Merge tag 'renesas-dt3-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Merge "Third Round of Renesas ARM Based SoC DT Updates for v3.16" from Simon
Horman:

r8a7791 (R-Car M2), r8a7779 (R-Car H1), r8a7778 (R-Car M1),
r8a7740 (R-Mobile A1) and r8a73a4 (R-Mobile APE6) SoCs
* Move interrupt-parent property to root node

r8a7791 (R-Car M2) and r8a7790 (R-Car H2) SoCs
* Add GPIO clocks

r8a7791 (R-Car M2) based Henninger board
* Add MSIOF0, QSPI and SDHI0/2 support
* Specify EXTAL frequency

r8a7779 (R-Car H1) based Marzen board
* Set SMSC lan to use irq-push-pull

r8a7740 (R-Mobile A1) SoC
* Remove duplicate interrupt-parent property

r8a7740 (R-Mobile A1) based Armadillo800 EVA board
* Add Ethernet support

* tag 'renesas-dt3-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7740 dtsi: Remove duplicate interrupt-parent property
  ARM: shmobile: marzen-reference: Set SMSC lan to use irq-push-pull
  ARM: shmobile: r8a7791 dtsi: Add GPIO clocks
  ARM: shmobile: r8a7790 dtsi: Add GPIO clocks
  ARM: shmobile: dts: Move interrupt-parent property to root node
  ARM: shmobile: armadillo-reference dts: Add Ethernet support
  ARM: shmobile: r8a7740 dtsi: Add Ethernet support
  ARM: shmobile: henninger: add MSIOF0 DT support
  ARM: shmobile: henninger: add QSPI DT support
  ARM: shmobile: henninger: add SDHI0/2 DT support
  ARM: shmobile: henninger: specify EXTAL frequency
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge "at91: DT for 3.16 #2" from Nicolas Ferre:

3.16: second DT series:
- at91sam9rl and at91sam9261 fixes about PLL ranges
- at91sam9261 more comprehensive support for SSC
- sama5d3 Xplained: addition of pull-ups, PWM and PMIC (regulator)

* tag 'at91-dt2' of git://github.com/at91linux/linux-at91:
  ARM: at91/dt: at91-sama5d3_xplained: add the regulator device node
  ARM: at91: add 2 PWM outputs to SAMA5D3 Xplained
  ARM: at91: add PWM pinctrl to SAMA5D3
  ARM: at91: add pull-up to i2c[02] on SAMA5D3 Xplained
  ARM: at91/dt: sam9rl: Fix PLL output range and mck divisors
  ARM: at91/dt: sam9261: Add ssc2, SSC clocks and pcks
  ARM: at91/dt: sam9261: Fix PLL output ranges and other clocks divisors
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt

Merge "ARM: Keystone DTS updates for 3.16" from Santosh Shilimkar:

Keystone DTS updates for 3.16

- Few of address cell warning fixes.
- Add Lamarr and Edision EVM NOR flash and NAND devices.
- Update dts to make use of dma-ranges and dma-coherent properties.

* tag 'keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: dts: keystone-evm: add spi nor flash support
  ARM: dts: k2l-evm: add AEMIF/NAND device entry
  ARM: dts: k2e-evm: add AEMIF/NAND device entry
  ARM: dts: keystone: Update USB node for dma properties
  ARM: dts: keystone: Use dma-ranges property
  ARM: dts: keystone: add cell's information to spi nodes
  ARM: dts: keystone: move i2c0 device node from SoC to board files
  ARM: dts: keystone: add cell's information to i2c nodes
  ARM: dts: keystone: drop address and size cells from GIC node
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'v3.16-rockchip-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Merge "ARM: rockchip: devicetree changes for v3.16" from Heiko Stübner:

Addition of missing board compatible names and their vendor-prefixes
as well as the dts portions of the pinctrl rework.

* tag 'v3.16-rockchip-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: convert pinctrl nodes to new bindings
  ARM: dts: rockchip: add root compatible properties
  of: add mundoreader and radxa vendor prefixes
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge "ARM: mvebu: DT changes for v3.16" from Jason Cooper:

mvebu DT changes for v3.16

 - kirkwood
    - rework nsa3x0 board to add nsa320
    - large cleanup to facilitate use in barebox
    - guruplug phy updates
    - audio updates for t5325

 - mvebu
    - use clocks vice clock-frequency for uart nodes

    - armada 375/380/385
       - add watchdog node
       - add coherency fabric
       - add smp support
       - add sdhci
       - add ahci
       - add thermal sensor

    - armada 370/XP
       - and pmsu

* tag 'mvebu-dt-3.16' of git://git.infradead.org/linux-mvebu: (35 commits)
  ARM: Kirkwood: t5325: Use simple card to instantiate audio
  ARM: Kirkwood: DT: Add missing #sound-dai-cells property
  ARM: Kirkwood: Add node for audio codec
  ARM: dts: kirkwood: set Guruplug phy-connection-type to rgmii-id
  ARM: dts: kirkwood: set Guruplug ethernet PHY compatible
  ARM: dts: kirkwood: set default pinctrl for I2C1 on 6282
  ARM: dts: kirkwood: set default pinctrl for I2C0
  ARM: dts: kirkwood: set default pinctrl for NAND
  ARM: dts: kirkwood: set default pinctrl for SPI0
  ARM: dts: kirkwood: set default pinctrl for UART0/1
  ARM: dts: kirkwood: set default pinctrl for GBE1
  ARM: dts: kirkwood: consolidate common pinctrl settings
  ARM: dts: kirkwood: add pinctrl node to common SoC include
  ARM: dts: kirkwood: rename pin-controller nodes
  ARM: dts: kirkwood: remove clock-frequency properties from UART nodes
  ARM: dts: kirkwood: add stdout-path property to all boards
  ARM: dts: kirkwood: add node labels
  ARM: mvebu: Enable the thermal sensor in Armada 380/385 SoC
  ARM: mvebu: Enable the thermal sensor in Armada 375 SoC
  ARM: mvebu: don't use clocks property in UART node for Netgear RN2120
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'socfpga-dt-updates-for-3.16_v3' of git://git.rocketboards.org/linux-socfpga-next into next/dt

Merge "dts: socfpga: general updates for the socfpga platform" from Dinh
Nguyen:

Mostly DTS additions to the SOCFPGA platform from Steffan Trumtrar, and a
couple of device tree documentation updates/typo fix.

This one does not the GPIO binding patch, as that is pending further
discussion. Also, v3 fixes a rebase artifact and compile tested.

* tag 'socfpga-dt-updates-for-3.16_v3' of git://git.rocketboards.org/linux-socfpga-next:
  ARM: socfpga: dts: Add div-reg to the main_pll clocks
  ARM: socfpga: dts: add reset-controller
  Documentation: dt: reset: move socfpga-reset
  Documentation: dt: socfpga: add reset-cells property
  ARM: socfpga: dts: Add DTS entries for USB
  ARM: socfpga: dts: Remove hard coded clock-frequency property
  ARM: socfpga: dts: add eeprom and rtc on i2c0
  ARM: socfpga: dts: convert to preprocessor includes
  ARM: socfpga: dts: add rtc on i2c0 to socrates
  ARM: socfpga: dts: add support for EBV SOCrates
  ARM: socfpga: dts: add can0+1
  ARM: socfpga: dts: add i2c busses
  ARM: socfpga: dts: add remaining interrupts for pdma
  ARM: socfpga: dts: fix pdma interrupt
Signed-off-by: Olof Johansson <olof@lixom.net>

Caused by interaction between commit
08ec67b5 ("ARM: shmobile: r8a7740 dtsi:
Add Ethernet support") and commit 9ff254ad
("ARM: shmobile: dts: Move interrupt-parent property to root node").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This change makes the DTS consistent with the platform data
that exists in board-marzen.c.

Empirically it does not appear to be necessary.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

There's no need to duplicate the interrupt-parent property in all DT
nodes as the kernel automatically walks parent nodes to find the
property. Specify it once in the root node only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

k2hk, k2e, k2l EVM board have the same Micron N25Q128A11
SPI NOR Flash installed on SPI0 bus.

The NOR Flash is splitted on two partistions:
partition@0
	label = "u-boot-spl";
	reg = <0x0 0x80000>;
partition@1
	label = "misc";
	reg = <0x80000 0xf80000>;

Hence, add SPI NOR Flash nodes to all k2hk, k2e, k2l EVM boards.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add PWM high output of channels 0 and 1 to PA20 PA22 pins.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

As there are no pull-up resistors on the board itself it can be useful to
use the SoC pad pull-up to be able to easily connect usual i2c devices.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Argument 3 (OUT) and 4 (ICPLL) of the atmel,pll-clk-output-ranges were missing.
Also, the at91sam9rl doesn't really have a by 3 divisor.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add ssc2 support, ssc2 pinctrl and clocks for the three SSCs.
Also add support for the programmable clocks.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Argument 3 (OUT) and 4 (ICPLL) of the atmel,pll-clk-output-ranges were missing.
Also, the at91sam9261 doesn't really have a by 3 divisor.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Henninger board dependent part of the MSIOF0 device node.
Add device node for Renesas R2A11302FT PMIC for which no bindings exist yet.

Based on the Koelsch MSIOF device tree patch by Geert Uytterhoeven.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Henninger board dependent part of the QSPI device node.
Add device nodes for Spansion S25FL512S SPI flash and MTD partitions on it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Henninger board dependent part of the SDHI0/2 device nodes along with
the necessary voltage regulators (note that the Vcc regulators are dummy -- they
are required but don't actually exist on the board). Also, GPIOs have to be used
for the CD and WP signals due to the SDHI driver constraints...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Introduce the grf syscon and convert the pinctrl drivers for rk3066 and rk3188
to use it, instead of mapping the grf registers themselfs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

Add the missing 'compatible' property to device tree root node of

 - rk3066a-bqcurie2.dts
 - rk3188-radxarock.dts

and document the new values.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add new vendor prefixes for:

    * Mundo Reader S.L., a company that produces tablets and e-readers
    * Radxa, manufacturer of ARM boards
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add AEMIF/NAND device entry.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Add AEMIF/NAND device entry.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Keystone supports dma-coherent on USB master and also needs
dma-ranges to specify the hardware alias memory range in which DMA
can be operational.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

The dma-ranges property has to be specified per bus and has format:
 < DMA addr > - Base DMA address for Bus (Bus format 32-bits)
 < CPU addr > - Corresponding base CPU address (CPU format 64-bits)
 < DMA range size > - Size of supported DMA range

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

SPI nodes should always have #address-cells and #size-cells defined,
otherwise warnings will be produced in case of adding any child
nodes to the SPI bus in DT:
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/spi@21000400/n25q128a11@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/spi@21000400/n25q128a11@0

Hence, ensure that all SPIx nodes have #address-cells and #size-cells
properties defined.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

I2C devices are not the part of Keystone SoC and have to be
defined in board DTS files.
Hence, move i2c0 EEPROM device node from Keystone SoC to
k2hk, k2e, k2l EVM files as they all have similar EEPROM SoCs
installed.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

I2C nodes should always have #address-cells and #size-cells defined,
otherwise warnings will be produced in case of adding child
nodes to the I2C bus in DT:
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/i2c@2530800/pca@20
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/i2c@2530800/pca@20

Hence, ensure that all i2cX nodes have #address-cells and #size-cells
properties defined.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.

address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

The mpu_clk, main_clk, and dbg_base_clk outputs from the main PLL go through a
pre-divider. Update socfpga.dtsi to represent those dividers for these
clocks.

Re-use the "div-reg" property that was used for the socfpga-gate-clock as this
is the same thing. Also update the documentation.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>

Add the necessary #reset-cells property to the rst-mgr node and
provide a header-file with all possible resets specified.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>

Instead of having the documentation for the socfpga-reset controller in a
vendor specific directory, move it to the reset folder to all the other
reset drivers.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>

To be able to use the reset-controller framework, the property
        #reset-cells
is mandatory.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>

Update all the SOCFPGA DTS files with USB entries.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>