Merge tag 'omap-for-v4.17/soc-pt2-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc

Pull "Two omap5 specific aux control module patches for v4.17" from Tony Lindgren:

On omap5 there is an aux control module that we are not handling
currently for clocks, so let's add support for it.

* tag 'omap-for-v4.17/soc-pt2-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP5: control: add support for control module wkup pad config
  ARM: omap2+: control: add support for auxiliary control module instances

Merge tag 'samsung-soc-4.17-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/soc

Pull "Samsung mach/soc changes for v4.17, part two" from Krzysztof Kozłowski:

1. Fix coupled CPU idle freeze on Exynos4210.
2. Simplify hot-path in coupled CPU idle.

* tag 'samsung-soc-4.17-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: EXYNOS: Simplify code in coupled CPU idle hot path
  ARM: EXYNOS: Fix coupled CPU idle freeze on Exynos4210

Merge tag 'renesas-soc-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

Pull "Renesas ARM Based SoC Updates for v4.17" from Simon Horman:

01d675f1 ARM: shmobile: rcar-gen2: Add watchdog support
58adf1ba ARM: shmobile: Add watchdog support

* SoC
  - Identify R-Car V3H (r8a77980) and M3N (r8a77965)

  - Enable R-Car Gen2 regulator quirk for Stout board with H3 (r8a7790) SoC

    Marek Vaust says "Regulator setup is suboptimal on H2 Stout too. The
    Stout newly has two DA9210 regulators, so the quirk is extended to
    handle another DA9210 at i2c address 0x70."

  - Add watchdog support

    This is the SoC portion of the following solution. It is not yet
    enabled in DT as it is not functional without clock dependencies
    in place.

    Fabrizio Castro says "this series has been around for some time as RFC,
    and it has collected useful comments from the community along the way.
    The solution proposed by this patch set works for most R-Car Gen2 and
    RZ/G1 devices, but not all of them. We now know that for some R-Car
    Gen2 early revisions there is no proper software fix. Anyway, no
    product has been built around early revisions, but development boards
    mounting early revisions (basically prototypes) are still out there.
    As a result, this series isn't enabling the internal watchdog on R-Car
    Gen2 boards, developers may enable it in board specific device trees if
    needed.  This series has been tested by me on the iwg20d, iwg22d,
    Lager, Alt, and Koelsch boards.

   The problem
   ===========
   To deal with SMP on R-Car Gen2 and RZ/G1, we install a reset vector to
   ICRAM1 and we program the [S]BAR registers so that when we turn ON the
   non-boot CPUs they are redirected to the reset vector installed by Linux
   in ICRAM1, and eventually they continue the execution to RAM, where the
   SMP bring-up code will take care of the rest.  The content of the [S]BAR
   registers survives a watchdog triggered reset, and as such after the
   watchdog fires the boot core will try and execute the SMP bring-up code
   instead of jumping to the bootrom code.

   The fix
   =======
   The main strategy for the solution is to let the reset vector decide if
   it needs to jump to shmobile_boot_fn or to the bootrom code.  In a
   watchdog triggered reset scenario, since the [S]BAR registers keep their
   values, the boot CPU will jump into the newly designed reset vector, the
   assembly routine will eventually test WOVF (a bit in register RWTCSRA
   that indicates if the watchdog counter has overflown, the value of this
   bit gets retained in this scenario), and jump to the bootrom code which
   will in turn load up the bootloader, etc.  When bringing up SMP or using
   CPU hotplug, the reset vector will jump to shmobile_boot_fn instead."

* R-Car Rst
  - Add support for R-Car V3H (r8a77980) and V3H (r8a77980)

* R-Car SYSC
  - Mark rcar_sysc_matches[] __initconst

   Geert Uytterhoeven says "This frees another 1764 bytes
   (arm32/shmobile_defconfig) or 1000 bytes (arm64/renesas_defconfig) of
   memory after kernel init."

  - Fix power area parents

    Sergei Shtylyov says "According to the figure 9.2(b) of the R-Car
    Series, 3rd Generation User’s Manual: Hardware Rev. 0.80 the A2IRn and
    A2SCn power areas in R8A77970 have the A3IR area as a parent, thus the
    SYSC driver has those parents wrong.."

  - Add support for R-Car V3H (r8a77980) and V3H (r8a77980)

* tag 'renesas-soc-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: rcar-gen2: Add watchdog support
  ARM: shmobile: Add watchdog support
  ARM: shmobile: rcar-gen2: Fix error check in regulator quirk
  soc: renesas: rcar-rst: Add support for R-Car M3-N
  ARM: shmobile: stout: enable R-Car Gen2 regulator quirk
  soc: renesas: rcar-sysc: Add R-Car M3-N support
  soc: renesas: Identify R-Car M3-N
  soc: renesas: rcar-sysc: add R8A77980 support
  dt-bindings: power: add R8A77980 SYSC power domain definitions
  soc: renesas: r8a77970-sysc: fix power area parents
  soc: renesas: rcar-rst: Enable watchdog as reset trigger for Gen2
  soc: renesas: rcar-rst: add R8A77980 support
  soc: renesas: identify R-Car V3H
  soc: renesas: rcar-sysc: Mark rcar_sysc_matches[] __initconst

Merge tag 'sunxi-core-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/soc

Pull "Allwinner core changes for 4.17" from Maxime Ripard:

Here is our bunch of changes for mach-sunxi for this release cycle. This is
basically only about bringing the SMP support to the A80, which has a bug
in hardware and cannot use PSCI like the other SoCs we have.

* tag 'sunxi-core-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: sunxi: mc-smp: Split out SoC-specific device node lookup sequence
  ARM: sunxi: mc-smp: Use DT enable-method for sun9i A80 SMP
  ARM: sunxi: mc-smp: Fix "lookback" typo
  ARM: sun9i: smp: Support cpu0 hotplug
  dt-bindings: ARM: sunxi: Document A80 SoC secure SRAM usage by SMP hotplug
  ARM: sun9i: smp: Support CPU/cluster power down and hotplugging for cpu1~7
  ARM: sun9i: Support SMP bring-up on A80

Enable FlexCAN support as module by default. FlexCAN can be found
on various NXP designs such as the i.MX and Vybrid SoC family.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Enable the i.MX thermal driver required for i.MX SoC family.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This allows to successfully boot Colibri iMX7 which is using
the Ricoh RN5T567 PMIC.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Enable drivers to support NXP graphics IPs such as:
- Etnaviv (e.g. i.MX6)
- DCU (e.g. Vybrid LS1021A)
- mxsfb (e.g. i.MX6UL/ULL/7)
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add GPMI NAND controller support as required by some NXP i.MX6/7
based boards.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Enable on-chip OTP NVMEM support for NXP i.MX and VF610 SoCs.
Since OTP values might be required by drivers required during
boot, make sure the driver is built-in (e.g. i.MX thermal
driver).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

PMIC often require the I2C bus, and the PMIC regulators might be
necessary to power on eMMC/SD-card or other supplies required
for successful boot. Make sure I2C driver for i.MX devices is
built-in.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Enable the thermal monitor driver and the AVE ethernet driver
implemented on UniPhier SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'stratix10_defconfig_for_v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/soc

Pull "ARM64: stratix10: defconfig updates for 4.17" from Dinh Nguyen:

-enables STMMAC_ETH controller that is present on Stratix10

* tag 'stratix10_defconfig_for_v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  arm64: defconfig: enable stmmac ethernet to defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'omap-for-v4.17/defconfig-pt2-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc

Pull "Second set of defconfig changes for omap variants for v4.17" from Tony Lindgren:

This series enables more devices working on droid4 to make it easier
for people and distros to use out of the box.

* tag 'omap-for-v4.17/defconfig-pt2-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: multi_v7_defconfig: Enable CPCAP related options mostly as loadable modules
  ARM: omap2plus_defconfig: Add UINPUT
  ARM: omap2plus_defconfig: Enable MDM6600 USB PHY
  ARM: omap2plus_defconfig: Add AUDIO_GRAPH_CARD
  ARM: omap2plus_defconfig: Enable PWM_VIBRA

Merge tag 'qcom-arm64-defconfig-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/soc

Pull "Qualcomm ARM64 Based defconfig Updates for v4.17" from Andy Gross:

* Enable cpufreq governors, QCOM TSENS, and QCOM APCS driver

* tag 'qcom-arm64-defconfig-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  arm64: defconfig: enable more cpufreq governors
  arm64: defconfig: enable thermal sensor on QCOM platforms
  arm64: defconfig: Enable the APCS IPC driver on Qualcomm platforms
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'armsoc-versatile-drm-defconfig' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/soc

Pull "defconfig changes for Versatile DRM" from Linus Walleij:

This augments the RealView and Versatile defconfig to use the PL111
DRM driver rather than the old fbdev driver.

* tag 'armsoc-versatile-drm-defconfig' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
  ARM: defconfig: Configure Versatile boards to use PL111 DRM
  ARM: defconfig: Update Versatile defconfig
  ARM: defconfig: Switch RealView boards to use P111 DRM
  ARM: defconfig: Update RealView defconfig

Merge tag 'amlogic-defconfig' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/soc

Pull "Amlogic defconfig fixes for v4.17" from Kevin Hilman

* tag 'amlogic-defconfig' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  arm64: defconfig: enable MESON EFUSE

Merge tag 'omap-for-v4.17/defconfig-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc

Pull "Defconfig updates for omap variants for v4.17 merge window"
from Tony Lindgren:

We need to enable MMC_SDHCI option in both omap2plus_defconfig and
multi_v7_defconfig so systems are able to mount root when the dts files
get updated for sdhci.

Then let's update omap2plus_defconfig so we can patch it easier. And as
Arnd noticed earlier, just running make savedefconfig will accidentally
drop few Kconfig options. This is happening because some options are no
longer available as loadable modules like LIRC. Or new dependencies have
been added such as SND_OSSEMUL for selecting SOUND_OSS_CORE.

So we first move the unchanged options around to their make savedefconfig
suggested place, then update the options to prevent make savedefconfig
dropping some options accidentally, and then finally drop the unused
options.

And after that we enable options DRM_OMAP and 8250_OMAP. These both have
been around for years now. And we do have 8250_OMAP warn about console
being redirected with SERIAL_8250_OMAP_TTYO_FIXUP option that is enabled
by default. Some users may need to update their inittab to use ttyS*
instead of ttyO* though. If this turns out to be a problem, we may want
to introduce a separate compatible for 8250-omap. But I think we're good
to go with the SERIAL_8250_OMAP_TTYO_FIXUP warning now. Let's not update
multi_v7_defconfig yet though and first see how 8250_OMAP change plays
out.

We also enable few new options for PM on am335x and am437x, and CEC in
omap2plus_defconfig. Naturally similar options can be later on added to
multi_v7_defconfig, but in this series we only enable OTG, MUSB and the
related PHYs in multi_v7_defconfig to make it more usable for distros.

* tag 'omap-for-v4.17/defconfig-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: multi_v7_defconfig: Enable USB gadget configfs as loadable module
  ARM: multi_v7_defconfig: Enable various USB PHYs found on omap variants
  ARM: multi_v7_defconfig: Enable OTG and MUSB as loadable modules
  ARM: omap2plus_defconfig: Enable 8250_OMAP
  ARM: omap2plus_defconfig: Switch to use omapdrm by default
  ARM: omap2plus_defconfig: Enable CEC
  ARM: omap2plus_defconfig: Enable am335x and am437x PM options
  ARM: omap2plus_defconfig: Drop unneeded options
  ARM: omap2plus_defconfig: Add SND_OSSEMUL
  ARM: omap2plus_defconfig: Update LIRC options
  ARM: omap2plus_defconfig: Select MFD_TI_LMU
  ARM: omap2plus_defconfig: Add SERIAL_DEV for bluetooth
  ARM: omap2plus_defconfig: Update for moved options
  ARM: omap2plus_defconfig: Enable CONFIG_MMC_SDHCI_OMAP
  ARM: multi_v7_defconfig: Enable CONFIG_MMC_SDHCI_OMAP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-defconfig-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

Pull "Renesas ARM Based SoC Defconfig Updates for v4.17" from Simon Horman:

Updates to shmobile defconfig:

* Redresh defconfig to ease future maintenence overhead

* Disable CONFIG_EMBEDDED

  Geert Uytterhoeven says "CONFIG_EXPERT exposes too many config options
  that do not matter for development.  E.g. it prohibits using the default
  values for the various SH_SCI options.  However, CONFIG_EMBEDDED selects
  CONFIG_EXPERT, so it cannot be disabled.

  Hence disable CONFIG_EMBEDDED, and compensate for the loss of
  CONFIG_DEBUG_KERNEL by enabling the latter.

  Actual impact, all harmless:
    - CONFIG_NAMESPACES=y (plus a few related CONFIG_*_NS options),
    - CONFIG_SYSCTL_SYSCALL=n,
    - CONFIG_SERIAL_SH_SCI_NR_UARTS changed from 20 to 18,
    - Some HID support became enabled,
    - CONFIG_DEBUG_MEMORY_INIT=y,"

* Enable RZA1 pin controller

  This allows the Genmai board with RZ/A1 (r7s72100) SoC to once
  again boot using the shmobile defconfig.

* tag 'renesas-defconfig-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: defconfig: Disable CONFIG_EMBEDDED
  ARM: shmobile: defconfig: Refresh
  ARM: shmobile: Enable RZA1 pin controller

Merge tag 'renesas-arm64-defconfig-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

Pull "Renesas ARM64 Based SoC Defconfig Updates for v4.17" from Simon Horman:

Enable the following to allow them to be more widely exercised:
* Newly added R8A77965 and R8A77980 SoCs
* PWM and USB as used on R-Car Gen3 SoCs

* tag 'renesas-arm64-defconfig-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  arm64: defconfig: enable R8A77965 SoC
  arm64: defconfig: Enable PWM and USB for R-Car
  arm64: defconfig: enable R8A77980 SoC

Merge tag 'tegra-for-4.17-arm64-defconfig' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc

Pull "arm64: Default configuration updates for v4.17-rc1" from Thierry Reding:

Enable the BPMP thermal and CPU frequency drivers as well as make sure
that the Tegra SMMU is enabled by default because there's no fun without
it. Also enable initial Tegra194 support.

* tag 'tegra-for-4.17-arm64-defconfig' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  arm64: defconfig: Enable the Tegra SMMU by default
  arm64: defconfig: Enable CONFIG_TEGRA_BPMP_THERMAL
  arm64: defconfig: Enable CONFIG_ARM_TEGRA186_CPUFREQ
  arm64: defconfig: Enable NVIDIA Tegra194 support

Merge tag 'imx-defconfig-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc

Pull "i.MX defconfig updates for 4.17" from Shawn Guo:

 - Re-sync defconfig files by running savedefconfig.
 - Enable generic fsl-asoc-card driver for imx_v4_v5_defconfig.
 - Enable MAG3110 magnetometer sensor driver, AC97 and WM8962 codec
   driver, DA9062/63 PMIC, RTC and Watchdog support for
   imx_v6_v7_defconfig.

* tag 'imx-defconfig-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: mxs_defconfig: Re-sync defconfig
  ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
  ARM: imx_v4_v5_defconfig: Re-sync defconfig
  ARM: imx_v6_v7_defconfig: Select CONFIG_SND_SOC_WM8962 explicitly
  ARM: imx_v6_v7_defconfig: Re-sync defconfig
  ARM: imx_v6_v7_defconfig: Enable Dialog Semiconductor DA9062 driver
  ARM: imx_v6_v7_defconfig: Enable AC97 codec support
  ARM: imx: Update imx_v6_v7_defconfig for mag3110 support
  ARM: imx_v6_v7_defconfig: enable OP-TEE
  ARM: imx_v6_v7_defconfig: select the CONFIG_CPUFREQ_DT

When selecting SOC_IMX6SLL but not SOC_IMX6SL, we get a link error:

arch/arm/mach-imx/mach-imx6sl.o: In function `imx6sl_init_late':
mach-imx6sl.c:(.init.text+0x14): undefined reference to `imx6sl_cpuidle_init'

This adds the missing line to the Makefile to also build the cpuidle
support that we need here.

Fixes: dee5dee2 ("ARM: imx: Add basic msl support for imx6sll")
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The cpuidle support calls cpu_suspend(), which is compiled conditionally,
and fails to link unless something selects CONFIG_ARM_CPU_SUSPEND.

arch/arm/mach-imx/cpuidle-imx6sx.o: In function `imx6sx_enter_wait':
cpuidle-imx6sx.c:(.text+0x6c): undefined reference to `cpu_suspend'

This adds an explicit select statement here.
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Re-sync the defconfig by doing:

make savedefconfig
cp defconfig arch/arm/configs/mxs_defconfig

So keep it in sync to help further changes in defconfig.

The explanation for removing the Kconfig symbols:

CONFIG_FHANDLE=y: verified that it is still selected
selected
CONFIG_DEVPTS_MULTIPLE_INSTANCES=y: does not exist anymore
CONFIG_NVMEM=y: verified that it is still selected
CONFIG_LOCKUP_DETECTOR=y: need to select CONFIG_SOFTLOCKUP_DETECTOR now
CONFIG_TIMER_STATS=y: does not exist anymore

Boot tested on a imx28evk.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

fsl-asoc-card machine driver also supports sgtl5000, so use it favor
of the imx-sgtl5000 machine driver, which will be probably be removed
in the future.

Tested on a imx25-pdk board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Re-sync the defconfig by doing:

make savedefconfig
cp defconfig arch/arm/configs/imx_v4_v5_defconfig

So keep it in sync to help further changes in defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch enables the CONFIG_STMMAC_ETH to the default arm64 defconfig:

-CONFIG_STMMAC_ETH=m
+CONFIG_STMMAC_ETH=y
+CONFIG_DWMAC_IPQ806X=m
+CONFIG_DWMAC_MESON=m
+CONFIG_DWMAC_ROCKCHIP=m
+CONFIG_DWMAC_SUNXI=m
+CONFIG_DWMAC_SUN8I=m

The STMMAC ethernet controller is on the Stratix10 platform, and thus needs
driver to be in the kernel image for NFS to work.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

exynos_enter_aftr() is called by coupled CPU idle code every time CPU
enters idle state, what can be considered as a hot path. Replace
of_machine_is_compatible() call with a simple SoC revision check.

of_machine_is_compatible() function performs a dozen of string comparisons
during the full device tree walk, while soc_is_exynos4412() is a simple
integer check on SoC revision variable.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

Since commit 04c8b0f8 ("irqchip/gic: Make locking a BL_SWITCHER only
feature") coupled CPU idle freezes from time to time on Exynos4210. Later
commit 313c8c16 ("PM / CPU: replace raw_notifier with atomic_notifier")
changed the context in which the CPU idle code is executed, what results
in fully reproducible freeze all the time. However, almost the same coupled
CPU idle code works fine on Exynos3250 regardless of the changes made in
the mentioned commits.

It turned out that the IPI call used on Exynos4210 is conflicting with the
change done in the first mentioned commit in GIC. Fix this by using the
same code path as for Exynos3250, instead of the IPI call for
synchronization with second CPU core, call dsb_sev() directly.

Tested on Exynos4210-based Trats and Origen boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: <stable@vger.kernel.org> # v4.13+
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

Match the new compatible string in the control module driver. The base
infra maps the required syscon ranges and clock registers if available.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Control module can have multiple instances in a system, each with separate
address space and features. Add base support for these auxiliary instances,
with support for syscon and clock mappings under them.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We need the CPCAP MFD and regulator built-in for UART console to work,
the rest can be loadable modules. Note that users probably want to also
enable serial 8250_OMAP that is not yet enabled by default.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This can be used for keyboard fn keys with funkeymonkey.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This allows droid 4 USB modem to work.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is needed for audio on droid 4.
Signed-off-by: Tony Lindgren <tony@atomide.com>

We can use PWM_VIBRA on many phones like droid 4.
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DRM driver is now finalized for the Versatile board family,
so switch the defconfig to use this driver instead of the old
fbdev driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This updates the Versatile defconfig to the latest savedefconfig
results reflecting changes in Kconfig. We add in the Flash memory
support that has been available upstream for a while now.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The DRM driver is now finalized for the RealView board family,
so switch the defconfig to use this driver instead of the old
fbdev driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>