43:31:    got void [noderef] <asn:2>*
drivers/usb/dwc3/io.h:62:32: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/io.h:62:32:    expected void *base
drivers/usb/dwc3/io.h:62:32:    got void [noderef] <asn:2>*

This fixes the noisiest ones as they get emitted multiple times.
A few warnings remain, for which the proper fix is less clear.

No behaviour change is expected.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This allows to identify transfer request, if more than one are in queue.

This is allowed by usb_ep_queue : "Any endpoint
(except control endpoints like ep0) may have more than one transfer
request queued; they complete in FIFO order."

For example with adb gadget with function fs :

     <-transport-225   [002] d..1    47.136641: usb_ep_queue: ep1out: req ffffffc07b93ef10 length 0/24 sgs 0/0 stream 0 zsI status -115 --> 0
     ->transport-224   [000] d..1    47.153947: usb_ep_queue: ep1in: req ffffffc07c0def10 length 0/24 sgs 0/0 stream 0 zsI status -115 --> 0
              sh-452   [000] d.h2    47.153984: usb_gadget_giveback_request: ep1in: req ffffffc07c0def10 length 24/24 sgs 0/0 stream 0 zsI status 0 --> 0
              sh-452   [000] d.h.    47.154305: usb_gadget_giveback_request: ep1out: req ffffffc07b93ef10 length 24/24 sgs 0/0 stream 0 zsI status 0 --> 0
     <-transport-225   [002] d..1    47.154363: usb_ep_queue: ep1out: req ffffffc07b93ef10 length 0/21 sgs 0/0 stream 0 zsI status -115 --> 0
              sh-452   [000] d.h.    47.154378: usb_gadget_giveback_request: ep1out: req ffffffc07b93ef10 length 21/21 sgs 0/0 stream 0 zsI status 0 --> 0
     <-transport-225   [002] d..1    47.154463: usb_ep_queue: ep1out: req ffffffc07b93ef10 length 0/24 sgs 0/0 stream 0 zsI status -115 --> 0
     ->transport-224   [000] d..1    47.154583: usb_ep_queue: ep1in: req ffffffc07c0def10 length 0/24 sgs 0/0 stream 0 zsI status -115 --> 0
              sh-452   [000] d.h2    47.154600: usb_gadget_giveback_request: ep1in: req ffffffc07c0def10 length 24/24 sgs 0/0 stream 0 zsI status 0 --> 0
     ->transport-224   [000] d..1    47.164863: usb_ep_queue: ep1in: req ffffffc07c0def10 length 0/24 sgs 0/0 stream 0 zsI status -115 --> 0
     ->transport-224   [000] d.h1    47.164887: usb_gadget_giveback_request: ep1in: req ffffffc07c0def10 length 24/24 sgs 0/0 stream 0 zsI status 0 --> 0
     ->transport-224   [000] d..1    47.164907: usb_ep_queue: ep1in: req ffffffc07c0def10 length 0/122 sgs 0/0 stream 0 zsI status -115 --> 0
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead of keeping our own isoch_delay, let's make use of the newly
introduced isoch_delay member in struct usb_gadget. The benefit here
is that we would be using a generic "API" which other UDCs can use,
resulting in a common setup for gadget drivers who may be interested
in Isoch Delay value.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Whenever a USB host issues a Set Isoch Delay request, we should cache
the result so relevant gadget drivers can make use of the value for
calculating how many uFrames ahead a transfer should be queued.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We were missing U1, U2 and LTM Enable features. Let's decode them.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

HPFS does not set SB_I_VERSION and does not use the i_version counter
internally.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Mikulas Patocka <mikulas@twibright.com>
Reviewed-by: Mikulas Patocka <mikulas@twibright.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sign_extend32 counts the sign bit parameter from 0, not from 1.  So we
have to use "11" for 12th bit, not "12".

This mistake means we have not allowed negative op and cmp args since
commit 30d6e0a4 ("futex: Remove duplicated code and fix undefined
behaviour") till now.

Fixes: 30d6e0a4 ("futex: Remove duplicated code and fix undefined behaviour")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull btrfs fixes from David Sterba:
 "This contains a few fixes (error handling, quota leak, FUA vs
  nobarrier mount option).

  There's one one worth mentioning separately - an off-by-one fix that
  leads to overwriting first byte of an adjacent page with 0, out of
  bounds of the memory allocated by an ioctl. This is under a privileged
  part of the ioctl, can be triggerd in some subvolume layouts"

* tag 'for-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: Fix possible off-by-one in btrfs_search_path_in_tree
  Btrfs: disable FUA if mounted with nobarrier
  btrfs: fix missing error return in btrfs_drop_snapshot
  btrfs: handle errors while updating refcounts in update_ref_for_cow
  btrfs: Fix quota reservation leak on preallocated files

Pull ARM SoC fixes from Olof Johansson:

 - A revert of all SCPI changes from the 4.15 merge window. They had
   regressions on the Amlogic platforms, and the submaintainer isn't
   around to fix these bugs due to vacation, etc. So we agreed to revert
   and revisit in next release cycle.

 - A series fixing a number of bugs for ARM CCN interconnect, around
   module unload, smp_processor_id() in preemptable context, and fixing
   some memory allocation failure checks.

 - A handful of devicetree fixes for different platforms, fixing
   warnings and errors that were previously ignored by the compiler.

 - The usual set of mostly minor fixes for different platforms.

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
  ARM64: dts: meson-gx: fix UART pclk clock name
  ARM: omap2: hide omap3_save_secure_ram on non-OMAP3 builds
  arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv
  ARM: dts: Fix dm814x missing phy-cells property
  ARM: dts: Fix elm interrupt compiler warning
  bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
  bus: arm-cci: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Simplify code
  bus: arm-ccn: Check memory allocation failure
  bus: arm-ccn: constify attribute_group structures.
  firmware: arm_scpi: Revert updates made during v4.15 merge window
  arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv
  arm64: dts: sort vendor subdirectories in Makefile alphabetically
  meson-gx-socinfo: Fix package id parsing
  ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
  ARM: dts: meson: fix the memory region of the GPIO interrupt controller
  ARM: dts: meson: correct the sort order for the the gpio_intc node
  MAINTAINERS: exclude other Socionext SoC DT files from ARM/UNIPHIER entry
  arm64: dts: uniphier: remove unnecessary interrupt-parent
  ...

Pull KVM fixes from Radim Krčmář:
 "ARM:
   - A number of issues in the vgic discovered using SMATCH
   - A bit one-off calculation in out stage base address mask (32-bit
     and 64-bit)
   - Fixes to single-step debugging instructions that trap for other
     reasons such as MMMIO aborts
   - Printing unavailable hyp mode as error
   - Potential spinlock deadlock in the vgic
   - Avoid calling vgic vcpu free more than once
   - Broken bit calculation for big endian systems

 s390:
   - SPDX tags
   - Fence storage key accesses from problem state
   - Make sure that irq_state.flags is not used in the future

  x86:
   - Intercept port 0x80 accesses to prevent host instability (CVE)
   - Use userspace FPU context for guest FPU (mainly an optimization
     that fixes a double use of kernel FPU)
   - Do not leak one page per module load
   - Flush APIC page address cache from MMU invalidation notifiers"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
  KVM: x86: fix APIC page invalidation
  KVM: s390: Fix skey emulation permission check
  KVM: s390: mark irq_state.flags as non-usable
  KVM: s390: Remove redundant license text
  KVM: s390: add SPDX identifiers to the remaining files
  KVM: VMX: fix page leak in hardware_setup()
  KVM: VMX: remove I/O port 0x80 bypass on Intel hosts
  x86,kvm: remove KVM emulator get_fpu / put_fpu
  x86,kvm: move qemu/guest FPU switching out to vcpu_run
  KVM: arm/arm64: Fix broken GICH_ELRSR big endian conversion
  KVM: arm/arm64: kvm_arch_destroy_vm cleanups
  KVM: arm/arm64: Fix spinlock acquisition in vgic_set_owner
  kvm: arm: don't treat unavailable HYP mode as an error
  KVM: arm/arm64: Avoid attempting to load timer vgic state without a vgic
  kvm: arm64: handle single-step of hyp emulated mmio instructions
  kvm: arm64: handle single-step during SError exceptions
  kvm: arm64: handle single-step of userspace mmio instructions
  kvm: arm64: handle single-stepping trapped instructions
  KVM: arm/arm64: debug: Introduce helper for single-step
  arm: KVM: Fix VTTBR_BADDR_MASK BUG_ON off-by-one
  ...

* fixes:
  ARM64: dts: meson-gx: fix UART pclk clock name
  ARM: dts: Fix dm814x missing phy-cells property
  ARM: dts: Fix elm interrupt compiler warning
  bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
  bus: arm-cci: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Simplify code
  bus: arm-ccn: Check memory allocation failure
  bus: arm-ccn: constify attribute_group structures.
  meson-gx-socinfo: Fix package id parsing
  ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
  ARM: dts: meson: fix the memory region of the GPIO interrupt controller
  ARM: dts: meson: correct the sort order for the the gpio_intc node

Merge tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes

Amlogic fixes for v4.15-rc
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo

* tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gx: fix UART pclk clock name
  meson-gx-socinfo: Fix package id parsing
  ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
  ARM: dts: meson: fix the memory region of the GPIO interrupt controller
  ARM: dts: meson: correct the sort order for the the gpio_intc node
Signed-off-by: Olof Johansson <olof@lixom.net>

bus: ARM CCN and CCI PMU driver fixes

This is a bunch of fixes CCN and (guest starring this time) CCI drivers.

* Check for potential of failed allocation for the driver name string
* Manage CPU ID properly at allocation (both CCN and CCI)
* Fix module unload warnings related to objects release order
* Small improvements like using allocating printfs and proper
  attributes constification

The one fixing potential issues have been cc-ed to stable.

* tag 'ccn/fixes-for-4.15' of git://git.linaro.org/people/pawel.moll/linux:
  bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
  bus: arm-cci: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Simplify code
  bus: arm-ccn: Check memory allocation failure
  bus: arm-ccn: constify attribute_group structures.
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Two fixes for dts compiler warnings

These recently started showing up with better dtc checks being
introduced.

* tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: Fix dm814x missing phy-cells property
  ARM: dts: Fix elm interrupt compiler warning
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'keys-fixes-20171208' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs into keys-for-linus

Assorted fixes for keyrings, ASN.1, X.509 and PKCS#7.

Commit 4675ff05 ("kmemcheck: rip it out") has removed the code but
for some reason SPDX header stayed in place.  This looks like a rebase
mistake in the mmotm tree or the merge mistake.  Let's drop those
leftovers as well.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) CAN fixes from Martin Kelly (cancel URBs properly in all the CAN usb
    drivers).

 2) Revert returning -EEXIST from __dev_alloc_name() as this propagates
    to userspace and broke some apps. From Johannes Berg.

 3) Fix conn memory leaks and crashes in TIPC, from Jon Malloc and Cong
    Wang.

 4) Gianfar MAC can't do EEE so don't advertise it by default, from
    Claudiu Manoil.

 5) Relax strict netlink attribute validation, but emit a warning. From
    David Ahern.

 6) Fix regression in checksum offload of thunderx driver, from Florian
    Westphal.

 7) Fix UAPI bpf issues on s390, from Hendrik Brueckner.

 8) New card support in iwlwifi, from Ihab Zhaika.

 9) BBR congestion control bug fixes from Neal Cardwell.

10) Fix port stats in nfp driver, from Pieter Jansen van Vuuren.

11) Fix leaks in qualcomm rmnet, from Subash Abhinov Kasiviswanathan.

12) Fix DMA API handling in sh_eth driver, from Thomas Petazzoni.

13) Fix spurious netpoll warnings in bnxt_en, from Calvin Owens.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
  net: mvpp2: fix the RSS table entry offset
  tcp: evaluate packet losses upon RTT change
  tcp: fix off-by-one bug in RACK
  tcp: always evaluate losses in RACK upon undo
  tcp: correctly test congestion state in RACK
  bnxt_en: Fix sources of spurious netpoll warnings
  tcp_bbr: reset long-term bandwidth sampling on loss recovery undo
  tcp_bbr: reset full pipe detection on loss recovery undo
  tcp_bbr: record "full bw reached" decision in new full_bw_reached bit
  sfc: pass valid pointers from efx_enqueue_unwind
  gianfar: Disable EEE autoneg by default
  tcp: invalidate rate samples during SACK reneging
  can: peak/pcie_fd: fix potential bug in restarting tx queue
  can: usb_8dev: cancel urb on -EPIPE and -EPROTO
  can: kvaser_usb: cancel urb on -EPIPE and -EPROTO
  can: esd_usb2: cancel urb on -EPIPE and -EPROTO
  can: ems_usb: cancel urb on -EPIPE and -EPROTO
  can: mcba_usb: cancel urb on -EPROTO
  usbnet: fix alignment for frames with no ethernet header
  tcp: use current time in tcp_rcv_space_adjust()
  ...

Pull media fixes from Mauro Carvalho Chehab:

 "A series of fixes for the media subsytem:

   - The largest amount of fixes in this series is with regards to
     comments that aren't kernel-doc, but start with "/**".

     A new check added for 4.15 makes it to produce a *huge* amount of
     new warnings (I'm compiling here with W=1). Most of the patches in
     this series fix those.

     No code changes - just comment changes at the source files

   - rc: some fixed in order to better handle RC repetition codes

   - v4l-async: use the v4l2_dev from the root notifier when matching
     sub-devices

   - v4l2-fwnode: Check subdev count after checking port

   - ov 13858 and et8ek8: compilation fix with randconfigs

   - usbtv: a trivial new USB ID addition

   - dibusb-common: don't do DMA on stack on firmware load

   - imx274: Fix error handling, add MAINTAINERS entry

   - sir_ir: detect presence of port"

* tag 'media/v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (50 commits)
  media: imx274: Fix error handling, add MAINTAINERS entry
  media: v4l: async: use the v4l2_dev from the root notifier when matching sub-devices
  media: v4l2-fwnode: Check subdev count after checking port
  media: et8ek8: select V4L2_FWNODE
  media: ov13858: Select V4L2_FWNODE
  media: rc: partial revert of "media: rc: per-protocol repeat period"
  media: dvb: i2c transfers over usb cannot be done from stack
  media: dvb-frontends: complete kernel-doc markups
  media: docs: add documentation for frontend attach info
  media: dvb_frontends: fix kernel-doc macros
  media: drivers: remove "/**" from non-kernel-doc comments
  media: lm3560: add a missing kernel-doc parameter
  media: rcar_jpu: fix two kernel-doc markups
  media: vsp1: add a missing kernel-doc parameter
  media: soc_camera: fix a kernel-doc markup
  media: mt2063: fix some kernel-doc warnings
  media: radio-wl1273: fix a parameter name at kernel-doc macro
  media: s3c-camif: add missing description at s3c_camif_find_format()
  media: mtk-vpu: add description for wdt fields at struct mtk_vpu
  media: vdec: fix some kernel-doc warnings
  ...

Pull drm fixes from Dave Airlie:
 "This pull is a bit larger than I'd like but a large bunch of it is
  license fixes, AMD wanted to fix the licenses for a bunch of files
  that were missing them,

 Otherwise a bunch of TTM regression fix since the hugepage support,
 some i915 and gvt fixes, a core connector free in a safe context fix,
 and one bridge fix"

* tag 'drm-fixes-for-v4.15-rc3' of git://people.freedesktop.org/~airlied/linux: (26 commits)
  drm/bridge: analogix dp: Fix runtime PM state in get_modes() callback
  Revert "drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk"
  drm/vc4: Fix false positive WARN() backtrace on refcount_inc() usage
  drm/i915: Call i915_gem_init_userptr() before taking struct_mutex
  drm/exynos: remove unnecessary function declaration
  drm/exynos: remove unnecessary descrptions
  drm/exynos: gem: Drop NONCONTIG flag for buffers allocated without IOMMU
  drm/exynos: Fix dma-buf import
  drm/ttm: swap consecutive allocated pooled pages v4
  drm: safely free connectors from connector_iter
  drm/i915/gvt: set max priority for gvt context
  drm/i915/gvt: Don't mark vgpu context as inactive when preempted
  drm/i915/gvt: Limit read hw reg to active vgpu
  drm/i915/gvt: Export intel_gvt_render_mmio_to_ring_id()
  drm/i915/gvt: Emulate PCI expansion ROM base address register
  drm/ttm: swap consecutive allocated cached pages v3
  drm/ttm: roundup the shrink request to prevent skip huge pool
  drm/ttm: add page order support in ttm_pages_put
  drm/ttm: add set_pages_wb for handling page order more than zero
  drm/ttm: add page order in page pool
  ...

Pull md fixes from Shaohua Li:
 "Some MD fixes.

  The notable one is a raid5-cache deadlock bug with dm-raid, others are
  not significant"

* tag 'md/4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/raid1/10: add missed blk plug
  md: limit mdstat resync progress to max_sectors
  md/r5cache: move mddev_lock() out of r5c_journal_mode_set()
  md/raid5: correct degraded calculation in raid5_error

Merge tag 'devicetree-fixes-for-4.15-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull DeviceTree fixes from Rob Herring:
 "Another set of DT fixes:

   - Fixes from overlay code rework. A trifecta of fixes to the locking,
     an out of bounds access, and a memory leak in of_overlay_apply()

   - Clean-up at25 eeprom binding document

   - Remove leading '0x' in unit-addresses from binding docs"

* tag 'devicetree-fixes-for-4.15-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: overlay: Make node skipping in init_overlay_changeset() clearer
  of: overlay: Fix out-of-bounds write in init_overlay_changeset()
  of: overlay: Fix (un)locking in of_overlay_apply()
  of: overlay: Fix memory leak in of_overlay_apply() error path
  dt-bindings: eeprom: at25: Document device-specific compatible values
  dt-bindings: eeprom: at25: Grammar s/are can/can/
  dt-bindings: Remove leading 0x from bindings notation
  of: overlay: Remove else after goto
  of: Spelling s/changset/changeset/
  of: unittest: Remove bogus overlay mutex release from overlay_data_add()

Pull virtio bugfixes from Michael Tsirkin:
 "A couple of minor bugfixes"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_net: fix return value check in receive_mergeable()
  virtio_mmio: add cleanup for virtio_mmio_remove
  virtio_mmio: add cleanup for virtio_mmio_probe