- 03 Aug, 2018 3 commits
-
-
Christoph Hellwig authored
kernel/dma/Kconfig already defines NEED_DMA_MAP_STATE, just select it from CONFIG_PPC using the same condition as an if guard. Signed-off-by:
Christoph Hellwig <hch@lst.de> [mpe: Move it under PPC] Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au>
-
Guenter Roeck authored
An arbitrary error in ppc4xx_msi_probe() quite likely results in a crash similar to the following, seen after dma_alloc_coherent() returned an error. Unable to handle kernel paging request for data at address 0x00000000 Faulting instruction address: 0xc001bff0 Oops: Kernel access of bad area, sig: 11 [#1] BE Canyonlands Modules linked in: CPU: 0 PID: 1 Comm: swapper Tainted: G W 4.18.0-rc6-00010-gff33d1030a6c #1 NIP: c001bff0 LR: c001c418 CTR: c01faa7c REGS: cf82db40 TRAP: 0300 Tainted: G W (4.18.0-rc6-00010-gff33d1030a6c) MSR: 00029000 <CE,EE,ME> CR: 28002024 XER: 00000000 DEAR: 00000000 ESR: 00000000 GPR00: c001c418 cf82dbf0 cf828000 cf8de400 00000000 00000000 000000c4 000000c4 GPR08: c0481ea4 00000000 00000000 000000c4 22002024 00000000 c00025e8 00000000 GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 c0492380 0000004a GPR24: 00029000 0000000c 00000000 cf8de410 c0494d60 c0494d60 cf8bebc0 00000001 NIP [c001bff0] ppc4xx_of_msi_remove+0x48/0xa0 LR [c001c418] ppc4xx_msi_probe+0x294/0x3b8 Call Trace: [cf82dbf0] [00029000] 0x29000 (unreliable) [cf82dc10] [c001c418] ppc4xx_msi_probe+0x294/0x3b8 [cf82dc70] [c0209fbc] platform_drv_probe+0x40/0x9c [cf82dc90] [c0208240] driver_probe_device+0x2a8/0x350 [cf82dcc0] [c0206204] bus_for_each_drv+0x60/0xac [cf82dcf0] [c0207e88] __device_attach+0xe8/0x160 [cf82dd20] [c02071e0] bus_probe_device+0xa0/0xbc [cf82dd40] [c02050c8] device_add+0x404/0x5c4 [cf82dd90] [c0288978] of_platform_device_create_pdata+0x88/0xd8 [cf82ddb0] [c0288b70] of_platform_bus_create+0x134/0x220 [cf82de10] [c0288bcc] of_platform_bus_create+0x190/0x220 [cf82de70] [c0288cf4] of_platform_bus_probe+0x98/0xec [cf82de90] [c0449650] __machine_initcall_canyonlands_ppc460ex_device_probe+0x38/0x54 [cf82dea0] [c0002404] do_one_initcall+0x40/0x188 [cf82df00] [c043daec] kernel_init_freeable+0x130/0x1d0 [cf82df30] [c0002600] kernel_init+0x18/0x104 [cf82df40] [c000c23c] ret_from_kernel_thread+0x14/0x1c Instruction dump: 90010024 813d0024 2f890000 83c30058 41bd0014 48000038 813d0024 7f89f800 409d002c 813e000c 57ea103a 3bff0001 <7c69502e> 2f830000 419effe0 4803b26d ---[ end trace 8cf551077ecfc42a ]--- Fix it up. Specifically, - Return valid error codes from ppc4xx_setup_pcieh_hw(), have it clean up after itself, and only access hardware after all possible error conditions have been handled. - Use devm_kzalloc() instead of kzalloc() in ppc4xx_msi_probe() Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Reviewed-by:
-
Nicholas Piggin authored
Commit 9c7b185a ("powernv/cpuidle: Parse dt idle properties into global structure") parses dt idle states into structs, but never marks them valid. This results in all idle states being lost. Fixes: 9c7b185a ("powernv/cpuidle: Parse dt idle properties into global structure") Signed-off-by:
Nicholas Piggin <npiggin@gmail.com> Acked-by:
Akshay Adiga <akshay.adiga@linux.vnet.ibm.com> Signed-off-by:
-
- 31 Jul, 2018 16 commits
-
-
Sam Bobroff authored
EEH recovery currently fails on pSeries for some IOV capable PCI devices, if CONFIG_PCI_IOV is on and the hypervisor doesn't provide certain device tree properties for the device. (Found on an IOV capable device using the ipr driver.) Recovery fails in pci_enable_resources() at the check on r->parent, because r->flags is set and r->parent is not. This state is due to sriov_init() setting the start, end and flags members of the IOV BARs but the parent not being set later in pseries_pci_fixup_iov_resources(), because the "ibm,open-sriov-vf-bar-info" property is missing. Correct this by zeroing the resource flags for IOV BARs when they can't be configured (this is the same method used by sriov_init() and __pci_read_base()). VFs cleared this way can't be enabled later, because that requires another device tree property, "ibm,number-of-configurable-vfs" as well as support for the RTAS function "ibm_map_pes". These are all part of hypervisor support for IOV and it seems unlikely that a hypervisor would ever partially, but not fully, support it. (None are currently provided by QEMU/KVM.) Signed-off-by:
Sam Bobroff <sbobroff@linux.ibm.com> Reviewed-by:
Bryant G. Ly <bryantly@linux.ibm.com> Signed-off-by:
-
Shilpasri G Bhat authored
OPAL firmware provides the facility for some groups of sensors to be enabled/disabled at runtime to give the user the option of using the system resources for collecting these sensors or not. For example, on POWER9 systems, the On Chip Controller (OCC) gathers various system and chip level sensors and maintains their values in main memory. This patch provides support for enabling/disabling the sensor groups like power, temperature, current and voltage. Signed-off-by:
Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com> [stewart@linux.vnet.ibm.com: Commit message] Acked-by:
-
Shilpasri G Bhat authored
Adds support to enable/disable a sensor group at runtime. This can be used to select the sensor groups that needs to be copied to main memory by OCC. Sensor groups like power, temperature, current, voltage, frequency, utilization can be enabled/disabled at runtime. Signed-off-by:
-
Akshay Adiga authored
Export pnv_idle_states and nr_pnv_idle_states so that its accessible to cpuidle driver. Use properties from pnv_idle_states structure for powernv cpuidle_init. Signed-off-by:
Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by:
-
Akshay Adiga authored
Device-tree parsing happens twice, once while deciding idle state to be used for hotplug and once during cpuidle init. Hence, parsing the device tree and caching it will reduce code duplication. Parsing code has been moved to pnv_parse_cpuidle_dt() from pnv_probe_idle_states(). In addition to the properties in the device tree the number of available states is also required. Signed-off-by:
-
Finn Thain authored
Some of the event counters are overloaded which makes it very difficult to interpret their values. Counter 0 is supposed to report CB1 interrupts but it can also count PMU_INT_WAITING_CHARGER events. Counter 1 is supposed to report GPIO interrupts but it can also count other events (depending upon the value of the PMU_INT_ADB bit). Disambiguate these statistics with dedicated counters for GPIO and CB1 interrupts. Comments in the MkLinux source code say that the type 0 and type 1 interrupts are model-specific. Label them as "unknown". This change to the contents of /proc/pmu/interrupts is by necessity visible in userland. However, packages which interact with the PMU (that is, pbbuttonsd, pmac-utils and pmud) don't open this file. AFAIK, user software has no need to poll these counters. Tested-by:
Stan Johnson <userm57@yahoo.com> Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
-
Finn Thain authored
Replace an open-coded ffs() with the function call. Simplify an if-else cascade using a switch statement. Correct a typo and an indentation issue. Tested-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Finn Thain authored
Now that the PowerMac via-pmu driver supports m68k PowerBooks, switch over to that driver and remove the via-pmu68k driver. Tested-by:
-
Finn Thain authored
Don't load the via-pmu68k driver on early PowerBooks. The M50753 PMU device found in those models was never supported by this driver. Attempting to load the driver usually causes a boot hang. Signed-off-by:
Michael Schmitz <schmitzmic@gmail.com> Acked-by:
-
Finn Thain authored
At present, CONFIG_ADB_PMU depends on CONFIG_PPC_PMAC. When this gets relaxed to CONFIG_PPC_PMAC || CONFIG_MAC, those Kconfig symbols with implicit deps on PPC_PMAC will need explicit deps. Add them now. No functional change. Tested-by:
-
Finn Thain authored
Put #ifdefs around the Open Firmware, xmon, interrupt dispatch, battery and suspend code. Add the necessary interrupt handling to support m68k PowerBooks. The pmu_kind value is available to userspace using the PMU_IOC_GET_MODEL ioctl. It is not clear yet what hardware classes are be needed to describe m68k PowerBook models, so pmu_kind is given the provisional value PMU_UNKNOWN. To find out about the hardware, user programs can use /proc/bootinfo or /proc/hardware, or send the PMU_GET_VERSION command using /dev/adb. Tested-by:
-
Finn Thain authored
On most PowerPC Macs, the PMU driver uses the shift register and IO port B from a single VIA chip. On 68k and early PowerPC PowerBooks, the driver uses the shift register from one VIA chip together with IO port B from another. Replace via with via1 and via2 to accommodate this. For the CONFIG_PPC_PMAC case, set via1 = via2 so there is no change. Tested-by:
-
Finn Thain authored
On 68k Macs, the via/vias pointer can't be used to determine whether the PMU driver has been initialized. For portability, add a new state to indicate that via_find_pmu() succeeded. After via_find_pmu() executes, testing vias == NULL is equivalent to testing via == NULL. Replace these tests with pmu_state == uninitialized which is simpler and more consistent. No functional change. Tested-by:
-
Finn Thain authored
The shift register interrupt flag gets cleared in via_pmu_interrupt() and once again in pmu_sr_intr(). Fix this theoretical race condition. Tested-by:
-
Finn Thain authored
Add missing in_8() accessors to init_pmu() and pmu_sr_intr(). This fixes several sparse warnings: drivers/macintosh/via-pmu.c:536:29: warning: dereference of noderef expression drivers/macintosh/via-pmu.c:537:33: warning: dereference of noderef expression drivers/macintosh/via-pmu.c:1455:17: warning: dereference of noderef expression drivers/macintosh/via-pmu.c:1456:69: warning: dereference of noderef expression Tested-by:
-
Finn Thain authored
The pmu_init() function has the __init qualifier, but the ops struct that holds a pointer to it does not. This causes a build warning. The driver works fine because the pointer is only dereferenced early. The function is so small that there's negligible benefit from using the __init qualifier. Remove it to fix the warning, consistent with the other ADB drivers. Tested-by:
-
- 30 Jul, 2018 16 commits
-
-
Alexey Spirkov authored
mmu_init_secondary() calls ppc44x_pin_tlb() which is marked __init, leading to a warning: The function mmu_init_secondary() references the function __init ppc44x_pin_tlb(). There's no CPU hotplug support on 44x so mmu_init_secondary() will only be called at boot. Therefore we should mark it as __init. Signed-off-by:
Alexey Spirkov <alexeis@astrosoft.ru> [mpe: Flesh out change log details] Signed-off-by:
-
Michael Ellerman authored
Paul Menzel reported that kmemleak was producing reports such as: unreferenced object 0xc0000000f8b80000 (size 16384): comm "init", pid 1, jiffies 4294937416 (age 312.240s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000d997deb7>] __pud_alloc+0x80/0x190 [<0000000087f2e8a3>] move_page_tables+0xbac/0xdc0 [<00000000091e51c2>] shift_arg_pages+0xc0/0x210 [<00000000ab88670c>] setup_arg_pages+0x22c/0x2a0 [<0000000060871529>] load_elf_binary+0x41c/0x1648 [<00000000ecd9d2d4>] search_binary_handler.part.11+0xbc/0x280 [<0000000034e0cdd7>] __do_execve_file.isra.13+0x73c/0x940 [<000000005f953a6e>] sys_execve+0x58/0x70 [<000000009700a858>] system_call+0x5c/0x70 Indicating that a PUD was being leaked. However what's really happening is that kmemleak is not able to recognise the references from the PGD to the PUD, because they are not fully qualified pointers. We can confirm that in xmon, eg: Find the task struct for pid 1 "init": 0:mon> P task_struct ->thread.ksp PID PPID S P CMD c0000001fe7c0000 c0000001fe803960 1 0 S 13 systemd Dump virtual address 0 to find the PGD: 0:mon> dv 0 c0000001fe7c0000 pgd @ 0xc0000000f8b01000 Dump the memory of the PGD: 0:mon> d c0000000f8b01000 c0000000f8b01000 00000000f8b90000 0000000000000000 |................| c0000000f8b01010 0000000000000000 0000000000000000 |................| c0000000f8b01020 0000000000000000 0000000000000000 |................| c0000000f8b01030 0000000000000000 00000000f8b80000 |................| ^^^^^^^^^^^^^^^^ There we can see the reference to our supposedly leaked PUD. But because it's missing the leading 0xc, kmemleak won't recognise it. We can confirm it's still in use by translating an address that is mapped via it: 0:mon> dv 7fff94000000 c0000001fe7c0000 pgd @ 0xc0000000f8b01000 pgdp @ 0xc0000000f8b01038 = 0x00000000f8b80000 <-- pudp @ 0xc0000000f8b81ff8 = 0x00000000037c4000 pmdp @ 0xc0000000037c5ca0 = 0x00000000fbd89000 ptep @ 0xc0000000fbd89000 = 0xc0800001d5ce0386 Maps physical address = 0x00000001d5ce0000 Flags = Accessed Dirty Read Write The fix is fairly simple. We need to tell kmemleak to ignore PUD allocations and never report them as leaks. We can also tell it not to scan the PGD, because it will never find pointers in there. However it will still notice if we allocate a PGD and then leak it. Reported-by:Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by:
-
Christophe Leroy authored
Split asm/tlbflush.h into: asm/nohash/tlbflush.h asm/book3s/32/tlbflush.h asm/book3s/64/tlbflush.h (already existing) Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
-
Christophe Leroy authored
asm/tlbflush.h is only needed for: - using functions xxx_flush_tlb_xxx() - using MMU_NO_CONTEXT - including asm-generic/pgtable.h Signed-off-by:
-
Christophe Leroy authored
mmu-44x.h doesn't need asm/page.h if PAGE_SHIFT are replaced by CONFIG_PPC_XX_PAGES Signed-off-by:
-
Christophe Leroy authored
Signed-off-by:
-
Christophe Leroy authored
Remove superflous includes and add missing ones Signed-off-by:
-
Christophe Leroy authored
PPC_PIN_SIZE is specific to the 44x and is defined in mmu.h Signed-off-by:
-
Christophe Leroy authored
set_breakpoint() is only used in process.c so make it static Signed-off-by:
-
Christophe Leroy authored
Files not using fixmap consts or functions don't need asm/fixmap.h Signed-off-by:
-
Christophe Leroy authored
files not using feature fixup don't need asm/feature-fixups.h files using feature fixup need asm/feature-fixups.h Signed-off-by:
-
Christophe Leroy authored
Only include linux/stringify.h is files using __stringify() Signed-off-by:
-
Christophe Leroy authored
This patch moves ASM_CONST() and stringify_in_c() into dedicated asm-const.h, then cleans all related inclusions. Signed-off-by:
-
Christophe Leroy authored
Signed-off-by:
-
Christophe Leroy authored
Files not using cpu_has_feature() don't need cpu_has_feature.h Signed-off-by:
-
Christophe Leroy authored
page.h doesn't need kdump.h Signed-off-by:
-
- 24 Jul, 2018 5 commits
-
-
Nicholas Piggin authored
This delay was in the very first OPAL console commit 6.5 years ago, and came from the vio hvc driver. The firmware console has hardened sufficiently to remove it. Reviewed-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Nicholas Piggin authored
The RAW console does not need writes to be atomic, so relax opal_put_chars to be able to do partial writes, and implement an _atomic variant which does not take a spinlock. This API is used in xmon, so the less locking that is used, the better chance there is that a crash can be debugged. Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Nicholas Piggin authored
OPAL console writes do not have to synchronously flush firmware / hardware buffers unless they are going through the udbg path. Remove the unconditional flushing from opal_put_chars. Flush if there was no space in the buffer as an optimisation (callers loop waiting for success in that case). udbg flushing is moved to udbg_opal_putc. Signed-off-by:
-
Nicholas Piggin authored
opal_put_chars deals with partial writes because in OPALv1, opal_console_write_buffer_space did not work correctly. That firmware is not supported. This reworks the opal_put_chars code to no longer deal with partial writes by turning them into full writes. Partial write handling is still supported in terms of what gets returned to the caller, but it may not go to the console atomically. A warning message is printed in this case. This allows console flushing to be moved out of the opal_write_lock spinlock. That could cause the lock to be held for long periods if the console is busy (especially if it was being spammed by firmware), which is dangerous because the lock is taken by xmon to debug the system. Flushing outside the lock improves the situation a bit. Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Nicholas Piggin authored
A new console flushing firmware API was introduced to replace event polling loops, and implemented in opal-kmsg with affddff6 ("powerpc/powernv: Add a kmsg_dumper that flushes console output on panic"), to flush the console in the panic path. The OPAL console driver has other situations where interrupts are off and it needs to flush the console synchronously. These still use a polling loop. So move the opal-kmsg flush code to opal_flush_console, and use the new function in opal-kmsg and opal_put_chars. Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by:
Russell Currey <ruscur@russell.cc> Signed-off-by:
-
