There is settling time for each rails when it is switched to
ON. Implementing enable time for returning proper settling time
of regulator rails when it is enabled.
Filling the on-time for each rail as per tps65910/tps65911
datasheets.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use DIV_ROUND_UP macro for better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The address of ctrl and sel registers can be calculated by simple equations.
This patch simplifies the implementation in tps65912_get_ctrl_register and
implements tps65912_get_sel_register to replace tps65912_get_dcdc_sel_register
and tps65912_get_ldo_sel_register.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We actually clear LDO_ST_ON_BIT for standby mode in tps65910_set_mode.
Fix the logic in tps65910_get_mode.

Supply state (EEPROM bits):
ST[1:0] = 00 : Off
ST[1:0] = 01 : On high power (ACTIVE)
ST[1:0] = 10 : Off
ST[1:0] = 11 : On low power (SLEEP)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Most callback functions implementation for tps65217_pmic_ldo234_ops and
tps65217_pmic_dcdc_ops are the same except the rid range checking.

This patch uses tps65217_pmic_ops for all DCDCx, LDO2, LDO3, and LDO4.
And rework tps65217_pmic_set_voltage to make it can be called for
DCDCx, LDO2, LDO3, and LDO4.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

DIV_ROUND_CLOSEST performs the computation (x + d/2)/d with better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Then we can use the regulator id as array index to access the array.
This change makes the code simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This function finds the smallest voltage that falls within the specified range,
and then returns the selector. This rename makes the intention more clear.

Also remove unneeded local variables min_vol and max_vol in s5m8767_set_voltage
and s5m8767_set_voltage_buck.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This change improves readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

In the s5m8767_set_voltage_time_sel function, divisor unit is wrong.
ramp_delay is usec unit. So 1000 should be multiplied.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Keep the rails OFF in sleep mode only when the rails are
controlled by external sleep control.
The devices tps65910 and tps65911, both has the sleep input.
The tps65911's sleep input is not same as tps65910's EN3 and hence
taking care of SLEEP input as separate external sleep control input.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Call tps65912_list_voltage_dcdc instead of duplicating the same code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use DIV_ROUND_UP macro for better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This looks like a mistakenly committed debug logging.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use DIV_ROUND_UP macro for better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use DIV_ROUND_UP macro for better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

If used as a dummy voltage provider the fixed regulator should
not set n_voltages to make the core accept the device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The reason we add *pdev in struct aat2870_regulator is to use it
to get a pointer to struct aat2870_data.
Save a pointer to struct aat2870_data instead of pdev in struct
aat2870_regulator, this change makes the intention more clear.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use rdev_get_id() directly.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use rdev_get_id() directly.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Current code has off-by-one n_voltage settings for AUTO/DOWN*/LDO* regulators.

Take ldo1 as example:
n_voltage should be (3.6 - 0.9) / 0.1 + 1 = 28

Table 76. LDO1OUT - LDO1 output voltage select register (address 2Dh) bit description[1]
Bit Symbol Access Description
4:0 ldo1_out R/W VO(prog) = 0.9 + ldo1_out × 0.1 V (max 3.6V); e.g.
00000 : 0.9 V
00001 : 1.0 V
11000 : 3.3 V
11011 : 3.6 V
11111 : 3.6 V

The n_voltage settings for HCLDO and MEMLDO are also wrong.
n_voltage for HCLDO and MEMLDO should be (3.6 - 0.9) / 0.1 + 1 = 28

Table 88. HCLDOOUT - HCLDO output voltage select register (addr. 39h) bit description[1]
Bit Symbol Access Description
4:0 hcldo_out R/W VO(prog) = 0.9 + hcldo_out × 0.1 V (max 3.6 V); e.g.
00000 : 0.9 V
00001 : 1.0 V
11011 : 3.6 V
11111 : 3.6 V

Table 62. MEMLDOOUT - MEMLDO o/p voltage select reg. (address 26h) bit description[1]
Bit Symbol Access Description
4:0 memldo_out R/W VO(prog) = 0.9 + memldo_out × 0.1 V; e.g.
00000: 0.9 V
00001: 1.0 V
11000 : 3.3 V
11011 : 3.6 V
11111 : 3.6 V
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch includes below fixes:
1. The mask variable is not used at all here, remove it.
2. We already have the new_sel and old_sel, simply returns the delay by:
  DIV_ROUND_UP(desc->step * (new_sel - old_sel), s5m8767->ramp_delay);
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

the platform data pointer is used without checking it. Bail out
in the driver instead of crashing the kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This change is required to make ab8500_regulator_get_voltage_sel work.
The regulator core will call set_voltage_time_sel only when get_voltage_sel is
implemented.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Sort Kconfig entries by company name/driver in alphabetical order.
Sort Makefile entries by alphabetical order.

In order to group all the Kconfig entries by company name,
this patch also adds company name to some Kconfig entries.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix the module desciption and also update Kconfig to include supporting
tps65911 chip.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The VIO regulator register specify the voltage configuration
on bit3:2 of its register. And hence only these bits should
be modified when setting voltage and used when reading voltage
from register setting.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The variable 'selector' is a 'unsigned int', so it can never be less than zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This looks like a merge mistake.  Calling regmap_update_bits once is enough.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>